static void serial_pxa_shutdown(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned long flags;
free_irq(up->port.irq, up);
/*
* Disable interrupts from this port
*/
up->ier = 0;
serial_out(up, UART_IER, 0);
spin_lock_irqsave(&up->port.lock, flags);
up->port.mctrl &= ~TIOCM_OUT2;
serial_pxa_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* Disable break condition and FIFOs
*/
serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR |
UART_FCR_CLEAR_XMIT);
serial_out(up, UART_FCR, 0);
}
static int serial_pxa_startup(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned long flags;
int retval;
up->mcr = 0;
/*
* Allocate the IRQ
*/
retval = request_irq(up->port.irq, serial_pxa_irq, 0, up->name, up);
if (retval)
return retval;
/*
* Clear the FIFO buffers and disable them.
* (they will be reenabled in set_termios())
*/
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
serial_out(up, UART_FCR, 0);
/*
* Clear the interrupt registers.
*/
(void) serial_in(up, UART_LSR);
(void) serial_in(up, UART_RX);
(void) serial_in(up, UART_IIR);
(void) serial_in(up, UART_MSR);
/*
* Now, initialize the UART
*/
serial_out(up, UART_LCR, UART_LCR_WLEN8);
spin_lock_irqsave(&up->port.lock, flags);
up->port.mctrl |= TIOCM_OUT2;
serial_pxa_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* Finally, enable interrupts. Note: Modem status interrupts
* are set via set_termios(), which will be occuring imminently
* anyway, so we don't enable them here.
*/
up->ier = UART_IER_RLSI | UART_IER_RDI | UART_IER_RTOIE | UART_IER_UUE;
serial_out(up, UART_IER, up->ier);
/*
* And clear the interrupt registers again for luck.
*/
(void) serial_in(up, UART_LSR);
(void) serial_in(up, UART_RX);
(void) serial_in(up, UART_IIR);
(void) serial_in(up, UART_MSR);
return 0;
}
static void
serial_pxa_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned char cval, fcr = 0;
unsigned long flags;
unsigned int baud, quot;
switch (termios->c_cflag & CSIZE) {
case CS5:
cval = UART_LCR_WLEN5;
break;
case CS6:
cval = UART_LCR_WLEN6;
break;
case CS7:
cval = UART_LCR_WLEN7;
break;
default:
case CS8:
cval = UART_LCR_WLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = uart_get_divisor(port, baud);
if ((up->port.uartclk / quot) < (2400 * 16))
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR1;
else if ((up->port.uartclk / quot) < (230400 * 16))
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR8;
else
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR32;
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
spin_lock_irqsave(&up->port.lock, flags);
/*
* Ensure the port will be enabled.
* This is required especially for serial console.
*/
up->ier |= IER_UUE;
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
/*
* Characters to ignore
*/
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
/*
* CTS flow control flag and modem status interrupts
*/
up->ier &= ~UART_IER_MSI;
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */
serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */
serial_out(up, UART_LCR, cval); /* reset DLAB */
up->lcr = cval; /* Save LCR */
serial_pxa_set_mctrl(&up->port, up->port.mctrl);
serial_out(up, UART_FCR, fcr);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static int serial_pxa_startup(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned long flags;
int retval;
if (port->line == 3) /* HWUART */
up->mcr |= UART_MCR_AFE;
else
up->mcr = 0;
up->port.uartclk = clk_get_rate(up->clk);
/*
* Allocate the IRQ
*/
retval = request_irq(up->port.irq, serial_pxa_irq, 0, up->name, up);
if (retval)
return retval;
/*
* Clear the FIFO buffers and disable them.
* (they will be reenabled in set_termios())
*/
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
serial_out(up, UART_FCR, 0);
/*
* Clear the interrupt registers.
*/
(void) serial_in(up, UART_LSR);
(void) serial_in(up, UART_RX);
(void) serial_in(up, UART_IIR);
(void) serial_in(up, UART_MSR);
/*
* Now, initialize the UART
*/
serial_out(up, UART_LCR, UART_LCR_WLEN8);
spin_lock_irqsave(&up->port.lock, flags);
up->port.mctrl |= TIOCM_OUT2;
serial_pxa_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* Finally, enable interrupts. Note: Modem status interrupts
* are set via set_termios(), which will be occurring imminently
* anyway, so we don't enable them here.
*/
if (up->dma_enable) {
pxa_uart_dma_init(up);
up->uart_dma.rx_stop = 0;
pxa_uart_receive_dma_start(up);
tasklet_init(&up->uart_dma.tklet, uart_task_action,
(unsigned long)up);
}
spin_lock_irqsave(&up->port.lock, flags);
if (up->dma_enable) {
up->ier = UART_IER_DMAE | UART_IER_UUE;
} else {
up->ier = UART_IER_RLSI | UART_IER_RDI |
UART_IER_RTOIE | UART_IER_UUE;
}
serial_out(up, UART_IER, up->ier);
spin_unlock_irqrestore(&up->port.lock, flags);
/*
* And clear the interrupt registers again for luck.
*/
(void) serial_in(up, UART_LSR);
(void) serial_in(up, UART_RX);
(void) serial_in(up, UART_IIR);
(void) serial_in(up, UART_MSR);
return 0;
}
static void
serial_pxa_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned char cval, fcr = 0;
unsigned long flags;
unsigned int baud, quot = 0;
unsigned int dll;
switch (termios->c_cflag & CSIZE) {
case CS5:
cval = UART_LCR_WLEN5;
break;
case CS6:
cval = UART_LCR_WLEN6;
break;
case CS7:
cval = UART_LCR_WLEN7;
break;
default:
case CS8:
cval = UART_LCR_WLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, 921600*16*4/16);
if (baud > 921600) {
port->uartclk = 921600*16*4; /* 58.9823MHz as the clk src */
if (B1500000 == (termios->c_cflag & B1500000))
quot = 2;
if (B3500000 == (termios->c_cflag & B3500000))
quot = 1;
if (quot == 0)
quot = uart_get_divisor(port, baud);
} else {
quot = uart_get_divisor(port, baud);
}
if (up->dma_enable) {
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR32 |
UART_FCR_PXA_TRAIL;
fcr &= ~UART_FCR_PXA_BUS32;
} else {
if ((up->port.uartclk / quot) < (2400 * 16))
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR1;
else if ((up->port.uartclk / quot) < (230400 * 16))
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR8;
else
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR32;
}
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
spin_lock_irqsave(&up->port.lock, flags);
if (baud > 921600)
up->ier |= UART_IER_HSE;
else
up->ier &= ~UART_IER_HSE;
/*
* Ensure the port will be enabled.
* This is required especially for serial console.
*/
up->ier |= UART_IER_UUE;
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
/*
* Characters to ignore
*/
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
/*
* CTS flow control flag and modem status interrupts
*/
if (!up->dma_enable) {
/* Don't enable modem status interrupt if DMA is enabled.
* Inherited from the old code.
* Please also refer to serial_pxa_enable_ms().
*/
up->ier &= ~UART_IER_MSI;
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
}
serial_out(up, UART_IER, up->ier);
if (termios->c_cflag & CRTSCTS)
up->mcr |= UART_MCR_AFE;
else
up->mcr &= ~UART_MCR_AFE;
serial_out(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */
serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */
/*
* work around Errata #75 according to Intel(R) PXA27x Processor Family
* Specification Update (Nov 2005)
*/
dll = serial_in(up, UART_DLL);
WARN_ON(dll != (quot & 0xff));
serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */
serial_out(up, UART_LCR, cval); /* reset DLAB */
up->lcr = cval; /* Save LCR */
serial_pxa_set_mctrl(&up->port, up->port.mctrl);
serial_out(up, UART_FCR, fcr);
spin_unlock_irqrestore(&up->port.lock, flags);
}
