static void __init simpad_map_io(void)
{
sa1100_map_io();
iotable_init(simpad_io_desc, ARRAY_SIZE(simpad_io_desc));
set_cs3_bit (EN1 | EN0 | LED2_ON | DISPLAY_ON | RS232_ON |
ENABLE_5V | RESET_SIMCARD | DECT_POWER_ON);
sa1100_register_uart_fns(&simpad_port_fns);
sa1100_register_uart(0, 3); /* serial interface */
sa1100_register_uart(1, 1); /* DECT */
// Reassign UART 1 pins
GAFR |= GPIO_UART_TXD | GPIO_UART_RXD;
GPDR |= GPIO_UART_TXD | GPIO_LDD13 | GPIO_LDD15;
GPDR &= ~GPIO_UART_RXD;
PPAR |= PPAR_UPR;
/*
* Set up registers for sleep mode.
*/
PWER = PWER_GPIO0| PWER_RTC;
PGSR = 0x818;
PCFR = 0;
PSDR = 0;
sa11x0_set_flash_data(&simpad_flash_data, simpad_flash_resources,
ARRAY_SIZE(simpad_flash_resources));
sa11x0_set_mcp_data(&simpad_mcp_data);
}
static void __init assabet_init(void)
{
/*
* Ensure that the power supply is in "high power" mode.
*/
GPDR |= GPIO_GPIO16;
GPSR = GPIO_GPIO16;
/*
* Ensure that these pins are set as outputs and are driving
* logic 0. This ensures that we won't inadvertently toggle
* the WS latch in the CPLD, and we don't float causing
* excessive power drain. --rmk
*/
GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
GPCR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
/*
* Set up registers for sleep mode.
*/
PWER = PWER_GPIO0;
PGSR = 0;
PCFR = 0;
PSDR = 0;
PPDR |= PPC_TXD3 | PPC_TXD1;
PPSR |= PPC_TXD3 | PPC_TXD1;
sa1100fb_lcd_power = assabet_lcd_power;
sa1100fb_backlight_power = assabet_backlight_power;
if (machine_has_neponset()) {
/*
* Angel sets this, but other bootloaders may not.
*
* This must precede any driver calls to BCR_set()
* or BCR_clear().
*/
ASSABET_BCR = BCR_value = ASSABET_BCR_DB1111;
#ifndef CONFIG_ASSABET_NEPONSET
printk( "Warning: Neponset detected but full support "
"hasn't been configured in the kernel\n" );
#endif
}
sa11x0_set_flash_data(&assabet_flash_data, assabet_flash_resources,
ARRAY_SIZE(assabet_flash_resources));
sa11x0_set_irda_data(&assabet_irda_data);
sa11x0_set_mcp_data(&assabet_mcp_data);
}
static void __init collie_init(void)
{
int ret = 0;
GAFR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM | GPIO_SSP_CLK |
GPIO_MCP_CLK | GPIO_32_768kHz;
GPDR = GPIO_LDD8 | GPIO_LDD9 | GPIO_LDD10 | GPIO_LDD11 | GPIO_LDD12 |
GPIO_LDD13 | GPIO_LDD14 | GPIO_LDD15 | GPIO_SSP_TXD |
GPIO_SSP_SCLK | GPIO_SSP_SFRM | GPIO_SDLC_SCLK |
COLLIE_GPIO_UCB1x00_RESET | COLLIE_GPIO_nMIC_ON |
COLLIE_GPIO_nREMOCON_ON | GPIO_32_768kHz;
PPDR = PPC_LDD0 | PPC_LDD1 | PPC_LDD2 | PPC_LDD3 | PPC_LDD4 | PPC_LDD5 |
PPC_LDD6 | PPC_LDD7 | PPC_L_PCLK | PPC_L_LCLK | PPC_L_FCLK | PPC_L_BIAS |
PPC_TXD1 | PPC_TXD2 | PPC_TXD3 | PPC_TXD4 | PPC_SCLK | PPC_SFRM;
PWER = COLLIE_GPIO_AC_IN | COLLIE_GPIO_CO | COLLIE_GPIO_ON_KEY |
COLLIE_GPIO_WAKEUP | COLLIE_GPIO_nREMOCON_INT | PWER_RTC;
PGSR = COLLIE_GPIO_nREMOCON_ON;
PSDR = PPC_RXD1 | PPC_RXD2 | PPC_RXD3 | PPC_RXD4;
PCFR = PCFR_OPDE;
platform_scoop_config = &collie_pcmcia_config;
ret = platform_add_devices(devices, ARRAY_SIZE(devices));
if (ret) {
printk(KERN_WARNING "collie: Unable to register LoCoMo device\n");
}
sa11x0_set_flash_data(&collie_flash_data, collie_flash_resources,
ARRAY_SIZE(collie_flash_resources));
sa11x0_set_mcp_data(&collie_mcp_data);
sharpsl_save_param();
}
static void __init collie_init(void)
{
int ret = 0;
/* cpu initialize */
GAFR = ( GPIO_SSP_TXD | \
GPIO_SSP_SCLK | GPIO_SSP_SFRM | GPIO_SSP_CLK | GPIO_TIC_ACK | \
GPIO_32_768kHz );
GPDR = ( GPIO_LDD8 | GPIO_LDD9 | GPIO_LDD10 | GPIO_LDD11 | GPIO_LDD12 | \
GPIO_LDD13 | GPIO_LDD14 | GPIO_LDD15 | GPIO_SSP_TXD | \
GPIO_SSP_SCLK | GPIO_SSP_SFRM | GPIO_SDLC_SCLK | \
GPIO_SDLC_AAF | GPIO_UART_SCLK1 | GPIO_32_768kHz );
GPLR = GPIO_GPIO18;
// PPC pin setting
PPDR = ( PPC_LDD0 | PPC_LDD1 | PPC_LDD2 | PPC_LDD3 | PPC_LDD4 | PPC_LDD5 | \
PPC_LDD6 | PPC_LDD7 | PPC_L_PCLK | PPC_L_LCLK | PPC_L_FCLK | PPC_L_BIAS | \
PPC_TXD1 | PPC_TXD2 | PPC_RXD2 | PPC_TXD3 | PPC_TXD4 | PPC_SCLK | PPC_SFRM );
PSDR = ( PPC_RXD1 | PPC_RXD2 | PPC_RXD3 | PPC_RXD4 );
GAFR |= GPIO_32_768kHz;
GPDR |= GPIO_32_768kHz;
TUCR = TUCR_32_768kHz;
platform_scoop_config = &collie_pcmcia_config;
ret = platform_add_devices(devices, ARRAY_SIZE(devices));
if (ret) {
printk(KERN_WARNING "collie: Unable to register LoCoMo device\n");
}
sa11x0_set_flash_data(&collie_flash_data, collie_flash_resources,
ARRAY_SIZE(collie_flash_resources));
sa11x0_set_mcp_data(&collie_mcp_data);
sharpsl_save_param();
}
static void __init shannon_init(void)
{
sa11x0_set_flash_data(&shannon_flash_data, &shannon_flash_resource, 1);
sa11x0_set_mcp_data(&shannon_mcp_data);
}
static void __init cerf_init(void)
{
platform_add_devices(cerf_devices, ARRAY_SIZE(cerf_devices));
sa11x0_set_flash_data(&cerf_flash_data, &cerf_flash_resource, 1);
sa11x0_set_mcp_data(&cerf_mcp_data);
}
