/*! \brief Main function.
*/
int main(void)
{
irq_initialize_vectors();
#if SAMD20
system_init();
delay_init();
#else
sysclk_init();
/* Initialize the board.
* The board-specific conf_board.h file contains the configuration of
* the board initialization.
*/
board_init();
#endif
sw_timer_init();
serial_interface_init();
if (MAC_SUCCESS != wpan_init()) {
app_alert();
}
LED_On(LED_POWER);
cpu_irq_enable();
while (1) {
wpan_task();
serial_data_handler();
}
}
/**
* \brief Performs a Reset check on AT86RFx module
*
* This function will simply test the output of the function
* \ref wpan_mlme_reset_req and returns an error in case of failure.
*
* \param test Current test case.
*/
static void run_wpan_reset_test(const struct test_case *test)
{
wpan_mlme_reset_req(true);
while (!wpan_reset_conf_rcvd) {
wpan_task();
}
test_assert_true(test, wpan_reset_conf_status == MAC_SUCCESS,
"AVR2025_MAC - MAC Reset request failed");
}
static void run_wpan_scan_test(const struct test_case *test)
{
wpan_mlme_scan_req(MLME_SCAN_TYPE_ACTIVE,
SCAN_CHANNEL,
SCAN_DURATION,
DEFAULT_CHANNEL_PAGE);
while (!wpan_scan_conf_rcvd) {
wpan_task();
}
test_assert_true(test,
(wpan_scan_conf_status == MAC_SUCCESS) ||
(wpan_scan_conf_status == MAC_NO_BEACON),
"AVR2025_MAC - MAC Scan test failed");
}
/*! \brief Main function.
*/
int main(void)
{
/* Initialize the board.
* The board-specific conf_board.h file contains the configuration of
* the board initialization.
*/
irq_initialize_vectors();
board_init();
sysclk_init();
sw_timer_init();
if(MAC_SUCCESS != wpan_init())
{
/*
* Stay here; we need a valid IEEE address.
* Check kit documentation how to create an IEEE address
* and to store it into the EEPROM.
*/
app_alert();
}
/* Initialize LEDs. */
LED_On(LED_START); // indicating application is started
LED_Off(LED_NWK_SETUP); // indicating node is associated
LED_Off(LED_DATA); // indicating successfull data transmission
cpu_irq_enable();
sw_timer_get_id(&TIMER_LED_OFF);
sw_timer_get_id(&WAKE_TIMER);
node_status = COLD_START_RESET;
/*
* Reset the MAC layer to the default values
* This request will cause a mlme reset confirm message ->
* usr_mlme_reset_conf
*/
wpan_mlme_reset_req(true);
/* Main loop */
while (true)
{
wpan_task();
app_task(); /* Application task */
}
}
/**
* @brief Main function of the device application
*/
int main(void)
{
/* Initialize the board.
* The board-specific conf_board.h file contains the configuration of
* the board initialization.
*/
irq_initialize_vectors();
board_init();
sysclk_init();
sw_timer_init();
if(MAC_SUCCESS != wpan_init())
{
app_alert();
}
/* Initialize LEDs. */
LED_On(LED_START); // indicating application is started
LED_Off(LED_NWK_SETUP); // indicating node is associated
LED_Off(LED_DATA); // indicating successfull data transmission
cpu_irq_enable();
#ifdef SIO_HUB
/* Initialize the serial interface used for communication with terminal program. */
sio2host_init();
/* To make sure the hyper terminal gets connected to the system */
sio2host_getchar();
printf("\nNobeacon_Application\r\n\n");
printf("\nDevice\r\n\n");
#endif /* SIO_HUB */
sw_timer_get_id(&APP_TIMER_LED_OFF);
sw_timer_get_id(&APP_TIMER_POLL_DATA);
wpan_mlme_reset_req(true);
while (true)
{
wpan_task();
}
}
/**
* \brief Run Wireless Module unit tests
*
* Initializes the clock system, board and USB.
* Then runs the wireless task continuously.
*/
int main(void)
{
irq_initialize_vectors();
sysclk_init();
/* Initialize the board.
* The board-specific conf_board.h file contains the configuration of
* the board initialization.
*/
board_init();
sw_timer_init();
wpan_init();
/* Enable interrupts */
cpu_irq_enable();
stdio_usb_init();
while (1) {
wpan_task();
}
}
/**
* @brief Main function of the coordinator application
*
* This function initializes the MAC, initiates a MLME reset request
* (@ref wpan_mlme_reset_req()), and implements a the main loop.
*/
int main(void)
{
irq_initialize_vectors();
#if SAMD20
system_init();
delay_init();
#else
sysclk_init();
/* Initialize the board.
* The board-specific conf_board.h file contains the configuration of
* the board initialization.
*/
board_init();
#endif
#ifdef SIO_HUB
sio2host_init();
#endif
sw_timer_init();
if (MAC_SUCCESS != wpan_init()) {
app_alert();
}
/* Initialize LEDs. */
LED_On(LED_START); /* indicating application is started */
LED_Off(LED_NWK_SETUP); /* indicating network is started */
LED_Off(LED_DATA); /* indicating data transmission */
cpu_irq_enable();
#ifdef SIO_HUB
/* Initialize the serial interface used for communication with terminal
*program. */
/* To make sure the Hyper Terminal Connected to the system*/
sio2host_getchar();
#ifdef BEACON_SUPPORT
printf("\nBeacon_Application\r\n\n");
#else
printf("\nNO Beacon_Application\r\n\n");
#endif
printf("\nCoordinator\r\n\n");
print_stack_app_build_features();
#endif /* SIO_HUB */
sw_timer_get_id(&APP_TIMER_INDIRECT_DATA);
sw_timer_get_id(&APP_TIMER_BCN_PAYLOAD_UPDATE);
sw_timer_get_id(&APP_TIMER_BC_DATA);
#ifdef GTS_SUPPORT
sw_timer_get_id(&APP_TIMER_GTS_DATA);
#endif
/*
* Reset the MAC layer to the default values.
* This request will cause a mlme reset confirm message ->
* usr_mlme_reset_conf
*/
wpan_mlme_reset_req(true);
#ifdef GPIO_PUSH_BUTTON_0
dst_addr.AddrMode = 2;
dst_addr.PANId = DEFAULT_PAN_ID;
#endif /* GPIO_PUSH_BUTTON_0 */
while (true) {
wpan_task();
#ifdef GPIO_PUSH_BUTTON_0
if (!ioport_get_pin_level(GPIO_PUSH_BUTTON_0)) {
delay_ms(DEBOUNCE_DELAY_MS);
if (!ioport_get_pin_level(GPIO_PUSH_BUTTON_0)) {
dst_addr.Addr.short_address = BROADCAST;
wpan_mcps_data_req(FCF_SHORT_ADDR, &dst_addr,
strlen(broadcast_payload),
(uint8_t *)&broadcast_payload, 1,
WPAN_TXOPT_OFF);
}
}
#endif /* GPIO_PUSH_BUTTON_0 */
}
}
/**
* @brief Main function of the device application
*/
int main(void)
{
irq_initialize_vectors();
#if SAMD || SAMR21
system_init();
delay_init();
#else
sysclk_init();
/* Initialize the board.
* The board-specific conf_board.h file contains the configuration of
* the board initialization.
*/
board_init();
#endif
#ifdef SIO_HUB
sio2host_init();
#endif
sw_timer_init();
if (MAC_SUCCESS != wpan_init()) {
app_alert();
}
/* Initialize LEDs. */
LED_On(LED_START); /* indicating application is started */
LED_Off(LED_NWK_SETUP); /* indicating network is started */
LED_Off(LED_DATA); /* indicating data transmission */
cpu_irq_enable();
#ifdef SIO_HUB
/* Initialize the serial interface used for communication with terminal
* program. */
/* To Make sure the Hyper Terminal to the System */
sio2host_getchar();
printf("\nBeacon_Application\r\n\n");
printf("\nDevice\r\n\n");
print_stack_app_build_features();
#endif
sw_timer_get_id(&APP_TIMER);
wpan_mlme_reset_req(true);
#ifdef ENABLE_SLEEP
sw_timer_get_id(&APP_TIMER_SLEEP);
#endif
LED_Off(LED_NWK_SETUP);
while (true) {
wpan_task();
#if (defined ENABLE_SLEEP || defined RTC_SLEEP)
/* Requesting MAC for Sleep Duration*/
sleep_time = mac_ready_to_sleep();
if ((sleep_time > (uint32_t)APP_GUARD_TIME_US)) {
/*Entering Power save Mode when the sleep duration is
* above the guard time*/
enter_sleep(sleep_time);
}
#endif
}
}
