static int __devinit cs5520_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
const struct ide_port_info *d = &cyrix_chipset;
hw_regs_t hw[4], *hws[] = { NULL, NULL, NULL, NULL };
ide_setup_pci_noise(dev, d);
/* We must not grab the entire device, it has 'ISA' space in its
* BARS too and we will freak out other bits of the kernel
*/
if (pci_enable_device_io(dev)) {
printk(KERN_WARNING "%s: Unable to enable 55x0.\n", d->name);
return -ENODEV;
}
pci_set_master(dev);
if (pci_set_dma_mask(dev, DMA_32BIT_MASK)) {
printk(KERN_WARNING "%s: No suitable DMA available.\n",
d->name);
return -ENODEV;
}
/*
* Now the chipset is configured we can let the core
* do all the device setup for us
*/
ide_pci_setup_ports(dev, d, 14, &hw[0], &hws[0]);
return ide_host_add(d, hws, NULL);
}
static int __init cs5535_gpio_probe(struct pci_dev *pdev,
const struct pci_device_id *pci_id)
{
int err;
ulong mask_orig = mask;
/* There are two ways to get the GPIO base address; one is by
* fetching it from MSR_LBAR_GPIO, the other is by reading the
* PCI BAR info. The latter method is easier (especially across
* different architectures), so we'll stick with that for now. If
* it turns out to be unreliable in the face of crappy BIOSes, we
* can always go back to using MSRs.. */
err = pci_enable_device_io(pdev);
if (err) {
dev_err(&pdev->dev, "can't enable device IO\n");
goto done;
}
err = pci_request_region(pdev, GPIO_BAR, DRV_NAME);
if (err) {
dev_err(&pdev->dev, "can't alloc PCI BAR #%d\n", GPIO_BAR);
goto done;
}
/* set up the driver-specific struct */
cs5535_gpio_chip.base = pci_resource_start(pdev, GPIO_BAR);
cs5535_gpio_chip.pdev = pdev;
spin_lock_init(&cs5535_gpio_chip.lock);
dev_info(&pdev->dev, "allocated PCI BAR #%d: base 0x%llx\n", GPIO_BAR,
(unsigned long long) cs5535_gpio_chip.base);
/* mask out reserved pins */
mask &= 0x1F7FFFFF;
/* do not allow pin 28, Power Button, as there's special handling
* in the PMC needed. (note 12, p. 48) */
mask &= ~(1 << 28);
if (mask_orig != mask)
dev_info(&pdev->dev, "mask changed from 0x%08lX to 0x%08lX\n",
mask_orig, mask);
/* finally, register with the generic GPIO API */
err = gpiochip_add(&cs5535_gpio_chip.chip);
if (err)
goto release_region;
dev_info(&pdev->dev, DRV_NAME ": GPIO support successfully loaded.\n");
return 0;
release_region:
pci_release_region(pdev, GPIO_BAR);
done:
return err;
}
static int cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const unsigned int cmd_port[] = { 0x1F0, 0x170 };
static const unsigned int ctl_port[] = { 0x3F6, 0x376 };
struct ata_port_info pi = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.port_ops = &cs5520_port_ops,
};
const struct ata_port_info *ppi[2];
u8 pcicfg;
void __iomem *iomap[5];
struct ata_host *host;
struct ata_ioports *ioaddr;
int i, rc;
rc = pcim_enable_device(pdev);
if (rc)
return rc;
/* IDE port enable bits */
pci_read_config_byte(pdev, 0x60, &pcicfg);
/* Check if the ATA ports are enabled */
if ((pcicfg & 3) == 0)
return -ENODEV;
ppi[0] = ppi[1] = &ata_dummy_port_info;
if (pcicfg & 1)
ppi[0] = π
if (pcicfg & 2)
ppi[1] = π
if ((pcicfg & 0x40) == 0) {
dev_warn(&pdev->dev, "DMA mode disabled. Enabling.\n");
pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
}
pi.mwdma_mask = id->driver_data;
host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
if (!host)
return -ENOMEM;
/* Perform set up for DMA */
if (pci_enable_device_io(pdev)) {
printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
return -ENODEV;
}
if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
return -ENODEV;
}
if (pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32))) {
printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
return -ENODEV;
}
/* Map IO ports and initialize host accordingly */
iomap[0] = devm_ioport_map(&pdev->dev, cmd_port[0], 8);
iomap[1] = devm_ioport_map(&pdev->dev, ctl_port[0], 1);
iomap[2] = devm_ioport_map(&pdev->dev, cmd_port[1], 8);
iomap[3] = devm_ioport_map(&pdev->dev, ctl_port[1], 1);
iomap[4] = pcim_iomap(pdev, 2, 0);
if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4])
return -ENOMEM;
ioaddr = &host->ports[0]->ioaddr;
ioaddr->cmd_addr = iomap[0];
ioaddr->ctl_addr = iomap[1];
ioaddr->altstatus_addr = iomap[1];
ioaddr->bmdma_addr = iomap[4];
ata_sff_std_ports(ioaddr);
ata_port_desc(host->ports[0],
"cmd 0x%x ctl 0x%x", cmd_port[0], ctl_port[0]);
ata_port_pbar_desc(host->ports[0], 4, 0, "bmdma");
ioaddr = &host->ports[1]->ioaddr;
ioaddr->cmd_addr = iomap[2];
ioaddr->ctl_addr = iomap[3];
ioaddr->altstatus_addr = iomap[3];
ioaddr->bmdma_addr = iomap[4] + 8;
ata_sff_std_ports(ioaddr);
ata_port_desc(host->ports[1],
"cmd 0x%x ctl 0x%x", cmd_port[1], ctl_port[1]);
ata_port_pbar_desc(host->ports[1], 4, 8, "bmdma");
/* activate the host */
pci_set_master(pdev);
rc = ata_host_start(host);
if (rc)
return rc;
for (i = 0; i < 2; i++) {
static const int irq[] = { 14, 15 };
struct ata_port *ap = host->ports[i];
if (ata_port_is_dummy(ap))
continue;
rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
ata_bmdma_interrupt, 0, DRV_NAME, host);
if (rc)
return rc;
ata_port_desc(ap, "irq %d", irq[i]);
}
return ata_host_register(host, &cs5520_sht);
}
