//bus pirate initialization
//setup clock, terminal UART, pins, LEDs, and display version info
void Initialize(void){
CLKDIVbits.RCDIV0=0; //clock divider to 0
AD1PCFG = 0xFFFF; // Default all pins to digital
OSCCONbits.SOSCEN=0;
BP_LEDMODE_DIR=0; //MODE LED output
IODIR|=(AUX+MOSI+CLK+MISO+CS);//AUX, MOSI, CLK, MISO, CS pins to input
IOLAT&=(~AUX+MOSI+CLK+MISO+CS); //low pin
//modify setup behavior according to defines in base.h
#ifdef BUSPIRATEV2 //only for v2 and v3, not v1a or v0a
#if defined(ENABLE_PULLUP_RESISTORS)
BP_PULLUP_ON(); //enable pullups
#else
BP_PULLUP_OFF();//disable pullups
#endif
#endif
#if defined(ENABLE_VREG)
BP_VREG_ON(); //enable vreg
#else
BP_VREG_OFF(); //disable vreg
#endif
//set pin configuration using peripheral pin select
BP_TERM_RX=BP_TERM_RX_RP; //Inputs UART1 RX RPINR18bits.U1RXR=4;
BP_TERM_TX_RP=BP_TERM_TX; // Outputs UART1 TX RPOR1bits.RP3R=U1TX_IO;
}
void binIOperipheralset(unsigned char inByte){
if(inByte&0b1000){
BP_VREG_ON();//power on
}else{
BP_VREG_OFF();//power off
}
#ifndef BUSPIRATEV1A
if(inByte&0b100){
BP_PULLUP_ON();//pullups on
}else{
BP_PULLUP_OFF();
}
#endif
#if defined(BUSPIRATEV1A)
if(inByte&0b100){
BP_AUX2_HI();//AUX2 control
}else{
BP_AUX2_LOW();
}
#endif
//AUX pin, high/low only
if(inByte&0b10){
BP_AUX0_DIR=0;//aux output
BP_AUX0=1;//aux high
}else{
BP_AUX0_DIR=0;//aux output
BP_AUX0=0;//aux low
}
//CS pin, follows HiZ setting
if(inByte&0b1){
if(modeConfig.HiZ==1){
IODIR|=CS; //CS iput in open drain mode
}else{
IOLAT|=CS; //CS high
IODIR&=(~CS); //CS output
}
}else{
IOLAT&=(~CS); //BP_CS=0;
IODIR&=(~CS); //CS output
}
//UART1TX(1);//send 1/OK
}
//self test, showProgress=1 displays the test results in the terminal, set to 0 for silent mode
//errors are counted in the global errors variable
//returns number of errors
unsigned char selfTest(unsigned char showProgress, unsigned char jumperTest){
//toggle display of test results with show Progress variable
errors=0;
if(!showProgress) bpConfig.quiet=1;
//instructions (skip pause if no display output)
if(showProgress && jumperTest){
//bpPOSTWline("Disconnect any devices");
//bpPOSTWline("Connect (Vpu to +5V) and (ADC to +3.3V)");
BPMSG1163;
BPMSG1251; // //bpPOSTWline("Press a key to start");
//JTR Not required while(!UART1RXRdy()); //wait for key
UART1RX();//discard byte
}
//bpPOSTWline("Ctrl");
BPMSG1164;
BP_AUX0=1;
BP_AUX0_DIR=0;
//bpPOSTWstring("AUX");
BPMSG1165;
bpTest(BP_AUX0,1);
BP_AUX0=0;
BP_AUX0_DIR=1;
BP_LEDMODE=1;
BP_LEDMODE_DIR=0;
//bpPOSTWstring("MODE LED");
BPMSG1166;
bpTest(BP_LEDMODE,1);
BP_LEDMODE=0;
BP_PULLUP_ON();
//bpPOSTWstring("PULLUP H");
BPMSG1167;
bpTest(BP_PULLUP,1);
BP_PULLUP_OFF();
//bpPOSTWstring("PULLUP L");
BPMSG1168;
bpTest(BP_PULLUP,0);
BP_VREG_ON();
bpDelayMS(2);//in silent mode there's not enought delay for the power supplied to come on
//bpPOSTWstring("VREG");
BPMSG1169;
bpTest(BP_VREGEN,1);
#if defined (BUSPIRATEV4)
BPMSG1265; //bpWline("EEPROM");
BPMSG1266; //bpWstring("SCL");
bpTest(BP_EE_SCL, 1);
BPMSG1267; //bpWstring("SDA");
bpTest(BP_EE_SDA, 1);
BPMSG1268; //bpWstring("WP");
bpTest(BP_EE_WP, 1);
BPMSG1269; //bpWstring("ACK");
bpTest(eetest(), 0);
#endif
//ADC check
//bpPOSTWline("ADC and supply");
BPMSG1170;
ADCON(); // turn ADC ON
#if defined (BUSPIRATEV4)
BPMSG1270; //bpWstring("Vusb");
bpADCPinTest(BP_ADC_USB,V5L, V5H);
//bpPOSTWstring("5V");
BPMSG1171;
bpADCPinTest(BP_ADC_5V0,V5L, V5H);
//enable 5v0 pullup and test
BP_5VPU_ON();
BPMSG1171; //bpWstring("5V0 VPU");
bpWstring(" ");
BPMSG1172; //VPU
bpDelayMS(2);
bpADCPinTest(BP_ADC_VPU,V5L, V5H);
BP_5VPU_OFF();
//ADC test (3.3 volts)
if(jumperTest){
//ADC is connected to 3.3 volts
//bpPOSTWstring("ADC");
BPMSG1174;
bpADCPinTest(BP_ADC_PROBE,V33L, V33H);
}
//bpPOSTWstring("3.3V");
BPMSG1173;
bpADCPinTest(BP_ADC_3V3,V33L, V33H);
//enable 3v3 pullup and test
BP_3V3PU_ON();
BPMSG1173; //bpWstring("3V3 VPU");
bpWstring(" ");
BPMSG1172; //VPU
bpDelayMS(2);
bpADCPinTest(BP_ADC_VPU,V33L, V33H);
BP_3V3PU_OFF();
#elif defined (BUSPIRATEV3)
//v3 test
//0x030F is 5volts
//bpPOSTWstring("5V");
BPMSG1171;
bpADCPinTest(BP_ADC_5V0,V5L, V5H);
if(jumperTest){
//Vpullup is connected to 5volts
//bpPOSTWstring("VPU");
BPMSG1172;
bpADCPinTest(BP_ADC_VPU,V5L, V5H);
}
//0x0208 is 3.3volts
//bpPOSTWstring("3.3V");
BPMSG1173;
bpADCPinTest(BP_ADC_3V3,V33L, V33H);
if(jumperTest){
//ADC is connected to 3.3volts
//bpPOSTWstring("ADC");
BPMSG1174;
bpADCPinTest(BP_ADC_PROBE,V33L, V33H);
}
#endif
ADCOFF(); // turn ADC OFF
//*************
//
// Test bus pins three ways, also tests on-board pullup resistors:
// 1. normal/high, 2. open collector ground, 3. open collector high.
//
//***************
//pullup off, pins=output & high, read input, high?
//bpPOSTWline("Bus high");
BPMSG1175;
IODIR&= ~(ALLIO);//output
IOLAT|=ALLIO; //high
bpDelayMS(100);
bpBusPinsTest(1);
//pullup on, pins=output & low, read input, low?
//bpPOSTWline("Bus Hi-Z 0");
BPMSG1176;
IOLAT&= ~(ALLIO); //low
if(jumperTest){
#if defined (BUSPIRATEV4)
BP_3V3PU_ON();
#endif
BP_PULLUP_ON();
}
bpDelayMS(100);
bpBusPinsTest(0);
if(jumperTest){
//pullup on, pins=input & low, read input, high?
//bpPOSTWline("Bus Hi-Z 1");
BPMSG1177;
IODIR|=ALLIO;//output
bpDelayMS(100);
bpBusPinsTest(1);
#if defined (BUSPIRATEV4)
BP_3V3PU_OFF();
#endif
}
//instructions (skip pause if no display output)
if(showProgress && jumperTest){
BP_VREG_ON();
BP_MODELED_ON();
//bpPOSTWline("MODE and VREG LEDs should be on! Any key exits.");
#if defined (BUSPIRATEV4)
BP_USBLED_ON();
#endif
BPMSG1178;
BPMSG1250;
//JTR Not required while(!UART1RXRdy());
UART1RX();
#ifdef BUSPIRATEV4
BP_USBLED_OFF();
#endif
BP_MODELED_OFF();
BP_VREG_OFF();
}
bpInit();//clean up
BPMSG1179;
bpWdec(errors);
BPMSG1180;
bpConfig.quiet=0;
return errors;
}
void binpic(void)
{ unsigned char cmd;
int ok;
unsigned int temp;
bpWstring("PIC1");
modeConfig.HiZ=1; // to allow different Vcc
bbL(MOSI|CLK, PICSPEED); // pull both pins to 0 before applying Vcc and Vpp
picmode=PICMODE6;
piccmddelay=2;
while(1)
{ cmd=UART1RX();
switch(cmd&0xC0)
{ case 0x00: ok=1;
switch(cmd&0xF0)
{ case 0x00: switch(cmd)
{ case 0x00: return;
case 0x01: bpWstring("PIC1");
break;
case 0x02: picmode=PICMODE6;
break;
case 0x03: picmode=PICMODE4;
break;
case 0x04:
case 0x05:
case 0x06:
case 0x07: piccmddelay=(cmd-0x04);
break;
default: ok=0;
}
break;
case 0x10: if(cmd&0x08)
{ if(cmd&0x04)
{ bbH(AUX ,5);
}
else
{ bbL(AUX ,5);
}
if(cmd&0x02)
{ bbH(MISO ,5);
}
else
{ bbL(MISO ,5);
}
if(cmd&0x01)
{ bbH(CS ,5);
}
else
{ bbL(CS ,5);
}
}
else
{ if(cmd&0x04) // pwm?
{ PWMfreq=100;
PWMduty=50;
updatePWM();
}
else
{ PWMfreq=0;
updatePWM();
}
if(cmd&0x02) // vreg on
{ BP_VREG_ON();
//modeConfig.vregEN=1;
}
else
{ BP_VREG_OFF();
//modeConfig.vregEN=0;
}
if(cmd&0x01) // pullup on
#ifndef BUSPIRATEV1A
{ BP_PULLUP_ON();
// modeConfig.pullupEN=1;
}
else
{ BP_PULLUP_OFF();
// modeConfig.pullupEN=0;
}
#endif
}
break;
default: ok=0;
}
if(ok)
{ UART1TX(1);
}
else
{ UART1TX(0);
}
break;
case 0x40: picmode|=PICCMD;
picwrite(cmd&0x3F);
picmode&=PICMODEMSK;
UART1TX(1);
break;
case 0x80: picmode|=PICCMD;
picwrite(cmd&0x3F);
picmode&=PICMODEMSK;
temp=UART1RX();
temp<<=8;
temp|=UART1RX();
picwrite(temp);
UART1TX(1);
break;
case 0xC0: picmode|=PICCMD;
picwrite(cmd&0x3F);
picmode&=PICMODEMSK;
UART1TX(1);
temp=picread();
UART1TX(temp>>8);
UART1TX(temp&0x0FF);
break;
}
}
}
uint8_t perform_selftest(bool show_progress, bool jumper_test) {
errors = 0;
if (!show_progress) {
bus_pirate_configuration.quiet = true;
}
/* Alert the user to perform the required manual operations if needed. */
if (show_progress && jumper_test) {
/* Print alert. */
BPMSG1163;
BPMSG1251;
/* Wait for a character to come in. */
user_serial_read_byte();
}
/* Start the test procedure. */
BPMSG1164;
/* Check whether AUX0 goes HIGH when requested. */
BP_AUX0 = HIGH;
BP_AUX0_DIR = OUTPUT;
BPMSG1165;
check_result(BP_AUX0, HIGH);
BP_AUX0 = LOW;
BP_AUX0_DIR = INPUT;
/* Check whether the LED line goes HIGH when requested. */
BP_LEDMODE = HIGH;
BP_LEDMODE_DIR = OUTPUT;
BPMSG1166;
check_result(BP_LEDMODE, HIGH);
BP_LEDMODE = LOW;
/* Check whether the pull-up line goes HIGH when requested. */
BP_PULLUP_ON();
BPMSG1167;
check_result(BP_PULLUP, HIGH);
/* Check whether the pull-up line goes LOW when requested. */
BP_PULLUP_OFF();
BPMSG1168;
check_result(BP_PULLUP, LOW);
/* Check whether the regulated voltage line goes HIGH when requested. */
BP_VREG_ON();
bp_delay_ms(PWR_STATE_TEST_DELAY);
BPMSG1169;
check_result(BP_VREGEN, HIGH);
#ifdef BUSPIRATEV4
/* Test the internal EEPROM. */
BPMSG1265;
/* Check the I2C flash clock line. */
BPMSG1266;
check_result(BP_EE_SCL, HIGH);
/* Check the I2C flash data line. */
BPMSG1267;
check_result(BP_EE_SDA, HIGH);
/* Check the I2C flash WRITE PROTECT line. */
BPMSG1268;
check_result(BP_EE_WP, HIGH);
/* Performs a more complete EEPROM test. */
BPMSG1269;
check_result(eeprom_test(), true);
#endif /* BUSPIRATEV4 */
/* ADC check. */
BPMSG1170;
/* Turn ADC on. */
ADCON();
#ifdef BUSPIRATEV4
/* Check whether the voltage coming in from the USB port is within range. */
BPMSG1270;
perform_adc_test(BP_ADC_USB, V5L, V5H);
#endif /* BUSPIRATEV4 */
/* Check whether the +5v rail output is within range. */
BPMSG1171;
perform_adc_test(BP_ADC_5V0, V5L, V5H);
#ifdef BUSPIRATEV4
/* Test the +5v pull-up line. */
BP_5VPU_ON();
BPMSG1171;
bpSP;
BPMSG1172;
bp_delay_ms(PWR_STATE_TEST_DELAY);
perform_adc_test(BP_ADC_VPU, V5L, V5H);
BP_5VPU_OFF();
if (jumper_test) {
/*
* Check whether the +3.3v rail output is within range when measured from
* outside the board circuitry, once a jumper wire is manually placed
* between the +3.3v rail pin and the ADC input pin.
*/
BPMSG1174;
perform_adc_test(BP_ADC_PROBE, V33L, V33H);
}
/*
* Check whether the +3.3v rail output is within range when measured from
* inside the board circuitry.
*/
BPMSG1173;
perform_adc_test(BP_ADC_3V3, V33L, V33H);
/* Test the +3.3v pull-up line. */
BP_3V3PU_ON();
BPMSG1173;
bpSP;
BPMSG1172;
bp_delay_ms(PWR_STATE_TEST_DELAY);
perform_adc_test(BP_ADC_VPU, V33L, V33H);
BP_3V3PU_OFF();
#elif defined(BUSPIRATEV3)
if (jumper_test) {
/*
* Check whether the +5v pull-up output is within range when measured from
* outside the board circuitry, once a jumper wire is manually placed
* between the +5v pull-up pin and the ADC input pin.
*/
BPMSG1172;
perform_adc_test(BP_ADC_VPU, V5L, V5H);
}
/* Check whether the +3.3v rail output is within range. */
BPMSG1173;
perform_adc_test(BP_ADC_3V3, V33L, V33H);
if (jumper_test) {
/*
* Check whether the +3.3v rail output is within range when measured from
* outside the board circuitry, once a jumper wire is manually placed
* between the +3.3v rail pin and the ADC input pin.
*/
BPMSG1174;
perform_adc_test(BP_ADC_PROBE, V33L, V33H);
}
#endif /* BUSPIRATEV4 || BUSPIRATEV3 */
/* Turn ADC off. */
ADCOFF();
/*
* Pull all I/O pins HIGH with pull-ups deactivated, and check the pins
* state afterwards.
*/
BPMSG1175;
IODIR &= ~ALLIO;
IOLAT |= ALLIO;
bp_delay_ms(PIN_STATE_TEST_DELAY);
perform_pins_state_test(HIGH);
/*
* Pull all I/O pins LOW with pull-ups active and check the pins state
* afterwards.
*/
BPMSG1176;
IOLAT &= ~ALLIO;
if (jumper_test) {
#ifdef BUSPIRATEV4
BP_3V3PU_ON();
#endif /* BUSPIRATEV4 */
BP_PULLUP_ON();
}
bp_delay_ms(PIN_STATE_TEST_DELAY);
perform_pins_state_test(LOW);
if (jumper_test) {
/*
* Pull all I/O pins HIGH with pull-ups active and check the pins state
* afterwards.
*/
/* TODO: should this be done without jumpers too? */
BPMSG1177;
IODIR |= ALLIO;
bp_delay_ms(PIN_STATE_TEST_DELAY);
perform_pins_state_test(HIGH);
#ifdef BUSPIRATEV4
BP_3V3PU_OFF();
#endif /* BUSPIRATEV4 */
}
if (show_progress && jumper_test) {
/*
* Alert the user to check the LED on/off states, and prompt for a key
* to be pressed to continue.
*/
BP_VREG_ON();
BP_MODELED_ON();
#ifdef BUSPIRATEV4
BP_USBLED_ON();
#endif /* BUSPIRATEV4 */
BPMSG1178;
MSG_ANY_KEY_TO_EXIT_PROMPT;
user_serial_read_byte();
#ifdef BUSPIRATEV4
BP_USBLED_OFF();
#endif /* BUSPIRATEV4 */
BP_MODELED_OFF();
BP_VREG_OFF();
}
bp_reset_board_state();
BPMSG1179;
bp_write_dec_byte(errors);
BPMSG1180;
bus_pirate_configuration.quiet = false;
return errors;
}