/*
* Note that on Innovator-1510 UART2 pins conflict with USB2.
* By default UART2 does not work on Innovator-1510 if you have
* USB OHCI enabled. To use UART2, you must disable USB2 first.
*/
void __init omap_serial_init(void)
{
int i;
const struct omap_uart_config *info;
if (cpu_is_omap730()) {
serial_platform_data[0].regshift = 0;
serial_platform_data[1].regshift = 0;
serial_platform_data[0].irq = INT_730_UART_MODEM_1;
serial_platform_data[1].irq = INT_730_UART_MODEM_IRDA_2;
}
if (cpu_is_omap1510()) {
serial_platform_data[0].uartclk = OMAP1510_BASE_BAUD * 16;
serial_platform_data[1].uartclk = OMAP1510_BASE_BAUD * 16;
serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16;
}
info = omap_get_config(OMAP_TAG_UART, struct omap_uart_config);
if (info == NULL)
return;
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
unsigned char reg;
if (!((1 << i) & info->enabled_uarts)) {
serial_platform_data[i].membase = NULL;
serial_platform_data[i].mapbase = 0;
continue;
}
switch (i) {
case 0:
uart1_ck = clk_get(NULL, "uart1_ck");
if (IS_ERR(uart1_ck))
printk("Could not get uart1_ck\n");
else {
clk_use(uart1_ck);
if (cpu_is_omap1510())
clk_set_rate(uart1_ck, 12000000);
}
if (cpu_is_omap1510()) {
omap_cfg_reg(UART1_TX);
omap_cfg_reg(UART1_RTS);
if (machine_is_omap_innovator()) {
reg = fpga_read(OMAP1510_FPGA_POWER);
reg |= OMAP1510_FPGA_PCR_COM1_EN;
fpga_write(reg, OMAP1510_FPGA_POWER);
udelay(10);
}
}
break;
case 1:
uart2_ck = clk_get(NULL, "uart2_ck");
if (IS_ERR(uart2_ck))
printk("Could not get uart2_ck\n");
else {
clk_use(uart2_ck);
if (cpu_is_omap1510())
clk_set_rate(uart2_ck, 12000000);
else
clk_set_rate(uart2_ck, 48000000);
}
if (cpu_is_omap1510()) {
omap_cfg_reg(UART2_TX);
omap_cfg_reg(UART2_RTS);
if (machine_is_omap_innovator()) {
reg = fpga_read(OMAP1510_FPGA_POWER);
reg |= OMAP1510_FPGA_PCR_COM2_EN;
fpga_write(reg, OMAP1510_FPGA_POWER);
udelay(10);
}
}
break;
case 2:
uart3_ck = clk_get(NULL, "uart3_ck");
if (IS_ERR(uart3_ck))
printk("Could not get uart3_ck\n");
else {
clk_use(uart3_ck);
if (cpu_is_omap1510())
clk_set_rate(uart3_ck, 12000000);
}
if (cpu_is_omap1510()) {
omap_cfg_reg(UART3_TX);
omap_cfg_reg(UART3_RX);
}
break;
}
omap_serial_reset(&serial_platform_data[i]);
}
}
/*
* Note that on Innovator-1510 UART2 pins conflict with USB2.
* By default UART2 does not work on Innovator-1510 if you have
* USB OHCI enabled. To use UART2, you must disable USB2 first.
*/
void __init omap_serial_init(void)
{
int i;
if (cpu_is_omap730()) {
serial_platform_data[0].regshift = 0;
serial_platform_data[1].regshift = 0;
serial_platform_data[0].irq = INT_730_UART_MODEM_1;
serial_platform_data[1].irq = INT_730_UART_MODEM_IRDA_2;
}
if (cpu_is_omap850()) {
serial_platform_data[0].regshift = 0;
serial_platform_data[1].regshift = 0;
serial_platform_data[0].irq = INT_850_UART_MODEM_1;
serial_platform_data[1].irq = INT_850_UART_MODEM_IRDA_2;
}
if (cpu_is_omap15xx()) {
serial_platform_data[0].uartclk = OMAP1510_BASE_BAUD * 16;
serial_platform_data[1].uartclk = OMAP1510_BASE_BAUD * 16;
serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16;
}
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
switch (i) {
case 0:
uart1_ck = clk_get(NULL, "uart1_ck");
if (IS_ERR(uart1_ck))
printk("Could not get uart1_ck\n");
else {
clk_enable(uart1_ck);
if (cpu_is_omap15xx())
clk_set_rate(uart1_ck, 12000000);
}
break;
case 1:
uart2_ck = clk_get(NULL, "uart2_ck");
if (IS_ERR(uart2_ck))
printk("Could not get uart2_ck\n");
else {
clk_enable(uart2_ck);
if (cpu_is_omap15xx())
clk_set_rate(uart2_ck, 12000000);
else
clk_set_rate(uart2_ck, 48000000);
}
break;
case 2:
uart3_ck = clk_get(NULL, "uart3_ck");
if (IS_ERR(uart3_ck))
printk("Could not get uart3_ck\n");
else {
clk_enable(uart3_ck);
if (cpu_is_omap15xx())
clk_set_rate(uart3_ck, 12000000);
}
break;
}
omap_serial_reset(&serial_platform_data[i]);
}
}
/*
* Note that on Innovator-1510 UART2 pins conflict with USB2.
* By default UART2 does not work on Innovator-1510 if you have
* USB OHCI enabled. To use UART2, you must disable USB2 first.
*/
void __init omap_serial_init(void)
{
int i;
if (cpu_is_omap7xx()) {
serial_platform_data[0].regshift = 0;
serial_platform_data[1].regshift = 0;
serial_platform_data[0].irq = INT_7XX_UART_MODEM_1;
serial_platform_data[1].irq = INT_7XX_UART_MODEM_IRDA_2;
}
if (cpu_is_omap15xx()) {
serial_platform_data[0].uartclk = OMAP1510_BASE_BAUD * 16;
serial_platform_data[1].uartclk = OMAP1510_BASE_BAUD * 16;
serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16;
}
for (i = 0; i < ARRAY_SIZE(serial_platform_data) - 1; i++) {
/* Don't look at UARTs higher than 2 for omap7xx */
if (cpu_is_omap7xx() && i > 1) {
serial_platform_data[i].membase = NULL;
serial_platform_data[i].mapbase = 0;
continue;
}
/* Static mapping, never released */
serial_platform_data[i].membase =
ioremap(serial_platform_data[i].mapbase, SZ_2K);
if (!serial_platform_data[i].membase) {
printk(KERN_ERR "Could not ioremap uart%i\n", i);
continue;
}
switch (i) {
case 0:
uart1_ck = clk_get(NULL, "uart1_ck");
if (IS_ERR(uart1_ck))
printk("Could not get uart1_ck\n");
else {
clk_enable(uart1_ck);
if (cpu_is_omap15xx())
clk_set_rate(uart1_ck, 12000000);
}
break;
case 1:
uart2_ck = clk_get(NULL, "uart2_ck");
if (IS_ERR(uart2_ck))
printk("Could not get uart2_ck\n");
else {
clk_enable(uart2_ck);
if (cpu_is_omap15xx())
clk_set_rate(uart2_ck, 12000000);
else
clk_set_rate(uart2_ck, 48000000);
}
break;
case 2:
uart3_ck = clk_get(NULL, "uart3_ck");
if (IS_ERR(uart3_ck))
printk("Could not get uart3_ck\n");
else {
clk_enable(uart3_ck);
if (cpu_is_omap15xx())
clk_set_rate(uart3_ck, 12000000);
}
break;
}
omap_serial_reset(&serial_platform_data[i]);
}
}
void __init omap_serial_init()
{
int i;
const struct omap_uart_config *info;
/*
* Make sure the serial ports are muxed on at this point.
* You have to mux them off in device drivers later on
* if not needed.
*/
info = omap_get_config(OMAP_TAG_UART,
struct omap_uart_config);
if (info == NULL)
return;
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
struct plat_serial8250_port *p = serial_platform_data + i;
if (!(info->enabled_uarts & (1 << i))) {
p->membase = 0;
p->mapbase = 0;
continue;
}
switch (i) {
case 0:
uart1_ick = clk_get(NULL, "uart1_ick");
if (IS_ERR(uart1_ick))
printk("Could not get uart1_ick\n");
else {
clk_enable(uart1_ick);
}
uart1_fck = clk_get(NULL, "uart1_fck");
if (IS_ERR(uart1_fck))
printk("Could not get uart1_fck\n");
else {
clk_enable(uart1_fck);
}
break;
case 1:
uart2_ick = clk_get(NULL, "uart2_ick");
if (IS_ERR(uart2_ick))
printk("Could not get uart2_ick\n");
else {
clk_enable(uart2_ick);
}
uart2_fck = clk_get(NULL, "uart2_fck");
if (IS_ERR(uart2_fck))
printk("Could not get uart2_fck\n");
else {
clk_enable(uart2_fck);
}
break;
case 2:
uart3_ick = clk_get(NULL, "uart3_ick");
if (IS_ERR(uart3_ick))
printk("Could not get uart3_ick\n");
else {
clk_enable(uart3_ick);
}
uart3_fck = clk_get(NULL, "uart3_fck");
if (IS_ERR(uart3_fck))
printk("Could not get uart3_fck\n");
else {
clk_enable(uart3_fck);
}
break;
}
omap_serial_reset(p);
}
}
