/*
* Real startup routine, powers up the hardware and sets up
* the SCC. Returns a delay in ms where you need to wait before
* actually using the port, this is typically the internal modem
* powerup delay. This routine expect the lock to be taken.
*/
static int __pmz_startup(struct uart_pmac_port *uap)
{
int pwr_delay = 0;
memset(&uap->curregs, 0, sizeof(uap->curregs));
/* Power up the SCC & underlying hardware (modem/irda) */
pwr_delay = pmz_set_scc_power(uap, 1);
/* Nice buggy HW ... */
pmz_fix_zero_bug_scc(uap);
/* Reset the channel */
uap->curregs[R9] = 0;
write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB);
zssync(uap);
udelay(10);
write_zsreg(uap, 9, 0);
zssync(uap);
/* Clear the interrupt registers */
write_zsreg(uap, R1, 0);
write_zsreg(uap, R0, ERR_RES);
write_zsreg(uap, R0, ERR_RES);
write_zsreg(uap, R0, RES_H_IUS);
write_zsreg(uap, R0, RES_H_IUS);
/* Setup some valid baud rate */
uap->curregs[R4] = X16CLK | SB1;
uap->curregs[R3] = Rx8;
uap->curregs[R5] = Tx8 | RTS;
if (!ZS_IS_IRDA(uap))
uap->curregs[R5] |= DTR;
uap->curregs[R12] = 0;
uap->curregs[R13] = 0;
uap->curregs[R14] = BRENAB;
/* Clear handshaking, enable BREAK interrupts */
uap->curregs[R15] = BRKIE;
/* Master interrupt enable */
uap->curregs[R9] |= NV | MIE;
pmz_load_zsregs(uap, uap->curregs);
/* Enable receiver and transmitter. */
write_zsreg(uap, R3, uap->curregs[R3] |= RxENABLE);
write_zsreg(uap, R5, uap->curregs[R5] |= TxENABLE);
/* Remember status for DCD/CTS changes */
uap->prev_status = read_zsreg(uap, R0);
return pwr_delay;
}
static void pmz_irda_reset(struct uart_pmac_port *uap)
{
uap->curregs[R5] |= DTR;
write_zsreg(uap, R5, uap->curregs[R5]);
zssync(uap);
mdelay(110);
uap->curregs[R5] &= ~DTR;
write_zsreg(uap, R5, uap->curregs[R5]);
zssync(uap);
mdelay(10);
}
static void pmz_status_handle(struct uart_pmac_port *uap)
{
unsigned char status;
status = read_zsreg(uap, R0);
write_zsreg(uap, R0, RES_EXT_INT);
zssync(uap);
if (ZS_IS_OPEN(uap) && ZS_WANTS_MODEM_STATUS(uap)) {
if (status & SYNC_HUNT)
uap->port.icount.dsr++;
/* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
* But it does not tell us which bit has changed, we have to keep
* track of this ourselves.
* The CTS input is inverted for some reason. -- paulus
*/
if ((status ^ uap->prev_status) & DCD)
uart_handle_dcd_change(&uap->port,
(status & DCD));
if ((status ^ uap->prev_status) & CTS)
uart_handle_cts_change(&uap->port,
!(status & CTS));
wake_up_interruptible(&uap->port.info->delta_msr_wait);
}
if (status & BRK_ABRT)
uap->flags |= PMACZILOG_FLAG_BREAK;
uap->prev_status = status;
}
/*
* Kick the Tx side.
* The port lock is held and interrupts are disabled.
*/
static void pmz_start_tx(struct uart_port *port)
{
struct uart_pmac_port *uap = to_pmz(port);
unsigned char status;
pmz_debug("pmz: start_tx()\n");
uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED;
if (ZS_IS_ASLEEP(uap) || uap->node == NULL)
return;
status = read_zsreg(uap, R0);
/* TX busy? Just wait for the TX done interrupt. */
if (!(status & Tx_BUF_EMP))
return;
/* Send the first character to jump-start the TX done
* IRQ sending engine.
*/
if (port->x_char) {
write_zsdata(uap, port->x_char);
zssync(uap);
port->icount.tx++;
port->x_char = 0;
} else {
struct circ_buf *xmit = &port->info->xmit;
write_zsdata(uap, xmit->buf[xmit->tail]);
zssync(uap);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
port->icount.tx++;
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&uap->port);
}
pmz_debug("pmz: start_tx() done.\n");
}
static void pmz_shutdown(struct uart_port *port)
{
struct uart_pmac_port *uap = to_pmz(port);
unsigned long flags;
pmz_debug("pmz: shutdown()\n");
if (uap->node == NULL)
return;
mutex_lock(&pmz_irq_mutex);
/* Release interrupt handler */
free_irq(uap->port.irq, uap);
spin_lock_irqsave(&port->lock, flags);
uap->flags &= ~PMACZILOG_FLAG_IS_OPEN;
if (!ZS_IS_OPEN(uap->mate))
pmz_get_port_A(uap)->flags &= ~PMACZILOG_FLAG_IS_IRQ_ON;
/* Disable interrupts */
if (!ZS_IS_ASLEEP(uap)) {
uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
write_zsreg(uap, R1, uap->curregs[R1]);
zssync(uap);
}
if (ZS_IS_CONS(uap) || ZS_IS_ASLEEP(uap)) {
spin_unlock_irqrestore(&port->lock, flags);
mutex_unlock(&pmz_irq_mutex);
return;
}
/* Disable receiver and transmitter. */
uap->curregs[R3] &= ~RxENABLE;
uap->curregs[R5] &= ~TxENABLE;
/* Disable all interrupts and BRK assertion. */
uap->curregs[R5] &= ~SND_BRK;
pmz_maybe_update_regs(uap);
/* Shut the chip down */
pmz_set_scc_power(uap, 0);
spin_unlock_irqrestore(&port->lock, flags);
mutex_unlock(&pmz_irq_mutex);
pmz_debug("pmz: shutdown() done.\n");
}
/*
* FixZeroBug....Works around a bug in the SCC receving channel.
* Inspired from Darwin code, 15 Sept. 2000 -DanM
*
* The following sequence prevents a problem that is seen with O'Hare ASICs
* (most versions -- also with some Heathrow and Hydra ASICs) where a zero
* at the input to the receiver becomes 'stuck' and locks up the receiver.
* This problem can occur as a result of a zero bit at the receiver input
* coincident with any of the following events:
*
* The SCC is initialized (hardware or software).
* A framing error is detected.
* The clocking option changes from synchronous or X1 asynchronous
* clocking to X16, X32, or X64 asynchronous clocking.
* The decoding mode is changed among NRZ, NRZI, FM0, or FM1.
*
* This workaround attempts to recover from the lockup condition by placing
* the SCC in synchronous loopback mode with a fast clock before programming
* any of the asynchronous modes.
*/
static void pmz_fix_zero_bug_scc(struct uart_pmac_port *uap)
{
write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB);
zssync(uap);
udelay(10);
write_zsreg(uap, 9, (ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB) | NV);
zssync(uap);
write_zsreg(uap, 4, X1CLK | MONSYNC);
write_zsreg(uap, 3, Rx8);
write_zsreg(uap, 5, Tx8 | RTS);
write_zsreg(uap, 9, NV); /* Didn't we already do this? */
write_zsreg(uap, 11, RCBR | TCBR);
write_zsreg(uap, 12, 0);
write_zsreg(uap, 13, 0);
write_zsreg(uap, 14, (LOOPBAK | BRSRC));
write_zsreg(uap, 14, (LOOPBAK | BRSRC | BRENAB));
write_zsreg(uap, 3, Rx8 | RxENABLE);
write_zsreg(uap, 0, RES_EXT_INT);
write_zsreg(uap, 0, RES_EXT_INT);
write_zsreg(uap, 0, RES_EXT_INT); /* to kill some time */
/* The channel should be OK now, but it is probably receiving
* loopback garbage.
* Switch to asynchronous mode, disable the receiver,
* and discard everything in the receive buffer.
*/
write_zsreg(uap, 9, NV);
write_zsreg(uap, 4, X16CLK | SB_MASK);
write_zsreg(uap, 3, Rx8);
while (read_zsreg(uap, 0) & Rx_CH_AV) {
(void)read_zsreg(uap, 8);
write_zsreg(uap, 0, RES_EXT_INT);
write_zsreg(uap, 0, ERR_RES);
}
}
static void __pmz_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_pmac_port *uap = to_pmz(port);
unsigned long baud;
pmz_debug("pmz: set_termios()\n");
if (ZS_IS_ASLEEP(uap))
return;
memcpy(&uap->termios_cache, termios, sizeof(struct ktermios));
/* XXX Check which revs of machines actually allow 1 and 4Mb speeds
* on the IR dongle. Note that the IRTTY driver currently doesn't know
* about the FIR mode and high speed modes. So these are unused. For
* implementing proper support for these, we should probably add some
* DMA as well, at least on the Rx side, which isn't a simple thing
* at this point.
*/
if (ZS_IS_IRDA(uap)) {
/* Calc baud rate */
baud = uart_get_baud_rate(port, termios, old, 1200, 4000000);
pmz_debug("pmz: switch IRDA to %ld bauds\n", baud);
/* Cet the irda codec to the right rate */
pmz_irda_setup(uap, &baud);
/* Set final baud rate */
pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud);
pmz_load_zsregs(uap, uap->curregs);
zssync(uap);
} else {
baud = uart_get_baud_rate(port, termios, old, 1200, 230400);
pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud);
/* Make sure modem status interrupts are correctly configured */
if (UART_ENABLE_MS(&uap->port, termios->c_cflag)) {
uap->curregs[R15] |= DCDIE | SYNCIE | CTSIE;
uap->flags |= PMACZILOG_FLAG_MODEM_STATUS;
} else {
uap->curregs[R15] &= ~(DCDIE | SYNCIE | CTSIE);
uap->flags &= ~PMACZILOG_FLAG_MODEM_STATUS;
}
/* Load registers to the chip */
pmz_maybe_update_regs(uap);
}
uart_update_timeout(port, termios->c_cflag, baud);
pmz_debug("pmz: set_termios() done.\n");
}
/*
* Set Modem Control (RTS & DTR) bits
* The port lock is held and interrupts are disabled.
* Note: Shall we really filter out RTS on external ports or
* should that be dealt at higher level only ?
*/
static void pmz_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_pmac_port *uap = to_pmz(port);
unsigned char set_bits, clear_bits;
/* Do nothing for irda for now... */
if (ZS_IS_IRDA(uap))
return;
/* We get called during boot with a port not up yet */
if (ZS_IS_ASLEEP(uap) ||
!(ZS_IS_OPEN(uap) || ZS_IS_CONS(uap)))
return;
set_bits = clear_bits = 0;
if (ZS_IS_INTMODEM(uap)) {
if (mctrl & TIOCM_RTS)
set_bits |= RTS;
else
clear_bits |= RTS;
}
if (mctrl & TIOCM_DTR)
set_bits |= DTR;
else
clear_bits |= DTR;
/* NOTE: Not subject to 'transmitter active' rule. */
uap->curregs[R5] |= set_bits;
uap->curregs[R5] &= ~clear_bits;
if (ZS_IS_ASLEEP(uap))
return;
write_zsreg(uap, R5, uap->curregs[R5]);
pmz_debug("pmz_set_mctrl: set bits: %x, clear bits: %x -> %x\n",
set_bits, clear_bits, uap->curregs[R5]);
zssync(uap);
}
/* Hrm... we register that twice, fixme later.... */
static irqreturn_t pmz_interrupt(int irq, void *dev_id)
{
struct uart_pmac_port *uap = dev_id;
struct uart_pmac_port *uap_a;
struct uart_pmac_port *uap_b;
int rc = IRQ_NONE;
struct tty_struct *tty;
u8 r3;
uap_a = pmz_get_port_A(uap);
uap_b = uap_a->mate;
spin_lock(&uap_a->port.lock);
r3 = read_zsreg(uap_a, R3);
#ifdef DEBUG_HARD
pmz_debug("irq, r3: %x\n", r3);
#endif
/* Channel A */
tty = NULL;
if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
write_zsreg(uap_a, R0, RES_H_IUS);
zssync(uap_a);
if (r3 & CHAEXT)
pmz_status_handle(uap_a);
if (r3 & CHARxIP)
tty = pmz_receive_chars(uap_a);
if (r3 & CHATxIP)
pmz_transmit_chars(uap_a);
rc = IRQ_HANDLED;
}
spin_unlock(&uap_a->port.lock);
if (tty != NULL)
tty_flip_buffer_push(tty);
if (uap_b->node == NULL)
goto out;
spin_lock(&uap_b->port.lock);
tty = NULL;
if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
write_zsreg(uap_b, R0, RES_H_IUS);
zssync(uap_b);
if (r3 & CHBEXT)
pmz_status_handle(uap_b);
if (r3 & CHBRxIP)
tty = pmz_receive_chars(uap_b);
if (r3 & CHBTxIP)
pmz_transmit_chars(uap_b);
rc = IRQ_HANDLED;
}
spin_unlock(&uap_b->port.lock);
if (tty != NULL)
tty_flip_buffer_push(tty);
out:
#ifdef DEBUG_HARD
pmz_debug("irq done.\n");
#endif
return rc;
}
static void pmz_transmit_chars(struct uart_pmac_port *uap)
{
struct circ_buf *xmit;
if (ZS_IS_ASLEEP(uap))
return;
if (ZS_IS_CONS(uap)) {
unsigned char status = read_zsreg(uap, R0);
/* TX still busy? Just wait for the next TX done interrupt.
*
* It can occur because of how we do serial console writes. It would
* be nice to transmit console writes just like we normally would for
* a TTY line. (ie. buffered and TX interrupt driven). That is not
* easy because console writes cannot sleep. One solution might be
* to poll on enough port->xmit space becomming free. -DaveM
*/
if (!(status & Tx_BUF_EMP))
return;
}
uap->flags &= ~PMACZILOG_FLAG_TX_ACTIVE;
if (ZS_REGS_HELD(uap)) {
pmz_load_zsregs(uap, uap->curregs);
uap->flags &= ~PMACZILOG_FLAG_REGS_HELD;
}
if (ZS_TX_STOPPED(uap)) {
uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED;
goto ack_tx_int;
}
if (uap->port.x_char) {
uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
write_zsdata(uap, uap->port.x_char);
zssync(uap);
uap->port.icount.tx++;
uap->port.x_char = 0;
return;
}
if (uap->port.info == NULL)
goto ack_tx_int;
xmit = &uap->port.info->xmit;
if (uart_circ_empty(xmit)) {
uart_write_wakeup(&uap->port);
goto ack_tx_int;
}
if (uart_tx_stopped(&uap->port))
goto ack_tx_int;
uap->flags |= PMACZILOG_FLAG_TX_ACTIVE;
write_zsdata(uap, xmit->buf[xmit->tail]);
zssync(uap);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
uap->port.icount.tx++;
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&uap->port);
return;
ack_tx_int:
write_zsreg(uap, R0, RES_Tx_P);
zssync(uap);
}
static struct tty_struct *pmz_receive_chars(struct uart_pmac_port *uap)
{
struct tty_struct *tty = NULL;
unsigned char ch, r1, drop, error, flag;
int loops = 0;
/* The interrupt can be enabled when the port isn't open, typically
* that happens when using one port is open and the other closed (stale
* interrupt) or when one port is used as a console.
*/
if (!ZS_IS_OPEN(uap)) {
pmz_debug("pmz: draining input\n");
/* Port is closed, drain input data */
for (;;) {
if ((++loops) > 1000)
goto flood;
(void)read_zsreg(uap, R1);
write_zsreg(uap, R0, ERR_RES);
(void)read_zsdata(uap);
ch = read_zsreg(uap, R0);
if (!(ch & Rx_CH_AV))
break;
}
return NULL;
}
/* Sanity check, make sure the old bug is no longer happening */
if (uap->port.info == NULL || uap->port.info->tty == NULL) {
WARN_ON(1);
(void)read_zsdata(uap);
return NULL;
}
tty = uap->port.info->tty;
while (1) {
error = 0;
drop = 0;
r1 = read_zsreg(uap, R1);
ch = read_zsdata(uap);
if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
write_zsreg(uap, R0, ERR_RES);
zssync(uap);
}
ch &= uap->parity_mask;
if (ch == 0 && uap->flags & PMACZILOG_FLAG_BREAK) {
uap->flags &= ~PMACZILOG_FLAG_BREAK;
}
#if defined(CONFIG_MAGIC_SYSRQ) && defined(CONFIG_SERIAL_CORE_CONSOLE)
#ifdef USE_CTRL_O_SYSRQ
/* Handle the SysRq ^O Hack */
if (ch == '\x0f') {
uap->port.sysrq = jiffies + HZ*5;
goto next_char;
}
#endif /* USE_CTRL_O_SYSRQ */
if (uap->port.sysrq) {
int swallow;
spin_unlock(&uap->port.lock);
swallow = uart_handle_sysrq_char(&uap->port, ch);
spin_lock(&uap->port.lock);
if (swallow)
goto next_char;
}
#endif /* CONFIG_MAGIC_SYSRQ && CONFIG_SERIAL_CORE_CONSOLE */
/* A real serial line, record the character and status. */
if (drop)
goto next_char;
flag = TTY_NORMAL;
uap->port.icount.rx++;
if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR | BRK_ABRT)) {
error = 1;
if (r1 & BRK_ABRT) {
pmz_debug("pmz: got break !\n");
r1 &= ~(PAR_ERR | CRC_ERR);
uap->port.icount.brk++;
if (uart_handle_break(&uap->port))
goto next_char;
}
else if (r1 & PAR_ERR)
uap->port.icount.parity++;
else if (r1 & CRC_ERR)
uap->port.icount.frame++;
if (r1 & Rx_OVR)
uap->port.icount.overrun++;
r1 &= uap->port.read_status_mask;
if (r1 & BRK_ABRT)
flag = TTY_BREAK;
else if (r1 & PAR_ERR)
flag = TTY_PARITY;
else if (r1 & CRC_ERR)
flag = TTY_FRAME;
}
if (uap->port.ignore_status_mask == 0xff ||
(r1 & uap->port.ignore_status_mask) == 0) {
tty_insert_flip_char(tty, ch, flag);
}
if (r1 & Rx_OVR)
tty_insert_flip_char(tty, 0, TTY_OVERRUN);
next_char:
/* We can get stuck in an infinite loop getting char 0 when the
* line is in a wrong HW state, we break that here.
* When that happens, I disable the receive side of the driver.
* Note that what I've been experiencing is a real irq loop where
* I'm getting flooded regardless of the actual port speed.
* Something stange is going on with the HW
*/
if ((++loops) > 1000)
goto flood;
ch = read_zsreg(uap, R0);
if (!(ch & Rx_CH_AV))
break;
}
return tty;
flood:
uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
write_zsreg(uap, R1, uap->curregs[R1]);
zssync(uap);
dev_err(&uap->dev->ofdev.dev, "pmz: rx irq flood !\n");
return tty;
}
/*
* Set the irda codec on the imac to the specified baud rate.
*/
static void pmz_irda_setup(struct uart_pmac_port *uap, unsigned long *baud)
{
u8 cmdbyte;
int t, version;
switch (*baud) {
/* SIR modes */
case 2400:
cmdbyte = 0x53;
break;
case 4800:
cmdbyte = 0x52;
break;
case 9600:
cmdbyte = 0x51;
break;
case 19200:
cmdbyte = 0x50;
break;
case 38400:
cmdbyte = 0x4f;
break;
case 57600:
cmdbyte = 0x4e;
break;
case 115200:
cmdbyte = 0x4d;
break;
/* The FIR modes aren't really supported at this point, how
* do we select the speed ? via the FCR on KeyLargo ?
*/
case 1152000:
cmdbyte = 0;
break;
case 4000000:
cmdbyte = 0;
break;
default: /* 9600 */
cmdbyte = 0x51;
*baud = 9600;
break;
}
/* Wait for transmitter to drain */
t = 10000;
while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0
|| (read_zsreg(uap, R1) & ALL_SNT) == 0) {
if (--t <= 0) {
dev_err(&uap->dev->ofdev.dev, "transmitter didn't drain\n");
return;
}
udelay(10);
}
/* Drain the receiver too */
t = 100;
(void)read_zsdata(uap);
(void)read_zsdata(uap);
(void)read_zsdata(uap);
mdelay(10);
while (read_zsreg(uap, R0) & Rx_CH_AV) {
read_zsdata(uap);
mdelay(10);
if (--t <= 0) {
dev_err(&uap->dev->ofdev.dev, "receiver didn't drain\n");
return;
}
}
/* Switch to command mode */
uap->curregs[R5] |= DTR;
write_zsreg(uap, R5, uap->curregs[R5]);
zssync(uap);
mdelay(1);
/* Switch SCC to 19200 */
pmz_convert_to_zs(uap, CS8, 0, 19200);
pmz_load_zsregs(uap, uap->curregs);
mdelay(1);
/* Write get_version command byte */
write_zsdata(uap, 1);
t = 5000;
while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) {
if (--t <= 0) {
dev_err(&uap->dev->ofdev.dev,
"irda_setup timed out on get_version byte\n");
goto out;
}
udelay(10);
}
version = read_zsdata(uap);
if (version < 4) {
dev_info(&uap->dev->ofdev.dev, "IrDA: dongle version %d not supported\n",
version);
goto out;
}
/* Send speed mode */
write_zsdata(uap, cmdbyte);
t = 5000;
while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) {
if (--t <= 0) {
dev_err(&uap->dev->ofdev.dev,
"irda_setup timed out on speed mode byte\n");
goto out;
}
udelay(10);
}
t = read_zsdata(uap);
if (t != cmdbyte)
dev_err(&uap->dev->ofdev.dev,
"irda_setup speed mode byte = %x (%x)\n", t, cmdbyte);
dev_info(&uap->dev->ofdev.dev, "IrDA setup for %ld bps, dongle version: %d\n",
*baud, version);
(void)read_zsdata(uap);
(void)read_zsdata(uap);
(void)read_zsdata(uap);
out:
/* Switch back to data mode */
uap->curregs[R5] &= ~DTR;
write_zsreg(uap, R5, uap->curregs[R5]);
zssync(uap);
(void)read_zsdata(uap);
(void)read_zsdata(uap);
(void)read_zsdata(uap);
}
/*
* Load all registers to reprogram the port
* This function must only be called when the TX is not busy. The UART
* port lock must be held and local interrupts disabled.
*/
static void pmz_load_zsregs(struct uart_pmac_port *uap, u8 *regs)
{
int i;
if (ZS_IS_ASLEEP(uap))
return;
/* Let pending transmits finish. */
for (i = 0; i < 1000; i++) {
unsigned char stat = read_zsreg(uap, R1);
if (stat & ALL_SNT)
break;
udelay(100);
}
ZS_CLEARERR(uap);
zssync(uap);
ZS_CLEARFIFO(uap);
zssync(uap);
ZS_CLEARERR(uap);
/* Disable all interrupts. */
write_zsreg(uap, R1,
regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
/* Set parity, sync config, stop bits, and clock divisor. */
write_zsreg(uap, R4, regs[R4]);
/* Set misc. TX/RX control bits. */
write_zsreg(uap, R10, regs[R10]);
/* Set TX/RX controls sans the enable bits. */
write_zsreg(uap, R3, regs[R3] & ~RxENABLE);
write_zsreg(uap, R5, regs[R5] & ~TxENABLE);
/* now set R7 "prime" on ESCC */
write_zsreg(uap, R15, regs[R15] | EN85C30);
write_zsreg(uap, R7, regs[R7P]);
/* make sure we use R7 "non-prime" on ESCC */
write_zsreg(uap, R15, regs[R15] & ~EN85C30);
/* Synchronous mode config. */
write_zsreg(uap, R6, regs[R6]);
write_zsreg(uap, R7, regs[R7]);
/* Disable baud generator. */
write_zsreg(uap, R14, regs[R14] & ~BRENAB);
/* Clock mode control. */
write_zsreg(uap, R11, regs[R11]);
/* Lower and upper byte of baud rate generator divisor. */
write_zsreg(uap, R12, regs[R12]);
write_zsreg(uap, R13, regs[R13]);
/* Now rewrite R14, with BRENAB (if set). */
write_zsreg(uap, R14, regs[R14]);
/* Reset external status interrupts. */
write_zsreg(uap, R0, RES_EXT_INT);
write_zsreg(uap, R0, RES_EXT_INT);
/* Rewrite R3/R5, this time without enables masked. */
write_zsreg(uap, R3, regs[R3]);
write_zsreg(uap, R5, regs[R5]);
/* Rewrite R1, this time without IRQ enabled masked. */
write_zsreg(uap, R1, regs[R1]);
/* Enable interrupts */
write_zsreg(uap, R9, regs[R9]);
}
static struct tty_struct *pmz_receive_chars(struct uart_pmac_port *uap,
struct pt_regs *regs)
{
struct tty_struct *tty = NULL;
unsigned char ch, r1, drop, error;
int loops = 0;
retry:
/* The interrupt can be enabled when the port isn't open, typically
* that happens when using one port is open and the other closed (stale
* interrupt) or when one port is used as a console.
*/
if (!ZS_IS_OPEN(uap)) {
pmz_debug("pmz: draining input\n");
/* Port is closed, drain input data */
for (;;) {
if ((++loops) > 1000)
goto flood;
(void)read_zsreg(uap, R1);
write_zsreg(uap, R0, ERR_RES);
(void)read_zsdata(uap);
ch = read_zsreg(uap, R0);
if (!(ch & Rx_CH_AV))
break;
}
return NULL;
}
/* Sanity check, make sure the old bug is no longer happening */
if (uap->port.info == NULL || uap->port.info->tty == NULL) {
WARN_ON(1);
(void)read_zsdata(uap);
return NULL;
}
tty = uap->port.info->tty;
while (1) {
error = 0;
drop = 0;
if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) {
/* Have to drop the lock here */
pmz_debug("pmz: flip overflow\n");
spin_unlock(&uap->port.lock);
tty->flip.work.func((void *)tty);
spin_lock(&uap->port.lock);
if (tty->flip.count >= TTY_FLIPBUF_SIZE)
drop = 1;
if (ZS_IS_ASLEEP(uap))
return NULL;
if (!ZS_IS_OPEN(uap))
goto retry;
}
r1 = read_zsreg(uap, R1);
ch = read_zsdata(uap);
if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
write_zsreg(uap, R0, ERR_RES);
zssync(uap);
}
ch &= uap->parity_mask;
if (ch == 0 && uap->prev_status & BRK_ABRT)
r1 |= BRK_ABRT;
/* A real serial line, record the character and status. */
if (drop)
goto next_char;
*tty->flip.char_buf_ptr = ch;
*tty->flip.flag_buf_ptr = TTY_NORMAL;
uap->port.icount.rx++;
if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR | BRK_ABRT)) {
error = 1;
if (r1 & BRK_ABRT) {
pmz_debug("pmz: got break !\n");
r1 &= ~(PAR_ERR | CRC_ERR);
uap->port.icount.brk++;
if (uart_handle_break(&uap->port)) {
pmz_debug("pmz: do handle break !\n");
goto next_char;
}
}
else if (r1 & PAR_ERR)
uap->port.icount.parity++;
else if (r1 & CRC_ERR)
uap->port.icount.frame++;
if (r1 & Rx_OVR)
uap->port.icount.overrun++;
r1 &= uap->port.read_status_mask;
if (r1 & BRK_ABRT)
*tty->flip.flag_buf_ptr = TTY_BREAK;
else if (r1 & PAR_ERR)
*tty->flip.flag_buf_ptr = TTY_PARITY;
else if (r1 & CRC_ERR)
*tty->flip.flag_buf_ptr = TTY_FRAME;
}
if (uart_handle_sysrq_char(&uap->port, ch, regs)) {
pmz_debug("pmz: sysrq swallowed the char\n");
goto next_char;
}
if (uap->port.ignore_status_mask == 0xff ||
(r1 & uap->port.ignore_status_mask) == 0) {
tty->flip.flag_buf_ptr++;
tty->flip.char_buf_ptr++;
tty->flip.count++;
}
if ((r1 & Rx_OVR) &&
tty->flip.count < TTY_FLIPBUF_SIZE) {
*tty->flip.flag_buf_ptr = TTY_OVERRUN;
tty->flip.flag_buf_ptr++;
tty->flip.char_buf_ptr++;
tty->flip.count++;
}
next_char:
/* We can get stuck in an infinite loop getting char 0 when the
* line is in a wrong HW state, we break that here.
* When that happens, I disable the receive side of the driver.
* Note that what I've been experiencing is a real irq loop where
* I'm getting flooded regardless of the actual port speed.
* Something stange is going on with the HW
*/
if ((++loops) > 1000)
goto flood;
ch = read_zsreg(uap, R0);
if (!(ch & Rx_CH_AV))
break;
}
return tty;
flood:
uap->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
write_zsreg(uap, R1, uap->curregs[R1]);
zssync(uap);
dev_err(&uap->dev->ofdev.dev, "pmz: rx irq flood !\n");
return tty;
}
