int rt2x00usb_write_tx_data(struct rt2x00_dev *rt2x00dev,
struct data_queue *queue, struct sk_buff *skb,
struct ieee80211_tx_control *control)
{
struct usb_device *usb_dev = rt2x00dev_usb_dev(rt2x00dev);
struct queue_entry *entry = rt2x00queue_get_entry(queue, Q_INDEX);
struct queue_entry_priv_usb_tx *priv_tx = entry->priv_data;
struct skb_frame_desc *skbdesc;
u32 length;
if (rt2x00queue_full(queue))
return -EINVAL;
if (test_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags)) {
ERROR(rt2x00dev,
"Arrived at non-free entry in the non-full queue %d.\n"
"Please file bug report to %s.\n",
control->queue, DRV_PROJECT);
return -EINVAL;
}
/*
* Add the descriptor in front of the skb.
*/
skb_push(skb, queue->desc_size);
memset(skb->data, 0, queue->desc_size);
/*
* Fill in skb descriptor
*/
skbdesc = get_skb_frame_desc(skb);
skbdesc->data = skb->data + queue->desc_size;
skbdesc->data_len = skb->len - queue->desc_size;
skbdesc->desc = skb->data;
skbdesc->desc_len = queue->desc_size;
skbdesc->entry = entry;
memcpy(&priv_tx->control, control, sizeof(priv_tx->control));
rt2x00lib_write_tx_desc(rt2x00dev, skb, control);
/*
* USB devices cannot blindly pass the skb->len as the
* length of the data to usb_fill_bulk_urb. Pass the skb
* to the driver to determine what the length should be.
*/
length = rt2x00dev->ops->lib->get_tx_data_len(rt2x00dev, skb);
/*
* Initialize URB and send the frame to the device.
*/
__set_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags);
usb_fill_bulk_urb(priv_tx->urb, usb_dev, usb_sndbulkpipe(usb_dev, 1),
skb->data, length, rt2x00usb_interrupt_txdone, entry);
usb_submit_urb(priv_tx->urb, GFP_ATOMIC);
rt2x00queue_index_inc(queue, Q_INDEX);
return 0;
}
/*
* TX data handlers.
*/
static void rt2x00usb_interrupt_txdone(struct urb *urb)
{
struct queue_entry *entry = (struct queue_entry *)urb->context;
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
struct queue_entry_priv_usb_tx *priv_tx = entry->priv_data;
struct txdone_entry_desc txdesc;
__le32 *txd = (__le32 *)entry->skb->data;
u32 word;
if (!test_bit(DEVICE_ENABLED_RADIO, &rt2x00dev->flags) ||
!__test_and_clear_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags))
return;
rt2x00_desc_read(txd, 0, &word);
/*
* Remove the descriptor data from the buffer.
*/
skb_pull(entry->skb, entry->queue->desc_size);
/*
* Obtain the status about this packet.
*/
txdesc.status = !urb->status ? TX_SUCCESS : TX_FAIL_RETRY;
txdesc.retry = 0;
txdesc.control = &priv_tx->control;
rt2x00lib_txdone(entry, &txdesc);
/*
* Make this entry available for reuse.
*/
entry->flags = 0;
rt2x00queue_index_inc(entry->queue, Q_INDEX_DONE);
/*
* If the data queue was full before the txdone handler
* we must make sure the packet queue in the mac80211 stack
* is reenabled when the txdone handler has finished.
*/
if (!rt2x00queue_full(entry->queue))
ieee80211_wake_queue(rt2x00dev->hw, priv_tx->control.queue);
}
void rt2x00lib_rxdone(struct queue_entry *entry)
{
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
struct rxdone_entry_desc rxdesc;
struct sk_buff *skb;
struct ieee80211_rx_status *rx_status;
unsigned int header_length;
int rate_idx;
if (!test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags) ||
!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
goto submit_entry;
if (test_bit(ENTRY_DATA_IO_FAILED, &entry->flags))
goto submit_entry;
/*
* Allocate a new sk_buffer. If no new buffer available, drop the
* received frame and reuse the existing buffer.
*/
skb = rt2x00queue_alloc_rxskb(entry);
if (!skb)
goto submit_entry;
/*
* Unmap the skb.
*/
rt2x00queue_unmap_skb(entry);
/*
* Extract the RXD details.
*/
memset(&rxdesc, 0, sizeof(rxdesc));
rt2x00dev->ops->lib->fill_rxdone(entry, &rxdesc);
/*
* Check for valid size in case we get corrupted descriptor from
* hardware.
*/
if (unlikely(rxdesc.size == 0 ||
rxdesc.size > entry->queue->data_size)) {
WARNING(rt2x00dev, "Wrong frame size %d max %d.\n",
rxdesc.size, entry->queue->data_size);
dev_kfree_skb(entry->skb);
goto renew_skb;
}
/*
* The data behind the ieee80211 header must be
* aligned on a 4 byte boundary.
*/
header_length = ieee80211_get_hdrlen_from_skb(entry->skb);
/*
* Hardware might have stripped the IV/EIV/ICV data,
* in that case it is possible that the data was
* provided separately (through hardware descriptor)
* in which case we should reinsert the data into the frame.
*/
if ((rxdesc.dev_flags & RXDONE_CRYPTO_IV) &&
(rxdesc.flags & RX_FLAG_IV_STRIPPED))
rt2x00crypto_rx_insert_iv(entry->skb, header_length,
&rxdesc);
else if (header_length &&
(rxdesc.size > header_length) &&
(rxdesc.dev_flags & RXDONE_L2PAD))
rt2x00queue_remove_l2pad(entry->skb, header_length);
/* Trim buffer to correct size */
skb_trim(entry->skb, rxdesc.size);
/*
* Translate the signal to the correct bitrate index.
*/
rate_idx = rt2x00lib_rxdone_read_signal(rt2x00dev, &rxdesc);
if (rxdesc.rate_mode == RATE_MODE_HT_MIX ||
rxdesc.rate_mode == RATE_MODE_HT_GREENFIELD)
rxdesc.flags |= RX_FLAG_HT;
/*
* Check if this is a beacon, and more frames have been
* buffered while we were in powersaving mode.
*/
rt2x00lib_rxdone_check_ps(rt2x00dev, entry->skb, &rxdesc);
/*
* Update extra components
*/
rt2x00link_update_stats(rt2x00dev, entry->skb, &rxdesc);
rt2x00debug_update_crypto(rt2x00dev, &rxdesc);
rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_RXDONE, entry->skb);
/*
* Initialize RX status information, and send frame
* to mac80211.
*/
rx_status = IEEE80211_SKB_RXCB(entry->skb);
rx_status->mactime = rxdesc.timestamp;
rx_status->band = rt2x00dev->curr_band;
rx_status->freq = rt2x00dev->curr_freq;
rx_status->rate_idx = rate_idx;
rx_status->signal = rxdesc.rssi;
rx_status->flag = rxdesc.flags;
rx_status->antenna = rt2x00dev->link.ant.active.rx;
ieee80211_rx_ni(rt2x00dev->hw, entry->skb);
renew_skb:
/*
* Replace the skb with the freshly allocated one.
*/
entry->skb = skb;
submit_entry:
entry->flags = 0;
rt2x00queue_index_inc(entry, Q_INDEX_DONE);
if (test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags) &&
test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
rt2x00dev->ops->lib->clear_entry(entry);
}
void rt2x00lib_txdone(struct queue_entry *entry,
struct txdone_entry_desc *txdesc)
{
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
unsigned int header_length, i;
u8 rate_idx, rate_flags, retry_rates;
u8 skbdesc_flags = skbdesc->flags;
bool success;
/*
* Unmap the skb.
*/
rt2x00queue_unmap_skb(entry);
/*
* Remove the extra tx headroom from the skb.
*/
skb_pull(entry->skb, rt2x00dev->ops->extra_tx_headroom);
/*
* Signal that the TX descriptor is no longer in the skb.
*/
skbdesc->flags &= ~SKBDESC_DESC_IN_SKB;
/*
* Determine the length of 802.11 header.
*/
header_length = ieee80211_get_hdrlen_from_skb(entry->skb);
/*
* Remove L2 padding which was added during
*/
if (test_bit(REQUIRE_L2PAD, &rt2x00dev->cap_flags))
rt2x00queue_remove_l2pad(entry->skb, header_length);
/*
* If the IV/EIV data was stripped from the frame before it was
* passed to the hardware, we should now reinsert it again because
* mac80211 will expect the same data to be present it the
* frame as it was passed to us.
*/
if (test_bit(CAPABILITY_HW_CRYPTO, &rt2x00dev->cap_flags))
rt2x00crypto_tx_insert_iv(entry->skb, header_length);
/*
* Send frame to debugfs immediately, after this call is completed
* we are going to overwrite the skb->cb array.
*/
rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_TXDONE, entry->skb);
/*
* Determine if the frame has been successfully transmitted.
*/
success =
test_bit(TXDONE_SUCCESS, &txdesc->flags) ||
test_bit(TXDONE_UNKNOWN, &txdesc->flags);
/*
* Update TX statistics.
*/
rt2x00dev->link.qual.tx_success += success;
rt2x00dev->link.qual.tx_failed += !success;
rate_idx = skbdesc->tx_rate_idx;
rate_flags = skbdesc->tx_rate_flags;
retry_rates = test_bit(TXDONE_FALLBACK, &txdesc->flags) ?
(txdesc->retry + 1) : 1;
/*
* Initialize TX status
*/
memset(&tx_info->status, 0, sizeof(tx_info->status));
tx_info->status.ack_signal = 0;
/*
* Frame was send with retries, hardware tried
* different rates to send out the frame, at each
* retry it lowered the rate 1 step except when the
* lowest rate was used.
*/
for (i = 0; i < retry_rates && i < IEEE80211_TX_MAX_RATES; i++) {
tx_info->status.rates[i].idx = rate_idx - i;
tx_info->status.rates[i].flags = rate_flags;
if (rate_idx - i == 0) {
/*
* The lowest rate (index 0) was used until the
* number of max retries was reached.
*/
tx_info->status.rates[i].count = retry_rates - i;
i++;
break;
}
tx_info->status.rates[i].count = 1;
}
if (i < (IEEE80211_TX_MAX_RATES - 1))
tx_info->status.rates[i].idx = -1; /* terminate */
if (!(tx_info->flags & IEEE80211_TX_CTL_NO_ACK)) {
if (success)
tx_info->flags |= IEEE80211_TX_STAT_ACK;
else
rt2x00dev->low_level_stats.dot11ACKFailureCount++;
}
/*
* Every single frame has it's own tx status, hence report
* every frame as ampdu of size 1.
*
* TODO: if we can find out how many frames were aggregated
* by the hw we could provide the real ampdu_len to mac80211
* which would allow the rc algorithm to better decide on
* which rates are suitable.
*/
if (test_bit(TXDONE_AMPDU, &txdesc->flags) ||
tx_info->flags & IEEE80211_TX_CTL_AMPDU) {
tx_info->flags |= IEEE80211_TX_STAT_AMPDU;
tx_info->status.ampdu_len = 1;
tx_info->status.ampdu_ack_len = success ? 1 : 0;
if (!success)
tx_info->flags |= IEEE80211_TX_STAT_AMPDU_NO_BACK;
}
if (rate_flags & IEEE80211_TX_RC_USE_RTS_CTS) {
if (success)
rt2x00dev->low_level_stats.dot11RTSSuccessCount++;
else
rt2x00dev->low_level_stats.dot11RTSFailureCount++;
}
/*
* Only send the status report to mac80211 when it's a frame
* that originated in mac80211. If this was a extra frame coming
* through a mac80211 library call (RTS/CTS) then we should not
* send the status report back.
*/
if (!(skbdesc_flags & SKBDESC_NOT_MAC80211)) {
if (test_bit(REQUIRE_TASKLET_CONTEXT, &rt2x00dev->cap_flags))
ieee80211_tx_status(rt2x00dev->hw, entry->skb);
else
ieee80211_tx_status_ni(rt2x00dev->hw, entry->skb);
} else
dev_kfree_skb_any(entry->skb);
/*
* Make this entry available for reuse.
*/
entry->skb = NULL;
entry->flags = 0;
rt2x00dev->ops->lib->clear_entry(entry);
rt2x00queue_index_inc(entry, Q_INDEX_DONE);
/*
* If the data queue was below the threshold before the txdone
* handler we must make sure the packet queue in the mac80211 stack
* is reenabled when the txdone handler has finished. This has to be
* serialized with rt2x00mac_tx(), otherwise we can wake up queue
* before it was stopped.
*/
spin_lock_bh(&entry->queue->tx_lock);
if (!rt2x00queue_threshold(entry->queue))
rt2x00queue_unpause_queue(entry->queue);
spin_unlock_bh(&entry->queue->tx_lock);
}
void rt2x00lib_dmadone(struct queue_entry *entry)
{
set_bit(ENTRY_DATA_STATUS_PENDING, &entry->flags);
clear_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags);
rt2x00queue_index_inc(entry, Q_INDEX_DMA_DONE);
}
void rt2x00lib_dmastart(struct queue_entry *entry)
{
set_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags);
rt2x00queue_index_inc(entry, Q_INDEX);
}
void rt2x00lib_rxdone(struct rt2x00_dev *rt2x00dev,
struct queue_entry *entry)
{
struct rxdone_entry_desc rxdesc;
struct sk_buff *skb;
struct ieee80211_rx_status *rx_status = &rt2x00dev->rx_status;
unsigned int header_length;
int rate_idx;
/*
* Allocate a new sk_buffer. If no new buffer available, drop the
* received frame and reuse the existing buffer.
*/
skb = rt2x00queue_alloc_rxskb(rt2x00dev, entry);
if (!skb)
return;
/*
* Unmap the skb.
*/
rt2x00queue_unmap_skb(rt2x00dev, entry->skb);
/*
* Extract the RXD details.
*/
memset(&rxdesc, 0, sizeof(rxdesc));
rt2x00dev->ops->lib->fill_rxdone(entry, &rxdesc);
/* Trim buffer to correct size */
skb_trim(entry->skb, rxdesc.size);
/*
* The data behind the ieee80211 header must be
* aligned on a 4 byte boundary.
*/
header_length = ieee80211_get_hdrlen_from_skb(entry->skb);
/*
* Hardware might have stripped the IV/EIV/ICV data,
* in that case it is possible that the data was
* provided seperately (through hardware descriptor)
* in which case we should reinsert the data into the frame.
*/
if ((rxdesc.dev_flags & RXDONE_CRYPTO_IV) &&
(rxdesc.flags & RX_FLAG_IV_STRIPPED))
rt2x00crypto_rx_insert_iv(entry->skb, header_length,
&rxdesc);
else if (rxdesc.dev_flags & RXDONE_L2PAD)
rt2x00queue_remove_l2pad(entry->skb, header_length);
else
rt2x00queue_align_payload(entry->skb, header_length);
/*
* Check if the frame was received using HT. In that case,
* the rate is the MCS index and should be passed to mac80211
* directly. Otherwise we need to translate the signal to
* the correct bitrate index.
*/
if (rxdesc.rate_mode == RATE_MODE_CCK ||
rxdesc.rate_mode == RATE_MODE_OFDM) {
rate_idx = rt2x00lib_rxdone_read_signal(rt2x00dev, &rxdesc);
} else {
rxdesc.flags |= RX_FLAG_HT;
rate_idx = rxdesc.signal;
}
/*
* Update extra components
*/
rt2x00link_update_stats(rt2x00dev, entry->skb, &rxdesc);
rt2x00debug_update_crypto(rt2x00dev, &rxdesc);
rx_status->mactime = rxdesc.timestamp;
rx_status->rate_idx = rate_idx;
rx_status->signal = rxdesc.rssi;
rx_status->noise = rxdesc.noise;
rx_status->flag = rxdesc.flags;
rx_status->antenna = rt2x00dev->link.ant.active.rx;
/*
* Send frame to mac80211 & debugfs.
* mac80211 will clean up the skb structure.
*/
rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_RXDONE, entry->skb);
memcpy(IEEE80211_SKB_RXCB(entry->skb), rx_status, sizeof(*rx_status));
ieee80211_rx_irqsafe(rt2x00dev->hw, entry->skb);
/*
* Replace the skb with the freshly allocated one.
*/
entry->skb = skb;
entry->flags = 0;
rt2x00dev->ops->lib->clear_entry(entry);
rt2x00queue_index_inc(entry->queue, Q_INDEX);
}
void rt2x00lib_txdone(struct queue_entry *entry,
struct txdone_entry_desc *txdesc)
{
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
enum data_queue_qid qid = skb_get_queue_mapping(entry->skb);
unsigned int header_length = ieee80211_get_hdrlen_from_skb(entry->skb);
u8 rate_idx, rate_flags, retry_rates;
u8 skbdesc_flags = skbdesc->flags;
unsigned int i;
bool success;
/*
* Unmap the skb.
*/
rt2x00queue_unmap_skb(rt2x00dev, entry->skb);
/*
* Remove L2 padding which was added during
*/
if (test_bit(DRIVER_REQUIRE_L2PAD, &rt2x00dev->flags))
rt2x00queue_remove_l2pad(entry->skb, header_length);
/*
* If the IV/EIV data was stripped from the frame before it was
* passed to the hardware, we should now reinsert it again because
* mac80211 will expect the the same data to be present it the
* frame as it was passed to us.
*/
if (test_bit(CONFIG_SUPPORT_HW_CRYPTO, &rt2x00dev->flags))
rt2x00crypto_tx_insert_iv(entry->skb, header_length);
/*
* Send frame to debugfs immediately, after this call is completed
* we are going to overwrite the skb->cb array.
*/
rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_TXDONE, entry->skb);
/*
* Determine if the frame has been successfully transmitted.
*/
success =
test_bit(TXDONE_SUCCESS, &txdesc->flags) ||
test_bit(TXDONE_UNKNOWN, &txdesc->flags) ||
test_bit(TXDONE_FALLBACK, &txdesc->flags);
/*
* Update TX statistics.
*/
rt2x00dev->link.qual.tx_success += success;
rt2x00dev->link.qual.tx_failed += !success;
rate_idx = skbdesc->tx_rate_idx;
rate_flags = skbdesc->tx_rate_flags;
retry_rates = test_bit(TXDONE_FALLBACK, &txdesc->flags) ?
(txdesc->retry + 1) : 1;
/*
* Initialize TX status
*/
memset(&tx_info->status, 0, sizeof(tx_info->status));
tx_info->status.ack_signal = 0;
/*
* Frame was send with retries, hardware tried
* different rates to send out the frame, at each
* retry it lowered the rate 1 step.
*/
for (i = 0; i < retry_rates && i < IEEE80211_TX_MAX_RATES; i++) {
tx_info->status.rates[i].idx = rate_idx - i;
tx_info->status.rates[i].flags = rate_flags;
tx_info->status.rates[i].count = 1;
}
if (i < (IEEE80211_TX_MAX_RATES - 1))
tx_info->status.rates[i].idx = -1; /* terminate */
if (!(tx_info->flags & IEEE80211_TX_CTL_NO_ACK)) {
if (success)
tx_info->flags |= IEEE80211_TX_STAT_ACK;
else
rt2x00dev->low_level_stats.dot11ACKFailureCount++;
}
if (rate_flags & IEEE80211_TX_RC_USE_RTS_CTS) {
if (success)
rt2x00dev->low_level_stats.dot11RTSSuccessCount++;
else
rt2x00dev->low_level_stats.dot11RTSFailureCount++;
}
/*
* Only send the status report to mac80211 when it's a frame
* that originated in mac80211. If this was a extra frame coming
* through a mac80211 library call (RTS/CTS) then we should not
* send the status report back.
*/
if (!(skbdesc_flags & SKBDESC_NOT_MAC80211))
ieee80211_tx_status_irqsafe(rt2x00dev->hw, entry->skb);
else
dev_kfree_skb_irq(entry->skb);
/*
* Make this entry available for reuse.
*/
entry->skb = NULL;
entry->flags = 0;
rt2x00dev->ops->lib->clear_entry(entry);
clear_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags);
rt2x00queue_index_inc(entry->queue, Q_INDEX_DONE);
/*
* If the data queue was below the threshold before the txdone
* handler we must make sure the packet queue in the mac80211 stack
* is reenabled when the txdone handler has finished.
*/
if (!rt2x00queue_threshold(entry->queue))
ieee80211_wake_queue(rt2x00dev->hw, qid);
}
static void rt2x00usb_interrupt_rxdone(struct urb *urb)
{
struct queue_entry *entry = (struct queue_entry *)urb->context;
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
struct sk_buff *skb;
struct skb_frame_desc *skbdesc;
struct rxdone_entry_desc rxdesc;
int header_size;
if (!test_bit(DEVICE_ENABLED_RADIO, &rt2x00dev->flags) ||
!test_and_clear_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags))
return;
/*
* Check if the received data is simply too small
* to be actually valid, or if the urb is signaling
* a problem.
*/
if (urb->actual_length < entry->queue->desc_size || urb->status)
goto skip_entry;
/*
* Fill in skb descriptor
*/
skbdesc = get_skb_frame_desc(entry->skb);
memset(skbdesc, 0, sizeof(*skbdesc));
skbdesc->entry = entry;
memset(&rxdesc, 0, sizeof(rxdesc));
rt2x00dev->ops->lib->fill_rxdone(entry, &rxdesc);
/*
* The data behind the ieee80211 header must be
* aligned on a 4 byte boundary.
*/
header_size = ieee80211_get_hdrlen_from_skb(entry->skb);
if (header_size % 4 == 0) {
skb_push(entry->skb, 2);
memmove(entry->skb->data, entry->skb->data + 2,
entry->skb->len - 2);
skbdesc->data = entry->skb->data;
skb_trim(entry->skb,entry->skb->len - 2);
}
/*
* Allocate a new sk buffer to replace the current one.
* If allocation fails, we should drop the current frame
* so we can recycle the existing sk buffer for the new frame.
*/
skb = rt2x00usb_alloc_rxskb(entry->queue);
if (!skb)
goto skip_entry;
/*
* Send the frame to rt2x00lib for further processing.
*/
rt2x00lib_rxdone(entry, &rxdesc);
/*
* Replace current entry's skb with the newly allocated one,
* and reinitialize the urb.
*/
entry->skb = skb;
urb->transfer_buffer = entry->skb->data;
urb->transfer_buffer_length = entry->skb->len;
skip_entry:
if (test_bit(DEVICE_ENABLED_RADIO, &entry->queue->rt2x00dev->flags)) {
__set_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags);
usb_submit_urb(urb, GFP_ATOMIC);
}
rt2x00queue_index_inc(entry->queue, Q_INDEX);
}
void rt2x00lib_dmadone(struct queue_entry *entry)
{
clear_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags);
rt2x00queue_index_inc(entry->queue, Q_INDEX_DMA_DONE);
}
void rt2x00lib_rxdone(struct rt2x00_dev *rt2x00dev,
struct queue_entry *entry)
{
struct rxdone_entry_desc rxdesc;
struct sk_buff *skb;
struct ieee80211_rx_status *rx_status = &rt2x00dev->rx_status;
struct ieee80211_supported_band *sband;
struct ieee80211_hdr *hdr;
const struct rt2x00_rate *rate;
unsigned int header_size;
unsigned int align;
unsigned int i;
int idx = -1;
/*
* Allocate a new sk_buffer. If no new buffer available, drop the
* received frame and reuse the existing buffer.
*/
skb = rt2x00queue_alloc_rxskb(rt2x00dev, entry);
if (!skb)
return;
/*
* Unmap the skb.
*/
rt2x00queue_unmap_skb(rt2x00dev, entry->skb);
/*
* Extract the RXD details.
*/
memset(&rxdesc, 0, sizeof(rxdesc));
rt2x00dev->ops->lib->fill_rxdone(entry, &rxdesc);
/*
* The data behind the ieee80211 header must be
* aligned on a 4 byte boundary.
*/
header_size = ieee80211_get_hdrlen_from_skb(entry->skb);
align = ((unsigned long)(entry->skb->data + header_size)) & 3;
if (align) {
skb_push(entry->skb, align);
/* Move entire frame in 1 command */
memmove(entry->skb->data, entry->skb->data + align,
rxdesc.size);
}
/* Update data pointers, trim buffer to correct size */
skb_trim(entry->skb, rxdesc.size);
/*
* Update RX statistics.
*/
sband = &rt2x00dev->bands[rt2x00dev->curr_band];
for (i = 0; i < sband->n_bitrates; i++) {
rate = rt2x00_get_rate(sband->bitrates[i].hw_value);
if (((rxdesc.dev_flags & RXDONE_SIGNAL_PLCP) &&
(rate->plcp == rxdesc.signal)) ||
(!(rxdesc.dev_flags & RXDONE_SIGNAL_PLCP) &&
(rate->bitrate == rxdesc.signal))) {
idx = i;
break;
}
}
if (idx < 0) {
WARNING(rt2x00dev, "Frame received with unrecognized signal,"
"signal=0x%.2x, plcp=%d.\n", rxdesc.signal,
!!(rxdesc.dev_flags & RXDONE_SIGNAL_PLCP));
idx = 0;
}
/*
* Only update link status if this is a beacon frame carrying our bssid.
*/
hdr = (struct ieee80211_hdr *)entry->skb->data;
if (ieee80211_is_beacon(hdr->frame_control) &&
(rxdesc.dev_flags & RXDONE_MY_BSS))
rt2x00lib_update_link_stats(&rt2x00dev->link, rxdesc.rssi);
rt2x00dev->link.qual.rx_success++;
rx_status->mactime = rxdesc.timestamp;
rx_status->rate_idx = idx;
rx_status->qual =
rt2x00lib_calculate_link_signal(rt2x00dev, rxdesc.rssi);
rx_status->signal = rxdesc.rssi;
rx_status->flag = rxdesc.flags;
rx_status->antenna = rt2x00dev->link.ant.active.rx;
/*
* Send frame to mac80211 & debugfs.
* mac80211 will clean up the skb structure.
*/
rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_RXDONE, entry->skb);
ieee80211_rx_irqsafe(rt2x00dev->hw, entry->skb, rx_status);
/*
* Replace the skb with the freshly allocated one.
*/
entry->skb = skb;
entry->flags = 0;
rt2x00dev->ops->lib->init_rxentry(rt2x00dev, entry);
rt2x00queue_index_inc(entry->queue, Q_INDEX);
}
void rt2x00lib_txdone(struct queue_entry *entry,
struct txdone_entry_desc *txdesc)
{
struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(entry->skb);
enum data_queue_qid qid = skb_get_queue_mapping(entry->skb);
/*
* Unmap the skb.
*/
rt2x00queue_unmap_skb(rt2x00dev, entry->skb);
/*
* Send frame to debugfs immediately, after this call is completed
* we are going to overwrite the skb->cb array.
*/
rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_TXDONE, entry->skb);
/*
* Update TX statistics.
*/
rt2x00dev->link.qual.tx_success +=
test_bit(TXDONE_SUCCESS, &txdesc->flags);
rt2x00dev->link.qual.tx_failed +=
test_bit(TXDONE_FAILURE, &txdesc->flags);
/*
* Initialize TX status
*/
memset(&tx_info->status, 0, sizeof(tx_info->status));
tx_info->status.ack_signal = 0;
tx_info->status.excessive_retries =
test_bit(TXDONE_EXCESSIVE_RETRY, &txdesc->flags);
tx_info->status.retry_count = txdesc->retry;
if (!(tx_info->flags & IEEE80211_TX_CTL_NO_ACK)) {
if (test_bit(TXDONE_SUCCESS, &txdesc->flags))
tx_info->flags |= IEEE80211_TX_STAT_ACK;
else if (test_bit(TXDONE_FAILURE, &txdesc->flags))
rt2x00dev->low_level_stats.dot11ACKFailureCount++;
}
if (tx_info->flags & IEEE80211_TX_CTL_USE_RTS_CTS) {
if (test_bit(TXDONE_SUCCESS, &txdesc->flags))
rt2x00dev->low_level_stats.dot11RTSSuccessCount++;
else if (test_bit(TXDONE_FAILURE, &txdesc->flags))
rt2x00dev->low_level_stats.dot11RTSFailureCount++;
}
/*
* Only send the status report to mac80211 when TX status was
* requested by it. If this was a extra frame coming through
* a mac80211 library call (RTS/CTS) then we should not send the
* status report back.
*/
if (tx_info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS)
ieee80211_tx_status_irqsafe(rt2x00dev->hw, entry->skb);
else
dev_kfree_skb_irq(entry->skb);
/*
* Make this entry available for reuse.
*/
entry->skb = NULL;
entry->flags = 0;
rt2x00dev->ops->lib->init_txentry(rt2x00dev, entry);
__clear_bit(ENTRY_OWNER_DEVICE_DATA, &entry->flags);
rt2x00queue_index_inc(entry->queue, Q_INDEX_DONE);
/*
* If the data queue was below the threshold before the txdone
* handler we must make sure the packet queue in the mac80211 stack
* is reenabled when the txdone handler has finished.
*/
if (!rt2x00queue_threshold(entry->queue))
ieee80211_wake_queue(rt2x00dev->hw, qid);
}