/*---------------------------------------------------------------------------
功能： lcd 初始化
---------------------------------------------------------------------------*/
void __lcd_ili9325_init(void)
{
GPIO_PowerOn(CN_GPIO_F);
GPIO_PowerOn(CN_GPIO_G);
GPIO_CfgPinFunc(CN_GPIO_F,10,CN_GPIO_MODE_GPIO_OUT_OD_2Mhz);
GPIO_CfgPinFunc(CN_GPIO_G,8,CN_GPIO_MODE_GPIO_OUT_PP_2Mhz);
lcd_backlight_off();
lcd_reset();
Djy_DelayUs(100000);
if( __ili9325_read_reg() != 0x9325)
{
return;
}
__ili9325_write_reg(0x0000, 0x0001); //Start internal OSC
__ili9325_write_reg(0x0001, 0x0000); // set SS=0 and SM=0 S1---S720
__ili9325_write_reg(0x0002, 0x0700); // set 1 line inversion
__ili9325_write_reg(0x0003, 0x1030); // set GRAM write direction and BGR=1.
__ili9325_write_reg(0x0004, 0x0000); // Resize register
__ili9325_write_reg(0x0008, 0x0207); // set the back porch and front porch
__ili9325_write_reg(0x0009, 0x0000); // set non-display area refresh cycle ISC[3:0]
__ili9325_write_reg(0x000a, 0x0000); // FMARK function
__ili9325_write_reg(0x000c, 0x0000); // RGB interface setting
__ili9325_write_reg(0x000d, 0x0000); // Frame marker Position
__ili9325_write_reg(0x000f, 0x0000); // RGB interface polarity
//-------------power on sequence------------
__ili9325_write_reg(0x0010, 0x0000); // SAP, BT[3:0], AP, DSTB, SLP, STB
__ili9325_write_reg(0x0011, 0x0007); // DC1[2:0], DC0[2:0], VC[2:0]
__ili9325_write_reg(0x0012, 0x0000); // VREG1OUT voltage
__ili9325_write_reg(0x0013, 0x0000); // VDV[4:0] for VCOM amplitude
Djy_DelayUs(5000);
__ili9325_write_reg(0x0010, 0x1690); // SAP, BT[3:0], AP, DSTB, SLP, STB
__ili9325_write_reg(0x0011, 0x0227); // R11H=0x0221 at VCI=3.3V, DC1[2:0], DC0[2:0], VC[2:0]
Djy_DelayUs(5000);
__ili9325_write_reg(0x0012, 0x001d); // External reference voltage= Vci;001d
Djy_DelayUs(5000);
__ili9325_write_reg(0x0013, 0x0800); // R13H=1D00 when R12H=009D;VDV[4:0] for VCOM amplitude
__ili9325_write_reg(0x0029, 0x0014); // R29H=0013 when R12H=009D;VCM[5:0] for VCOMH
__ili9325_write_reg(0x002b, 0x000B); // Frame Rate = 96Hz
Djy_DelayUs(5000);
__ili9325_write_reg(0x0020, 0x0000); // GRAM horizontal Address
__ili9325_write_reg(0x0021, 0x0000); // GRAM Vertical Address
// ----------- Adjust the Gamma Curve ----------
__ili9325_write_reg(0x0030, 0x0007);
__ili9325_write_reg(0x0031, 0x0707);
__ili9325_write_reg(0x0032, 0x0006);
__ili9325_write_reg(0x0035, 0x0704);
__ili9325_write_reg(0x0036, 0x1F04);
__ili9325_write_reg(0x0037, 0x0004);
__ili9325_write_reg(0x0038, 0x0000);
__ili9325_write_reg(0x0039, 0x0706);
__ili9325_write_reg(0x003c, 0x0701);
__ili9325_write_reg(0x003d, 0x000F);
// ------------------ Set GRAM area ---------------
__ili9325_write_reg(0x0050, 0x0000); // Horizontal GRAM Start Address
__ili9325_write_reg(0x0051, 239); // Horizontal GRAM End Address
__ili9325_write_reg(0x0052, 0x0000); // Vertical GRAM Start Address
__ili9325_write_reg(0x0053, 319); // Vertical GRAM Start Address
__ili9325_write_reg(0x0060, 0x2700); // GS=0 320 line
__ili9325_write_reg(0x0061, 0x0001); // NDL,VLE（滚屏允许）, REV（灰度翻转）
__ili9325_write_reg(0x006a, 0x0000); // set scrolling line
// -------------- Partial Display Control ---------
__ili9325_write_reg(0x0080, 0x0000);
__ili9325_write_reg(0x0081, 0x0000);
__ili9325_write_reg(0x0082, 0x0000);
__ili9325_write_reg(0x0083, 0x0000);
__ili9325_write_reg(0x0084, 0x0000);
__ili9325_write_reg(0x0085, 0x0000);
// -------------- Panel Control -------------------
__ili9325_write_reg(0x0090, 0x0010);
__ili9325_write_reg(0x0092, 0x0000);
__ili9325_write_reg(0x0093, 0x0003);
__ili9325_write_reg(0x0095, 0x0110);
__ili9325_write_reg(0x0097, 0x0000);
__ili9325_write_reg(0x0098, 0x0000);
// Set GRAM write direction and BGR = 1
// I/D=11 (Horizontal : increment, Vertical : increment)
// AM=0 (address is updated in Horizontal writing direction)
__ili9325_write_reg(0x0003, 0x1030);
__ili9325_write_reg(0x0007, 0x0173); // 262K color and display ON
lcd_backlight_on();
}
int main(void) {
int c;
char buff[100];
int offset = 0;
int started = 0;
//ctc_clocksInit(12000000,60000000,1);
//ctc_mamInit(MAM_FULLY_ENABLED);
//ramvectorsInit();
//busywaitInit();
VPBDIV = 0x00000001; /* PCLK = CCLK */
PLLCFG = 0x00000024; /* Fosc=12MHz, CCLK=60MHz */
PLLCON = 0x00000001; /* enable the PLL */
PLLFEED = 0x000000AA; /* feed sequence */
PLLFEED = 0x00000055;
while (!(PLLSTAT & 0x00000400));
PLLCON = 3; // enable and connect
PLLFEED = 0xAA;
PLLFEED = 0x55;
vicInit();
uart0Init();
DBG("Initializing USB stack\n");
usbInit();
vcomInit();
DBG("Starting USB communication\n");
interruptsEnable();
usbConnect();
lcdInit();
// echo any character received (do USB stuff in interrupt)
while (1) {
c = vcomGetchar();
if (c != -1) {
// show on console
if ((c == 9) || (c == 10) || (c == 13) || ((c >= 32) && (c <= 126))) {
uint8_t buf[2];
buf[0] = c; buf[1] = 0;
DBG((char*) buf);
} else {
DBG(".");
}
vcomPutchar(c);
if (c == 13) {
DBG("Cmd entered.\n");
buff[offset] = '\0';
offset = 0;
if (!strcmp(buff, "start"))
{
started = 1;
}
else if (started) {
if (!strcmp(buff, "bl-on"))
{
lcd_backlight_on();
}
else if (!strcmp(buff, "bl-off"))
{
lcd_backlight_off();
}
else if (!strcmp(buff, "clear"))
{
lcdClear();
}
else {
lcdPrintString(buff);
}
}
}
else {
buff[offset++] = c;
}
}
}
}