void OperatorControl(void)
{
autonomous = false;
//myRobot.SetSafetyEnabled(false);
//myRobot.SetInvertedMotor(kFrontLeftMotor, true);
// myRobot.SetInvertedMotor(3, true);
//variables for great pid
double rightSpeed,leftSpeed;
float rightSP, leftSP, liftSP, lastLiftSP, gripSP, tempLeftSP, tempRightSP;
float stickY[2];
float stickYAbs[2];
bool lightOn = false;
AxisCamera &camera = AxisCamera::GetInstance();
camera.WriteResolution(AxisCameraParams::kResolution_160x120);
camera.WriteMaxFPS(5);
camera.WriteBrightness(50);
camera.WriteRotation(AxisCameraParams::kRotation_0);
rightEncoder->Start();
leftEncoder->Start();
liftEncoder->Start();
rightEncoder->Reset();
leftEncoder->Reset();
liftEncoder->Reset();
bool fastest = false; //transmission mode
float reduction = 1; //gear reduction from
bool bDrivePID = false;
//float maxSpeed = 500;
float liftPower = 0;
float liftPos = -10;
bool disengageBrake = false;
int count = 0;
//int popCount = 0;
double popStart = 0;
double popTime = 0;
int popStage = 0;
int liftCount = 0;
int liftCount2 = 0;
const float LOG17 = log(17.61093344);
float liftPowerAbs = 0;
float gripError = 0;
float gripErrorAbs = 0;
float gripPropMod = 0;
float gripIntMod = 0;
bool shiftHigh = false;
leftEncoder->SetDistancePerPulse((6 * PI / 1000)/reduction); //6-inch wheels, 1000 raw counts per revolution,
rightEncoder->SetDistancePerPulse((6 * PI / 1000)/reduction); //about 1:1 gear ratio
DriverStationEnhancedIO &myEIO = driverStation->GetEnhancedIO();
GetWatchdog().SetEnabled(true);
GetWatchdog().SetExpiration(0.3);
PIDDriveLeft->SetOutputRange(-1, 1);
PIDDriveRight->SetOutputRange(-1, 1);
//PIDDriveLeft->SetInputRange(-244,244);
//PIDDriveRight->SetInputRange(-244,244);
PIDDriveLeft->SetTolerance(5);
PIDDriveRight->SetTolerance(5);
PIDDriveLeft->SetContinuous(false);
PIDDriveRight->SetContinuous(false);
//PIDDriveLeft->Enable();
//PIDDriveRight->Enable();
PIDDriveRight->SetPID(DRIVEPROPGAIN, DRIVEINTGAIN, DRIVEDERIVGAIN);
PIDDriveLeft->SetPID(DRIVEPROPGAIN, DRIVEINTGAIN, DRIVEDERIVGAIN);
liftSP = 0;
PIDLift->SetTolerance(10);
PIDLift->SetContinuous(false);
PIDLift->SetOutputRange(-0.75, 1.); //BUGBUG
PIDLift->Enable();
gripSP = 0;
float goalGripSP = 0;
bool useGoalSP = true;
bool gripPIDOn = true;
float gripP[10];
float gripI[10];
float gripD[10];
PIDGrip->SetOutputRange(-0.5, 0.28); //Negative goes up
PIDGrip->SetTolerance(5);
PIDGrip->SetSetpoint(0);
PIDGrip->Enable();
miniDep->Set(miniDep->kForward);
int i = 0;
while(i < 10)
{
gripP[i] = GRIPPROPGAIN;
i++;
}
i = 0;
while(i < 10)
{
gripI[i] = GRIPINTGAIN;
i++;
}
i = 0;
while(i < 10)
{
gripD[i] = GRIPDERIVGAIN;
i++;
}
while (IsOperatorControl())
{
GetWatchdog().Feed();
count++;
#if !(SKELETON)
sendVisionData();
#endif
/*
if(LIFTLOW1BUTTON && !(counts%10)) printf("LIFTLOW1BUTTON\n");
if(LIFTLOW2BUTTON && !(counts%10)) printf("LIFTLOW2BUTTON\n");
if(LIFTMID1BUTTON && !(counts%10)) printf("LIFTMID1BUTTON\n");
if(LIFTMID2BUTTON && !(counts%10)) printf("LIFTMID2BUTTON\n");
if(LIFTHIGH1BUTTON && !(counts%10)) printf("LIFTHIGH1BUTTON\n");
if(LIFTHIGH2BUTTON && !(counts%10)) printf("LIFTHIGH2BUTTON\n");
*/
/*
if(lsLeft->Get()) printf("LSLEFT\n");
if(lsMiddle->Get()) printf("LSMIDDLE\n");
if(lsRight->Get()) printf("LSRIGHT\n");
*/
stickY[0] = stickL.GetY();
stickY[1] = stickR.GetY();
stickYAbs[0] = fabs(stickY[0]);
stickYAbs[1] = fabs(stickY[1]);
if(bDrivePID)
{
#if 0
frontLeftMotor->Set(stickY[0]);
rearLeftMotor->Set(stickY[0]);
frontRightMotor->Set(stickY[1]);
rearRightMotor->Set(stickY[1]);
if(!(count%5)) printf("Speeds: %4.2f %4.2f Outputs: %f %f \n", leftEncoder->GetRate(),
rightEncoder->GetRate(), frontLeftMotor->Get(), frontRightMotor->Get());
#endif
if(stickYAbs[0] <= 0.05 )
{
leftSP = 0;
if(!(count%3) && !BACKWARDBUTTON)
{
PIDDriveLeft->Reset();
PIDDriveLeft->Enable();
}
}
else leftSP = stickY[0] * stickY[0] * (stickY[0]/stickYAbs[0]); //set points for pid control
if(stickYAbs[1] <= 0.05)
{
rightSP = 0;
if(!(count%3) && !BACKWARDBUTTON)
{
PIDDriveRight->Reset();
PIDDriveRight->Enable();
}
}
else rightSP = stickY[1] * stickY[1] * (stickY[1]/stickYAbs[1]);
if (BACKWARDBUTTON)
{
tempRightSP = rightSP;
tempLeftSP = leftSP;
rightSP = -tempLeftSP;
leftSP = -tempRightSP; //This line and above line sets opposite values for the controller. ...Theoretically.
}
PIDDriveLeft->SetSetpoint(leftSP);
PIDDriveRight->SetSetpoint(rightSP);
leftSpeed = leftEncoder->GetRate();
rightSpeed = rightEncoder->GetRate();
if(!(count++ % 5))
{
printf("rate L: %2.2f R: %2.2f SP %2.4f %2.4f ERR %2.2f %2.2f Pow: %1.2f %1.2f\n",
leftPIDSource->PIDGet(), rightPIDSource->PIDGet(), leftSP, rightSP,
PIDDriveLeft->GetError(), PIDDriveRight->GetError(), frontLeftMotor->Get(),
frontRightMotor->Get());
//printf("Throttle value: %f", stickR.GetThrottle());
if(PIDDriveRight->OnTarget()) printf("Right on \n");
if(PIDDriveLeft->OnTarget()) printf("Left on \n");
}
if(PIDRESETBUTTON)
{
//PIDDriveRight->SetPID(stickR.GetThrottle()+1,DRIVEINTGAIN, DRIVEDERIVGAIN);
//PIDDriveLeft->SetPID(stickR.GetThrottle()+1,DRIVEINTGAIN, DRIVEDERIVGAIN);
PIDDriveLeft->Reset();
PIDDriveRight->Reset();
PIDDriveLeft->Enable();
PIDDriveRight->Enable();
}
}
else
{
if(PIDDriveLeft->IsEnabled()) PIDDriveLeft->Reset();
if(PIDDriveRight->IsEnabled()) PIDDriveRight->Reset();
if(DEMOSWITCH)
{
stickY[0] = stickY[0]*(1 - lift->getPosition()); //reduces power based on lift height
stickY[1] = stickY[0]*(1 - lift->getPosition());
}
if(stickYAbs[0] > 0.05)
{
frontLeftMotor->Set(stickY[0]);
rearLeftMotor->Set(stickY[0]);
}
else
{
frontLeftMotor->Set(0);
rearLeftMotor->Set(0);
}
if(stickYAbs[1] > 0.05)
{
frontRightMotor->Set(-stickY[1]);
rearRightMotor->Set(-stickY[1]);
}
else
{
frontRightMotor->Set(0);
rearRightMotor->Set(0);
}
}
if(stickL.GetRawButton(2) && stickL.GetRawButton(3) && stickR.GetRawButton(2) &&
stickR.GetRawButton(3) && BACKWARDBUTTON && !(count%5)) bDrivePID = !bDrivePID;
if((SHIFTBUTTON && shiftHigh) || DEMOSWITCH)
{
shifter->Set(shifter->kReverse);
shiftHigh = false;
maxSpeed = 12;
}
else if(!SHIFTBUTTON && !shiftHigh && !DEMOSWITCH)
{
shifter->Set(shifter->kForward);
shiftHigh = true;
maxSpeed = 25; //last value 35
}
sendIOPortData();
#if !(SKELETON)
/*
if(LIGHTBUTTON) lightOn = true;
else lightOn = false;
if(!lightOn) light->Set(light->kOff);
if(lightOn) light->Set(light->kOn);
*/
if(!MODESWITCH)
{
lastLiftSP = liftSP;
if(!PIDLift->IsEnabled()) PIDLift->Enable();
if(LIFTLOW1BUTTON) liftSP = LIFTLOW1;
if(LIFTLOW2BUTTON) liftSP = LIFTLOW2;
if(LIFTMID1BUTTON) liftSP = LIFTMID1;
if(LIFTMID2BUTTON) liftSP = LIFTMID2;
if(LIFTHIGH1BUTTON) liftSP = LIFTHIGH1;
if(LIFTHIGH2BUTTON && !(DEMOSWITCH && (stickYAbs[0] > 0.05 || stickYAbs[1] > 0.05))) liftSP = LIFTHIGH2;
if(!lift->isBraking() && !disengageBrake)
{
PIDLift->SetSetpoint(liftSP);
if(liftSP == 0 && liftPIDSource->PIDGet() < 0.1) //BUGBUG
{
//PIDLift->SetPID(LIFTPROPGAIN, LIFTINTGAIN, 3*LIFTDERIVGAIN);
PIDLift->SetOutputRange(-liftPIDSource->PIDGet() - 0.1, 1.); //BUGBUG
}
else PIDLift->SetOutputRange(-0.75, 1.); //BUGBUG
}
if(lift->isBraking() && lastLiftSP != liftSP)
{
PIDLift->SetSetpoint(lastLiftSP + 0.06);
PIDLift->SetPID(12.5 + 1.5*lift->getPosition(), LIFTINTGAIN + 0.6 + 3*lift->getPosition()/10, 0);
lift->brakeOff();
disengageBrake = true;
if(!liftCount) liftCount = count;
}
//set brake (because near)
if(fabs(PIDLift->GetError()) < 0.01 && !lift->isBraking() && !disengageBrake)
{
if(liftCount == 0) liftCount = count;
if(count - liftCount > 3)
{
PIDLift->Reset();
liftMotor1->Set(LIFTNEUTRALPOWER);
liftMotor2->Set(LIFTNEUTRALPOWER);
Wait(0.02);
lift->brakeOn();
Wait(0.02);
liftMotor1->Set(0.0);
liftMotor2->Set(0.0);
PIDLift->Enable();
PIDLift->SetSetpoint(lift->getPosition());
liftCount = 0;
}
//if(!(count%50)) printf("Braking/Not PID \n");
}
if(lift->isBraking() && !(count%10)) PIDLift->SetSetpoint(lift->getPosition());
if(fabs(PIDLift->GetError()) < 0.01 && disengageBrake && count - liftCount > 3)
{
disengageBrake = false;
if(liftEncoder->PIDGet() < liftSP) PIDLift->SetPID(LIFTPROPGAIN, LIFTINTGAIN, LIFTDERIVGAIN - 0.015);
else PIDLift->SetPID(LIFTPROPGAIN, LIFTINTGAIN, LIFTDERIVGAIN + 0.015);
liftCount = 0;
}
//pid
/*
else if(!(fabs(PIDLift->GetError()) < 0.04) && !lift->isBraking() && liftPos == -20)
{
PIDLift->Enable();
liftPos = -10;
printf("PID GO PID GO PID GO PID GO PID GO \n");
}
*/
//when liftPos is positive, measures position
//when liftPos = -10, is pidding
//when liftPos = -20, has just released brake
}
else //(MODESWITCH)
{
if(PIDLift->IsEnabled()) PIDLift->Reset();
liftPower = .8*pow(2*((log(LIFTSLIDER + 0.003/.0208116511)/LOG17) + 0.116), 2)*(2*((log(LIFTSLIDER + 0.003/.0208116511)/LOG17) + 0.116)/fabs(2*((log(LIFTSLIDER + 0.003/.0208116511)/LOG17) + 0.116)));
liftPowerAbs = fabs(liftPower);
if(liftPowerAbs > 1) liftPower /= liftPowerAbs;
//if(!(count%5)) printf("Slider: %f", liftPower);
if(lift->isBraking() && liftPowerAbs > 0.05) lift->brakeOff();
else if(!lift->isBraking() && liftPowerAbs <= 0.05 && !(count%5)) lift->brakeOn();
if (liftPowerAbs > 0.05)
{
liftMotor1->Set(liftPower);
liftMotor2->Set(liftPower);
}
else
{
liftMotor1->Set(0);
liftMotor2->Set(0);
}
}
if(MODESWITCH && LIFTLOW1BUTTON && LIFTMID1BUTTON && LIFTHIGH1BUTTON) liftEncoder->Reset();
/*
if(!(count%5))
{
printf("Lift pos: %f Lift error: %f Lift SP: %f \n", liftPIDSource->PIDGet(),
PIDLift->GetError(), PIDLift->GetSetpoint());
}
*/
if(!(count%5) && MODESWITCH && GRIPPERPOSUP && GRIPPERPOSDOWN && GRIPPERPOP)
{
gripPIDOn = !gripPIDOn;
printf("Switch'd\n");
}
if(gripPIDOn)
{
if(!PIDGrip->IsEnabled()) PIDGrip->Enable();
if(GRIPPERPOSUP && !GRIPPERPOSDOWN)
{
goalGripSP = 0;
}
else if(GRIPPERPOSDOWN && !GRIPPERPOSUP && lift->getPosition() < 0.5)
{
goalGripSP = 1;
}
/*
else if(!GRIPPERPOSDOWN && !GRIPPERPOSUP)
{
goalGripSP = 0.5;
}
*/
gripError = PIDGrip->GetError();
gripErrorAbs = fabs(gripError);
PIDGrip->SetSetpoint(goalGripSP);
if(gripErrorAbs < 0.4) PIDGrip->SetOutputRange(-0.4, 0.6); //negative is up
else PIDGrip->SetOutputRange(-0.9, 0.8); //negative is up
if(gripErrorAbs > 0.0 && gripErrorAbs < 0.2)
{
PIDGrip->SetPID(GRIPPROPGAIN - 1.25*(1 - gripErrorAbs) + gripPropMod, GRIPINTGAIN + gripIntMod, 0.3 + 0.1*(1 - gripPIDSource->PIDGet()));
}
else
{
PIDGrip->SetPID(GRIPPROPGAIN - 1.*(1 - gripErrorAbs) + gripPropMod, 0, 0.02);
}
if(fabs(gripPIDSource->PIDGet()) < 0.03 && PIDGrip->GetSetpoint() == 0)
{
gripLatch1->Set(true);
gripLatch2->Set(false);
}
else if(!(gripLatch1->Get() && PIDGrip->GetSetpoint() == 0) ||
gripPIDSource->PIDGet() < 0)
{
gripLatch1->Set(false);
gripLatch2->Set(true);
}
if(gripLatch1->Get() && !(count%20))
{
PIDGrip->Reset();
PIDGrip->Enable();
}
/*
if(stickL.GetRawButton(1) && !(count%5)){
gripIntMod -= 0.001;
}
if(stickR.GetRawButton(1) &&!(count%5))
{
gripIntMod += 0.001;
}
if(stickL.GetRawButton(2) && !(count%5))
{
gripPropMod -= 0.1;
}
if(stickL.GetRawButton(3) && !(count%5))
{
gripPropMod += 0.1;
}
*/
/*
if(LIFTBOTTOMBUTTON)
{
PIDGrip->Reset();
PIDGrip->Enable();
}
*/
if(!(count%5))
{
printf("Gripper pos: %f Gripper error: %f Grip power: %f \n",
gripPIDSource->PIDGet(), PIDGrip->GetError(), gripMotor1->Get());
}
}
//Calibration routine
else
{
if(gripLatch1->Get() == true)
{
gripLatch1->Set(false);
gripLatch2->Set(true);
}
if(PIDGrip->IsEnabled()) PIDGrip->Reset();
if(GRIPPERPOSUP)
{
gripMotor1->Set(-0.5);
//gripMotor2->Set(0.5);
}
else if(GRIPPERPOSDOWN)
{
gripMotor1->Set(0.5);
//gripMotor2->Set(-0.5);
}
else
{
gripMotor1->Set(0);
//gripMotor2->Set(0);
}
}
//if(!(count%5)) printf("Grip volts: %f \n", gripPot->GetVoltage());
//if(!(count%5)) printf("Grip 1 voltage: %f \n", gripMotor1->Get());
if(GRIPPEROPEN && !popStage)
{
#if !(INNERGRIP)
gripOpen1->Set(true);
gripOpen2->Set(false);
#else
gripOpen1->Set(false);
gripOpen2->Set(true);
#endif
}
else if(!popStage)
{
#if !(INNERGRIP)
gripOpen1->Set(false);
gripOpen2->Set(true);
#else
gripOpen1->Set(true);
gripOpen2->Set(false);
#endif
}
if(GRIPPERPOP && !popStage && goalGripSP == 0 && !(GRIPPEROPEN && GRIPPERCLOSE)) popStage = 1;
if(popStage) popTime = GetClock();
if(popStage == 1)
{
//popCount = count;
popStart = GetClock();
popStage++;
//printf("POP START POP START POP START \n");
}
if(popStage == 2)
{
#if !(INNERGRIP)
gripOpen1->Set(true);
gripOpen2->Set(false);
#else
gripOpen1->Set(false);
gripOpen2->Set(true);
#endif
popStage++;
//printf("GRIP OPEN GRIP OPEN GRIP OPEN \n");
}
if(popStage == 3 && popTime - popStart > 0.0) //used to be 0.15
{
gripPop1->Set(true);
gripPop2->Set(false);
popStage++;
//printf("POP OUT POP OUT POP OUT \n");
}
if(popStage == 4 && popTime - popStart > .75) //time was 0.9
{
gripPop1->Set(false);
gripPop2->Set(true);
popStage++;
//printf("POP IN POP IN POP IN \n");
}
if(popStage == 5 && popTime - popStart > 0.9) popStage = 0; //time was 1.05
if(MINIBOTSWITCH && !(MODESWITCH && stickR.GetRawButton(1) && stickL.GetRawButton(1))) miniDep->Set(miniDep->kReverse);
else if(MINIBOTSWITCH && MODESWITCH && stickR.GetRawButton(1) && stickL.GetRawButton(1)) miniDep->Set(miniDep->kOn);
#endif
if(!compSwitch->Get()) compressor->Set(compressor->kReverse);
else compressor->Set(compressor->kOff);
/*
if(stickR.GetRawButton(1)) compressor->Set(compressor->kReverse);
else compressor->Set(compressor->kForward);
*/
Wait(0.02); // wait for a motor update time
}
}
void OperatorControl()
{
compressor.Start();
myRobot.SetSafetyEnabled(true);
myRobot.SetInvertedMotor(myRobot.kRearLeftMotor, true);//Invert rear left Motor
myRobot.SetInvertedMotor(myRobot.kRearRightMotor, true);//Invert rear right motor
myRobot.SetInvertedMotor(myRobot.kFrontLeftMotor, true);//Invert rear right motor
myRobot.SetInvertedMotor(myRobot.kFrontRightMotor, true);
DriverStation *ds;
DriverStationLCD *dsLCD;
ds = DriverStation::GetInstance();
dsLCD = DriverStationLCD::GetInstance();
dsLCD->Printf(DriverStationLCD::kUser_Line1,1, "Starting Teleop");
dsLCD->UpdateLCD();
while (true)
{
if (!compressor.GetPressureSwitchValue()){
compressor.Start();
}
myRobot.ArcadeDrive(stick);
/*PNEUMATIC CODE*/
if (stick.GetRawButton(8)){
shooterSole.Set(shooterSole.kForward);
}
if (stick.GetRawButton(1)){
shooterSole.Set(shooterSole.kReverse);
}
/*SHOOTER CODE*/
if (stick.GetRawButton(2)){
shooter.SetSpeed(1);
}
if (stick.GetRawButton(4)){
shooter.SetSpeed(-1);
dsLCD->Printf(DriverStationLCD::kUser_Line1,(int)forklift.Get(), "Shooter Should be negative");
dsLCD->UpdateLCD();
}
if (!stick.GetRawButton(4) || !stick.GetRawButton(2)){
shooter.SetSpeed(0);
}
/* FORKLIFT CODE*/
if (!stick.GetRawButton(5) || !stick.GetRawButton(6)){
forklift.SetSpeed(0);
}
if (stick.GetRawButton(5)){
forklift.SetSpeed(1);
}
if (stick.GetRawButton(6)){
forklift.SetSpeed(-1);
dsLCD->Printf(DriverStationLCD::kUser_Line1,(int)forklift.Get(), "Forklift Should be negative");
dsLCD->UpdateLCD();
}
if (!shoot.Get()){
shooter.SetSpeed(0);
shooterSole.Set(shooterSole.kForward);
}
if (stick.GetRawButton(11)){
//myRobot.m_rearLeftMotor.SetSpeed(1);
//myRobot.m_rearRightMotor.SetSpeed(1);
//myRobot.m_frontLeftMotor.SetSpeed(1);
//myRobot.m_frontRightMotor.SetSpeed(1);
}
//Wait(0.005);// wait for a motor update time
}
}