/**
* @brief This function handles disconnect event. it
* reports disconnect to upper layer, clean tx/rx packets,
* reset link state etc.
*
* @param priv A pointer to struct lbs_private structure
* @return n/a
*/
void lbs_mac_event_disconnected(struct lbs_private *priv)
{
if (priv->connect_status != LBS_CONNECTED)
return;
lbs_deb_enter(LBS_DEB_ASSOC);
/*
* Cisco AP sends EAP failure and de-auth in less than 0.5 ms.
* It causes problem in the Supplicant
*/
msleep_interruptible(1000);
if (priv->wdev->iftype == NL80211_IFTYPE_STATION)
lbs_send_disconnect_notification(priv);
/* report disconnect to upper layer */
netif_stop_queue(priv->dev);
netif_carrier_off(priv->dev);
/* Free Tx and Rx packets */
kfree_skb(priv->currenttxskb);
priv->currenttxskb = NULL;
priv->tx_pending_len = 0;
priv->connect_status = LBS_DISCONNECTED;
if (priv->psstate != PS_STATE_FULL_POWER) {
/* make firmware to exit PS mode */
lbs_deb_cmd("disconnected, so exit PS mode\n");
lbs_set_ps_mode(priv, PS_MODE_ACTION_EXIT_PS, false);
}
lbs_deb_leave(LBS_DEB_ASSOC);
}
void lbs_mac_event_disconnected(struct lbs_private *priv)
{
if (priv->connect_status != LBS_CONNECTED)
return;
lbs_deb_enter(LBS_DEB_ASSOC);
/*
*/
msleep_interruptible(1000);
if (priv->wdev->iftype == NL80211_IFTYPE_STATION)
lbs_send_disconnect_notification(priv);
/* */
netif_stop_queue(priv->dev);
netif_carrier_off(priv->dev);
/* */
kfree_skb(priv->currenttxskb);
priv->currenttxskb = NULL;
priv->tx_pending_len = 0;
priv->connect_status = LBS_DISCONNECTED;
if (priv->psstate != PS_STATE_FULL_POWER) {
/* */
lbs_deb_cmd("disconnected, so exit PS mode\n");
lbs_set_ps_mode(priv, PS_MODE_ACTION_EXIT_PS, false);
}
lbs_deb_leave(LBS_DEB_ASSOC);
}
/**
* @brief This function handles disconnect event. it
* reports disconnect to upper layer, clean tx/rx packets,
* reset link state etc.
*
* @param priv A pointer to struct lbs_private structure
* @return n/a
*/
void lbs_mac_event_disconnected(struct lbs_private *priv)
{
if (priv->connect_status != LBS_CONNECTED)
return;
lbs_deb_enter(LBS_DEB_ASSOC);
/*
* Cisco AP sends EAP failure and de-auth in less than 0.5 ms.
* It causes problem in the Supplicant
*/
msleep_interruptible(1000);
lbs_send_disconnect_notification(priv);
/* report disconnect to upper layer */
netif_stop_queue(priv->dev);
netif_carrier_off(priv->dev);
/* Free Tx and Rx packets */
kfree_skb(priv->currenttxskb);
priv->currenttxskb = NULL;
priv->tx_pending_len = 0;
/* reset SNR/NF/RSSI values */
memset(priv->SNR, 0x00, sizeof(priv->SNR));
memset(priv->NF, 0x00, sizeof(priv->NF));
memset(priv->RSSI, 0x00, sizeof(priv->RSSI));
memset(priv->rawSNR, 0x00, sizeof(priv->rawSNR));
memset(priv->rawNF, 0x00, sizeof(priv->rawNF));
priv->nextSNRNF = 0;
priv->numSNRNF = 0;
priv->connect_status = LBS_DISCONNECTED;
/* Clear out associated SSID and BSSID since connection is
* no longer valid.
*/
memset(&priv->curbssparams.bssid, 0, ETH_ALEN);
memset(&priv->curbssparams.ssid, 0, IEEE80211_MAX_SSID_LEN);
priv->curbssparams.ssid_len = 0;
if (priv->psstate != PS_STATE_FULL_POWER) {
/* make firmware to exit PS mode */
lbs_deb_cmd("disconnected, so exit PS mode\n");
lbs_ps_wakeup(priv, 0);
}
lbs_deb_leave(LBS_DEB_ASSOC);
}
