/*******************************************************************************
* 名 称： Bsp_ConfgiSysClk
* 功 能： 配置CPU系统时钟
* 入口参数： 枚举SYS_CLK_E ； 可选参数为:
* HSI_2M = 0 内部高速RC振荡源16M, 分频倍率设置为 1/8 可得到2M
* HSI_4M, 内部高速RC振荡源16M, 分频倍率设置为 1/4 可得到4M
* HSI_8M, 内部高速RC振荡源16M, 分频倍率设置为 1/2 可得到8M
* HSI_16M, 内部高速RC振荡源16M, 分频倍率设置为 1/1 可得到16M
* LSI_128K, 内部低速RC时钟源，频率固定为128KHz
* HSE_XTAL, 外部高速时钟 (频率由用于外接晶振决定，无分频选项)
* 出口参数： 无
* 作 者： Roger-WY
* 创建日期： 2014-08-20
* 修 改：
* 修改日期：
* 备 注： 建议使用优化代码模式
*******************************************************************************/
void Bsp_ConfgiSysClk(SYS_CLK_E _iSysClk)
{
#if 1 /* 空间不足，优化代码, 只保留需要的时钟设置 */
if (_iSysClk == HSI_16M) {
/* 自动切换, 切换到内部高速时钟HSI, 禁止系统时钟中断, 关闭当前的时钟源 */
CLK_ClockSwitchConfig(CLK_SWITCHMODE_AUTO, CLK_SOURCE_HSI, DISABLE, CLK_CURRENTCLOCKSTATE_DISABLE);
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1); /* 设置内部高速RC时钟HSI为时钟源，分频系数为1 */
while (CLK_GetFlagStatus(CLK_FLAG_HSIRDY) == RESET); /* 等待HSI时钟稳定 */
}
#else
switch (_iSysClk) {
case HSE_XTAL:
/* 自动切换, 切换到外部高速时钟HSE, 禁止系统时钟中断, 关闭当前的时钟源 */
CLK_ClockSwitchConfig(CLK_SWITCHMODE_AUTO, CLK_SOURCE_HSE, DISABLE, CLK_CURRENTCLOCKSTATE_DISABLE);
break;
case LSI_128K:
/* 自动切换, 切换到内部低速时钟LSI, 禁止系统时钟中断, 关闭当前的时钟源 */
CLK_ClockSwitchConfig(CLK_SWITCHMODE_AUTO, CLK_SOURCE_LSI, DISABLE, CLK_CURRENTCLOCKSTATE_DISABLE);
break;
case HSI_16M:
/* 自动切换, 切换到内部高速时钟HSI, 禁止系统时钟中断, 关闭当前的时钟源 */
CLK_ClockSwitchConfig(CLK_SWITCHMODE_AUTO, CLK_SOURCE_HSI, DISABLE, CLK_CURRENTCLOCKSTATE_DISABLE);
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1); /* 设置内部高速RC时钟HSI为时钟源，分频系数为1 */
while (CLK_GetFlagStatus(CLK_FLAG_HSIRDY) == RESET); /* 等待HSI时钟稳定 */
break;
case HSI_8M:
/* 自动切换, 切换到内部高速时钟HSI, 禁止系统时钟中断, 关闭当前的时钟源 */
CLK_ClockSwitchConfig(CLK_SWITCHMODE_AUTO, CLK_SOURCE_HSI, DISABLE, CLK_CURRENTCLOCKSTATE_DISABLE);
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV2); /* 设置内部高速RC时钟HSI为时钟源，分频系数为2 */
while (CLK_GetFlagStatus(CLK_FLAG_HSIRDY) == RESET); /* 等待HSI时钟稳定 */
break;
case HSI_4M:
/* 自动切换, 切换到内部高速时钟HSI, 禁止系统时钟中断, 关闭当前的时钟源 */
CLK_ClockSwitchConfig(CLK_SWITCHMODE_AUTO, CLK_SOURCE_HSI, DISABLE, CLK_CURRENTCLOCKSTATE_DISABLE);
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV4); /* 设置内部高速RC时钟HSI为时钟源，分频系数为4 */
while (CLK_GetFlagStatus(CLK_FLAG_HSIRDY) == RESET); /* 等待HSI时钟稳定 */
break;
case HSI_2M:
/* 自动切换, 切换到内部高速时钟HSI, 禁止系统时钟中断, 关闭当前的时钟源 */
CLK_ClockSwitchConfig(CLK_SWITCHMODE_AUTO, CLK_SOURCE_HSI, DISABLE, CLK_CURRENTCLOCKSTATE_DISABLE);
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV8); /* 设置内部高速RC时钟HSI为时钟源，分频系数为8 */
while (CLK_GetFlagStatus(CLK_FLAG_HSIRDY) == RESET); /* 等待HSI时钟稳定 */
break;
default:
break;
}
#endif
}
/**
* @brief Example main entry point.
* @par Parameters:
* None
* @retval
* None
*/
void main(void)
{
u8 i = 0;
u16 Timer2Count;
/* Configuration of the GPIO*/
GPIO_Configuration();
/* Clock divider to HSI/1 */
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
/* BEEP calibration */
BEEP_LSICalibrationConfig(LSIMeasurment());
/* TS Library Initialisation */
TSL_Init();
/* TS Application Initialisation */
ExtraCode_Init();
/* Tim2 Configuration */
InitializeTim2();
while (1)
{
ExtraCode_StateMachine();
TSL_Action();
BeepDriver_Action();
//SubCounterSounds();
}
}
/**
******************************************************************************
* @brief Configures clocks
* @par Parameters:
* None
* @retval void None
* @par Required preconditions:
* None
******************************************************************************
*/
void CLK_Configuration(void)
{
/* Fmaster = 16MHz */
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
}
/**
* @brief Example firmware main entry point.
* @par Parameters:
* None
* @retval
* None
*/
void main(void)
{
/*High speed internal clock prescaler: 1*/
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
/* Enable general interrupts */
enableInterrupts();
/* Deinitializes the UART1 and UART3 peripheral */
UART1_DeInit();
UART3_DeInit();
/* UART1 and UART3 configuration -------------------------------------------------*/
/* UART1 and UART3 configured as follow:
- BaudRate = 9600 baud
- Word Length = 8 Bits
- One Stop Bit
- No parity
- Receive and transmit enabled
- UART1 Clock disabled
*/
/* Configure the UART1 */
UART1_Init((u32)9600, UART1_WORDLENGTH_8D, UART1_STOPBITS_1, UART1_PARITY_NO, UART1_SYNCMODE_CLOCK_DISABLE, UART1_MODE_TXRX_ENABLE);
/* Configure the UART3 */
UART3_Init((u32)9600, UART3_WORDLENGTH_8D, UART3_STOPBITS_1, UART3_PARITY_NO, UART3_MODE_TXRX_ENABLE);
/* Enable UART3 Receive and UART1 Transmit interrupt */
UART3_ITConfig(UART3_IT_RXNE_OR, ENABLE);
UART1_ITConfig(UART1_IT_TXE, ENABLE);
/* Wait until end of transmission from UART1 to UART3 */
while (GetVar_RxCounter2() < GetVar_NbrOfDataToTransfer1())
{
}
/* Enable UART1 Receive and UART3 Transmit interrupt */
UART1_ITConfig(UART1_IT_RXNE_OR, ENABLE);
UART3_ITConfig(UART3_IT_TXE, ENABLE);
/* Wait until end of transmission from UART3 to UART1 */
while (GetVar_RxCounter1() < GetVar_NbrOfDataToTransfer2())
{
}
/* Check the received data with the send ones */
TransferStatus1 = Buffercmp(TxBuffer2, RxBuffer1, RxBufferSize1);
/* TransferStatus1 = PASSED, if the data transmitted from UART3 and
received by UART1 are the same */
/* TransferStatus1 = FAILED, if the data transmitted from UART3 and
received by UART1 are different */
TransferStatus2 = Buffercmp(TxBuffer1, RxBuffer2, RxBufferSize2);
/* TransferStatus2 = PASSED, if the data transmitted from UART1 and
received by UART3 are the same */
/* TransferStatus2 = FAILED, if the data transmitted from UART1 and
received by UART3 are different */
while (1);
}
/**
* @brief Configure system clock to run at 16Mhz and output the system clock on
* CCO pin
* @param None
* @retval None
*/
static void CLK_Config(void)
{
CLK_DeInit();
/* Clock divider to HSI/1 */
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
/* Output Fcpu on CLK_CCO pin */
CLK_CCOConfig(CLK_OUTPUT_MASTER);
}
/**
* @brief Configure system clock to run at 16Mhz
* @param None
* @retval None
*/
void CLK_Config(void)
{
/* Initialization of the clock */
/* Clock divider to HSI/1 */
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
CLK_SYSCLKConfig(CLK_PRESCALER_CPUDIV1);
CLK_HSICmd(ENABLE);
CLK_PeripheralClockConfig(CLK_PERIPHERAL_TIMER1, ENABLE);
CLK_PeripheralClockConfig(CLK_PERIPHERAL_TIMER2, ENABLE);
CLK_PeripheralClockConfig(CLK_PERIPHERAL_TIMER3, ENABLE);
CLK_PeripheralClockConfig(CLK_PERIPHERAL_TIMER4, ENABLE);
CLK_PeripheralClockConfig(CLK_PERIPHERAL_UART1, ENABLE);
#ifdef __DEBUG__
CLK_PeripheralClockConfig(CLK_PERIPHERAL_UART3, ENABLE);
#endif
}
int main(void) {
// Set the internal high-speed oscillator to 1 to run at 16/1=16MHz.
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
// Reset ("de-initialise") GPIO port D.
GPIO_DeInit(GPIOD);
// Initialise pin 0 of port D by setting it as:
// - an output pin,
// - using a push-pull driver,
// - at a low logic level (0V), and
// - 10MHz.
GPIO_Init(GPIOD, GPIO_PIN_0, GPIO_MODE_OUT_PP_LOW_FAST);
UART2_DeInit();
/* UART2 configuration ------------------------------------------------------*/
/* UART2 configured as follow:
- BaudRate = 9600 baud
- Word Length = 8 Bits
- One Stop Bit
- Even parity
- Receive and transmit enabled
- UART2 Clock disabled
*/
/* Configure the UART2 */
UART2_Init((u32)9600, UART2_WORDLENGTH_8D, UART2_STOPBITS_1, UART2_PARITY_NO,
UART2_SYNCMODE_CLOCK_DISABLE, UART2_MODE_TXRX_ENABLE);
LCDInit();
DrawScreen();
UpdateLCD();
UART2_ITConfig(UART2_IT_RXNE, ENABLE);
enableInterrupts();
// Infinite loop.
for(;;) {
DrawDemo();
Delay(80);
}
}
/********************************************************************************
* clk_setup *
********************************************************************************/
void _Device_System_clk_setup(void)
{
CLK_HSIPrescalerConfig(dSourceFreqDivided); // fMaster, speed 16MHz / 4 = 4MHz, for peripheral device
CLK_SYSCLKConfig(dMCUFreqDivided); // CPU speed, 4MHz / 1 = 4MHz
// I2C
//CLK_PeripheralClockConfig(CLK_PERIPHERAL_I2C, ENABLE);
// V_BAT, T_SENSOR, I_CHARGE, I_DISCHARGE
CLK_PeripheralClockConfig(CLK_PERIPHERAL_ADC, ENABLE);
// LED 1 ~ 4, PWM
CLK_PeripheralClockConfig(CLK_PERIPHERAL_TIMER1, ENABLE);
// LED 0, PWM
CLK_PeripheralClockConfig(CLK_PERIPHERAL_TIMER2, ENABLE);
// tick
CLK_PeripheralClockConfig(CLK_PERIPHERAL_TIMER4, ENABLE);
// UART
CLK_PeripheralClockConfig(CLK_PERIPHERAL_UART2, ENABLE);
// GPIO_Init(GPIOD, GPIO_PIN_0, GPIO_MODE_OUT_PP_LOW_FAST);
// CLK_CCOConfig(CLK_OUTPUT_CPUDIV8);
// CLK_CCOConfig(CLK_OUTPUT_CPU);
// CLK_CCOCmd(ENABLE);
/* Output Fcpu on CLK_CCO pin */
//CLK_CCOConfig(CLK_OUTPUT_CPU);
//
// //Lsi
// unsigned char status;
// CLK_ClockSwitchCmd(ENABLE);
// status = CLK_ClockSwitchConfig(CLK_SWITCHMODE_AUTO, CLK_SOURCE_LSI, DISABLE, CLK_CURRENTCLOCKSTATE_DISABLE);
//
// while(status == 0);
//CLK_ClockSwitchConfig(CLK_SWITCHMODE_MANUAL, CLK_SOURCE_LSI, DISABLE, CLK_CURRENTCLOCKSTATE_DISABLE);
//CLK_LSICmd(ENABLE);
//CLK_HSECmd(DISABLE);
// //hsi
// CLK_ClockSwitchCmd(ENABLE);
// CLK_HSICmd(ENABLE);
// CLK_LSICmd(DISABLE);
// CLK_ClockSwitchConfig(CLK_SWITCHMODE_AUTO, CLK_SOURCE_HSI, DISABLE, CLK_CURRENTCLOCKSTATE_DISABLE);
}
/**
* @brief Example main entry point.
* @par Parameters:
* None
* @retval
* None
*/
void main(void)
{
/* Initialize SPI for LCD */
SPI_DeInit();
SPI_Init(SPI_FIRSTBIT_MSB, SPI_BAUDRATEPRESCALER_128, SPI_MODE_MASTER, SPI_CLOCKPOLARITY_HIGH, SPI_CLOCKPHASE_2EDGE, SPI_DATADIRECTION_1LINE_TX, SPI_NSS_SOFT, 0x07);
SPI_Cmd(ENABLE);
/* Configure GPIO used to drive the joystick
JOYSTICK_UP --> PB6
JOYSTICK_DOWN --> PB7
JOYSTICK_LEFT --> PB4
*/
GPIO_Init(GPIOB, GPIO_PIN_4 | GPIO_PIN_6 | GPIO_PIN_7, GPIO_MODE_IN_FL_IT);
EXTI_SetExtIntSensitivity(EXTI_PORT_GPIOB, EXTI_SENSITIVITY_FALL_LOW);
enableInterrupts();
/* Initialize LCD */
LCD_Init();
/* Clear LCD lines */
LCD_Clear();
LCD_Backlight(ENABLE);
LCD_PrintString(LCD_LINE1, ENABLE, DISABLE, "Clock Selection");
LCD_PrintString(LCD_LINE2, ENABLE, DISABLE, " Use joystick");
CLK_DeInit();
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
/* Output Fcpu on CLK_CCO pin */
CLK_CCOConfig(CLK_OUTPUT_MASTER);
while (1)
{
}
}
/**
* @brief Example firmware main entry point.
* @par Parameters:
* None
* @retval
* None
*/
void main(void)
{
/*High speed internal clock prescaler: 1*/
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
UART1_DeInit();
/* UART1 configuration ------------------------------------------------------*/
/* UART1 configured as follow:
- BaudRate = 115200 baud
- Word Length = 8 Bits
- One Stop Bit
- No parity
- Receive and transmit enabled
- UART1 Clock disabled
*/
/* Configure UART1 */
UART1_Init((u32)115200, UART1_WORDLENGTH_8D, UART1_STOPBITS_1, UART1_PARITY_NO, UART1_SYNCMODE_CLOCK_DISABLE, UART1_MODE_TXRX_ENABLE);
/* Output a message on Hyperterminal using printf function */
printf("\n\rUART1 Example :Retarget the C library printf function to the UART1\n\r");
while (1);
}
//Modbus Initialization
void Modbus_Init(void)
{
//Clock divider equals 1.Clock 16MHz
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
//Clear bits
TIM2_DeInit();
GPIO_DeInit(GPIOA);
UART2_DeInit();
//Peripetial Initialization
TIM2_TimeBaseInit(TIM2_PRESCALER_2048, 78);
GPIO_Init(GPIOA, GPIO_PIN_3, GPIO_MODE_OUT_PP_LOW_FAST);
UART2_Init(BAUDRATE, UART2_WORDLENGTH_8D, UART2_STOPBITS_2,UART2_PARITY_NO,UART2_SYNCMODE_CLOCK_DISABLE,UART2_MODE_TXRX_ENABLE );
//Enable Periphs
TIM2_Cmd(ENABLE);
UART2_Cmd(ENABLE);
//Interrupt configuration
TIM2_ITConfig(TIM2_IT_UPDATE, ENABLE);
UART2_ITConfig(UART2_IT_RXNE_OR, ENABLE);
#ifndef __DELAY_EN
#define __MODBUS_EN
enableInterrupts();
#endif
}
void main(void) {
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1); // 16Mhz
wl315_init();
flash_init();
uart_init();
// recovery the key value
flash_read_key(LEARN_KEY1, &tKey1);
flash_read_key(LEARN_KEY2, &tKey2);
flash_read_key(LEARN_KEY3, &tKey3);
flash_read_key(LEARN_KEY4, &tKey4);
WL315_START();
rim();
/* Infinite loop */
while (1) {
wl315_learn_task(); // 按键学习任务
uart_print_task(); // 串口打印任务
}
}
void main(void)
{
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
Delay_Init();
RS485_Init(115200);
#if DEBUG
// UART_Init(115200);
#endif
SRF05_Init();
SRF05_AutoPoolEnable();
//flash_read_buffer((char *)&my_data, sizeof (struct flash_data));
my_data.id = 0x21;
// UART_SendByte(0x21, HEX);
// RS485_SendStr("Hello world.\n");
// LED run
GPIO_Init(LED_RUN_PORT, LED_RUN_PIN, GPIO_MODE_OUT_PP_HIGH_FAST);
GPIO_WriteHigh(LED_RUN_PORT, LED_RUN_PIN);
while (1)
{
if (Millis() - tmp_time > 500)
{
LED_RUN_TOGGLE;
tmp_time = Millis();
#if DEBUG
RS485_DIR_OUTPUT;
RS485_SendStr("\n");
RS485_SendFloat(SRF05_GetDistance());
RS485_DIR_INPUT;
#endif
}
if (GPIO_ReadInputPin(RS485_SEL_PORT, RS485_SEL_PIN) == RESET)
{
if (RS485_Available() >= 8)
{
// memset(packet_buff, 0, PACKET_BUFFER_SIZE);
packet_len = RS485_GetData(packet_buff);
packet = (struct Packet *)packet_buff;
if (packet_len < 4 + getTypeLength(packet->data_type))
{
// not enough length
}
else
{
switch (packet->cmd)
{
case CMD_QUERY:
if (packet->id == my_data.id)
{
LED_RUN_TOGGLE;
tmp_distance = SRF05_GetDistance();
packet->data_type = TYPE_FLOAT | BIG_ENDIAN_BYTE_ORDER;
memcpy(packet->data, &tmp_distance, getTypeLength(packet->data_type));
packet->data[getTypeLength(packet->data_type)] = checksum((char *)packet);
RS485_DIR_OUTPUT;
RS485_SendData(packet_buff, 4 + getTypeLength(packet->data_type));
RS485_DIR_INPUT;
}
else if (IS_BROADCAST_ID(packet->id))
{
// if (GPIO_ReadInputPin(RS485_SEL_PORT, RS485_SEL_PIN) == RESET)
// {
LED_RUN_TOGGLE;
packet->id = my_data.id;
tmp_distance = SRF05_GetDistance();
packet->data_type = TYPE_FLOAT | BIG_ENDIAN_BYTE_ORDER;
memcpy(packet->data, &tmp_distance, getTypeLength(packet->data_type));
packet->data[getTypeLength(packet->data_type)] = checksum((char *)packet);
RS485_DIR_OUTPUT;
RS485_SendData(packet_buff, 4 + getTypeLength(packet->data_type));
RS485_DIR_INPUT;
// }
}
else
{
// not own id
}
break;
case CMD_CONTROL:
// by default, this mode used only for setting id
// the id stored on the first bytes of data bytes
if (IS_BROADCAST_ID(packet->id))
{
LED_RUN_TOGGLE;
if (IS_SENSOR_ULTRA_SONIC(packet->data[0]))
{
my_data.id = packet->data[0];
}
}
break;
default:
break;
}
RS485_Flush();
}
}
}
else
{
RS485_Flush();
}
SRF05_ProcessTrigger();
}
}
void main(void)
{
//CFG->GCR |= 0x01; //disable swim pin
/* Configure the Fcpu to DIV1*/
CLK_SYSCLKConfig(CLK_PRESCALER_CPUDIV1);
/* select Clock = 16 MHz */
CLK_SYSCLKConfig(CLK_PRESCALER_HSIDIV1);
/* Configure the system clock to use HSI clock source and to run at 16Mhz */
CLK_ClockSwitchConfig(CLK_SWITCHMODE_AUTO, CLK_SOURCE_HSI, DISABLE, CLK_CURRENTCLOCKSTATE_DISABLE);
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
CLK_HSICmd(ENABLE);
FLASH_Config();
EXTI_DeInit();
//You should add:
// Define FLASH programming time
//FLASH_SetProgrammingTime(FLASH_PROGRAMTIME_STANDARD);
//optbyte1 = FLASH_ReadOptionByte(0x4803); //255 by def
//optbyte2 = FLASH_ReadOptionByte(0x4804); //255 by def
/*
if (optbyte != 765)
{
FLASH_Unlock(FLASH_MEMTYPE_DATA); // unlock data memory by passing the RASS key in the proper order
FLASH_ProgramOptionByte(0x4803, 0xFD); // byte OPT2 resides at address x4803, write a 1 to bit 7. This will also write to the NOPT2 complement byte
FLASH_Lock(FLASH_MEMTYPE_DATA); // re-lock data memory
}
*/
//General purpose timer
TIM4_Config();
#ifdef DFS_90
HotAir_Config();
#endif
#ifndef DFS_90
GPIO_Init(CONTROL_GPIO_PORT, CONTROL_GPIO_PIN, GPIO_MODE_OUT_PP_LOW_FAST);
#endif
Temperature_ADC_Config();
STM_EVAL_SEGInit(SEG1);
STM_EVAL_SEGInit(SEG2);
STM_EVAL_SEGInit(SEG3);
STM_EVAL_LEDInit(LEDA);
STM_EVAL_LEDInit(LEDB);
STM_EVAL_LEDInit(LEDC);
STM_EVAL_LEDInit(LEDD);
STM_EVAL_LEDInit(LEDE);
STM_EVAL_LEDInit(LEDF);
STM_EVAL_LEDInit(LEDG);
STM_EVAL_LEDInit(LEDP);
#ifndef SOLDERING_VAR2
//STM_EVAL_LEDInit(LEDP);
#endif
// STM_EVAL_SEGOn(SEG1);
// STM_EVAL_SEGOn(SEG2);
// STM_EVAL_SEGOn(SEG3);
//
// STM_EVAL_LEDOn(LEDA);
// STM_EVAL_LEDOn(LEDB);
// STM_EVAL_LEDOn(LEDC);
// STM_EVAL_LEDOn(LEDD);
// STM_EVAL_LEDOn(LEDE);
// STM_EVAL_LEDOn(LEDF);
// STM_EVAL_LEDOn(LEDG);
//
// STM_EVAL_LEDOff(LEDA);
// STM_EVAL_LEDOff(LEDB);
// STM_EVAL_LEDOff(LEDC);
// STM_EVAL_LEDOff(LEDD);
// STM_EVAL_LEDOff(LEDE);
// STM_EVAL_LEDOff(LEDF);
// STM_EVAL_LEDOff(LEDG);
// STM_EVAL_LEDOff(LEDP);
//
// STM_EVAL_SEGOff(SEG1);
// STM_EVAL_SEGOff(SEG2);
// STM_EVAL_SEGOff(SEG3);
//STM_EVAL_LEDOn(LEDP);
//GPIO_Init(ENC_DN_BUTTON_PORT, ENC_DN_BUTTON_PIN, GPIO_MODE_IN_PU_NO_IT);
//GPIO_Init(ENC_UP_BUTTON_PORT, ENC_UP_BUTTON_PIN, GPIO_MODE_IN_PU_NO_IT);
STM_EVAL_PBInit(BUTTON_KEY, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_UP, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_DOWN, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_REED, BUTTON_MODE_GPIO);
ssegInit();
ssegWriteStr("1.0.1", 5, SEG1);
enableInterrupts();
#ifdef DFS_90
HotAir_Main();
#endif
#ifdef SOLDERING_HAKKO_A1321
Soldering_Main();
#endif
while(1)
{
/*
#if 0
for (level = 0; level < calUpperLimit; level +=5)
{
Delayms(1);
}
for (level = calUpperLimit; level > 0; level -=5)
{
Delayms(1);
}
#else
RawData = GetAdcValue(ADC_SOLDER_TEMP_CHANNEL);
SmoothData = SmoothData - (LPF_Beta * (SmoothData - RawData));
level = ((int)SmoothData)*26;
#endif
*/
}
}
/**
* @brief Main program.
* @param None
* @retval None
*/
void main()
{
#ifdef FAST_I2C_MODE
/* system_clock / 1 */
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
#else
/* system_clock / 2 */
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV2);
#endif
/* Initialize LEDs mounted on STM8/128-EVAL board */
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
STM_EVAL_LEDInit(LED3);
STM_EVAL_LEDInit(LED4);
STM_EVAL_LEDOff(LED1);
STM_EVAL_LEDOff(LED2);
STM_EVAL_LEDOff(LED3);
STM_EVAL_LEDOff(LED4);
/* I2C Initialize */
I2C_Init(I2C_SPEED, 0xA0, I2C_DUTYCYCLE_2, I2C_ACK_CURR, I2C_ADDMODE_7BIT, 16);
/* Enable Buffer and Event Interrupt*/
I2C_ITConfig((I2C_IT_TypeDef)(I2C_IT_EVT | I2C_IT_BUF) , ENABLE);
enableInterrupts();
/* TXBuffer initializtion */
for (i = 0; i < BUFFERSIZE; i++)
TxBuffer[i] = i;
/* Send START condition */
I2C_GenerateSTART(ENABLE);
while (NumOfBytes);
while (I2C_GetFlagStatus(I2C_FLAG_BUSBUSY));
/* Add a delay to be sure that communication is finished */
Delay(0xFFFF);
/***** reception phase ***/
/* Wait while the bus is busy */
while (I2C_GetFlagStatus(I2C_FLAG_BUSBUSY));
/* Send START condition */
I2C_GenerateSTART(ENABLE);
/* Test on EV5 and clear it */
while (!I2C_CheckEvent(I2C_EVENT_MASTER_MODE_SELECT));
#ifdef TEN_BITS_ADDRESS
/* Send Header to Slave for write */
I2C_SendData(HEADER_ADDRESS_Write);
/* Test on EV9 and clear it*/
while (!I2C_CheckEvent(I2C_EVENT_MASTER_MODE_ADDRESS10));
/* Send slave Address */
I2C_Send7bitAddress(SLAVE_ADDRESS, I2C_DIRECTION_TX);
/* Test on EV6 and clear it */
while (!I2C_CheckEvent(I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED));
/* Repeated Start */
I2C_GenerateSTART(ENABLE);
/* Test on EV5 and clear it */
while (!I2C_CheckEvent(I2C_EVENT_MASTER_MODE_SELECT));
/* Send Header to Slave for Read */
I2C_SendData(HEADER_ADDRESS_Read);
/* Test on EV6 and clear it */
while (!I2C_CheckEvent(I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED));
#else
/* Send slave Address for write */
I2C_Send7bitAddress(SLAVE_ADDRESS, I2C_DIRECTION_RX);
/* Test on EV6 and clear it */
while (!I2C_CheckEvent(I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED));
#endif /* TEN_BITS_ADDRESS */
/* While there is data to be read */
while (NumByteToRead)
{
#ifdef SAFE_PROCEDURE
if (NumByteToRead != 3) /* Receive bytes from first byte until byte N-3 */
{
while ((I2C_GetFlagStatus(I2C_FLAG_TRANSFERFINISHED) == RESET)); /* Poll on BTF */
/* Read a byte from the Slave */
RxBuffer[Rx_Idx] = I2C_ReceiveData();
/* Point to the next location where the byte read will be saved */
Rx_Idx++;
/* Decrement the read bytes counter */
NumByteToRead--;
}
if (NumByteToRead == 3) /* it remains to read three data: data N-2, data N-1, Data N */
{
/* Data N-2 in DR and data N -1 in shift register */
while ((I2C_GetFlagStatus(I2C_FLAG_TRANSFERFINISHED) == RESET)); /* Poll on BTF */
/* Clear ACK */
I2C_AcknowledgeConfig(I2C_ACK_NONE);
/* Disable general interrupts */
disableInterrupts();
/* Read Data N-2 */
RxBuffer[Rx_Idx] = I2C_ReceiveData();
/* Point to the next location where the byte read will be saved */
Rx_Idx++;
/* Program the STOP */
I2C_GenerateSTOP(ENABLE);
/* Read DataN-1 */
RxBuffer[Rx_Idx] = I2C_ReceiveData();
/* Enable General interrupts */
enableInterrupts();
/* Point to the next location where the byte read will be saved */
Rx_Idx++;
while ((I2C_GetFlagStatus(I2C_FLAG_RXNOTEMPTY) == RESET)); /* Poll on RxNE */
/* Read DataN */
RxBuffer[Rx_Idx] = I2C_ReceiveData();
/* Reset the number of bytes to be read by master */
NumByteToRead = 0;
}
#else
if (NumByteToRead == 1)
{
/* Disable Acknowledgement */
I2C_AcknowledgeConfig(I2C_ACK_NONE);
/* Send STOP Condition */
I2C_GenerateSTOP(ENABLE);
/* Poll on RxNE Flag */
while ((I2C_GetFlagStatus(I2C_FLAG_RXNOTEMPTY) == RESET));
/* Read a byte from the Slave */
RxBuffer[Rx_Idx] = I2C_ReceiveData();
/* Point to the next location where the byte read will be saved */
Rx_Idx++;
/* Decrement the read bytes counter */
NumByteToRead--;
}
/* Test on EV7 and clear it */
if (I2C_CheckEvent(I2C_EVENT_MASTER_BYTE_RECEIVED) )
{
/* Read a byte from the EEPROM */
RxBuffer[Rx_Idx] = I2C_ReceiveData();
/* Point to the next location where the byte read will be saved */
Rx_Idx++;
/* Decrement the read bytes counter */
NumByteToRead--;
}
#endif /* SAFE_PROCEDURE */
}
/* check if sent and received data are not corrupted */
TransferStatus1 = Buffercmp((uint8_t*)TxBuffer, (uint8_t*) RxBuffer, BUFFERSIZE);
if (TransferStatus1 != FAILED)
{
while (1)
{
/* Toggle LED1*/
STM_EVAL_LEDToggle(LED1);
/* Insert delay */
Delay(0x7FFF);
}
}
else
{
while (1)
{
/* Toggle LED4*/
STM_EVAL_LEDToggle(LED4);
/* Insert delay */
Delay(0x7FFF);
}
}
}
static void CLK_Config(void){
//CLK_DeInit();
CLK_HSIPrescalerConfig(CLK_PRESCALER_CPUDIV128);
}
/**
* @brief Main program.
* @param None
* @retval None
*/
void main(void)
{
/*High speed internal clock prescaler: 1*/
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
/* UART1 configuration -------------------------------------------------------*/
/* UART1 configured as follow:
- Word Length = 8 Bits
- 1 Stop Bit
- No parity
- BaudRate = 9600 baud
- UART1 Clock enabled
- Polarity Low
- Phase Middle
- Last Bit enabled
- Receive and transmit enabled
*/
UART1_DeInit();
UART1_Init((uint32_t)9600, UART1_WORDLENGTH_8D, UART1_STOPBITS_1, UART1_PARITY_NO,
(UART1_SyncMode_TypeDef)(UART1_SYNCMODE_CLOCK_ENABLE | UART1_SYNCMODE_CPOL_LOW |UART1_SYNCMODE_CPHA_MIDDLE |UART1_SYNCMODE_LASTBIT_ENABLE),
UART1_MODE_TXRX_ENABLE);
UART1_Cmd(DISABLE);
/* SPI configuration */
SPI_DeInit();
/* Initialize SPI in Slave mode */
SPI_Init(SPI_FIRSTBIT_LSB, SPI_BAUDRATEPRESCALER_2, SPI_MODE_SLAVE, SPI_CLOCKPOLARITY_LOW,
SPI_CLOCKPHASE_1EDGE, SPI_DATADIRECTION_2LINES_FULLDUPLEX, SPI_NSS_SOFT,(uint8_t)0x07);
/* Enable the UART1*/
UART1_Cmd(ENABLE);
Delay(0xFFF);
/* Enable the SPI*/
SPI_Cmd(ENABLE);
while (NbrOfDataToRead--)
{
/* Wait until end of transmit */
while (SPI_GetFlagStatus(SPI_FLAG_TXE)== RESET)
{
}
/* Write one byte in the SPI Transmit Data Register */
SPI_SendData(TxBuffer2[TxCounter]);
/* Write one byte in the UART1 Transmit Data Register */
UART1_SendData8(TxBuffer1[TxCounter++]);
/* Wait until end of transmit */
while (UART1_GetFlagStatus(UART1_FLAG_TXE) == RESET)
{
}
/* Wait the byte is entirely received by UART1 */
while (UART1_GetFlagStatus(UART1_FLAG_RXNE) == RESET)
{
}
/* Store the received byte in the RxBuffer1 */
RxBuffer1[RxCounter] = UART1_ReceiveData8();
/* Wait the byte is entirely received by SPI */
while (SPI_GetFlagStatus(SPI_FLAG_RXNE) == RESET)
{
}
/* Store the received byte in the RxBuffer2 */
RxBuffer2[RxCounter++] = SPI_ReceiveData();
}
/* Check the received data with the sent ones */
TransferStatus1 = Buffercmp(TxBuffer1, RxBuffer2, TxBufferSize1);
/* TransferStatus = PASSED, if the data transmitted from UART1 and received by SPI are the same */
/* TransferStatus = FAILED, if the data transmitted from UART1 and received by SPI are different */
TransferStatus2 = Buffercmp(TxBuffer2, RxBuffer1, TxBufferSize2);
/* TransferStatus = PASSED, if the data transmitted from SPI and received by UART1 are the same */
/* TransferStatus = FAILED, if the data transmitted from SPI and received by UART11 are different */
while (1);
}
void clk_init(void)
{
/*High speed internal clock prescaler: 1*/
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
}
void main(void)
{
uint8_t i;
BitStatus bytes;
CLK_HSICmd(ENABLE);//开始内部高频RC
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);//不分频 16MHz
/* Initialize I/Os in Output Mode */
init_usart1(); // 输入判断
GPIO_Init(GPIOA, GPIO_PIN_3, GPIO_MODE_OUT_PP_LOW_FAST);// 输出 模式 用于Trag
GPIO_Init(GPIOA, GPIO_PIN_2, GPIO_MODE_OUT_PP_LOW_FAST);// 输出 模式 用于Trag
GPIO_WriteHigh(GPIOA, GPIO_PIN_2);
GPIO_Init(GPIOA,GPIO_PIN_1,GPIO_MODE_IN_PU_NO_IT); // 输入包含 上拉 中断
// GPIO_Init(GPIOA,GPIO_PIN_1,GPIO_MODE_IN_PU_IT);
// EXTI_SetExtIntSensitivity(EXTI_PORT_GPIOA,EXTI_SENSITIVITY_RISE_ONLY);
InitADC();
enableInterrupts();
flageExtiA=0;
sendBuff[0]=DEVICE_ID;
sendBuff[3]=0xff;
sendBuff[4]=0xff;
sendBuff[5]=0xFF;
sendBuff[6]=0xA0;
sendBuff[7]=0xFA;
while (1)
{
bytes=GPIO_ReadInputPin(GPIOA,GPIO_PIN_1);
if(bytes==RESET && flageExtiA==0)
{
flageExtiA=1;
GPIO_WriteReverse(GPIOA,GPIO_PIN_3);
for(i=0;i<8;i++)
{
Send(sendBuff[i]);
}
}else if(bytes!=RESET)
{
flageExtiA=0;
}
datas=readADCs();
sendBuff[5]=0;
sendBuff[1]=(uint8_t)(datas&0xff);
sendBuff[2]=(uint8_t)((datas>>8)&0xff);
for(i=0;i<5;i++)
{
sendBuff[5]+=sendBuff[i];
}
// datas=datas;
// bytes=GPIO_ReadInputPin(GPIOA,GPIO_PIN_1);
// if(flageExtiA!=1)
// {
// sendBuff[1]=(uint8_t)(datas&0xff);
// sendBuff[2]=(uint8_t)((datas>>8)&0xff);
// sendBuff[5]=0;
// for(i=0;i<5;i++)
// {
// sendBuff[5]+=sendBuff[i];
// }
// }
}
}
/**
* @brief Configure system clock to run at 16Mhz
* @param None
* @retval None
*/
static void CLK_Config(void)
{
/* Initialization of the clock */
/* Clock divider to HSI/1 */
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
}
void clk_config(void)
{
CLK_DeInit();
CLK_HSICmd(ENABLE);
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
}
/**
* @brief Example main entry point.
* @par Parameters:
* None
* @retval
* None
*/
void main(void)
{
u8 i = 0;
/* Initialization of the clock */
/* Clock divider to HSI/1 */
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
/* Initialization of I/Os in Output Mode */
GPIO_Init(LEDS_PORT, (LED1_PIN | LED2_PIN | LED3_PIN | LED4_PIN), GPIO_MODE_OUT_PP_LOW_FAST);
/* Initialization of I/O in Input Mode with Interrupt */
GPIO_Init(BUTTON_PORT, BUTTON_PIN, GPIO_MODE_IN_FL_IT);
/* Initialization of the Interrupt sensitivity */
EXTI_SetExtIntSensitivity(EXTI_PORT_GPIOC, EXTI_SENSITIVITY_FALL_ONLY);
/* BEEP calibration */
BEEP_LSICalibrationConfig(LSIMeasurment());
GPIO_Write(LEDS_PORT, (LED1_PIN | LED2_PIN | LED3_PIN | LED4_PIN)); /* All LEDs ON */
/* Initialize SPI for LCD */
SPI_DeInit();
SPI_Init(SPI_FIRSTBIT_MSB, SPI_BAUDRATEPRESCALER_128, SPI_MODE_MASTER, SPI_CLOCKPOLARITY_HIGH, SPI_CLOCKPHASE_2EDGE, SPI_DATADIRECTION_1LINE_TX, SPI_NSS_SOFT, 0x07);
SPI_Cmd(ENABLE);
/* Initialize LCD */
LCD_Init();
/* Clear LCD lines */
LCD_Clear();
/* Enable general interrupts for Key button reading */
enableInterrupts();
LCD_PrintString(LCD_LINE1, ENABLE, DISABLE, " BEEPER OFF");
LCD_PrintString(LCD_LINE2, ENABLE, DISABLE, " Press Key");
while (1)
{
/* Check button status */
if (ButtonPressed == TRUE) /* Button is pressed */
{
ButtonPressed = FALSE;
/* Change BEEP frequency */
switch (i)
{
case 0:
BEEP_Cmd(DISABLE);
Delay(100);
BEEP_Init(BEEP_FREQUENCY_1KHZ);
BEEP_Cmd(ENABLE);
GPIO_Write(LEDS_PORT, LED1_PIN); /* LED1 ON */
LCD_PrintString(LCD_LINE1, ENABLE, DISABLE, " BEEPER 1kHz");
i = 1;
break;
case 1:
BEEP_Cmd(DISABLE);
Delay(100);
BEEP_Init(BEEP_FREQUENCY_2KHZ);
BEEP_Cmd(ENABLE);
GPIO_Write(LEDS_PORT, LED2_PIN); /* LED2 ON */
LCD_PrintString(LCD_LINE1, ENABLE, DISABLE, " BEEPER 2kHz");
i = 2;
break;
case 2:
BEEP_Cmd(DISABLE);
Delay(100);
BEEP_Init(BEEP_FREQUENCY_4KHZ);
BEEP_Cmd(ENABLE);
GPIO_Write(LEDS_PORT, LED3_PIN); /* LED3 ON */
LCD_PrintString(LCD_LINE1, ENABLE, DISABLE, " BEEPER 4kHz");
i = 3;
break;
case 3:
BEEP_Cmd(DISABLE);
GPIO_Write(LEDS_PORT, LED4_PIN); /* LED4 ON */
LCD_PrintString(LCD_LINE1, ENABLE, DISABLE, " BEEPER OFF");
i = 0;
break;
default:
break;
}
}
}
}
/**
* @brief Main program.
* @param None
* @retval None
*/
void main(void)
{
uint32_t i = 0;
/* Configure the multiplexer on the evalboard to select the smartCard*/
Multiplexer_EvalBoard_Config();
/* Configure the GPIO ports */
GPIO_Config();
/*High speed internal clock prescaler: 1*/
CLK_HSIPrescalerConfig(CLK_PRESCALER_HSIDIV1);
/* Enable general interrupts */
enableInterrupts();
UART1_DeInit();
/* UART1 configuration -------------------------------------------------------*/
/* UART1 configured as follow:
- Word Length = 9 Bits
- 1.5 Stop Bit
- Even parity
- BaudRate = 10752 baud
- Receive and transmit enabled
- UART1 Clock enabled
*/
UART1_Init((uint32_t)10752, UART1_WORDLENGTH_9D, UART1_STOPBITS_1_5, UART1_PARITY_EVEN,
UART1_SYNCMODE_CLOCK_ENABLE, UART1_MODE_TXRX_ENABLE);
/* UART1 Clock set to 4MHz (frequence master 16 MHZ / 4) */
UART1_SetPrescaler(0x02);
/* UART1 Guard Time set to Bit */
UART1_SetGuardTime(0x2);
/* Enable the UART1 Parity Error Interrupt */
UART1_ITConfig(UART1_IT_PE, ENABLE);
/* Enable the NACK Transmission */
UART1_SmartCardNACKCmd(ENABLE);
/* Enable the Smart Card Interface */
UART1_SmartCardCmd(ENABLE);
/* Loop while no smart card is detected */
while ((GPIO_ReadInputData(GPIOE)& 0x01) == 0x00)
{
}
/* PG7 - SmartCard_/CMDVCC: low */
GPIO_WriteLow(GPIOG, GPIO_PIN_7);
/* release SmartCard_RESET signal */
GPIO_WriteLow(GPIOG, GPIO_PIN_5);
for (i = 0; i < 6000; i++)
{
}
/* set SmartCard_RESET signal */
GPIO_WriteHigh(GPIOG, GPIO_PIN_5);
/* Read Smart Card ATR response */
for (index = 0; index < 40; index++)
{
Counter = 0;
while ((UART1_GetFlagStatus(UART1_FLAG_RXNE) == RESET) && (Counter != SC_Receive_Timeout))
{
Counter++;
}
if (Counter != SC_Receive_Timeout)
{
DST_Buffer[index] = UART1_ReceiveData8();
}
}
/* Decode ATR */
CardProtocol = SC_decode_Answer2reset(DST_Buffer);
/* Test if the inserted card is ISO7816-3 T=0 compatible */
if (CardProtocol == 0)
{
/* Inserted card is ISO7816-3 T=0 compatible */
ATRDecodeStatus = PASSED;
}
else
{
/* Inserted smart card is not ISO7816-3 T=0 compatible */
ATRDecodeStatus = FAILED;
}
while (1)
{}
}
