/* that function will returns :
1) return : Host gpio interrupt number per customer platform
2) irq_flags_ptr : Type of Host interrupt as Level or Edge
NOTE :
Customer should check his platform definitions
and hist Host Interrupt spec
to figure out the proper setting for his platform.
BRCM provides just reference settings as example.
*/
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq = 0;
#if defined(CUSTOM_OOB_GPIO_NUM)
if (dhd_oob_gpio_num < 0) {
dhd_oob_gpio_num = CUSTOM_OOB_GPIO_NUM;
}
#endif
if (dhd_oob_gpio_num < 0) {
WL_ERROR(("%s: ERROR customer specific Host GPIO is NOT defined \n",
__FUNCTION__));
return (dhd_oob_gpio_num);
}
WL_ERROR(("%s: customer specific Host GPIO number is (%d), flag=0x%X\n",
__FUNCTION__, dhd_oob_gpio_num, (unsigned int)*irq_flags_ptr));
#ifdef CONFIG_MACH_SAMSUNG_P3
host_oob_irq = gpio_to_irq(dhd_oob_gpio_num);
#elif defined(SYSLSI_SPECIFIC)
host_oob_irq = dhd_oob_gpio_num;
#elif defined(CONFIG_WIFI_CONTROL_FUNC)
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
#endif
return (host_oob_irq);
}
/* This function will return:
* 1) return : Host gpio interrupt number per customer platform
* 2) irq_flags_ptr : Type of Host interrupt as Level or Edge
*
* NOTE :
* Customer should check his platform definitions
* and his Host Interrupt spec
* to figure out the proper setting for his platform.
* Broadcom provides just reference settings as example.
*
*/
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq = 0;
#if defined(CUSTOMER_HW2) || defined(CUSTOMER_HW_SAMSUNG)
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
#else
#if defined(CUSTOM_OOB_GPIO_NUM)
if (dhd_oob_gpio_num < 0) {
dhd_oob_gpio_num = CUSTOM_OOB_GPIO_NUM;
}
#endif /* CUSTOMER_OOB_GPIO_NUM */
if (dhd_oob_gpio_num < 0) {
WL_ERROR(("%s: ERROR customer specific Host GPIO is NOT defined \n",
__FUNCTION__));
return (dhd_oob_gpio_num);
}
WL_ERROR(("%s: customer specific Host GPIO number is (%d)\n",
__FUNCTION__, dhd_oob_gpio_num));
#if defined CUSTOMER_HW
host_oob_irq = MSM_GPIO_TO_INT(dhd_oob_gpio_num);
#elif defined CUSTOMER_HW3
gpio_request(dhd_oob_gpio_num, "oob irq");
host_oob_irq = gpio_to_irq(dhd_oob_gpio_num);
gpio_direction_input(dhd_oob_gpio_num);
#endif /* CUSTOMER_HW */
#endif /* CUSTOMER_HW2 || CUSTOMER_HW_SAMSUNG */
return (host_oob_irq);
}
/* This function will return:
* 1) return : Host gpio interrupt number per customer platform
* 2) irq_flags_ptr : Type of Host interrupt as Level or Edge
*
* NOTE :
* Customer should check his platform definitions
* and his Host Interrupt spec
* to figure out the proper setting for his platform.
* Broadcom provides just reference settings as example.
*
*/
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq = 0;
#if defined(CUSTOMER_HW4)
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
#else
#if defined(CUSTOM_OOB_GPIO_NUM)
if (dhd_oob_gpio_num < 0) {
dhd_oob_gpio_num = CUSTOM_OOB_GPIO_NUM;
}
#endif /* CUSTOMER_OOB_GPIO_NUM */
if (dhd_oob_gpio_num < 0) {
WL_ERROR(("%s: ERROR customer specific Host GPIO is NOT defined \n",
__FUNCTION__));
return (dhd_oob_gpio_num);
}
WL_ERROR(("%s: customer specific Host GPIO number is (%d)\n",
__FUNCTION__, dhd_oob_gpio_num));
#endif
return (host_oob_irq);
}
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq;
#ifdef CUSTOMER_HW2
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
#else
#if defined(CUSTOM_OOB_GPIO_NUM)
if (dhd_oob_gpio_num < 0) {
dhd_oob_gpio_num = CUSTOM_OOB_GPIO_NUM;
}
#endif
*irq_flags_ptr = IRQF_TRIGGER_FALLING;
if (dhd_oob_gpio_num < 0) {
WL_ERROR(("%s: ERROR customer specific Host GPIO is NOT defined \n",
__FUNCTION__));
return (dhd_oob_gpio_num);
}
WL_ERROR(("%s: customer specific Host GPIO number is (%d)\n",
__FUNCTION__, dhd_oob_gpio_num));
host_oob_irq = sdioh_mmc_irq(dhd_oob_gpio_num);
#endif
return (host_oob_irq);
}
/* that function will returns :
1) return : Host gpio interrupt number per customer platform
2) irq_flags_ptr : Type of Host interrupt as Level or Edge
NOTE :
Customer should check his platform definitions
and hist Host Interrupt spec
to figure out the proper setting for his platform.
BRCM provides just reference settings as example.
*/
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq = 0;
printf("%s:%d\n",__FUNCTION__,__LINE__);
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
WL_ERROR(("%s: customer specific Host GPIO number is (%d)\n",
__FUNCTION__, host_oob_irq));
return (host_oob_irq);
}
/* This function will return:
* 1) return : Host gpio interrupt number per customer platform
* 2) irq_flags_ptr : Type of Host interrupt as Level or Edge
*
* NOTE :
* Customer should check his platform definitions
* and his Host Interrupt spec
* to figure out the proper setting for his platform.
* Broadcom provides just reference settings as example.
*
*/
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq = 0;
#ifdef CONFIG_WIFI_CONTROL_EXPORT
host_oob_irq = bcm_wlan_get_irq();
#endif /* CONFIG_WIFI_CONTROL_EXPORT */
#ifdef CONFIG_WIFI_CONTROL_FUNC
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
#endif /* CONFIG_WIFI_CONTROL_FUNC */
return (host_oob_irq);
}
/* This function will return:
* 1) return : Host gpio interrupt number per customer platform
* 2) irq_flags_ptr : Type of Host interrupt as Level or Edge
*
* NOTE :
* Customer should check his platform definitions
* and his Host Interrupt spec
* to figure out the proper setting for his platform.
* Broadcom provides just reference settings as example.
*
*/
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq = 0;
int ret;
#if defined(CUSTOMER_HW2)
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
#elif defined(NUFRONT_OOB)
printk("GPIO(WL_HOST_WAKE_UP) = %d\n", 0);
ret = gpio_request(0, "WL_HOST_WAKEUP");
/* use wakeup domain GPIO3 LOW_BAT_INIT instead */
//ret = gpio_request(3, "WL_HOST_WAKEUP");
if(ret < 0)
printk(KERN_ERR "request WL_HOST_WAKEUP failed\n");
host_oob_irq = gpio_to_irq(0);
gpio_direction_input(0);
printk("host_oob_irq: %d \r\n", host_oob_irq);
// host_oob_irq = bcm_wlan_get_oob_irq();
#else
#if defined(CUSTOM_OOB_GPIO_NUM)
if (dhd_oob_gpio_num < 0) {
dhd_oob_gpio_num = CUSTOM_OOB_GPIO_NUM;
}
#endif /* CUSTOMER_OOB_GPIO_NUM */
if (dhd_oob_gpio_num < 0) {
WL_ERROR(("%s: ERROR customer specific Host GPIO is NOT defined \n",
__FUNCTION__));
return (dhd_oob_gpio_num);
}
WL_ERROR(("%s: customer specific Host GPIO number is (%d)\n",
__FUNCTION__, dhd_oob_gpio_num));
#if defined CUSTOMER_HW
host_oob_irq = MSM_GPIO_TO_INT(dhd_oob_gpio_num);
#elif defined CUSTOMER_HW3
gpio_request(dhd_oob_gpio_num, "oob irq");
host_oob_irq = gpio_to_irq(dhd_oob_gpio_num);
gpio_direction_input(dhd_oob_gpio_num);
#endif /* CUSTOMER_HW */
#endif
return (host_oob_irq);
}
/* This function will return:
* 1) return : Host gpio interrupt number per customer platform
* 2) irq_flags_ptr : Type of Host interrupt as Level or Edge
*
* NOTE :
* Customer should check his platform definitions
* and his Host Interrupt spec
* to figure out the proper setting for his platform.
* Broadcom provides just reference settings as example.
*
*/
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq = 0;
#if defined(CUSTOMER_HW2)
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
#if defined(BOARD_INTEL)
if (!wifi_irq_is_fastirq()) {
if (gpio_request(host_oob_irq, "bcm43xx_irq") < 0) {
WL_ERROR(("%s: Error on gpio_request bcm43xx_irq: %d\n", __func__, host_oob_irq));
return 1;
}
if (gpio_direction_input(host_oob_irq) < 0) {
WL_ERROR(("%s: Error on gpio_direction_input\n", __func__));
return 1;
}
if (gpio_set_debounce(host_oob_irq, 0) < 0)
WL_ERROR(("%s: Error on gpio_set_debounce\n", __func__));
host_oob_irq = gpio_to_irq(host_oob_irq);
}
#endif /* BOARD_INTEL */
#else
#if defined(CUSTOM_OOB_GPIO_NUM)
if (dhd_oob_gpio_num < 0) {
dhd_oob_gpio_num = CUSTOM_OOB_GPIO_NUM;
}
#endif /* CUSTOMER_OOB_GPIO_NUM */
if (dhd_oob_gpio_num < 0) {
WL_ERROR(("%s: ERROR customer specific Host GPIO is NOT defined \n",
__FUNCTION__));
return (dhd_oob_gpio_num);
}
WL_ERROR(("%s: customer specific Host GPIO number is (%d)\n",
__FUNCTION__, dhd_oob_gpio_num));
#if defined CUSTOMER_HW
host_oob_irq = MSM_GPIO_TO_INT(dhd_oob_gpio_num);
#elif defined CUSTOMER_HW3
gpio_request(dhd_oob_gpio_num, "oob irq");
host_oob_irq = gpio_to_irq(dhd_oob_gpio_num);
gpio_direction_input(dhd_oob_gpio_num);
#endif /* CUSTOMER_HW */
#endif
return (host_oob_irq);
}
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq = 0;
//&*&*&*JohWan1 mod BCM4329 OOB support
#if 0
#ifdef CUSTOMER_HW2
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
#else /* for NOT CUSTOMER_HW2 */
#if defined(CUSTOM_OOB_GPIO_NUM)
if (dhd_oob_gpio_num < 0) {
dhd_oob_gpio_num = CUSTOM_OOB_GPIO_NUM;
}
#endif
if (dhd_oob_gpio_num < 0) {
WL_ERROR(("%s: ERROR customer specific Host GPIO is NOT defined \n",
__FUNCTION__));
return (dhd_oob_gpio_num);
}
WL_ERROR(("%s: customer specific Host GPIO number is (%d)\n",
__FUNCTION__, dhd_oob_gpio_num));
#if defined CUSTOMER_HW
host_oob_irq = MSM_GPIO_TO_INT(dhd_oob_gpio_num);
#elif defined CUSTOMER_HW3
gpio_request(dhd_oob_gpio_num, "oob irq");
host_oob_irq = gpio_to_irq(dhd_oob_gpio_num);
gpio_direction_input(dhd_oob_gpio_num);
#endif /* CUSTOMER_HW */
#endif /* CUSTOMER_HW2 */
#else //if 0
{
//BOARD_ID_EVT3
gpio_direction_input(CUSTOM_OOB_GPIO_NUM);
host_oob_irq = OMAP_GPIO_IRQ(CUSTOM_OOB_GPIO_NUM);
printk("dhd_customer_oob_irq_map irg = %d \n",host_oob_irq);
}
#endif //if 0
//&*&*&*JohWan2 mod BCM4329 OOB support
return (host_oob_irq);
}
int dhd_customer_oob_irq_unmap(void)
{
#if defined(CUSTOMER_HW2) || defined(CUSTOMER_HW4)
int host_oob_irq = 0;
long unsigned int irq_flags_ptr;
host_oob_irq = wifi_get_irq_number(&irq_flags_ptr);
if (host_oob_irq < 0)
WL_ERROR(("%s: wifi_get_irq_number returned %d\n",
__func__, host_oob_irq));
else {
if (gpio_set_debounce(host_oob_irq, 1) < 0)
WL_ERROR(("%s: Error on gpio_set_debounce\n",
__func__));
gpio_free(host_oob_irq);
}
#endif
return 0;
}
/* This function will return:
* 1) return : Host gpio interrupt number per customer platform
* 2) irq_flags_ptr : Type of Host interrupt as Level or Edge
*
* NOTE :
* Customer should check his platform definitions
* and his Host Interrupt spec
* to figure out the proper setting for his platform.
* Broadcom provides just reference settings as example.
*
*/
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq = 0;
#ifdef CUSTOMER_HW2
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
#elif defined(HARDKERNEL_OOB)
printk("GPIO(WL_HOST_WAKE) = EXYNOS4_GPX0(7) = %d\n", EXYNOS4_GPX0(7));
host_oob_irq = gpio_to_irq(EXYNOS4_GPX0(7));
gpio_direction_input(EXYNOS4_GPX0(7));
printk("host_oob_irq: %d \r\n", host_oob_irq);
#else
#if defined(CUSTOM_OOB_GPIO_NUM)
if (dhd_oob_gpio_num < 0) {
dhd_oob_gpio_num = CUSTOM_OOB_GPIO_NUM;
}
#endif /* CUSTOMER_HW2 */
if (dhd_oob_gpio_num < 0) {
WL_ERROR(("%s: ERROR customer specific Host GPIO is NOT defined \n",
__FUNCTION__));
return (dhd_oob_gpio_num);
}
WL_ERROR(("%s: customer specific Host GPIO number is (%d)\n",
__FUNCTION__, dhd_oob_gpio_num));
#if defined CUSTOMER_HW
host_oob_irq = MSM_GPIO_TO_INT(dhd_oob_gpio_num);
#elif defined CUSTOMER_HW3
gpio_request(dhd_oob_gpio_num, "oob irq");
host_oob_irq = gpio_to_irq(dhd_oob_gpio_num);
gpio_direction_input(dhd_oob_gpio_num);
#endif /* CUSTOMER_HW */
#endif /* CUSTOMER_HW2 */
return (host_oob_irq);
}
/* This function will return:
* 1) return : Host gpio interrupt number per customer platform
* 2) irq_flags_ptr : Type of Host interrupt as Level or Edge
*
* NOTE :
* Customer should check his platform definitions
* and his Host Interrupt spec
* to figure out the proper setting for his platform.
* Broadcom provides just reference settings as example.
*
*/
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq = 0;
#ifdef CUSTOMER_HW2
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
#else
#if defined(CUSTOM_OOB_GPIO_NUM)
if (dhd_oob_gpio_num < 0) {
dhd_oob_gpio_num = CUSTOM_OOB_GPIO_NUM;
}
#endif /* CUSTOMER_HW2 */
dhd_oob_gpio_num = 1*32 + 24;
if (dhd_oob_gpio_num < 0) {
WL_ERROR(("%s: ERROR customer specific Host GPIO is NOT defined \n",
__FUNCTION__));
return (dhd_oob_gpio_num);
}
WL_ERROR(("%s: customer specific Host GPIO number is (%d)\n",
__FUNCTION__, dhd_oob_gpio_num));
#if defined CUSTOMER_HW
host_oob_irq = MSM_GPIO_TO_INT(dhd_oob_gpio_num);
#elif defined CUSTOMER_HW3
gpio_request(dhd_oob_gpio_num, "oob irq");
host_oob_irq = gpio_to_irq(dhd_oob_gpio_num);
gpio_direction_input(dhd_oob_gpio_num);
#endif /* CUSTOMER_HW */
#endif /* CUSTOMER_HW2 */
gpio_request(dhd_oob_gpio_num, "wl-host-wake");
host_oob_irq = gpio_to_irq(dhd_oob_gpio_num);
gpio_direction_input(dhd_oob_gpio_num);
printk(KERN_ERR"fxz-%s: called [%d]\n", __func__, host_oob_irq);
return (host_oob_irq);
}
/* This function will return:
* 1) return : Host gpio interrupt number per customer platform
* 2) irq_flags_ptr : Type of Host interrupt as Level or Edge
*
* NOTE :
* Customer should check his platform definitions
* and his Host Interrupt spec
* to figure out the proper setting for his platform.
* Broadcom provides just reference settings as example.
*
*/
int dhd_customer_oob_irq_map(unsigned long *irq_flags_ptr)
{
int host_oob_irq = 0;
#if (defined(CUSTOMER_HW2) || defined(CUSTOMER_HW4)) && !defined(PLATFORM_MPS)
printk(KERN_ERR "irq 0011\n");
host_oob_irq = wifi_get_irq_number(irq_flags_ptr);
#else
printk(KERN_ERR "irq 0022\n");
#if defined(CUSTOM_OOB_GPIO_NUM)
if (dhd_oob_gpio_num < 0) {
dhd_oob_gpio_num = CUSTOM_OOB_GPIO_NUM;
}
#endif /* CUSTOMER_OOB_GPIO_NUM */
if (dhd_oob_gpio_num < 0) {
WL_ERROR(("%s: ERROR customer specific Host GPIO is NOT defined \n",
__FUNCTION__));
return (dhd_oob_gpio_num);
}
WL_ERROR(("%s: customer specific Host GPIO number is (%d)\n",
__FUNCTION__, dhd_oob_gpio_num));
#if defined CUSTOMER_HW
printk(KERN_ERR "irq 0044\n", irq);
host_oob_irq = MSM_GPIO_TO_INT(dhd_oob_gpio_num);
#elif defined CUSTOMER_HW3 || defined(PLATFORM_MPS)
printk(KERN_ERR "irq 0055\n", irq);
gpio_request(dhd_oob_gpio_num, "oob irq");
host_oob_irq = gpio_to_irq(dhd_oob_gpio_num);
gpio_direction_input(dhd_oob_gpio_num);
#endif /* CUSTOMER_HW */
#endif /* CUSTOMER_HW2 || CUSTOMER_HW4 */
return (host_oob_irq);
}
