static void sch_setup_non_standard_bars(void)
{
printk(BIOS_DEBUG, "Setting up ACPI PM1 block ");
/* Address 0x1000 size 16B */
pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x48,
(0x80000000 | DEFAULT_PMBASE));
printk(BIOS_DEBUG, "Setting up ACPI P block ");
/* Address 0x1010 size 16B */
sch_port_access_write(4, 0x70, 4, 0x80001010);
/* SMBus address 0x1040 size 64B */
pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x40, 0x80001040);
/* GPIO address 0x1080 size 64B */
pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x44, 0x80001080);
/* GPE0 address 0x10C0 size 64B */
pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x4C, 0x800010C0);
sch_port_access_write(2, 4, 4, 0x3F703F76); /* FIXME: SMM Control */
/* Base of Stolen Memory Address 0x1080 size 64B */
pci_write_config32(PCI_DEV(0, 0x02, 0), 0x5C, 0x3F800000);
sch_port_access_write(0, 0, 4, DEFAULT_PCIEXBAR | 1); /* pre-b1 */
sch_port_access_write(2, 9, 4, DEFAULT_PCIEXBAR | 1); /* b1+ */
/* RCBA */
pci_write_config32(PCI_DEV(0, 0x1f, 0), 0xF0, (DEFAULT_RCBABASE | 1));
printk(BIOS_DEBUG, " done.\n");
}
static void program_sch_dram_data(struct sys_info *sysinfo)
{
u32 reg32;
/*
* Program DRP DRAM Rank Population and Interface Register as per data
* in sysinfo SCH port 1 register 0..0xFF.
*/
reg32 =
sch_port_access_read(SCH_MSG_DUNIT_PORT, SCH_MSG_DUNIT_REG_DRP, 4);
reg32 &= ~(DRP_FIELDS); /* Clear all DRP fields we'll change. */
/* Rank0 Device Width, Density, Enable */
reg32 |= sysinfo->data_width | (sysinfo->device_density << 1) | (1 << 3);
/* Rank1 Device Width, Density, Enable */
reg32 |= (sysinfo->data_width << 4)
| ((sysinfo->device_density) << 5) | (1 << 7);
sch_port_access_write(SCH_MSG_DUNIT_PORT,
SCH_MSG_DUNIT_REG_DRP, 4, reg32);
/*
* Program DTR DRAM Timing Register as per data in sysinfo SCH port 1
* register 1.
*
* tRD_dly = 2 (15:13 = 010b)
* 0X3F
*/
reg32 =
sch_port_access_read(SCH_MSG_DUNIT_PORT, SCH_MSG_DUNIT_REG_DTR, 4);
reg32 &= ~(DTR_FIELDS); /* Clear all DTR fields we'll change. */
reg32 = (sysinfo->trp);
reg32 |= (sysinfo->trcd) << 2;
reg32 |= (sysinfo->cl) << 4;
reg32 |= 0X4000; /* tRD_dly = 2 (15:13 = 010b) */
sch_port_access_write(SCH_MSG_DUNIT_PORT, SCH_MSG_DUNIT_REG_DTR, 4,
reg32);
/*
* DCO DRAM Controller Operation Register as per data in sysinfo
* SCH port 1 register 2 0xF.
*/
reg32 =
sch_port_access_read(SCH_MSG_DUNIT_PORT, SCH_MSG_DUNIT_REG_DCO, 4);
reg32 &= ~(DCO_FIELDS); /* Clear all DTR fields we'll change. */
if (sysinfo->fsb_frequency == 533)
reg32 |= 1;
else
reg32 &= ~(BIT(0));
reg32 = 0x006911c; // FIXME ?
sch_port_access_write(SCH_MSG_DUNIT_PORT, SCH_MSG_DUNIT_REG_DCO, 4,
reg32);
}
static void poulsbo_setup_Stage1Regs(void)
{
u32 reg32;
printk(BIOS_DEBUG, "E000/F000 Routing ");
reg32 = sch_port_access_read(2, 3, 4);
sch_port_access_write(2, 3, 4, (reg32 | 0x6));
}
static void program_dll_config(struct sys_info *sysinfo)
{
if (sysinfo->fsb_frequency == 533) {
sch_port_access_write(SCH_MSG_DUNIT_PORT, 0x21, 4, 0x46464646);
sch_port_access_write(SCH_MSG_DUNIT_PORT, 0x22, 4, 0x46464646);
} else {
sch_port_access_write(SCH_MSG_DUNIT_PORT, 0x21, 4, 0x58585858);
sch_port_access_write(SCH_MSG_DUNIT_PORT, 0x22, 4, 0x58585858);
}
sch_port_access_write(SCH_MSG_DUNIT_PORT, 0x23, 4, 0x2222);
if (sysinfo->fsb_frequency == 533)
sch_port_access_write(SCH_MSG_DUNIT_PORT, 0x20, 4, 0x993B);
else
sch_port_access_write(SCH_MSG_DUNIT_PORT, 0x20, 4, 0xCC3B);
}
/**
* @param boot_mode 0 = normal, 1 = resume
*/
void sdram_initialize(int boot_mode)
{
struct sys_info sysinfo;
u32 reg32;
printk(BIOS_DEBUG, "Setting up RAM controller.\n");
memset(&sysinfo, 0, sizeof(sysinfo));
detect_fsb(&sysinfo);
detect_softstraps(&sysinfo);
program_sch_dram_data(&sysinfo);
/* cold boot */
if (boot_mode == BOOT_MODE_NORMAL)
do_jedec_init(&sysinfo);
else
program_dll_config(&sysinfo);
/* RAM init complete. */
reg32 =
sch_port_access_read(SCH_MSG_DUNIT_PORT, SCH_MSG_DUNIT_REG_DCO, 4);
reg32 |= DCO_IC;
reg32 |= ((sysinfo.refresh) << 2);
reg32 = 0x006919c;
sch_port_access_write(SCH_MSG_DUNIT_PORT,
SCH_MSG_DUNIT_REG_DCO, 4, reg32);
/* Setting up TOM. */
reg32 = 0x10000000;
reg32 = reg32 >> sysinfo.data_width;
reg32 = reg32 << sysinfo.device_density;
reg32 = reg32 << sysinfo.ranks;
reg32 = 0x40000000;
sch_port_access_write(2, 8, 4, reg32);
/* Resume mode. */
if (boot_mode == BOOT_MODE_RESUME)
sch_port_access_write_ram_cmd(SCH_OPCODE_WAKEFULLON,
SCH_MSG_DUNIT_PORT, 0, 0);
sch_port_access_write(2, 0, 4, 0x98);
sch_port_access_write(2, 3, 4, 0x7);
sch_port_access_write(3, 2, 4, 0x408);
sch_port_access_write(4, 0x71, 4, 0x600);
}
static void do_jedec_init(struct sys_info *sysinfo)
{
u32 reg32, rank, cmd, temp, num_ranks;
/* Performs JEDEC memory initializattion for all memory rows */
/* Set CKE0/1 low */
reg32 =
sch_port_access_read(SCH_MSG_DUNIT_PORT, SCH_MSG_DUNIT_REG_DRP, 4);
reg32 |= DRP_CKE_DIS;
sch_port_access_write(SCH_MSG_DUNIT_PORT,
SCH_MSG_DUNIT_REG_DRP, 4, reg32);
reg32 =
sch_port_access_read(SCH_MSG_DUNIT_PORT, SCH_MSG_DUNIT_REG_DRP, 4);
rank = 0;
num_ranks = sysinfo->ranks;
do {
/* Start clocks */
reg32 = sch_port_access_read(SCH_MSG_DUNIT_PORT,
SCH_MSG_DUNIT_REG_DRP, 4);
reg32 &= ~(DRP_SCK_DIS); /* Enable all SCK/SCKB by def. */
sch_port_access_write(1, SCH_MSG_DUNIT_REG_DRP, 4, reg32);
/* Program misc. SCH registers on rank 0 initialization. */
reg32 = sch_port_access_read(SCH_MSG_DUNIT_PORT,
SCH_MSG_DUNIT_REG_DRP, 4);
if (rank == 0)
program_dll_config(sysinfo);
printk(BIOS_DEBUG, "Setting up RAM \n");
/*
* Wait 200us
* reg32 = inb(ACPI_BASE + 8); PM1 Timer
* reg32 &=0xFFFFFF;
* reg32 +=0x2EE;
* do {
* reg32 = inb(ACPI_BASE + 8);PM1 Timer
* reg32 &= 0xFFFFFF;
* } while (reg32 < 0x2EE);
*/
/* Apply NOP. */
cmd = rank;
cmd |= SCH_DRAMINIT_CMD_NOP;
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
/* Set CKE=high. */
reg32 = sch_port_access_read(SCH_MSG_DUNIT_PORT,
SCH_MSG_DUNIT_REG_DRP, 4);
reg32 &= 0xFFFF9FFF; /* Clear both the CKE static disables. */
sch_port_access_write(SCH_MSG_DUNIT_PORT,
SCH_MSG_DUNIT_REG_DRP, 4, reg32);
/*
* Wait 400ns (not needed when executing from flash).
* Precharge all.
*/
reg32 = sch_port_access_read(SCH_MSG_DUNIT_PORT,
SCH_MSG_DUNIT_REG_DRP, 4);
cmd = rank;
cmd |= SCH_DRAMINIT_CMD_PALL;
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
/*
* EMRS(2); High temp self refresh=disabled,
* partial array self refresh=full.
*/
cmd = rank;
cmd |= SCH_DRAMINIT_CMD_EMRS2;
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
/* EMRS(3) (no command). */
cmd = rank;
cmd |= SCH_DRAMINIT_CMD_EMRS3;
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
/* EMRS(1); Enable DLL (Leave all bits in the command at 0). */
cmd = rank;
cmd |= SCH_DRAMINIT_CMD_EMRS1;
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
/* MRS; Reset DLL (Set memory address bit 8). */
cmd = rank;
cmd |= SCH_DRAMINIT_CMD_MRS;
cmd |= (SCH_JEDEC_DLLRESET << SCH_DRAMINIT_ADDR_OFFSET);
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
/* Precharge all. */
cmd = rank;
cmd |= SCH_DRAMINIT_CMD_PALL;
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
/* Issue 2 auto-refresh commands. */
cmd = rank;
cmd |= SCH_DRAMINIT_CMD_AREF;
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
/* MRS command including tCL, tWR, burst length (always 4). */
cmd = rank;
cmd |= (SCH_DRAMINIT_CMD_MRS + JEDEC_STATIC_PARAM); /* Static param */
temp = sysinfo->cl;
temp += TCL_LOW; /* Adjust for the TCL base. */
temp = temp << ((SCH_JEDEC_CL_OFFSET
+ SCH_DRAMINIT_ADDR_OFFSET)); /* Ready the CAS latency */
cmd |= temp;
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
/*
* Wait 200 clocks (max of 1us, so no need to delay).
* Issue EMRS(1):OCD default.
*/
cmd = rank;
cmd |= SCH_DRAMINIT_CMD_EMRS1;
cmd |= (SCH_JEDEC_OCD_DEFAULT << SCH_DRAMINIT_ADDR_OFFSET);
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
/* Issue EMRS(1): OCD cal. mode exit. */
cmd = rank;
cmd |= SCH_DRAMINIT_CMD_EMRS1;
cmd |= (SCH_JEDEC_DQS_DIS << SCH_DRAMINIT_ADDR_OFFSET);
sch_port_access_write_ram_cmd(SCH_OPCODE_DRAMINIT,
SCH_MSG_DUNIT_PORT, 0, cmd);
rank += SCH_DRAMINIT_RANK_MASK;
num_ranks--;
} while (num_ranks);
}
