// mavlink_motor_test_start - start motor test - spin a single motor at a specified pwm
// returns MAV_RESULT_ACCEPTED on success, MAV_RESULT_FAILED on failure
MAV_RESULT Copter::mavlink_motor_test_start(mavlink_channel_t chan, uint8_t motor_seq, uint8_t throttle_type, uint16_t throttle_value,
float timeout_sec, uint8_t motor_count)
{
if (motor_count == 0) {
motor_count = 1;
}
// if test has not started try to start it
if (!ap.motor_test) {
gcs().send_text(MAV_SEVERITY_INFO, "starting motor test");
/* perform checks that it is ok to start test
The RC calibrated check can be skipped if direct pwm is
supplied
*/
if (!mavlink_motor_test_check(chan, throttle_type != 1)) {
return MAV_RESULT_FAILED;
} else {
// start test
ap.motor_test = true;
// enable and arm motors
if (!motors->armed()) {
init_rc_out();
enable_motor_output();
motors->armed(true);
}
// disable throttle and gps failsafe
g.failsafe_throttle = FS_THR_DISABLED;
g.failsafe_gcs = FS_GCS_DISABLED;
g.fs_ekf_action = 0;
// turn on notify leds
AP_Notify::flags.esc_calibration = true;
}
}
// set timeout
motor_test_start_ms = AP_HAL::millis();
motor_test_timeout_ms = MIN(timeout_sec, MOTOR_TEST_TIMEOUT_SEC) * 1000;
// store required output
motor_test_seq = motor_seq;
motor_test_count = motor_count;
motor_test_throttle_type = throttle_type;
motor_test_throttle_value = throttle_value;
if (motor_test_throttle_type == MOTOR_TEST_COMPASS_CAL) {
compass.per_motor_calibration_start();
}
// return success
return MAV_RESULT_ACCEPTED;
}
// mavlink_motor_test_start - start motor test - spin a single motor at a specified pwm
// returns MAV_RESULT_ACCEPTED on success, MAV_RESULT_FAILED on failure
uint8_t Copter::mavlink_motor_test_start(mavlink_channel_t chan, uint8_t motor_seq, uint8_t throttle_type, uint16_t throttle_value, float timeout_sec)
{
// if test has not started try to start it
if (!ap.motor_test) {
/* perform checks that it is ok to start test
The RC calibrated check can be skipped if direct pwm is
supplied
*/
if (!mavlink_motor_test_check(chan, throttle_type != 1)) {
return MAV_RESULT_FAILED;
} else {
// start test
ap.motor_test = true;
// enable and arm motors
if (!motors->armed()) {
init_rc_out();
enable_motor_output();
motors->armed(true);
}
// disable throttle, battery and gps failsafe
g.failsafe_throttle = FS_THR_DISABLED;
g.failsafe_battery_enabled = FS_BATT_DISABLED;
g.failsafe_gcs = FS_GCS_DISABLED;
// turn on notify leds
AP_Notify::flags.esc_calibration = true;
}
}
// set timeout
motor_test_start_ms = AP_HAL::millis();
motor_test_timeout_ms = MIN(timeout_sec * 1000, MOTOR_TEST_TIMEOUT_MS_MAX);
// store required output
motor_test_seq = motor_seq;
motor_test_throttle_type = throttle_type;
motor_test_throttle_value = throttle_value;
// return success
return MAV_RESULT_ACCEPTED;
}
void Plane::init_ardupilot()
{
// initialise serial port
serial_manager.init_console();
cliSerial->printf_P(PSTR("\n\nInit " FIRMWARE_STRING
"\n\nFree RAM: %u\n"),
hal.util->available_memory());
//
// Check the EEPROM format version before loading any parameters from EEPROM
//
load_parameters();
if (g.hil_mode == 1) {
// set sensors to HIL mode
ins.set_hil_mode();
compass.set_hil_mode();
barometer.set_hil_mode();
}
#if CONFIG_HAL_BOARD == HAL_BOARD_PX4
// this must be before BoardConfig.init() so if
// BRD_SAFETYENABLE==0 then we don't have safety off yet
for (uint8_t tries=0; tries<10; tries++) {
if (setup_failsafe_mixing()) {
break;
}
hal.scheduler->delay(10);
}
#endif
BoardConfig.init();
// initialise serial ports
serial_manager.init();
// allow servo set on all channels except first 4
ServoRelayEvents.set_channel_mask(0xFFF0);
set_control_channels();
// keep a record of how many resets have happened. This can be
// used to detect in-flight resets
g.num_resets.set_and_save(g.num_resets+1);
// init baro before we start the GCS, so that the CLI baro test works
barometer.init();
// initialise rangefinder
init_rangefinder();
// initialise battery monitoring
battery.init();
// init the GCS
gcs[0].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_Console, 0);
// we start by assuming USB connected, as we initialed the serial
// port with SERIAL0_BAUD. check_usb_mux() fixes this if need be.
usb_connected = true;
check_usb_mux();
// setup serial port for telem1
gcs[1].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 0);
#if MAVLINK_COMM_NUM_BUFFERS > 2
// setup serial port for telem2
gcs[2].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 1);
#endif
#if MAVLINK_COMM_NUM_BUFFERS > 3
// setup serial port for fourth telemetry port (not used by default)
gcs[3].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 2);
#endif
// setup frsky
#if FRSKY_TELEM_ENABLED == ENABLED
frsky_telemetry.init(serial_manager);
#endif
mavlink_system.sysid = g.sysid_this_mav;
#if LOGGING_ENABLED == ENABLED
log_init();
#endif
#if CONFIG_HAL_BOARD == HAL_BOARD_APM1
apm1_adc.Init(); // APM ADC library initialization
#endif
// initialise airspeed sensor
airspeed.init();
if (g.compass_enabled==true) {
if (!compass.init() || !compass.read()) {
cliSerial->println_P(PSTR("Compass initialisation failed!"));
g.compass_enabled = false;
} else {
ahrs.set_compass(&compass);
}
}
#if OPTFLOW == ENABLED
// make optflow available to libraries
ahrs.set_optflow(&optflow);
#endif
// Register mavlink_delay_cb, which will run anytime you have
// more than 5ms remaining in your call to hal.scheduler->delay
hal.scheduler->register_delay_callback(mavlink_delay_cb_static, 5);
// give AHRS the airspeed sensor
ahrs.set_airspeed(&airspeed);
// GPS Initialization
gps.init(&DataFlash, serial_manager);
init_rc_in(); // sets up rc channels from radio
init_rc_out(); // sets up the timer libs
relay.init();
#if MOUNT == ENABLED
// initialise camera mount
camera_mount.init(serial_manager);
#endif
#if FENCE_TRIGGERED_PIN > 0
hal.gpio->pinMode(FENCE_TRIGGERED_PIN, HAL_GPIO_OUTPUT);
hal.gpio->write(FENCE_TRIGGERED_PIN, 0);
#endif
/*
* setup the 'main loop is dead' check. Note that this relies on
* the RC library being initialised.
*/
hal.scheduler->register_timer_failsafe(failsafe_check_static, 1000);
#if CLI_ENABLED == ENABLED
if (g.cli_enabled == 1) {
const prog_char_t *msg = PSTR("\nPress ENTER 3 times to start interactive setup\n");
cliSerial->println_P(msg);
if (gcs[1].initialised && (gcs[1].get_uart() != NULL)) {
gcs[1].get_uart()->println_P(msg);
}
if (num_gcs > 2 && gcs[2].initialised && (gcs[2].get_uart() != NULL)) {
gcs[2].get_uart()->println_P(msg);
}
}
#endif // CLI_ENABLED
startup_ground();
Log_Write_Startup(TYPE_GROUNDSTART_MSG);
// choose the nav controller
set_nav_controller();
set_mode((FlightMode)g.initial_mode.get());
// set the correct flight mode
// ---------------------------
reset_control_switch();
// initialise sensor
#if OPTFLOW == ENABLED
optflow.init();
#endif
}
void Copter::init_ardupilot()
{
if (!hal.gpio->usb_connected()) {
// USB is not connected, this means UART0 may be a Xbee, with
// its darned bricking problem. We can't write to it for at
// least one second after powering up. Simplest solution for
// now is to delay for 1 second. Something more elegant may be
// added later
delay(1000);
}
// initialise serial port
serial_manager.init_console();
// init vehicle capabilties
init_capabilities();
cliSerial->printf("\n\nInit " FIRMWARE_STRING
"\n\nFree RAM: %u\n",
(unsigned)hal.util->available_memory());
//
// Report firmware version code expect on console (check of actual EEPROM format version is done in load_parameters function)
//
report_version();
// load parameters from EEPROM
load_parameters();
BoardConfig.init();
// initialise serial port
serial_manager.init();
// init EPM cargo gripper
#if EPM_ENABLED == ENABLED
epm.init();
#endif
// initialise notify system
// disable external leds if epm is enabled because of pin conflict on the APM
notify.init(true);
// initialise battery monitor
battery.init();
// Init RSSI
rssi.init();
barometer.init();
// Register the mavlink service callback. This will run
// anytime there are more than 5ms remaining in a call to
// hal.scheduler->delay.
hal.scheduler->register_delay_callback(mavlink_delay_cb_static, 5);
// we start by assuming USB connected, as we initialed the serial
// port with SERIAL0_BAUD. check_usb_mux() fixes this if need be.
ap.usb_connected = true;
check_usb_mux();
// init the GCS connected to the console
gcs[0].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_Console, 0);
// init telemetry port
gcs[1].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 0);
// setup serial port for telem2
gcs[2].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 1);
// setup serial port for fourth telemetry port (not used by default)
gcs[3].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 2);
#if FRSKY_TELEM_ENABLED == ENABLED
// setup frsky
frsky_telemetry.init(serial_manager);
#endif
// identify ourselves correctly with the ground station
mavlink_system.sysid = g.sysid_this_mav;
#if LOGGING_ENABLED == ENABLED
log_init();
#endif
GCS_MAVLINK::set_dataflash(&DataFlash);
// update motor interlock state
update_using_interlock();
#if FRAME_CONFIG == HELI_FRAME
// trad heli specific initialisation
heli_init();
#endif
init_rc_in(); // sets up rc channels from radio
init_rc_out(); // sets up motors and output to escs
// initialise which outputs Servo and Relay events can use
ServoRelayEvents.set_channel_mask(~motors.get_motor_mask());
relay.init();
/*
* setup the 'main loop is dead' check. Note that this relies on
* the RC library being initialised.
*/
hal.scheduler->register_timer_failsafe(failsafe_check_static, 1000);
// Do GPS init
gps.init(&DataFlash, serial_manager);
if(g.compass_enabled)
init_compass();
#if OPTFLOW == ENABLED
// make optflow available to AHRS
ahrs.set_optflow(&optflow);
#endif
// init Location class
Location_Class::set_ahrs(&ahrs);
#if AP_TERRAIN_AVAILABLE && AC_TERRAIN
Location_Class::set_terrain(&terrain);
wp_nav.set_terrain(&terrain);
#endif
pos_control.set_dt(MAIN_LOOP_SECONDS);
// init the optical flow sensor
init_optflow();
#if MOUNT == ENABLED
// initialise camera mount
camera_mount.init(&DataFlash, serial_manager);
#endif
#if PRECISION_LANDING == ENABLED
// initialise precision landing
init_precland();
#endif
#ifdef USERHOOK_INIT
USERHOOK_INIT
#endif
#if CLI_ENABLED == ENABLED
if (g.cli_enabled) {
const char *msg = "\nPress ENTER 3 times to start interactive setup\n";
cliSerial->println(msg);
if (gcs[1].initialised && (gcs[1].get_uart() != NULL)) {
gcs[1].get_uart()->println(msg);
}
if (num_gcs > 2 && gcs[2].initialised && (gcs[2].get_uart() != NULL)) {
gcs[2].get_uart()->println(msg);
}
}
#endif // CLI_ENABLED
#if HIL_MODE != HIL_MODE_DISABLED
while (barometer.get_last_update() == 0) {
// the barometer begins updating when we get the first
// HIL_STATE message
gcs_send_text(MAV_SEVERITY_WARNING, "Waiting for first HIL_STATE message");
delay(1000);
}
// set INS to HIL mode
ins.set_hil_mode();
#endif
// read Baro pressure at ground
//-----------------------------
init_barometer(true);
// initialise sonar
#if CONFIG_SONAR == ENABLED
init_sonar();
#endif
// initialise AP_RPM library
rpm_sensor.init();
// initialise mission library
mission.init();
// initialise the flight mode and aux switch
// ---------------------------
reset_control_switch();
init_aux_switches();
startup_INS_ground();
// set landed flags
set_land_complete(true);
set_land_complete_maybe(true);
// we don't want writes to the serial port to cause us to pause
// mid-flight, so set the serial ports non-blocking once we are
// ready to fly
serial_manager.set_blocking_writes_all(false);
// enable CPU failsafe
failsafe_enable();
ins.set_raw_logging(should_log(MASK_LOG_IMU_RAW));
ins.set_dataflash(&DataFlash);
cliSerial->print("\nReady to FLY ");
// flag that initialisation has completed
ap.initialised = true;
}
// setup_compassmot - sets compass's motor interference parameters
uint8_t Copter::mavlink_compassmot(mavlink_channel_t chan)
{
#if FRAME_CONFIG == HELI_FRAME
// compassmot not implemented for tradheli
return 1;
#else
int8_t comp_type; // throttle or current based compensation
Vector3f compass_base[COMPASS_MAX_INSTANCES]; // compass vector when throttle is zero
Vector3f motor_impact[COMPASS_MAX_INSTANCES]; // impact of motors on compass vector
Vector3f motor_impact_scaled[COMPASS_MAX_INSTANCES]; // impact of motors on compass vector scaled with throttle
Vector3f motor_compensation[COMPASS_MAX_INSTANCES]; // final compensation to be stored to eeprom
float throttle_pct; // throttle as a percentage 0.0 ~ 1.0
float throttle_pct_max = 0.0f; // maximum throttle reached (as a percentage 0~1.0)
float current_amps_max = 0.0f; // maximum current reached
float interference_pct[COMPASS_MAX_INSTANCES]; // interference as a percentage of total mag field (for reporting purposes only)
uint32_t last_run_time;
uint32_t last_send_time;
bool updated = false; // have we updated the compensation vector at least once
uint8_t command_ack_start = command_ack_counter;
// exit immediately if we are already in compassmot
if (ap.compass_mot) {
// ignore restart messages
return 1;
}else{
ap.compass_mot = true;
}
// initialise output
for (uint8_t i=0; i<COMPASS_MAX_INSTANCES; i++) {
interference_pct[i] = 0.0f;
}
// check compass is enabled
if (!g.compass_enabled) {
gcs[chan-MAVLINK_COMM_0].send_text(MAV_SEVERITY_CRITICAL, "Compass disabled");
ap.compass_mot = false;
return 1;
}
// check compass health
compass.read();
for (uint8_t i=0; i<compass.get_count(); i++) {
if (!compass.healthy(i)) {
gcs[chan-MAVLINK_COMM_0].send_text(MAV_SEVERITY_CRITICAL, "Check compass");
ap.compass_mot = false;
return 1;
}
}
// check if radio is calibrated
pre_arm_rc_checks();
if (!ap.pre_arm_rc_check) {
gcs[chan-MAVLINK_COMM_0].send_text(MAV_SEVERITY_CRITICAL, "RC not calibrated");
ap.compass_mot = false;
return 1;
}
// check throttle is at zero
read_radio();
if (channel_throttle->control_in != 0) {
gcs[chan-MAVLINK_COMM_0].send_text(MAV_SEVERITY_CRITICAL, "Throttle not zero");
ap.compass_mot = false;
return 1;
}
// check we are landed
if (!ap.land_complete) {
gcs[chan-MAVLINK_COMM_0].send_text(MAV_SEVERITY_CRITICAL, "Not landed");
ap.compass_mot = false;
return 1;
}
// disable cpu failsafe
failsafe_disable();
// initialise compass
init_compass();
// default compensation type to use current if possible
if (battery.has_current()) {
comp_type = AP_COMPASS_MOT_COMP_CURRENT;
}else{
comp_type = AP_COMPASS_MOT_COMP_THROTTLE;
}
// send back initial ACK
mavlink_msg_command_ack_send(chan, MAV_CMD_PREFLIGHT_CALIBRATION,0);
// flash leds
AP_Notify::flags.esc_calibration = true;
// warn user we are starting calibration
gcs[chan-MAVLINK_COMM_0].send_text(MAV_SEVERITY_INFO, "Starting calibration");
// inform what type of compensation we are attempting
if (comp_type == AP_COMPASS_MOT_COMP_CURRENT) {
gcs[chan-MAVLINK_COMM_0].send_text(MAV_SEVERITY_INFO, "Current");
} else{
gcs[chan-MAVLINK_COMM_0].send_text(MAV_SEVERITY_INFO, "Throttle");
}
// disable throttle and battery failsafe
g.failsafe_throttle = FS_THR_DISABLED;
g.failsafe_battery_enabled = FS_BATT_DISABLED;
// disable motor compensation
compass.motor_compensation_type(AP_COMPASS_MOT_COMP_DISABLED);
for (uint8_t i=0; i<compass.get_count(); i++) {
compass.set_motor_compensation(i, Vector3f(0,0,0));
}
// get initial compass readings
last_run_time = millis();
while ( millis() - last_run_time < 500 ) {
compass.accumulate();
}
compass.read();
// store initial x,y,z compass values
// initialise interference percentage
for (uint8_t i=0; i<compass.get_count(); i++) {
compass_base[i] = compass.get_field(i);
interference_pct[i] = 0.0f;
}
// enable motors and pass through throttle
init_rc_out();
enable_motor_output();
motors.armed(true);
// initialise run time
last_run_time = millis();
last_send_time = millis();
// main run while there is no user input and the compass is healthy
while (command_ack_start == command_ack_counter && compass.healthy(compass.get_primary()) && motors.armed()) {
// 50hz loop
if (millis() - last_run_time < 20) {
// grab some compass values
compass.accumulate();
hal.scheduler->delay(5);
continue;
}
last_run_time = millis();
// read radio input
read_radio();
// pass through throttle to motors
motors.throttle_pass_through(channel_throttle->radio_in);
// read some compass values
compass.read();
// read current
read_battery();
// calculate scaling for throttle
throttle_pct = (float)channel_throttle->control_in / 1000.0f;
throttle_pct = constrain_float(throttle_pct,0.0f,1.0f);
// if throttle is near zero, update base x,y,z values
if (throttle_pct <= 0.0f) {
for (uint8_t i=0; i<compass.get_count(); i++) {
compass_base[i] = compass_base[i] * 0.99f + compass.get_field(i) * 0.01f;
}
// causing printing to happen as soon as throttle is lifted
} else {
// calculate diff from compass base and scale with throttle
for (uint8_t i=0; i<compass.get_count(); i++) {
motor_impact[i] = compass.get_field(i) - compass_base[i];
}
// throttle based compensation
if (comp_type == AP_COMPASS_MOT_COMP_THROTTLE) {
// for each compass
for (uint8_t i=0; i<compass.get_count(); i++) {
// scale by throttle
motor_impact_scaled[i] = motor_impact[i] / throttle_pct;
// adjust the motor compensation to negate the impact
motor_compensation[i] = motor_compensation[i] * 0.99f - motor_impact_scaled[i] * 0.01f;
}
updated = true;
} else {
// for each compass
for (uint8_t i=0; i<compass.get_count(); i++) {
// current based compensation if more than 3amps being drawn
motor_impact_scaled[i] = motor_impact[i] / battery.current_amps();
// adjust the motor compensation to negate the impact if drawing over 3amps
if (battery.current_amps() >= 3.0f) {
motor_compensation[i] = motor_compensation[i] * 0.99f - motor_impact_scaled[i] * 0.01f;
updated = true;
}
}
}
// calculate interference percentage at full throttle as % of total mag field
if (comp_type == AP_COMPASS_MOT_COMP_THROTTLE) {
for (uint8_t i=0; i<compass.get_count(); i++) {
// interference is impact@fullthrottle / mag field * 100
interference_pct[i] = motor_compensation[i].length() / (float)COMPASS_MAGFIELD_EXPECTED * 100.0f;
}
}else{
for (uint8_t i=0; i<compass.get_count(); i++) {
// interference is impact/amp * (max current seen / max throttle seen) / mag field * 100
interference_pct[i] = motor_compensation[i].length() * (current_amps_max/throttle_pct_max) / (float)COMPASS_MAGFIELD_EXPECTED * 100.0f;
}
}
// record maximum throttle and current
throttle_pct_max = MAX(throttle_pct_max, throttle_pct);
current_amps_max = MAX(current_amps_max, battery.current_amps());
}
if (AP_HAL::millis() - last_send_time > 500) {
last_send_time = AP_HAL::millis();
mavlink_msg_compassmot_status_send(chan,
channel_throttle->control_in,
battery.current_amps(),
interference_pct[compass.get_primary()],
motor_compensation[compass.get_primary()].x,
motor_compensation[compass.get_primary()].y,
motor_compensation[compass.get_primary()].z);
}
}
// stop motors
motors.output_min();
motors.armed(false);
// set and save motor compensation
if (updated) {
compass.motor_compensation_type(comp_type);
for (uint8_t i=0; i<compass.get_count(); i++) {
compass.set_motor_compensation(i, motor_compensation[i]);
}
compass.save_motor_compensation();
// display success message
gcs[chan-MAVLINK_COMM_0].send_text(MAV_SEVERITY_INFO, "Calibration successful");
} else {
// compensation vector never updated, report failure
gcs[chan-MAVLINK_COMM_0].send_text(MAV_SEVERITY_NOTICE, "Failed");
compass.motor_compensation_type(AP_COMPASS_MOT_COMP_DISABLED);
}
// display new motor offsets and save
report_compass();
// turn off notify leds
AP_Notify::flags.esc_calibration = false;
// re-enable cpu failsafe
failsafe_enable();
// re-enable failsafes
g.failsafe_throttle.load();
g.failsafe_battery_enabled.load();
// flag we have completed
ap.compass_mot = false;
return 0;
#endif // FRAME_CONFIG != HELI_FRAME
}
void Rover::init_ardupilot()
{
// initialise console serial port
serial_manager.init_console();
cliSerial->printf("\n\nInit " FIRMWARE_STRING
"\n\nFree RAM: %u\n",
hal.util->available_memory());
//
// Check the EEPROM format version before loading any parameters from EEPROM.
//
load_parameters();
BoardConfig.init();
// initialise serial ports
serial_manager.init();
ServoRelayEvents.set_channel_mask(0xFFF0);
set_control_channels();
battery.init();
// keep a record of how many resets have happened. This can be
// used to detect in-flight resets
g.num_resets.set_and_save(g.num_resets+1);
// init baro before we start the GCS, so that the CLI baro test works
barometer.init();
// init the GCS
gcs[0].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_Console, 0);
// we start by assuming USB connected, as we initialed the serial
// port with SERIAL0_BAUD. check_usb_mux() fixes this if need be.
usb_connected = true;
check_usb_mux();
// setup serial port for telem1
gcs[1].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 0);
// setup serial port for telem2
gcs[2].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 1);
// setup serial port for fourth telemetry port (not used by default)
gcs[3].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, 2);
// setup frsky telemetry
#if FRSKY_TELEM_ENABLED == ENABLED
frsky_telemetry.init(serial_manager);
#endif
mavlink_system.sysid = g.sysid_this_mav;
#if LOGGING_ENABLED == ENABLED
log_init();
#endif
// Register mavlink_delay_cb, which will run anytime you have
// more than 5ms remaining in your call to hal.scheduler->delay
hal.scheduler->register_delay_callback(mavlink_delay_cb_static, 5);
if (g.compass_enabled==true) {
if (!compass.init()|| !compass.read()) {
cliSerial->println("Compass initialisation failed!");
g.compass_enabled = false;
} else {
ahrs.set_compass(&compass);
//compass.get_offsets(); // load offsets to account for airframe magnetic interference
}
}
// initialise sonar
init_sonar();
// and baro for EKF
init_barometer();
// Do GPS init
gps.init(&DataFlash, serial_manager);
rc_override_active = hal.rcin->set_overrides(rc_override, 8);
init_rc_in(); // sets up rc channels from radio
init_rc_out(); // sets up the timer libs
relay.init();
#if MOUNT == ENABLED
// initialise camera mount
camera_mount.init(serial_manager);
#endif
/*
setup the 'main loop is dead' check. Note that this relies on
the RC library being initialised.
*/
hal.scheduler->register_timer_failsafe(failsafe_check_static, 1000);
#if CLI_ENABLED == ENABLED
// If the switch is in 'menu' mode, run the main menu.
//
// Since we can't be sure that the setup or test mode won't leave
// the system in an odd state, we don't let the user exit the top
// menu; they must reset in order to fly.
//
if (g.cli_enabled == 1) {
const char *msg = "\nPress ENTER 3 times to start interactive setup\n";
cliSerial->println(msg);
if (gcs[1].initialised && (gcs[1].get_uart() != NULL)) {
gcs[1].get_uart()->println(msg);
}
if (num_gcs > 2 && gcs[2].initialised && (gcs[2].get_uart() != NULL)) {
gcs[2].get_uart()->println(msg);
}
}
#endif
init_capabilities();
startup_ground();
set_mode((enum mode)g.initial_mode.get());
// set the correct flight mode
// ---------------------------
reset_control_switch();
}
void Sub::init_ardupilot()
{
if (!hal.gpio->usb_connected()) {
// USB is not connected, this means UART0 may be a Xbee, with
// its darned bricking problem. We can't write to it for at
// least one second after powering up. Simplest solution for
// now is to delay for 1 second. Something more elegant may be
// added later
hal.scheduler->delay(1000);
}
// initialise serial port
serial_manager.init_console();
cliSerial->printf("\n\nInit " FIRMWARE_STRING
"\n\nFree RAM: %u\n",
(unsigned)hal.util->available_memory());
//
// Report firmware version code expect on console (check of actual EEPROM format version is done in load_parameters function)
//
report_version();
// load parameters from EEPROM
load_parameters();
BoardConfig.init();
// initialise serial port
serial_manager.init();
// init cargo gripper
#if GRIPPER_ENABLED == ENABLED
g2.gripper.init();
#endif
// initialise notify system
notify.init(true);
// initialise battery monitor
battery.init();
barometer.init();
celsius.init();
// Register the mavlink service callback. This will run
// anytime there are more than 5ms remaining in a call to
// hal.scheduler->delay.
hal.scheduler->register_delay_callback(mavlink_delay_cb_static, 5);
// we start by assuming USB connected, as we initialed the serial
// port with SERIAL0_BAUD. check_usb_mux() fixes this if need be.
ap.usb_connected = true;
check_usb_mux();
// setup telem slots with serial ports
for (uint8_t i = 0; i < MAVLINK_COMM_NUM_BUFFERS; i++) {
gcs_chan[i].setup_uart(serial_manager, AP_SerialManager::SerialProtocol_MAVLink, i);
}
// identify ourselves correctly with the ground station
mavlink_system.sysid = g.sysid_this_mav;
#if LOGGING_ENABLED == ENABLED
log_init();
#endif
gcs().set_dataflash(&DataFlash);
init_rc_in(); // sets up rc channels from radio
init_rc_out(); // sets up motors and output to escs
init_joystick(); // joystick initialization
// initialise which outputs Servo and Relay events can use
ServoRelayEvents.set_channel_mask(~motors.get_motor_mask());
relay.init();
/*
* setup the 'main loop is dead' check. Note that this relies on
* the RC library being initialised.
*/
hal.scheduler->register_timer_failsafe(failsafe_check_static, 1000);
// Do GPS init
gps.init(&DataFlash, serial_manager);
if (g.compass_enabled) {
init_compass();
}
#if OPTFLOW == ENABLED
// make optflow available to AHRS
ahrs.set_optflow(&optflow);
#endif
// init Location class
Location_Class::set_ahrs(&ahrs);
#if AP_TERRAIN_AVAILABLE && AC_TERRAIN
Location_Class::set_terrain(&terrain);
wp_nav.set_terrain(&terrain);
#endif
#if AVOIDANCE_ENABLED == ENABLED
wp_nav.set_avoidance(&avoid);
#endif
pos_control.set_dt(MAIN_LOOP_SECONDS);
// init the optical flow sensor
init_optflow();
#if MOUNT == ENABLED
// initialise camera mount
camera_mount.init(&DataFlash, serial_manager);
#endif
#ifdef USERHOOK_INIT
USERHOOK_INIT
#endif
#if CLI_ENABLED == ENABLED
if (g.cli_enabled) {
const char *msg = "\nPress ENTER 3 times to start interactive setup\n";
cliSerial->println(msg);
if (gcs_chan[1].initialised && (gcs_chan[1].get_uart() != NULL)) {
gcs_chan[1].get_uart()->println(msg);
}
if (num_gcs > 2 && gcs_chan[2].initialised && (gcs_chan[2].get_uart() != NULL)) {
gcs_chan[2].get_uart()->println(msg);
}
}
#endif // CLI_ENABLED
#if HIL_MODE != HIL_MODE_DISABLED
while (barometer.get_last_update() == 0) {
// the barometer begins updating when we get the first
// HIL_STATE message
gcs_send_text(MAV_SEVERITY_WARNING, "Waiting for first HIL_STATE message");
hal.scheduler->delay(1000);
}
// set INS to HIL mode
ins.set_hil_mode();
#endif
// read Baro pressure at ground
//-----------------------------
init_barometer(false);
barometer.update();
for (uint8_t i = 0; i < barometer.num_instances(); i++) {
if (barometer.get_type(i) == AP_Baro::BARO_TYPE_WATER && barometer.healthy(i)) {
barometer.set_primary_baro(i);
ap.depth_sensor_present = true;
break;
}
}
if (!ap.depth_sensor_present) {
// We only have onboard baro
// No external underwater depth sensor detected
barometer.set_primary_baro(0);
EKF2.set_baro_alt_noise(10.0f); // Readings won't correspond with rest of INS
EKF3.set_baro_alt_noise(10.0f);
} else {
EKF2.set_baro_alt_noise(0.1f);
EKF3.set_baro_alt_noise(0.1f);
}
leak_detector.init();
// backwards compatibility
if (attitude_control.get_accel_yaw_max() < 110000.0f) {
attitude_control.save_accel_yaw_max(110000.0f);
}
last_pilot_heading = ahrs.yaw_sensor;
// initialise rangefinder
#if RANGEFINDER_ENABLED == ENABLED
init_rangefinder();
#endif
// initialise AP_RPM library
#if RPM_ENABLED == ENABLED
rpm_sensor.init();
#endif
// initialise mission library
mission.init();
startup_INS_ground();
// we don't want writes to the serial port to cause us to pause
// mid-flight, so set the serial ports non-blocking once we are
// ready to fly
serial_manager.set_blocking_writes_all(false);
// enable CPU failsafe
failsafe_enable();
ins.set_raw_logging(should_log(MASK_LOG_IMU_RAW));
ins.set_dataflash(&DataFlash);
// init vehicle capabilties
init_capabilities();
cliSerial->print("\nReady to FLY ");
// flag that initialisation has completed
ap.initialised = true;
}