static int mei_txe_write(struct mei_device *dev,
struct mei_msg_hdr *header,
const unsigned char *buf)
{
struct mei_txe_hw *hw = to_txe_hw(dev);
unsigned long rem;
unsigned long length;
int slots = dev->hbuf_depth;
u32 *reg_buf = (u32 *)buf;
u32 dw_cnt;
int i;
if (WARN_ON(!header || !buf))
return -EINVAL;
length = header->length;
dev_dbg(dev->dev, MEI_HDR_FMT, MEI_HDR_PRM(header));
dw_cnt = mei_data2slots(length);
if (dw_cnt > slots)
return -EMSGSIZE;
if (WARN(!hw->aliveness, "txe write: aliveness not asserted\n"))
return -EAGAIN;
/* Enable Input Ready Interrupt. */
mei_txe_input_ready_interrupt_enable(dev);
if (!mei_txe_is_input_ready(dev)) {
char fw_sts_str[MEI_FW_STATUS_STR_SZ];
mei_fw_status_str(dev, fw_sts_str, MEI_FW_STATUS_STR_SZ);
dev_err(dev->dev, "Input is not ready %s\n", fw_sts_str);
return -EAGAIN;
}
mei_txe_input_payload_write(dev, 0, *((u32 *)header));
for (i = 0; i < length / 4; i++)
mei_txe_input_payload_write(dev, i + 1, reg_buf[i]);
rem = length & 0x3;
if (rem > 0) {
u32 reg = 0;
memcpy(®, &buf[length - rem], rem);
mei_txe_input_payload_write(dev, i + 1, reg);
}
/* after each write the whole buffer is consumed */
hw->slots = 0;
/* Set Input-Doorbell */
mei_txe_input_doorbell_set(hw);
return 0;
}
/**
* mei_reset - resets host and fw.
*
* @dev: the device structure
*
* Return: 0 on success or < 0 if the reset hasn't succeeded
*/
int mei_reset(struct mei_device *dev)
{
enum mei_dev_state state = dev->dev_state;
bool interrupts_enabled;
int ret;
if (state != MEI_DEV_INITIALIZING &&
state != MEI_DEV_DISABLED &&
state != MEI_DEV_POWER_DOWN &&
state != MEI_DEV_POWER_UP) {
char fw_sts_str[MEI_FW_STATUS_STR_SZ];
mei_fw_status_str(dev, fw_sts_str, MEI_FW_STATUS_STR_SZ);
dev_warn(dev->dev, "unexpected reset: dev_state = %s fw status = %s\n",
mei_dev_state_str(state), fw_sts_str);
}
mei_clear_interrupts(dev);
/* we're already in reset, cancel the init timer
* if the reset was called due the hbm protocol error
* we need to call it before hw start
* so the hbm watchdog won't kick in
*/
mei_hbm_idle(dev);
/* enter reset flow */
interrupts_enabled = state != MEI_DEV_POWER_DOWN;
dev->dev_state = MEI_DEV_RESETTING;
dev->reset_count++;
if (dev->reset_count > MEI_MAX_CONSEC_RESET) {
dev_err(dev->dev, "reset: reached maximal consecutive resets: disabling the device\n");
dev->dev_state = MEI_DEV_DISABLED;
return -ENODEV;
}
ret = mei_hw_reset(dev, interrupts_enabled);
/* fall through and remove the sw state even if hw reset has failed */
/* no need to clean up software state in case of power up */
if (state != MEI_DEV_INITIALIZING && state != MEI_DEV_POWER_UP)
mei_cl_all_disconnect(dev);
mei_hbm_reset(dev);
memset(dev->rd_msg_hdr, 0, sizeof(dev->rd_msg_hdr));
if (ret) {
dev_err(dev->dev, "hw_reset failed ret = %d\n", ret);
return ret;
}
if (state == MEI_DEV_POWER_DOWN) {
dev_dbg(dev->dev, "powering down: end of reset\n");
dev->dev_state = MEI_DEV_DISABLED;
return 0;
}
ret = mei_hw_start(dev);
if (ret) {
dev_err(dev->dev, "hw_start failed ret = %d\n", ret);
return ret;
}
dev_dbg(dev->dev, "link is established start sending messages.\n");
dev->dev_state = MEI_DEV_INIT_CLIENTS;
ret = mei_hbm_start_req(dev);
if (ret) {
dev_err(dev->dev, "hbm_start failed ret = %d\n", ret);
dev->dev_state = MEI_DEV_RESETTING;
return ret;
}
return 0;
}
