/*
* Miscellaneous late-boot configurations
*
* If a VSC7385 microcode image is present, then upload it.
*/
int misc_init_r(void)
{
#ifdef CONFIG_MPC8XXX_SPI
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
sysconf83xx_t *sysconf = &immr->sysconf;
/*
* Set proper bits in SICRH to allow SPI on header J8
*
* NOTE: this breaks the TSEC2 interface, attached to the Vitesse
* switch. The pinmux configuration does not have a fine enough
* granularity to support both simultaneously.
*/
clrsetbits_be32(&sysconf->sicrh, SICRH_GPIO_A_TSEC2, SICRH_GPIO_A_GPIO);
puts("WARNING: SPI enabled, TSEC2 support is broken\n");
/* Set header J8 SPI chip select output, disabled */
setbits_be32(&immr->gpio[0].dir, SPI_CS_MASK);
setbits_be32(&immr->gpio[0].dat, SPI_CS_MASK);
#endif
#ifdef CONFIG_VSC7385_IMAGE
if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
CONFIG_VSC7385_IMAGE_SIZE)) {
puts("Failure uploading VSC7385 microcode.\n");
return 1;
}
#endif
return 0;
}
/*
* Miscellaneous late-boot configurations
*
* If a VSC7385 microcode image is present, then upload it.
*/
int misc_init_r(void)
{
#ifdef CONFIG_VSC7385_IMAGE
if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
CONFIG_VSC7385_IMAGE_SIZE)) {
puts("Failure uploading VSC7385 microcode.\n");
return 1;
}
#endif
return 0;
}
int board_eth_init(bd_t *bis)
{
struct fsl_pq_mdio_info mdio_info;
struct tsec_info_struct tsec_info[4];
int num = 0;
char *tmp;
unsigned int vscfw_addr;
#ifdef CONFIG_TSEC1
SET_STD_TSEC_INFO(tsec_info[num], 1);
num++;
#endif
#ifdef CONFIG_TSEC2
SET_STD_TSEC_INFO(tsec_info[num], 2);
num++;
#endif
#ifdef CONFIG_TSEC3
SET_STD_TSEC_INFO(tsec_info[num], 3);
if (is_serdes_configured(SGMII_TSEC3)) {
puts("eTSEC3 is in sgmii mode.\n");
tsec_info[num].flags |= TSEC_SGMII;
}
num++;
#endif
if (!num) {
printf("No TSECs initialized\n");
return 0;
}
#ifdef CONFIG_VSC7385_ENET
/* If a VSC7385 microcode image is present, then upload it. */
if ((tmp = getenv ("vscfw_addr")) != NULL) {
vscfw_addr = simple_strtoul (tmp, NULL, 16);
printf("uploading VSC7385 microcode from %x\n", vscfw_addr);
if (vsc7385_upload_firmware((void *) vscfw_addr,
CONFIG_VSC7385_IMAGE_SIZE))
puts("Failure uploading VSC7385 microcode.\n");
} else
puts("No address specified for VSC7385 microcode.\n");
#endif
mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
mdio_info.name = DEFAULT_MII_NAME;
fsl_pq_mdio_init(bis, &mdio_info);
tsec_eth_init(bis, tsec_info, num);
return pci_eth_init(bis);
}
int board_eth_init(bd_t *bis)
{
struct tsec_info_struct tsec_info[4];
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
int num = 0;
char *tmp;
unsigned int vscfw_addr;
#ifdef CONFIG_TSEC1
SET_STD_TSEC_INFO(tsec_info[num], 1);
num++;
#endif
#ifdef CONFIG_TSEC2
SET_STD_TSEC_INFO(tsec_info[num], 2);
num++;
#endif
#ifdef CONFIG_TSEC3
SET_STD_TSEC_INFO(tsec_info[num], 3);
if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII3_DIS))
tsec_info[num].flags |= TSEC_SGMII;
num++;
#endif
if (!num) {
printf("No TSECs initialized\n");
return 0;
}
#ifdef CONFIG_VSC7385_ENET
/* If a VSC7385 microcode image is present, then upload it. */
if ((tmp = getenv ("vscfw_addr")) != NULL) {
vscfw_addr = simple_strtoul (tmp, NULL, 16);
printf("uploading VSC7385 microcode from %x\n", vscfw_addr);
if (vsc7385_upload_firmware((void *) vscfw_addr,
CONFIG_VSC7385_IMAGE_SIZE))
puts("Failure uploading VSC7385 microcode.\n");
} else
puts("No address specified for VSC7385 microcode.\n");
#endif
tsec_eth_init(bis, tsec_info, num);
return pci_eth_init(bis);
}
int board_eth_init(bd_t *bis)
{
struct fsl_pq_mdio_info mdio_info;
struct tsec_info_struct tsec_info[4];
ccsr_gur_t *gur __attribute__((unused)) =
(void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
int num = 0;
#ifdef CONFIG_VSC7385_ENET
char *tmp;
unsigned int vscfw_addr;
#endif
#ifdef CONFIG_TSEC1
SET_STD_TSEC_INFO(tsec_info[num], 1);
num++;
#endif
#ifdef CONFIG_TSEC2
SET_STD_TSEC_INFO(tsec_info[num], 2);
if (is_serdes_configured(SGMII_TSEC2)) {
printf("eTSEC2 is in sgmii mode.\n");
tsec_info[num].flags |= TSEC_SGMII;
}
num++;
#endif
#ifdef CONFIG_TSEC3
SET_STD_TSEC_INFO(tsec_info[num], 3);
num++;
#endif
if (!num) {
printf("No TSECs initialized\n");
return 0;
}
#ifdef CONFIG_VSC7385_ENET
/* If a VSC7385 microcode image is present, then upload it. */
tmp = env_get("vscfw_addr");
if (tmp) {
vscfw_addr = simple_strtoul(tmp, NULL, 16);
printf("uploading VSC7385 microcode from %x\n", vscfw_addr);
if (vsc7385_upload_firmware((void *) vscfw_addr,
CONFIG_VSC7385_IMAGE_SIZE))
puts("Failure uploading VSC7385 microcode.\n");
} else
puts("No address specified for VSC7385 microcode.\n");
#endif
mdio_info.regs = TSEC_GET_MDIO_REGS_BASE(1);
mdio_info.name = DEFAULT_MII_NAME;
fsl_pq_mdio_init(bis, &mdio_info);
tsec_eth_init(bis, tsec_info, num);
#if defined(CONFIG_UEC_ETH)
/* QE0 and QE3 need to be exposed for UCC1 and UCC5 Eth mode */
setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE0);
setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE3);
uec_standard_init(bis);
#endif
return pci_eth_init(bis);
}