C++ (Cpp) set_sdc_power_ctrl примеры использования

Пример #1

Файл: init.c Проект: cancro-dev/bootloader_lk

void target_sdc_init(void)
{
	struct mmc_config_data config;
	struct mmc_device *tmpdev;

	target_sdc_pre_init_actions();

	config.bus_width = DATA_BUS_WIDTH_8BIT;
	config.max_clk_rate = MMC_CLK_200MHZ;

	/* Try slot 1*/
	config.slot = 1;
	config.sdhc_base = mmc_sdhci_base[config.slot - 1];
	config.pwrctl_base = mmc_pwrctl_base[config.slot - 1];
	config.pwr_irq     = mmc_sdc_pwrctl_irq[config.slot - 1];
	config.hs400_support = 0;

	/* Set drive strength & pull ctrl values */
	set_sdc_power_ctrl(config.slot);

	if (!(dev = mmc_init(&config)))
	{
		dprintf(CRITICAL, "mmc1 init failed!");
	}

	/* Try slot 2 */
	config.slot = 2;
	config.sdhc_base = mmc_sdhci_base[config.slot - 1];
	config.pwrctl_base = mmc_pwrctl_base[config.slot - 1];
	config.pwr_irq     = mmc_sdc_pwrctl_irq[config.slot - 1];

	/* Set drive strength & pull ctrl values */
	set_sdc_power_ctrl(config.slot);

	if (!(tmpdev = mmc_init(&config)))
	{
		dprintf(CRITICAL, "mmc2 init failed!");
	}
	else if(!dev)
		dev = tmpdev;

	/* we need at least one mmc device */
	ASSERT(dev);

	/* MMC initialization is complete, read the partition table info */
	if (partition_read_table())
	{
		dprintf(CRITICAL, "Error reading the partition table info\n");
		ASSERT(0);
	}
}

Пример #2

Файл: init.c Проект: BorqsIndia/bootable-bootloader-lk

void target_sdc_init()
{
	struct mmc_config_data config;

	/* Set drive strength & pull ctrl values */
	set_sdc_power_ctrl();

	/* Try slot 1*/
	config.slot          = 1;
	config.bus_width     = DATA_BUS_WIDTH_8BIT;
	config.max_clk_rate  = MMC_CLK_192MHZ;
	config.sdhc_base     = mmc_sdhci_base[config.slot - 1];
	config.pwrctl_base   = mmc_pwrctl_base[config.slot - 1];
	config.pwr_irq       = mmc_sdc_pwrctl_irq[config.slot - 1];
	config.hs400_support = 1;

	if (!(dev = mmc_init(&config))) {
	/* Try slot 2 */
		config.slot          = 2;
		config.max_clk_rate  = MMC_CLK_200MHZ;
		config.sdhc_base     = mmc_sdhci_base[config.slot - 1];
		config.pwrctl_base   = mmc_pwrctl_base[config.slot - 1];
		config.pwr_irq       = mmc_sdc_pwrctl_irq[config.slot - 1];
		config.hs400_support = 0;

		if (!(dev = mmc_init(&config))) {
			dprintf(CRITICAL, "mmc init failed!");
			ASSERT(0);
		}
	}
}

Пример #3

Файл: init.c Проект: nx511j-multirom/bootloader_lk

void target_init(void)
{
	dprintf(INFO, "target_init()\n");

	spmi_init(PMIC_ARB_CHANNEL_NUM, PMIC_ARB_OWNER_ID);

	/* Save PM8941 version info. */
	pmic_ver = pm8x41_get_pmic_rev();

	target_keystatus();

	if (target_use_signed_kernel())
		target_crypto_init_params();

	/*
	 * Set drive strength & pull ctrl for
	 * emmc
	 */
	set_sdc_power_ctrl();

#if MMC_SDHCI_SUPPORT
	target_mmc_sdhci_init();
#else
	target_mmc_mci_init();
#endif
}

Пример #4

Файл: init.c Проект: GoldRenard/android_bootable_bootloader_lk-shellr

void target_init(void)
{
	dprintf(INFO, "target_init()\n");

	spmi_init(PMIC_ARB_CHANNEL_NUM, PMIC_ARB_OWNER_ID);

	/* Save PM8941 version info. */
	pmic_ver = pm8x41_get_pmic_rev();

	target_keystatus();

	if (target_use_signed_kernel())
		target_crypto_init_params();
	/* Display splash screen if enabled */
#if DISPLAY_SPLASH_SCREEN
	dprintf(INFO, "Display Init: Start\n");
	if (board_hardware_subtype() != HW_PLATFORM_SUBTYPE_CDP_INTERPOSER)
	{
		display_init();
	}
	dprintf(INFO, "Display Init: Done\n");
#endif

	/*
	 * Set drive strength & pull ctrl for
	 * emmc
	 */
	set_sdc_power_ctrl();

#if MMC_SDHCI_SUPPORT
	target_mmc_sdhci_init();
#else
	target_mmc_mci_init();
#endif
}

Пример #5

Файл: init.c Проект: KortanZ/linux

void target_init(void)
{
	dprintf(INFO, "target_init()\n");

	target_keystatus();

	if (target_use_signed_kernel())
		target_crypto_init_params();

	/*
	 * Set drive strength & pull ctrl for
	 * emmc
	 */
	set_sdc_power_ctrl();

#if MMC_SDHCI_SUPPORT
	target_mmc_sdhci_init();
#else
	target_mmc_mci_init();
#endif
}

Пример #6

Файл: init.c Проект: detule/lk-g2-spr

void target_sdc_init()
{
	struct mmc_config_data config = {0};

	/*
	 * Set drive strength & pull ctrl for emmc
	 */
	set_sdc_power_ctrl();

	config.bus_width = DATA_BUS_WIDTH_8BIT;
	config.max_clk_rate = MMC_CLK_200MHZ;

	/* Trying Slot 1*/
	config.slot = 1;
	config.sdhc_base = mmc_sdhci_base[config.slot - 1];
	config.pwrctl_base = mmc_pwrctl_base[config.slot - 1];
	config.pwr_irq     = mmc_sdc_pwrctl_irq[config.slot - 1];

	if (!(dev = mmc_init(&config)))
	{
		/* Trying Slot 2 next */
		config.slot = 2;
		config.sdhc_base = mmc_sdhci_base[config.slot - 1];
		config.pwrctl_base = mmc_pwrctl_base[config.slot - 1];
		config.pwr_irq     = mmc_sdc_pwrctl_irq[config.slot - 1];

		if (!(dev = mmc_init(&config))) {
			dprintf(CRITICAL, "mmc init failed!");
			ASSERT(0);
		}
	}

	/*
	 * MMC initialization is complete, read the partition table info
	 */
	if (partition_read_table()) {
		dprintf(CRITICAL, "Error reading the partition table info\n");
		ASSERT(0);
	}
}

Пример #7

Файл: init.c Проект: daxgr/android_bootable_bootloader_lk

void target_init(void)
{
	dprintf(INFO, "target_init()\n");

	spmi_init(PMIC_ARB_CHANNEL_NUM, PMIC_ARB_OWNER_ID);

	/* Save PM8941 version info. */
	pmic_ver = pm8x41_get_pmic_rev();

	target_keystatus();

	if (target_use_signed_kernel())
		target_crypto_init_params();
	/* Display splash screen if enabled */
#if DISPLAY_SPLASH_SCREEN
	dprintf(INFO, "Display Init: Start\n");
	display_init();
	dprintf(INFO, "Display Init: Done\n");
#endif

	/*
	 * Set drive strength & pull ctrl for
	 * emmc
	 */
	set_sdc_power_ctrl();

#if MMC_SDHCI_SUPPORT
	target_mmc_sdhci_init();
#else
	target_mmc_mci_init();
#endif

	/*
	 * MMC initialization is complete, read the partition table info
	 */
	if (partition_read_table()) {
		dprintf(CRITICAL, "Error reading the partition table info\n");
		ASSERT(0);
	}
}