static int reg_fixed_voltage_probe(struct platform_device *pdev)
{
struct fixed_voltage_config *config;
struct fixed_voltage_data *drvdata;
struct regulator_config cfg = { };
int ret;
if (pdev->dev.of_node) {
config = of_get_fixed_voltage_config(&pdev->dev);
if (IS_ERR(config))
return PTR_ERR(config);
} else {
config = dev_get_platdata(&pdev->dev);
}
if (!config)
return -ENOMEM;
drvdata = devm_kzalloc(&pdev->dev, sizeof(struct fixed_voltage_data),
GFP_KERNEL);
if (!drvdata)
return -ENOMEM;
drvdata->desc.name = devm_kstrdup(&pdev->dev,
config->supply_name,
GFP_KERNEL);
if (drvdata->desc.name == NULL) {
dev_err(&pdev->dev, "Failed to allocate supply name\n");
return -ENOMEM;
}
drvdata->desc.type = REGULATOR_VOLTAGE;
drvdata->desc.owner = THIS_MODULE;
drvdata->desc.ops = &fixed_voltage_ops;
drvdata->desc.enable_time = config->startup_delay;
if (config->input_supply) {
drvdata->desc.supply_name = devm_kstrdup(&pdev->dev,
config->input_supply,
GFP_KERNEL);
if (!drvdata->desc.supply_name) {
dev_err(&pdev->dev,
"Failed to allocate input supply\n");
return -ENOMEM;
}
}
if (config->microvolts)
drvdata->desc.n_voltages = 1;
drvdata->desc.fixed_uV = config->microvolts;
if (config->gpio >= 0)
cfg.ena_gpio = config->gpio;
cfg.ena_gpio_invert = !config->enable_high;
if (config->enabled_at_boot) {
if (config->enable_high)
cfg.ena_gpio_flags |= GPIOF_OUT_INIT_HIGH;
else
cfg.ena_gpio_flags |= GPIOF_OUT_INIT_LOW;
} else {
if (config->enable_high)
cfg.ena_gpio_flags |= GPIOF_OUT_INIT_LOW;
else
cfg.ena_gpio_flags |= GPIOF_OUT_INIT_HIGH;
}
if (config->gpio_is_open_drain)
cfg.ena_gpio_flags |= GPIOF_OPEN_DRAIN;
cfg.dev = &pdev->dev;
cfg.init_data = config->init_data;
cfg.driver_data = drvdata;
cfg.of_node = pdev->dev.of_node;
drvdata->dev = devm_regulator_register(&pdev->dev, &drvdata->desc,
&cfg);
if (IS_ERR(drvdata->dev)) {
ret = PTR_ERR(drvdata->dev);
dev_err(&pdev->dev, "Failed to register regulator: %d\n", ret);
return ret;
}
platform_set_drvdata(pdev, drvdata);
dev_dbg(&pdev->dev, "%s supplying %duV\n", drvdata->desc.name,
drvdata->desc.fixed_uV);
return 0;
}
static int __devinit reg_fixed_voltage_probe(struct platform_device *pdev)
{
struct fixed_voltage_config *config;
struct fixed_voltage_data *drvdata;
int ret;
if (pdev->dev.of_node)
config = of_get_fixed_voltage_config(&pdev->dev);
else
config = pdev->dev.platform_data;
if (!config)
return -ENOMEM;
drvdata = kzalloc(sizeof(struct fixed_voltage_data), GFP_KERNEL);
if (drvdata == NULL) {
dev_err(&pdev->dev, "Failed to allocate device data\n");
ret = -ENOMEM;
goto err;
}
drvdata->desc.name = kstrdup(config->supply_name, GFP_KERNEL);
if (drvdata->desc.name == NULL) {
dev_err(&pdev->dev, "Failed to allocate supply name\n");
ret = -ENOMEM;
goto err;
}
drvdata->desc.type = REGULATOR_VOLTAGE;
drvdata->desc.owner = THIS_MODULE;
drvdata->desc.ops = &fixed_voltage_ops;
if (config->microvolts)
drvdata->desc.n_voltages = 1;
drvdata->microvolts = config->microvolts;
drvdata->gpio = config->gpio;
drvdata->startup_delay = config->startup_delay;
if (gpio_is_valid(config->gpio)) {
drvdata->enable_high = config->enable_high;
/* FIXME: Remove below print warning
*
* config->gpio must be set to -EINVAL by platform code if
* GPIO control is not required. However, early adopters
* not requiring GPIO control may forget to initialize
* config->gpio to -EINVAL. This will cause GPIO 0 to be used
* for GPIO control.
*
* This warning will be removed once there are a couple of users
* for this driver.
*/
if (!config->gpio)
dev_warn(&pdev->dev,
"using GPIO 0 for regulator enable control\n");
ret = gpio_request(config->gpio, config->supply_name);
if (ret) {
dev_err(&pdev->dev,
"Could not obtain regulator enable GPIO %d: %d\n",
config->gpio, ret);
goto err_name;
}
/* set output direction without changing state
* to prevent glitch
*/
drvdata->is_enabled = config->enabled_at_boot;
ret = drvdata->is_enabled ?
config->enable_high : !config->enable_high;
ret = gpio_direction_output(config->gpio, ret);
if (ret) {
dev_err(&pdev->dev,
"Could not configure regulator enable GPIO %d direction: %d\n",
config->gpio, ret);
goto err_gpio;
}
} else {
/* Regulator without GPIO control is considered
* always enabled
*/
drvdata->is_enabled = true;
}
drvdata->dev = regulator_register(&drvdata->desc, &pdev->dev,
config->init_data, drvdata);
if (IS_ERR(drvdata->dev)) {
ret = PTR_ERR(drvdata->dev);
dev_err(&pdev->dev, "Failed to register regulator: %d\n", ret);
goto err_gpio;
}
platform_set_drvdata(pdev, drvdata);
dev_dbg(&pdev->dev, "%s supplying %duV\n", drvdata->desc.name,
drvdata->microvolts);
return 0;
err_gpio:
if (gpio_is_valid(config->gpio))
gpio_free(config->gpio);
err_name:
kfree(drvdata->desc.name);
err:
kfree(drvdata);
return ret;
}
