void up_irqinitialize(void)
{
uint32_t regaddr;
int num_priority_registers;
/* Disable all interrupts */
putreg32(0, NVIC_IRQ0_31_ENABLE);
putreg32(0, NVIC_IRQ32_63_ENABLE);
/* The standard location for the vector table is at the beginning of FLASH
* at address 0x0800:0000. If we are using the STMicro DFU bootloader, then
* the vector table will be offset to a different location in FLASH and we
* will need to set the NVIC vector location to this alternative location.
*/
#ifdef CONFIG_STM32_DFU
putreg32((uint32_t)stm32_vectors, NVIC_VECTAB);
#endif
/* Set all interrupts (and exceptions) to the default priority */
putreg32(DEFPRIORITY32, NVIC_SYSH4_7_PRIORITY);
putreg32(DEFPRIORITY32, NVIC_SYSH8_11_PRIORITY);
putreg32(DEFPRIORITY32, NVIC_SYSH12_15_PRIORITY);
/* The NVIC ICTR register (bits 0-4) holds the number of of interrupt
* lines that the NVIC supports:
*
* 0 -> 32 interrupt lines, 8 priority registers
* 1 -> 64 " " " ", 16 priority registers
* 2 -> 96 " " " ", 32 priority registers
* ...
*/
num_priority_registers = (getreg32(NVIC_ICTR) + 1) * 8;
/* Now set all of the interrupt lines to the default priority */
regaddr = NVIC_IRQ0_3_PRIORITY;
while (num_priority_registers--)
{
putreg32(DEFPRIORITY32, regaddr);
regaddr += 4;
}
/* currents_regs is non-NULL only while processing an interrupt */
current_regs = NULL;
/* Attach the SVCall and Hard Fault exception handlers. The SVCall
* exception is used for performing context switches; The Hard Fault
* must also be caught because a SVCall may show up as a Hard Fault
* under certain conditions.
*/
irq_attach(STM32_IRQ_SVCALL, up_svcall);
irq_attach(STM32_IRQ_HARDFAULT, up_hardfault);
/* Set the priority of the SVCall interrupt */
#ifdef CONFIG_ARCH_IRQPRIO
/* up_prioritize_irq(STM32_IRQ_PENDSV, NVIC_SYSH_PRIORITY_MIN); */
#endif
#ifdef CONFIG_ARMV7M_USEBASEPRI
stm32_prioritize_syscall(NVIC_SYSH_SVCALL_PRIORITY);
#endif
/* If the MPU is enabled, then attach and enable the Memory Management
* Fault handler.
*/
#ifdef CONFIG_ARMV7M_MPU
irq_attach(STM32_IRQ_MEMFAULT, up_memfault);
up_enable_irq(STM32_IRQ_MEMFAULT);
#endif
/* Attach all other processor exceptions (except reset and sys tick) */
#ifdef CONFIG_DEBUG
irq_attach(STM32_IRQ_NMI, stm32_nmi);
#ifndef CONFIG_ARMV7M_MPU
irq_attach(STM32_IRQ_MEMFAULT, up_memfault);
#endif
irq_attach(STM32_IRQ_BUSFAULT, stm32_busfault);
irq_attach(STM32_IRQ_USAGEFAULT, stm32_usagefault);
irq_attach(STM32_IRQ_PENDSV, stm32_pendsv);
irq_attach(STM32_IRQ_DBGMONITOR, stm32_dbgmonitor);
irq_attach(STM32_IRQ_RESERVED, stm32_reserved);
#endif
stm32_dumpnvic("initial", NR_IRQS);
#ifndef CONFIG_SUPPRESS_INTERRUPTS
/* And finally, enable interrupts */
irqenable();
#endif
}
void up_irqinitialize(void)
{
uintptr_t regaddr;
#if defined(CONFIG_DEBUG_SYMBOLS) && !defined(CONFIG_ARMV7M_USEBASEPRI)
uint32_t regval;
#endif
int nintlines;
int i;
/* The NVIC ICTR register (bits 0-4) holds the number of of interrupt
* lines that the NVIC supports, defined in groups of 32. That is,
* the total number of interrupt lines is up to (32*(INTLINESNUM+1)).
*
* 0 -> 32 interrupt lines, 1 enable register, 8 priority registers
* 1 -> 64 " " " ", 2 enable registers, 16 priority registers
* 2 -> 96 " " " ", 3 enable regsiters, 24 priority registers
* ...
*/
nintlines = (getreg32(NVIC_ICTR) & NVIC_ICTR_INTLINESNUM_MASK) + 1;
/* Disable all interrupts. There are nintlines interrupt enable
* registers.
*/
for (i = nintlines, regaddr = NVIC_IRQ0_31_CLEAR;
i > 0;
i--, regaddr += 4)
{
putreg32(0xffffffff, regaddr);
}
/* Make sure that we are using the correct vector table. The default
* vector address is 0x0000:0000 but if we are executing code that is
* positioned in SRAM or in external FLASH, then we may need to reset
* the interrupt vector so that it refers to the table in SRAM or in
* external FLASH.
*/
putreg32((uint32_t)_vectors, NVIC_VECTAB);
#ifdef CONFIG_ARCH_RAMVECTORS
/* If CONFIG_ARCH_RAMVECTORS is defined, then we are using a RAM-based
* vector table that requires special initialization.
*/
up_ramvec_initialize();
#endif
/* Set all interrupts (and exceptions) to the default priority */
putreg32(DEFPRIORITY32, NVIC_SYSH4_7_PRIORITY);
putreg32(DEFPRIORITY32, NVIC_SYSH8_11_PRIORITY);
putreg32(DEFPRIORITY32, NVIC_SYSH12_15_PRIORITY);
/* Now set all of the interrupt lines to the default priority. There are
* nintlines * 8 priority registers.
*/
for (i = (nintlines << 3), regaddr = NVIC_IRQ0_3_PRIORITY;
i > 0;
i--, regaddr += 4)
{
putreg32(DEFPRIORITY32, regaddr);
}
/* currents_regs is non-NULL only while processing an interrupt */
CURRENT_REGS = NULL;
/* Attach the SVCall and Hard Fault exception handlers. The SVCall
* exception is used for performing context switches; The Hard Fault
* must also be caught because a SVCall may show up as a Hard Fault
* under certain conditions.
*/
irq_attach(STM32_IRQ_SVCALL, up_svcall, NULL);
irq_attach(STM32_IRQ_HARDFAULT, up_hardfault, NULL);
/* Set the priority of the SVCall interrupt */
#ifdef CONFIG_ARCH_IRQPRIO
/* up_prioritize_irq(STM32_IRQ_PENDSV, NVIC_SYSH_PRIORITY_MIN); */
#endif
#ifdef CONFIG_ARMV7M_USEBASEPRI
stm32_prioritize_syscall(NVIC_SYSH_SVCALL_PRIORITY);
#endif
/* If the MPU is enabled, then attach and enable the Memory Management
* Fault handler.
*/
#ifdef CONFIG_ARM_MPU
irq_attach(STM32_IRQ_MEMFAULT, up_memfault, NULL);
up_enable_irq(STM32_IRQ_MEMFAULT);
#endif
/* Attach all other processor exceptions (except reset and sys tick) */
#ifdef CONFIG_DEBUG_FEATURES
irq_attach(STM32_IRQ_NMI, stm32_nmi, NULL);
#ifndef CONFIG_ARM_MPU
irq_attach(STM32_IRQ_MEMFAULT, up_memfault, NULL);
#endif
irq_attach(STM32_IRQ_BUSFAULT, stm32_busfault, NULL);
irq_attach(STM32_IRQ_USAGEFAULT, stm32_usagefault, NULL);
irq_attach(STM32_IRQ_PENDSV, stm32_pendsv, NULL);
irq_attach(STM32_IRQ_DBGMONITOR, stm32_dbgmonitor, NULL);
irq_attach(STM32_IRQ_RESERVED, stm32_reserved, NULL);
#endif
stm32_dumpnvic("initial", STM32_IRQ_NIRQS);
/* If a debugger is connected, try to prevent it from catching hardfaults.
* If CONFIG_ARMV7M_USEBASEPRI, no hardfaults are expected in normal
* operation.
*/
#if defined(CONFIG_DEBUG_SYMBOLS) && !defined(CONFIG_ARMV7M_USEBASEPRI)
regval = getreg32(NVIC_DEMCR);
regval &= ~NVIC_DEMCR_VCHARDERR;
putreg32(regval, NVIC_DEMCR);
#endif
#ifndef CONFIG_SUPPRESS_INTERRUPTS
/* Initialize logic to support a second level of interrupt decoding for
* GPIO pins.
*/
#ifdef CONFIG_STM32H7_GPIO_IRQ
stm32_gpioirqinitialize();
#endif
/* And finally, enable interrupts */
up_irq_enable();
#endif
}
