void __init edison_init_timer(void)
{
#if 1 //calculate mult and shift for sched_clock
u32 shift,mult;
#endif
#ifdef CONFIG_MSTAR_EDISON_BD_FPGA
GLB_TIMER_FREQ_KHZ= 24*1000 ; // PERIPHCLK = CPU Clock / 2,
// div 2 later,when CONFIG_GENERIC_CLOCKEVENTS
// clock event will handle this value
//clock event will handle this value
#else
GLB_TIMER_FREQ_KHZ=(query_frequency()*1000/2); // PERIPHCLK = CPU Clock / 2
// div 2 later,when CONFIG_GENERIC_CLOCKEVENTS
// clock event will handle this value
#endif
printk("Global Timer Frequency = %d MHz\n",GLB_TIMER_FREQ_KHZ/1000);
printk("CPU Clock Frequency = %d MHz\n",query_frequency());
#ifdef CONFIG_HAVE_SCHED_CLOCK
#if 1 //calculate mult and shift for sched_clock
clocks_calc_mult_shift(&mult, &shift, (u32)(GLB_TIMER_FREQ_KHZ*1000), NSEC_PER_SEC,0);
printk("fre = %d, mult= %u, shift= %u\n",(GLB_TIMER_FREQ_KHZ*1000),mult,shift);
SC_SHIFT=shift;
SC_MULT=mult;
#endif
mstar_sched_clock_init((void __iomem *)(PERI_VIRT+0x200), (unsigned long)(GLB_TIMER_FREQ_KHZ*1000));
#endif
#ifdef CONFIG_GENERIC_CLOCKEVENTS
//mstar_local_timer_init(((void __iomem *)PERI_ADDRESS(PERI_PHYS+0x600))); //private_timer base
edison_clocksource_init(EDISON_BASE_REG_TIMER1_PA);
edison_clockevents_init(INT_WDT_IRQ);
#else
setup_irq(E_FIQ_EXTIMER0 , &edison_timer_irq);
//enable timer interrupt
SETREG16(EDISON_BASE_REG_TIMER0_PA,TIMER_INTERRUPT);
//set interval
interval = ( 12*1000*1000 ) / HZ ;
OUTREG16(EDISON_BASE_REG_TIMER0_PA + ADDR_TIMER_MAX_LOW, (interval & 0xffff));
OUTREG16(EDISON_BASE_REG_TIMER0_PA + ADDR_TIMER_MAX_HIGH, (interval >>16));
//trig timer0
SETREG16(EDISON_BASE_REG_TIMER0_PA, TIMER_TRIG);
#endif
}
performance_timer()
: start_(0)
, finish_(0)
{
query_frequency();
start();
}
void __init chip_init_ptimer(void){
unsigned long interval,temp;
/* set up interrupt controller attributes for the timer
interrupt
*/
#ifdef CONFIG_MSTAR_ARM_BD_FPGA
GLB_TIMER_FREQ_KHZ= 24*1000/2 ; // PERIPHCLK = CPU Clock / 2
#else
GLB_TIMER_FREQ_KHZ=(query_frequency()*1000)/ 2; // PERIPHCLK = CPU Clock / 2
#endif
printk("CPU Clock Frequency = %d MHz\n",GLB_TIMER_FREQ_KHZ*2/1000);
//clear timer event flag
PERI_W(PT_STATUS,FLAG_EVENT);
//set timer interrupt interval
interval = ( GLB_TIMER_FREQ_KHZ * 1000 / HZ );
PERI_W(PT_LOADER,interval);
//Interrupt Set Enable Register
temp=PERI_R(GIC_DIST_SET_EANBLE);
temp= temp | (0x1 << INT_ID_PTIMER);
PERI_W(GIC_DIST_SET_EANBLE,temp);
//setup timer IRQ
setup_irq(INT_ID_PTIMER, &chip_ptimer_irq);
//set AUTO Reload & Timer Interrupt
//PERI_W(PT_CONTROL,(FLAG_IT_ENABLE | FLAG_AUTO_RELOAD));
//start timer
PERI_W(PT_CONTROL,(FLAG_TIMER_PRESCALAR | FLAG_IT_ENABLE | FLAG_AUTO_RELOAD| FLAG_TIMER_ENABLE));
}
