int xway_nand_probe(struct platform_device *pdev)
{
// ltq_gpio_request(PIN_CS1, 1, 0, 1, "NAND_CS1");
ltq_gpio_request(PIN_CLE, 1, 0, 1, "NAND_CLE");
ltq_gpio_request(PIN_ALE, 1, 0, 1, "NAND_ALE");
if (ltq_is_ar9() || ltq_is_vr9()) {
ltq_gpio_request(PIN_RDY, 1, 0, 0, "NAND_BSY");
ltq_gpio_request(PIN_RD, 1, 0, 1, "NAND_RD");
}
ltq_ebu_w32((NAND_BASE_ADDRESS & 0x1fffff00)
| ADDSEL1_MASK(3) | ADDSEL1_REGEN, LTQ_EBU_ADDSEL1);
ltq_ebu_w32(BUSCON1_SETUP | BUSCON1_BCGEN_RES | BUSCON1_WAITWRC2
| BUSCON1_WAITRDC2 | BUSCON1_HOLDC1 | BUSCON1_RECOVC1
| BUSCON1_CMULT4, LTQ_EBU_BUSCON1);
ltq_ebu_w32(NAND_CON_NANDM | NAND_CON_CSMUX | NAND_CON_CS_P
| NAND_CON_SE_P | NAND_CON_WP_P | NAND_CON_PRE_P
| NAND_CON_IN_CS0 | NAND_CON_OUT_CS0, LTQ_EBU_NAND_CON);
ltq_w32(NAND_WRITE_CMD_RESET, ((u32*)(NAND_BASE_ADDRESS | NAND_WRITE_CMD)));
while((ltq_ebu_r32(LTQ_EBU_NAND_WAIT) & NAND_WAIT_WR_C) == 0);
return 0;
}
static void ltq_ebu_apply(void)
{
unsigned long flags;
spin_lock_irqsave(&ebu_lock, flags);
ltq_ebu_w32(LTQ_EBU_BUSCON, LTQ_EBU_BUSCON1);
*((__u16 *)ltq_ebu_gpio_membase) = ltq_ebu_gpio_shadow;
ltq_ebu_w32(LTQ_EBU_BUSCON | LTQ_EBU_WP, LTQ_EBU_BUSCON1);
spin_unlock_irqrestore(&ebu_lock, flags);
}
/**
* ltq_mm_apply() - write the shadow value to the ebu address.
* @chip: Pointer to our private data structure.
*
* Write the shadow value to the EBU to set the gpios. We need to set the
* global EBU lock to make sure that PCI/MTD dont break.
*/
static void ltq_mm_apply(struct ltq_mm *chip)
{
unsigned long flags;
spin_lock_irqsave(&ebu_lock, flags);
ltq_ebu_w32(LTQ_EBU_BUSCON, LTQ_EBU_BUSCON1);
__raw_writew(chip->shadow, chip->mmchip.regs);
ltq_ebu_w32(LTQ_EBU_BUSCON | LTQ_EBU_WP, LTQ_EBU_BUSCON1);
spin_unlock_irqrestore(&ebu_lock, flags);
}
/**
* ltq_mm_save_regs() - Set initial values of GPIO pins
* @mm_gc: pointer to memory mapped GPIO chip structure
*/
static void ltq_mm_save_regs(struct of_mm_gpio_chip *mm_gc)
{
struct ltq_mm *chip =
container_of(mm_gc, struct ltq_mm, mmchip);
/* tell the ebu controller which memory address we will be using */
ltq_ebu_w32(CPHYSADDR(chip->mmchip.regs) | 0x1, LTQ_EBU_ADDRSEL1);
ltq_mm_apply(chip);
}
static int ltq_ebu_probe(struct platform_device *pdev)
{
int ret = 0;
struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev, "failed to get memory resource\n");
return -ENOENT;
}
res = devm_request_mem_region(&pdev->dev, res->start,
resource_size(res), dev_name(&pdev->dev));
if (!res) {
dev_err(&pdev->dev, "failed to request memory resource\n");
return -EBUSY;
}
ltq_ebu_gpio_membase = devm_ioremap_nocache(&pdev->dev, res->start,
resource_size(res));
if (!ltq_ebu_gpio_membase) {
dev_err(&pdev->dev, "Failed to ioremap mem region\n");
return -ENOMEM;
}
/* grab the default shadow value passed form the platform code */
ltq_ebu_gpio_shadow = (unsigned int) pdev->dev.platform_data;
/* tell the ebu controller which memory address we will be using */
ltq_ebu_w32(pdev->resource->start | 0x1, LTQ_EBU_ADDRSEL1);
/* write protect the region */
ltq_ebu_w32(LTQ_EBU_BUSCON | LTQ_EBU_WP, LTQ_EBU_BUSCON1);
ret = gpiochip_add(<q_ebu_chip);
if (!ret)
ltq_ebu_apply();
return ret;
}
static void ltq_hw_irqdispatch(int module)
{
u32 irq;
irq = ltq_icu_r32(LTQ_ICU_IM0_IOSR + (module * LTQ_ICU_OFFSET));
if (irq == 0)
return;
irq = __fls(irq);
do_IRQ((int)irq + INT_NUM_IM0_IRL0 + (INT_NUM_IM_OFFSET * module));
if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0))
ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_PCC_ISTAT) | 0x10,
LTQ_EBU_PCC_ISTAT);
}
static void ltq_hw_irqdispatch(int module)
{
u32 irq;
irq = ltq_icu_r32(LTQ_ICU_IM0_IOSR + (module * LTQ_ICU_OFFSET));
if (irq == 0)
return;
/* silicon bug causes only the msb set to 1 to be valid. all
* other bits might be bogus
*/
irq = __fls(irq);
do_IRQ((int)irq + INT_NUM_IM0_IRL0 + (INT_NUM_IM_OFFSET * module));
/* if this is a EBU irq, we need to ack it or get a deadlock */
if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0))
ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_PCC_ISTAT) | 0x10,
LTQ_EBU_PCC_ISTAT);
}
static int __init lantiq_ebu_init(void)
{
/* */
if (insert_resource(&iomem_resource, <q_ebu_resource) < 0)
panic("Failed to insert ebu memory");
if (request_mem_region(ltq_ebu_resource.start,
resource_size(<q_ebu_resource), "ebu") < 0)
panic("Failed to request ebu memory");
/* */
ltq_ebu_membase = ioremap_nocache(ltq_ebu_resource.start,
resource_size(<q_ebu_resource));
if (!ltq_ebu_membase)
panic("Failed to remap ebu memory");
/* */
ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_BUSCON0) & ~EBU_WRDIS, LTQ_EBU_BUSCON0);
return 0;
}
/* bring up all register ranges that we need for basic system control */
void __init ltq_soc_init(void)
{
struct resource res_pmu, res_cgu, res_ebu;
struct device_node *np_pmu =
of_find_compatible_node(NULL, NULL, "lantiq,pmu-xway");
struct device_node *np_cgu =
of_find_compatible_node(NULL, NULL, "lantiq,cgu-xway");
struct device_node *np_ebu =
of_find_compatible_node(NULL, NULL, "lantiq,ebu-xway");
/* check if all the core register ranges are available */
if (!np_pmu || !np_cgu || !np_ebu)
panic("Failed to load core nodess from devicetree");
if (of_address_to_resource(np_pmu, 0, &res_pmu) ||
of_address_to_resource(np_cgu, 0, &res_cgu) ||
of_address_to_resource(np_ebu, 0, &res_ebu))
panic("Failed to get core resources");
if ((request_mem_region(res_pmu.start, resource_size(&res_pmu),
res_pmu.name) < 0) ||
(request_mem_region(res_cgu.start, resource_size(&res_cgu),
res_cgu.name) < 0) ||
(request_mem_region(res_ebu.start, resource_size(&res_ebu),
res_ebu.name) < 0))
pr_err("Failed to request core reources");
pmu_membase = ioremap_nocache(res_pmu.start, resource_size(&res_pmu));
ltq_cgu_membase = ioremap_nocache(res_cgu.start,
resource_size(&res_cgu));
ltq_ebu_membase = ioremap_nocache(res_ebu.start,
resource_size(&res_ebu));
if (!pmu_membase || !ltq_cgu_membase || !ltq_ebu_membase)
panic("Failed to remap core resources");
/* make sure to unprotect the memory region where flash is located */
ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_BUSCON0) & ~EBU_WRDIS, LTQ_EBU_BUSCON0);
/* add our generic xway clocks */
clkdev_add_pmu("10000000.fpi", NULL, 0, PMU_FPI);
clkdev_add_pmu("1e100400.serial", NULL, 0, PMU_ASC0);
clkdev_add_pmu("1e100a00.gptu", NULL, 0, PMU_GPT);
clkdev_add_pmu("1e100bb0.stp", NULL, 0, PMU_STP);
clkdev_add_pmu("1e104100.dma", NULL, 0, PMU_DMA);
clkdev_add_pmu("1e100800.spi", NULL, 0, PMU_SPI);
clkdev_add_pmu("1e105300.ebu", NULL, 0, PMU_EBU);
clkdev_add_clkout();
/* add the soc dependent clocks */
if (of_machine_is_compatible("lantiq,vr9")) {
ifccr = CGU_IFCCR_VR9;
pcicr = CGU_PCICR_VR9;
} else {
clkdev_add_pmu("1e180000.etop", NULL, 0, PMU_PPE);
}
if (!of_machine_is_compatible("lantiq,ase")) {
clkdev_add_pmu("1e100c00.serial", NULL, 0, PMU_ASC1);
clkdev_add_pci();
}
if (of_machine_is_compatible("lantiq,ase")) {
if (ltq_cgu_r32(CGU_SYS) & (1 << 5))
clkdev_add_static(CLOCK_266M, CLOCK_133M, CLOCK_133M);
else
clkdev_add_static(CLOCK_133M, CLOCK_133M, CLOCK_133M);
clkdev_add_cgu("1e180000.etop", "ephycgu", CGU_EPHY),
clkdev_add_pmu("1e180000.etop", "ephy", 0, PMU_EPHY);
} else if (of_machine_is_compatible("lantiq,vr9")) {
clkdev_add_static(ltq_vr9_cpu_hz(), ltq_vr9_fpi_hz(),
ltq_vr9_fpi_hz());
clkdev_add_pmu("1d900000.pcie", "phy", 1, PMU1_PCIE_PHY);
clkdev_add_pmu("1d900000.pcie", "bus", 0, PMU_PCIE_CLK);
clkdev_add_pmu("1d900000.pcie", "msi", 1, PMU1_PCIE_MSI);
clkdev_add_pmu("1d900000.pcie", "pdi", 1, PMU1_PCIE_PDI);
clkdev_add_pmu("1d900000.pcie", "ctl", 1, PMU1_PCIE_CTL);
clkdev_add_pmu("1d900000.pcie", "ahb", 0, PMU_AHBM | PMU_AHBS);
} else if (of_machine_is_compatible("lantiq,ar9")) {
clkdev_add_static(ltq_ar9_cpu_hz(), ltq_ar9_fpi_hz(),
ltq_ar9_fpi_hz());
clkdev_add_pmu("1e180000.etop", "switch", 0, PMU_SWITCH);
} else {
clkdev_add_static(ltq_danube_cpu_hz(), ltq_danube_fpi_hz(),
ltq_danube_fpi_hz());
}
}
static int ltq_pci_startup(struct platform_device *pdev)
{
struct device_node *node = pdev->dev.of_node;
const __be32 *req_mask, *bus_clk;
u32 temp_buffer;
/* get our clocks */
clk_pci = clk_get(&pdev->dev, NULL);
if (IS_ERR(clk_pci)) {
dev_err(&pdev->dev, "failed to get pci clock\n");
return PTR_ERR(clk_pci);
}
clk_external = clk_get(&pdev->dev, "external");
if (IS_ERR(clk_external)) {
clk_put(clk_pci);
dev_err(&pdev->dev, "failed to get external pci clock\n");
return PTR_ERR(clk_external);
}
/* read the bus speed that we want */
bus_clk = of_get_property(node, "lantiq,bus-clock", NULL);
if (bus_clk)
clk_set_rate(clk_pci, *bus_clk);
/* and enable the clocks */
clk_enable(clk_pci);
if (of_find_property(node, "lantiq,external-clock", NULL))
clk_enable(clk_external);
else
clk_disable(clk_external);
/* setup reset gpio used by pci */
reset_gpio = of_get_named_gpio(node, "gpio-reset", 0);
if (gpio_is_valid(reset_gpio)) {
int ret = devm_gpio_request(&pdev->dev,
reset_gpio, "pci-reset");
if (ret) {
dev_err(&pdev->dev,
"failed to request gpio %d\n", reset_gpio);
return ret;
}
gpio_direction_output(reset_gpio, 1);
}
/* enable auto-switching between PCI and EBU */
ltq_pci_w32(0xa, PCI_CR_CLK_CTRL);
/* busy, i.e. configuration is not done, PCI access has to be retried */
ltq_pci_w32(ltq_pci_r32(PCI_CR_PCI_MOD) & ~(1 << 24), PCI_CR_PCI_MOD);
wmb();
/* BUS Master/IO/MEM access */
ltq_pci_cfg_w32(ltq_pci_cfg_r32(PCI_CS_STS_CMD) | 7, PCI_CS_STS_CMD);
/* enable external 2 PCI masters */
temp_buffer = ltq_pci_r32(PCI_CR_PC_ARB);
/* setup the request mask */
req_mask = of_get_property(node, "req-mask", NULL);
if (req_mask)
temp_buffer &= ~((*req_mask & 0xf) << 16);
else
temp_buffer &= ~0xf0000;
/* enable internal arbiter */
temp_buffer |= (1 << INTERNAL_ARB_ENABLE_BIT);
/* enable internal PCI master reqest */
temp_buffer &= (~(3 << PCI_MASTER0_REQ_MASK_2BITS));
/* enable EBU request */
temp_buffer &= (~(3 << PCI_MASTER1_REQ_MASK_2BITS));
/* enable all external masters request */
temp_buffer &= (~(3 << PCI_MASTER2_REQ_MASK_2BITS));
ltq_pci_w32(temp_buffer, PCI_CR_PC_ARB);
wmb();
/* setup BAR memory regions */
ltq_pci_w32(0x18000000, PCI_CR_FCI_ADDR_MAP0);
ltq_pci_w32(0x18400000, PCI_CR_FCI_ADDR_MAP1);
ltq_pci_w32(0x18800000, PCI_CR_FCI_ADDR_MAP2);
ltq_pci_w32(0x18c00000, PCI_CR_FCI_ADDR_MAP3);
ltq_pci_w32(0x19000000, PCI_CR_FCI_ADDR_MAP4);
ltq_pci_w32(0x19400000, PCI_CR_FCI_ADDR_MAP5);
ltq_pci_w32(0x19800000, PCI_CR_FCI_ADDR_MAP6);
ltq_pci_w32(0x19c00000, PCI_CR_FCI_ADDR_MAP7);
ltq_pci_w32(0x1ae00000, PCI_CR_FCI_ADDR_MAP11hg);
ltq_pci_w32(ltq_calc_bar11mask(), PCI_CR_BAR11MASK);
ltq_pci_w32(0, PCI_CR_PCI_ADDR_MAP11);
ltq_pci_w32(0, PCI_CS_BASE_ADDR1);
/* both TX and RX endian swap are enabled */
ltq_pci_w32(ltq_pci_r32(PCI_CR_PCI_EOI) | 3, PCI_CR_PCI_EOI);
wmb();
ltq_pci_w32(ltq_pci_r32(PCI_CR_BAR12MASK) | 0x80000000,
PCI_CR_BAR12MASK);
ltq_pci_w32(ltq_pci_r32(PCI_CR_BAR13MASK) | 0x80000000,
PCI_CR_BAR13MASK);
/*use 8 dw burst length */
ltq_pci_w32(0x303, PCI_CR_FCI_BURST_LENGTH);
ltq_pci_w32(ltq_pci_r32(PCI_CR_PCI_MOD) | (1 << 24), PCI_CR_PCI_MOD);
wmb();
/* setup irq line */
ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_PCC_CON) | 0xc, LTQ_EBU_PCC_CON);
ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_PCC_IEN) | 0x10, LTQ_EBU_PCC_IEN);
/* toggle reset pin */
if (gpio_is_valid(reset_gpio)) {
__gpio_set_value(reset_gpio, 0);
wmb();
mdelay(1);
__gpio_set_value(reset_gpio, 1);
}
return 0;
}
/* bring up all register ranges that we need for basic system control */
void __init ltq_soc_init(void)
{
struct resource res_pmu, res_cgu, res_ebu;
struct device_node *np_pmu =
of_find_compatible_node(NULL, NULL, "lantiq,pmu-xway");
struct device_node *np_cgu =
of_find_compatible_node(NULL, NULL, "lantiq,cgu-xway");
struct device_node *np_ebu =
of_find_compatible_node(NULL, NULL, "lantiq,ebu-xway");
/* check if all the core register ranges are available */
if (!np_pmu || !np_cgu || !np_ebu)
panic("Failed to load core nodes from devicetree");
if (of_address_to_resource(np_pmu, 0, &res_pmu) ||
of_address_to_resource(np_cgu, 0, &res_cgu) ||
of_address_to_resource(np_ebu, 0, &res_ebu))
panic("Failed to get core resources");
if (!request_mem_region(res_pmu.start, resource_size(&res_pmu),
res_pmu.name) ||
!request_mem_region(res_cgu.start, resource_size(&res_cgu),
res_cgu.name) ||
!request_mem_region(res_ebu.start, resource_size(&res_ebu),
res_ebu.name))
pr_err("Failed to request core resources");
pmu_membase = ioremap_nocache(res_pmu.start, resource_size(&res_pmu));
ltq_cgu_membase = ioremap_nocache(res_cgu.start,
resource_size(&res_cgu));
ltq_ebu_membase = ioremap_nocache(res_ebu.start,
resource_size(&res_ebu));
if (!pmu_membase || !ltq_cgu_membase || !ltq_ebu_membase)
panic("Failed to remap core resources");
if (of_machine_is_compatible("lantiq,vr9")) {
struct resource res_xbar;
struct device_node *np_xbar =
of_find_compatible_node(NULL, NULL,
"lantiq,xbar-xway");
if (!np_xbar)
panic("Failed to load xbar nodes from devicetree");
if (of_address_to_resource(np_xbar, 0, &res_xbar))
panic("Failed to get xbar resources");
if (!request_mem_region(res_xbar.start, resource_size(&res_xbar),
res_xbar.name))
panic("Failed to get xbar resources");
ltq_xbar_membase = ioremap_nocache(res_xbar.start,
resource_size(&res_xbar));
if (!ltq_xbar_membase)
panic("Failed to remap xbar resources");
}
/* make sure to unprotect the memory region where flash is located */
ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_BUSCON0) & ~EBU_WRDIS, LTQ_EBU_BUSCON0);
/* add our generic xway clocks */
clkdev_add_pmu("10000000.fpi", NULL, 0, 0, PMU_FPI);
clkdev_add_pmu("1e100400.serial", NULL, 0, 0, PMU_ASC0);
clkdev_add_pmu("1e100a00.gptu", NULL, 1, 0, PMU_GPT);
clkdev_add_pmu("1e100bb0.stp", NULL, 1, 0, PMU_STP);
clkdev_add_pmu("1e104100.dma", NULL, 1, 0, PMU_DMA);
clkdev_add_pmu("1e100800.spi", NULL, 1, 0, PMU_SPI);
clkdev_add_pmu("1e105300.ebu", NULL, 0, 0, PMU_EBU);
clkdev_add_clkout();
/* add the soc dependent clocks */
if (of_machine_is_compatible("lantiq,vr9")) {
ifccr = CGU_IFCCR_VR9;
pcicr = CGU_PCICR_VR9;
} else {
clkdev_add_pmu("1e180000.etop", NULL, 1, 0, PMU_PPE);
}
if (!of_machine_is_compatible("lantiq,ase")) {
clkdev_add_pmu("1e100c00.serial", NULL, 0, 0, PMU_ASC1);
clkdev_add_pci();
}
if (of_machine_is_compatible("lantiq,grx390") ||
of_machine_is_compatible("lantiq,ar10")) {
clkdev_add_pmu("1e101000.usb", "phy", 1, 2, PMU_ANALOG_USB0_P);
clkdev_add_pmu("1e106000.usb", "phy", 1, 2, PMU_ANALOG_USB1_P);
/* rc 0 */
clkdev_add_pmu("1d900000.pcie", "phy", 1, 2, PMU_ANALOG_PCIE0_P);
clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI);
clkdev_add_pmu("1d900000.pcie", "pdi", 1, 1, PMU1_PCIE_PDI);
clkdev_add_pmu("1d900000.pcie", "ctl", 1, 1, PMU1_PCIE_CTL);
/* rc 1 */
clkdev_add_pmu("19000000.pcie", "phy", 1, 2, PMU_ANALOG_PCIE1_P);
clkdev_add_pmu("19000000.pcie", "msi", 1, 1, PMU1_PCIE1_MSI);
clkdev_add_pmu("19000000.pcie", "pdi", 1, 1, PMU1_PCIE1_PDI);
clkdev_add_pmu("19000000.pcie", "ctl", 1, 1, PMU1_PCIE1_CTL);
}
if (of_machine_is_compatible("lantiq,ase")) {
if (ltq_cgu_r32(CGU_SYS) & (1 << 5))
clkdev_add_static(CLOCK_266M, CLOCK_133M,
CLOCK_133M, CLOCK_266M);
else
clkdev_add_static(CLOCK_133M, CLOCK_133M,
CLOCK_133M, CLOCK_133M);
clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0);
clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P);
clkdev_add_pmu("1e180000.etop", "ppe", 1, 0, PMU_PPE);
clkdev_add_cgu("1e180000.etop", "ephycgu", CGU_EPHY);
clkdev_add_pmu("1e180000.etop", "ephy", 1, 0, PMU_EPHY);
clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_ASE_SDIO);
clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
} else if (of_machine_is_compatible("lantiq,grx390")) {
clkdev_add_static(ltq_grx390_cpu_hz(), ltq_grx390_fpi_hz(),
ltq_grx390_fpi_hz(), ltq_grx390_pp32_hz());
clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0);
clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1);
/* rc 2 */
clkdev_add_pmu("1a800000.pcie", "phy", 1, 2, PMU_ANALOG_PCIE2_P);
clkdev_add_pmu("1a800000.pcie", "msi", 1, 1, PMU1_PCIE2_MSI);
clkdev_add_pmu("1a800000.pcie", "pdi", 1, 1, PMU1_PCIE2_PDI);
clkdev_add_pmu("1a800000.pcie", "ctl", 1, 1, PMU1_PCIE2_CTL);
clkdev_add_pmu("1e108000.eth", NULL, 0, 0, PMU_SWITCH | PMU_PPE_DP);
clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
} else if (of_machine_is_compatible("lantiq,ar10")) {
clkdev_add_static(ltq_ar10_cpu_hz(), ltq_ar10_fpi_hz(),
ltq_ar10_fpi_hz(), ltq_ar10_pp32_hz());
clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0);
clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1);
clkdev_add_pmu("1e108000.eth", NULL, 0, 0, PMU_SWITCH |
PMU_PPE_DP | PMU_PPE_TC);
clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
clkdev_add_pmu("1f203000.rcu", "gphy", 1, 0, PMU_GPHY);
clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
clkdev_add_pmu("1e116000.mei", "afe", 1, 2, PMU_ANALOG_DSL_AFE);
clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
} else if (of_machine_is_compatible("lantiq,vr9")) {
clkdev_add_static(ltq_vr9_cpu_hz(), ltq_vr9_fpi_hz(),
ltq_vr9_fpi_hz(), ltq_vr9_pp32_hz());
clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P);
clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0 | PMU_AHBM);
clkdev_add_pmu("1e106000.usb", "phy", 1, 0, PMU_USB1_P);
clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1 | PMU_AHBM);
clkdev_add_pmu("1d900000.pcie", "phy", 1, 1, PMU1_PCIE_PHY);
clkdev_add_pmu("1d900000.pcie", "bus", 1, 0, PMU_PCIE_CLK);
clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI);
clkdev_add_pmu("1d900000.pcie", "pdi", 1, 1, PMU1_PCIE_PDI);
clkdev_add_pmu("1d900000.pcie", "ctl", 1, 1, PMU1_PCIE_CTL);
clkdev_add_pmu(NULL, "ahb", 1, 0, PMU_AHBM | PMU_AHBS);
clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
clkdev_add_pmu("1e108000.eth", NULL, 0, 0,
PMU_SWITCH | PMU_PPE_DPLUS | PMU_PPE_DPLUM |
PMU_PPE_EMA | PMU_PPE_TC | PMU_PPE_SLL01 |
PMU_PPE_QSB | PMU_PPE_TOP);
clkdev_add_pmu("1f203000.rcu", "gphy", 0, 0, PMU_GPHY);
clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO);
clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
} else if (of_machine_is_compatible("lantiq,ar9")) {
clkdev_add_static(ltq_ar9_cpu_hz(), ltq_ar9_fpi_hz(),
ltq_ar9_fpi_hz(), CLOCK_250M);
clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0);
clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P);
clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1);
clkdev_add_pmu("1e106000.usb", "phy", 1, 0, PMU_USB1_P);
clkdev_add_pmu("1e180000.etop", "switch", 1, 0, PMU_SWITCH);
clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO);
clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
clkdev_add_pmu("1e100400.serial", NULL, 1, 0, PMU_ASC0);
} else {
clkdev_add_static(ltq_danube_cpu_hz(), ltq_danube_fpi_hz(),
ltq_danube_fpi_hz(), ltq_danube_pp32_hz());
clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0);
clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P);
clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO);
clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
clkdev_add_pmu("1e100400.serial", NULL, 1, 0, PMU_ASC0);
}
if (of_machine_is_compatible("lantiq,vr9"))
xbar_fpi_burst_disable();
}
/*
* Probe for the NAND device.
*/
static int xway_nand_probe(struct platform_device *pdev)
{
struct xway_nand_data *data;
struct mtd_info *mtd;
struct resource *res;
int err;
u32 cs;
u32 cs_flag = 0;
/* Allocate memory for the device structure (and zero it) */
data = devm_kzalloc(&pdev->dev, sizeof(struct xway_nand_data),
GFP_KERNEL);
if (!data)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
data->nandaddr = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(data->nandaddr))
return PTR_ERR(data->nandaddr);
nand_set_flash_node(&data->chip, pdev->dev.of_node);
mtd = nand_to_mtd(&data->chip);
mtd->dev.parent = &pdev->dev;
data->chip.cmd_ctrl = xway_cmd_ctrl;
data->chip.dev_ready = xway_dev_ready;
data->chip.select_chip = xway_select_chip;
data->chip.write_buf = xway_write_buf;
data->chip.read_buf = xway_read_buf;
data->chip.read_byte = xway_read_byte;
data->chip.chip_delay = 30;
data->chip.ecc.mode = NAND_ECC_SOFT;
data->chip.ecc.algo = NAND_ECC_HAMMING;
platform_set_drvdata(pdev, data);
nand_set_controller_data(&data->chip, data);
/* load our CS from the DT. Either we find a valid 1 or default to 0 */
err = of_property_read_u32(pdev->dev.of_node, "lantiq,cs", &cs);
if (!err && cs == 1)
cs_flag = NAND_CON_IN_CS1 | NAND_CON_OUT_CS1;
/* setup the EBU to run in NAND mode on our base addr */
ltq_ebu_w32(CPHYSADDR(data->nandaddr)
| ADDSEL1_MASK(3) | ADDSEL1_REGEN, EBU_ADDSEL1);
ltq_ebu_w32(BUSCON1_SETUP | BUSCON1_BCGEN_RES | BUSCON1_WAITWRC2
| BUSCON1_WAITRDC2 | BUSCON1_HOLDC1 | BUSCON1_RECOVC1
| BUSCON1_CMULT4, LTQ_EBU_BUSCON1);
ltq_ebu_w32(NAND_CON_NANDM | NAND_CON_CSMUX | NAND_CON_CS_P
| NAND_CON_SE_P | NAND_CON_WP_P | NAND_CON_PRE_P
| cs_flag, EBU_NAND_CON);
/* Scan to find existence of the device */
err = nand_scan(mtd, 1);
if (err)
return err;
err = mtd_device_register(mtd, NULL, 0);
if (err)
nand_release(mtd);
return err;
}
