int iwl_power_set_mode(struct iwl_priv *priv, struct iwl_powertable_cmd *cmd,
bool force)
{
int ret;
bool update_chains;
lockdep_assert_held(&priv->mutex);
/* Don't update the RX chain when chain noise calibration is running */
update_chains = priv->chain_noise_data.state == IWL_CHAIN_NOISE_DONE ||
priv->chain_noise_data.state == IWL_CHAIN_NOISE_ALIVE;
if (!memcmp(&priv->power_data.sleep_cmd, cmd, sizeof(*cmd)) && !force)
return 0;
if (!iwl_is_ready_rf(priv))
return -EIO;
/* scan complete use sleep_power_next, need to be updated */
memcpy(&priv->power_data.sleep_cmd_next, cmd, sizeof(*cmd));
if (test_bit(STATUS_SCANNING, &priv->status) && !force) {
IWL_DEBUG_INFO(priv, "Defer power set mode while scanning\n");
return 0;
}
if (cmd->flags & IWL_POWER_DRIVER_ALLOW_SLEEP_MSK)
iwl_dvm_set_pmi(priv, true);
ret = iwl_set_power(priv, cmd);
if (!ret) {
if (!(cmd->flags & IWL_POWER_DRIVER_ALLOW_SLEEP_MSK))
iwl_dvm_set_pmi(priv, false);
if (update_chains)
iwl_update_chain_flags(priv);
else
IWL_DEBUG_POWER(priv,
"Cannot update the power, chain noise "
"calibration running: %d\n",
priv->chain_noise_data.state);
memcpy(&priv->power_data.sleep_cmd, cmd, sizeof(*cmd));
} else
IWL_ERR(priv, "set power fail, ret = %d\n", ret);
return ret;
}
static void iwlagn_bt_traffic_change_work(struct work_struct *work)
{
struct iwl_priv *priv =
container_of(work, struct iwl_priv, bt_traffic_change_work);
struct iwl_rxon_context *ctx;
int smps_request = -1;
if (priv->bt_enable_flag == IWLAGN_BT_FLAG_COEX_MODE_DISABLED) {
/* bt coex disabled */
return;
}
/*
* Note: bt_traffic_load can be overridden by scan complete and
* coex profile notifications. Ignore that since only bad consequence
* can be not matching debug print with actual state.
*/
IWL_DEBUG_COEX(priv, "BT traffic load changes: %d\n",
priv->bt_traffic_load);
switch (priv->bt_traffic_load) {
case IWL_BT_COEX_TRAFFIC_LOAD_NONE:
if (priv->bt_status)
smps_request = IEEE80211_SMPS_DYNAMIC;
else
smps_request = IEEE80211_SMPS_AUTOMATIC;
break;
case IWL_BT_COEX_TRAFFIC_LOAD_LOW:
smps_request = IEEE80211_SMPS_DYNAMIC;
break;
case IWL_BT_COEX_TRAFFIC_LOAD_HIGH:
case IWL_BT_COEX_TRAFFIC_LOAD_CONTINUOUS:
smps_request = IEEE80211_SMPS_STATIC;
break;
default:
IWL_ERR(priv, "Invalid BT traffic load: %d\n",
priv->bt_traffic_load);
break;
}
mutex_lock(&priv->mutex);
/*
* We can not send command to firmware while scanning. When the scan
* complete we will schedule this work again. We do check with mutex
* locked to prevent new scan request to arrive. We do not check
* STATUS_SCANNING to avoid race when queue_work two times from
* different notifications, but quit and not perform any work at all.
*/
if (test_bit(STATUS_SCAN_HW, &priv->status))
goto out;
iwl_update_chain_flags(priv);
if (smps_request != -1) {
priv->current_ht_config.smps = smps_request;
for_each_context(priv, ctx) {
if (ctx->vif && ctx->vif->type == NL80211_IFTYPE_STATION)
ieee80211_request_smps(ctx->vif, smps_request);
}
}
