void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Unlock protected registers */
SYS_UnlockReg();
/* Enable External XTAL (4~24 MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
/* Waiting for 12MHz clock ready */
CLK_WaitClockReady( CLK_STATUS_HXTSTB_Msk);
/* Switch HCLK clock source to HXT */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HXT,CLK_CLKDIV0_HCLK(1));
/* Set PLL to power down mode and PLL_STB bit in CLKSTATUS register will be cleared by hardware.*/
CLK->PLLCTL |= CLK_PLLCTL_PD_Msk;
/* Set PLL frequency */
CLK->PLLCTL = CLK_PLLCTL_84MHz_HXT;
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_STATUS_PLLSTB_Msk);
/* Switch HCLK clock source to PLL */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_PLL,CLK_CLKDIV0_HCLK(1));
/* Enable IP clock */
CLK_EnableModuleClock(UART0_MODULE);
CLK_EnableModuleClock(TMR0_MODULE);
CLK_EnableModuleClock(SPI0_MODULE);
CLK_EnableModuleClock(SPI1_MODULE);
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));
CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR0SEL_HXT, 0);
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate SystemCoreClock. */
SystemCoreClockUpdate();
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set GPG multi-function pins for UART0 RXD and TXD */
SYS->GPG_MFPL = SYS_GPG_MFPL_PG1MFP_UART0_RXD | SYS_GPG_MFPL_PG2MFP_UART0_TXD ;
/* SPI0: GPE4=SS0, GPE3=MOSI0, GPE2=MISO0, GPE5=CLK */
SYS->GPE_MFPL = (SYS_GPE_MFPL_PE2MFP_SPI0_MISO0 | SYS_GPE_MFPL_PE3MFP_SPI0_MOSI0 | SYS_GPE_MFPL_PE4MFP_SPI0_SS0 | SYS_GPE_MFPL_PE5MFP_SPI0_CLK);
/* SPI1: GPC12=SS0, GPC15=MOSI0, GPD0=MISO0, GPD1=CLK */
SYS->GPC_MFPH |= (SYS_GPC_MFPH_PC12MFP_SPI1_SS0 | SYS_GPC_MFPH_PC15MFP_SPI1_MOSI0);
SYS->GPD_MFPL = (SYS_GPD_MFPL_PD0MFP_SPI1_MISO0 | SYS_GPD_MFPL_PD1MFP_SPI1_CLK);
/* Lock protected registers */
SYS_LockReg();
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Enable Internal RC clock */
CLK_EnableXtalRC(CLK_PWRCON_OSC22M_EN_Msk);
/* Waiting for IRC22M clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_OSC22M_STB_Msk);
/* Switch HCLK clock source to Internal RC and HCLK source divide 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HIRC, CLK_CLKDIV_HCLK(1));
/* Enable external 12MHz XTAL, internal 22.1184MHz */
CLK_EnableXtalRC(CLK_PWRCON_XTL12M_EN_Msk | CLK_PWRCON_OSC22M_EN_Msk);
/* Enable PLL and Set PLL frequency */
CLK_SetCoreClock(PLLCON_SETTING);
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_PLL_STB_Msk | CLK_CLKSTATUS_XTL12M_STB_Msk | CLK_CLKSTATUS_OSC22M_STB_Msk);
/* Switch HCLK clock source to PLL, STCLK to HCLK/2 */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_PLL, CLK_CLKDIV_HCLK(2));
/* Enable UART module clock */
CLK_EnableModuleClock(UART0_MODULE);
/* Enable PWM module clock */
CLK_EnableModuleClock(PWM01_MODULE);
CLK_EnableModuleClock(PWM23_MODULE);
/* Select UART module clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_CLKDIV_UART(1));
/* Select PWM module clock source */
CLK_SetModuleClock(PWM01_MODULE, CLK_CLKSEL1_PWM01_S_HXT, 0);
CLK_SetModuleClock(PWM23_MODULE, CLK_CLKSEL1_PWM23_S_HXT, 0);
/* Reset PWMA channel0~channel3 */
SYS_ResetModule(PWM03_RST);
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate PllClock, SystemCoreClock and CycylesPerUs automatically. */
//SystemCoreClockUpdate();
PllClock = PLL_CLOCK; // PLL
SystemCoreClock = PLL_CLOCK / 1; // HCLK
CyclesPerUs = PLL_CLOCK / 1000000; // For SYS_SysTickDelay()
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set P3 multi-function pins for UART0 RXD and TXD */
SYS->P3_MFP = SYS_MFP_P30_RXD0 | SYS_MFP_P31_TXD0;
/* Set P2 multi-function pins for PWMA Channel0~3 */
SYS->P2_MFP = SYS_MFP_P20_PWM0 | SYS_MFP_P21_PWM1 | SYS_MFP_P22_PWM2 | SYS_MFP_P23_PWM3;
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Unlock protected registers */
SYS_UnlockReg();
/* Enable External XTAL (4~24 MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
/* Enable LIRC */
CLK_EnableXtalRC(CLK_PWRCTL_LIRCEN_Msk);
/* Waiting for 12MHz clock ready */
CLK_WaitClockReady( CLK_STATUS_HXTSTB_Msk);
/* Waiting for LIRC clock stable */
CLK_WaitClockReady( CLK_STATUS_LIRCSTB_Msk);
/* Switch HCLK clock source to HXT */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HXT,CLK_CLKDIV0_HCLK(1));
/* Set PLL to power down mode and PLL_STB bit in CLKSTATUS register will be cleared by hardware.*/
CLK->PLLCTL |= CLK_PLLCTL_PD_Msk;
/* Set PLL frequency */
CLK->PLLCTL = CLK_PLLCTL_84MHz_HXT;
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_STATUS_PLLSTB_Msk);
/* Switch HCLK clock source to PLL */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_PLL,CLK_CLKDIV0_HCLK(1));
/* Enable IP clock */
CLK_EnableModuleClock(UART0_MODULE);
CLK_EnableModuleClock(WDT_MODULE);
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));
CLK_SetModuleClock(WDT_MODULE, CLK_CLKSEL1_WDTSEL_LIRC, 0);
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate SystemCoreClock. */
SystemCoreClockUpdate();
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set GPG multi-function pins for UART0 RXD and TXD */
SYS->GPG_MFPL = SYS_GPG_MFPL_PG1MFP_UART0_RXD | SYS_GPG_MFPL_PG2MFP_UART0_TXD ;
/* Lock protected registers */
SYS_LockReg();
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Unlock protected registers */
SYS_UnlockReg();
/* Enable External XTAL (4~24 MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
/* Waiting for 12MHz clock ready */
CLK_WaitClockReady( CLK_STATUS_HXTSTB_Msk);
/* Switch HCLK clock source to HXT */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HXT,CLK_CLKDIV0_HCLK(1));
/* Set PLL to power down mode and PLL_STB bit in CLKSTATUS register will be cleared by hardware.*/
CLK->PLLCTL |= CLK_PLLCTL_PD_Msk;
/* Set PLL frequency */
CLK->PLLCTL = CLK_PLLCTL_84MHz_HXT;
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_STATUS_PLLSTB_Msk);
/* Switch HCLK clock source to PLL */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_PLL,CLK_CLKDIV0_HCLK(1));
/* Enable IP clock */
CLK_EnableModuleClock(UART0_MODULE);
CLK_EnableModuleClock(TMR0_MODULE);
CLK_EnableModuleClock(SPI2_MODULE);
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));
CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR0SEL_HXT, 0);
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate SystemCoreClock. */
SystemCoreClockUpdate();
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set GPG multi-function pins for UART0 RXD and TXD */
SYS->GPG_MFPL = SYS_GPG_MFPL_PG1MFP_UART0_RXD | SYS_GPG_MFPL_PG2MFP_UART0_TXD ;
/* SPI2: SS0=GPH_5, MOSI0=GPH_8, MISO0=GPH_7, CLK=GPH_6, MISO1=GPH_9, MOSI11=GPH10 */
SYS->GPH_MFPL = (SYS_GPH_MFPL_PH5MFP_SPI2_SS0 | SYS_GPH_MFPL_PH6MFP_SPI2_CLK | SYS_GPH_MFPL_PH7MFP_SPI2_MISO0);
SYS->GPH_MFPH = (SYS_GPH_MFPH_PH8MFP_SPI2_MOSI0 | SYS_GPH_MFPH_PH9MFP_SPI2_MISO1 | SYS_GPH_MFPH_PH10MFP_SPI2_MOSI1);
/* Lock protected registers */
SYS_LockReg();
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Unlock protected registers */
SYS_UnlockReg();
/* Enable External XTAL (4~24 MHz) */
CLK_EnableXtalRC(CLK_PWRCON_HXT_EN_Msk);
/* Waiting for 12MHz clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_HXT_STB_Msk);
/* Switch HCLK clock source to HXT */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_CLKDIV0_HCLK(1));
/* Set PLL to power down mode and PLL_STB bit in CLKSTATUS register will be cleared by hardware.*/
CLK->PLLCON |= CLK_PLLCON_PD_Msk;
/* Set PLL frequency */
CLK->PLLCON = PLLCON_SETTING;
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_PLL_STB_Msk);
/* Switch HCLK clock source to PLL */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_PLL,CLK_CLKDIV0_HCLK(1));
/* Enable IP clock */
CLK_EnableModuleClock(UART0_MODULE);
CLK_EnableModuleClock(PDMA_MODULE);
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE,CLK_CLKSEL1_UART_S_HXT,CLK_CLKDIV0_UART(1));
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate SystemCoreClock. */
SystemCoreClockUpdate();
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set GPG multi-function pins for UART0 RXD and TXD */
SYS->GPG_MFPL &= ~(SYS_GPG_MFPL_PG1_MFP_Msk|SYS_GPG_MFPL_PG2_MFP_Msk);
SYS->GPG_MFPL |= SYS_GPG_MFPL_PG1_MFP_UART0_RXD | SYS_GPG_MFPL_PG2_MFP_UART0_TXD ;
/* Set GPG multi-function pins for CKO */
SYS->GPC_MFPL = (SYS->GPC_MFPL & ~SYS_GPC_MFPL_PC5_MFP_Msk) | SYS_GPC_MFPL_PC5_MFP_CLK_O ;
/* Lock protected registers */
SYS_LockReg();
}
/*---------------------------------------------------------------------------------------------------------*/
void SYS_Init(void)
{
/* Unlock protected registers */
SYS_UnlockReg();
/* Set HCLK source form HXT and HCLK source divide 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_HCLK_CLK_DIVIDER(1));
/* Enable external 12MHz HXT, 32KHz LXT and HIRC */
CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk | CLK_PWRCTL_LXT_EN_Msk | CLK_PWRCTL_HIRC_EN_Msk);
/* Set HCLK frequency 12MHz */
CLK_SetCoreClock(12000000);
/* Enable IP clock */
CLK_EnableModuleClock(UART0_MODULE);
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE,CLK_CLKSEL1_UART_S_HIRC,CLK_UART_CLK_DIVIDER(1));
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set PA multi-function pins for UART0 RXD and TXD */
SYS->PA_H_MFP &= ~( SYS_PA_H_MFP_PA15_MFP_Msk | SYS_PA_H_MFP_PA14_MFP_Msk);
SYS->PA_H_MFP |= (SYS_PA_H_MFP_PA15_MFP_UART0_TX|SYS_PA_H_MFP_PA14_MFP_UART0_RX);
/* Set PB multi-function pins for Clock Output */
SYS->PB_H_MFP = ( SYS->PB_H_MFP & ~SYS_PB_H_MFP_PB12_MFP_Msk ) | SYS_PB_H_MFP_PB12_MFP_CKO;
/* Lock protected registers */
SYS_LockReg();
}
/*--------------------------------------------------------------------------*/
void SYS_Init(void)
{
/* Unlock protected registers */
SYS_UnlockReg();
/* Enable external 12MHz HXT */
CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk);
CLK_EnablePLL(CLK_PLLCTL_PLL_SRC_HXT, 96000000);
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_HXT_STB_Msk | CLK_CLKSTATUS_PLL_STB_Msk);
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_PLL, CLK_HCLK_CLK_DIVIDER(3));
/* Select IP clock source */
CLK_SetModuleClock(USBD_MODULE, 0, CLK_USB_CLK_DIVIDER(2));
/* Enable IP clock */
CLK_EnableModuleClock(USBD_MODULE);
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_UART_CLK_DIVIDER(1));
/* Enable IP clock */
CLK_EnableModuleClock(UART0_MODULE);
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set PA multi-function pins for UART0 RXD and TXD */
SYS->PA_H_MFP &= ~( SYS_PA_H_MFP_PA15_MFP_Msk | SYS_PA_H_MFP_PA14_MFP_Msk);
SYS->PA_H_MFP |= (SYS_PA_H_MFP_PA15_MFP_UART0_TX|SYS_PA_H_MFP_PA14_MFP_UART0_RX);
/* Lock protected registers */
SYS_LockReg();
}
/**
* This function will initial Clock tree.
*/
static void clock_init(void)
{
/* Unlock protected registers */
SYS_UnlockReg();
SystemInit();
/* Set XT1_OUT(PF.2) and XT1_IN(PF.3) to input mode */
PF->MODE &= ~(GPIO_MODE_MODE2_Msk | GPIO_MODE_MODE3_Msk);
/* Enable External XTAL (4~24 MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
/* Waiting for 12MHz clock ready */
CLK_WaitClockReady( CLK_STATUS_HXTSTB_Msk);
/* Switch HCLK clock source to HXT */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HXT,CLK_CLKDIV0_HCLK(1));
/* Set core clock as PLL_CLOCK from PLL */
CLK_SetCoreClock(FREQ_192MHZ);
/* Set both PCLK0 and PCLK1 as HCLK/4 */
CLK->PCLKDIV = CLK_PCLKDIV_PCLK0DIV4 | CLK_PCLKDIV_PCLK1DIV4;
SystemCoreClockUpdate();
/* Lock protected registers */
SYS_LockReg();
}
void setupSystemClock()
{
SYS_UnlockReg();
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Enable HIRC clock */
CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);
/* Waiting for HIRC clock ready */
CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);
/* Switch HCLK clock source to HIRC */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV0_HCLK(1));
/* Enable external XTAL 12MHz clock */
//CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
/* Waiting for external XTAL clock ready */
//CLK_WaitClockReady(CLK_STATUS_HXTSTB_Msk);
/* Set core clock as PLL_CLOCK from PLL and SysTick source to HCLK/2*/
CLK_SetCoreClock(SYSTEM_CLOCK);
CLK_SetSysTickClockSrc(CLK_CLKSEL0_STCLKSEL_HCLK_DIV2);
/* Waiting for PLL clock ready */
CLK_WaitClockReady(CLK_STATUS_PLLSTB_Msk);
SYS_LockReg();
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Unlock protected registers */
SYS_UnlockReg();
/* Set HCLK source form HXT and HCLK source divide 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HXT, CLK_CLKDIV0_HCLK(1));
/* Set HCLK frequency 42MHz */
CLK_SetCoreClock(42000000);
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_HIRC, CLK_CLKDIV0_UART(1));
/* Enable IP clock */
CLK_EnableModuleClock(UART0_MODULE);
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate PllClock, SystemCoreClock and CycylesPerUs automatically. */
SystemCoreClockUpdate();
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set PD multi-function pins for UART0 RXD(PD.0) and TXD(PD.1) */
SYS->GPD_MFPL &= ~(SYS_GPD_MFPL_PD0MFP_Msk | SYS_GPD_MFPL_PD1MFP_Msk);
SYS->GPD_MFPL |= (SYS_GPD_MFPL_PD0MFP_UART0_RXD | SYS_GPD_MFPL_PD1MFP_UART0_TXD);
/* Lock protected registers */
SYS_LockReg();
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Enable Internal RC 22.1184MHz clock */
CLK_EnableXtalRC(CLK_PWRCON_OSC22M_EN_Msk);
/* Waiting for Internal RC clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_OSC22M_STB_Msk);
/* Switch HCLK clock source to Internal RC and HCLK source divide 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HIRC, CLK_CLKDIV_HCLK(1));
/* Enable external XTAL 12MHz clock */
CLK_EnableXtalRC(CLK_PWRCON_XTL12M_EN_Msk);
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_XTL12M_STB_Msk);
/* Set core clock as PLL_CLOCK from PLL */
CLK_SetCoreClock(PLL_CLOCK);
/* Enable UART module clock */
CLK_EnableModuleClock(UART0_MODULE);
/* Select UART module clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_CLKDIV_UART(1));
/* Enable Timer 0~3 module clock */
CLK_EnableModuleClock(TMR0_MODULE);
CLK_EnableModuleClock(TMR2_MODULE);
CLK_EnableModuleClock(TMR3_MODULE);
/* Select Timer 0~3 module clock source */
CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR0_S_HXT, NULL);
CLK_SetModuleClock(TMR2_MODULE, CLK_CLKSEL1_TMR2_S_HCLK, NULL);
CLK_SetModuleClock(TMR3_MODULE, CLK_CLKSEL1_TMR3_S_HXT, NULL);
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set PB multi-function pins for UART0 RXD, TXD */
SYS->GPB_MFP &= ~(SYS_GPB_MFP_PB0_Msk | SYS_GPB_MFP_PB1_Msk);
SYS->GPB_MFP |= (SYS_GPB_MFP_PB0_UART0_RXD | SYS_GPB_MFP_PB1_UART0_TXD);
/* Set PB multi-function pins for TM0, TM2, TM3 and TM2_EXT */
SYS->GPB_MFP &= ~(SYS_GPB_MFP_PB8_Msk | SYS_GPB_MFP_PB10_Msk |
SYS_GPB_MFP_PB11_Msk | SYS_GPB_MFP_PB2_Msk);
SYS->GPB_MFP |= (SYS_GPB_MFP_PB8_TM0 | SYS_GPB_MFP_PB10_TM2 |
SYS_GPB_MFP_PB11_TM3 | SYS_GPB_MFP_PB2_TM2_EXT);
SYS->ALT_MFP &= ~( SYS_ALT_MFP_PB8_Msk | SYS_ALT_MFP_PB10_Msk | SYS_ALT_MFP_PB11_Msk |
SYS_ALT_MFP_PB2_Msk);
SYS->ALT_MFP |= (SYS_ALT_MFP_PB8_TM0 | SYS_ALT_MFP_PB10_TM2 |SYS_ALT_MFP_PB11_TM3 |
SYS_ALT_MFP_PB2_TM2_EXT);
SYS->ALT_MFP2 &= ~SYS_ALT_MFP2_PB2_TM2_Msk;
SYS->ALT_MFP2 |= SYS_ALT_MFP2_PB2_TM2_EXT;
}
/**
* Initializes the system.
* System control registers must be unlocked.
*/
void SYS_Init() {
// TODO: why is SYS_UnlockReg() needed? Should be already unlocked.
SYS_UnlockReg();
// HIRC clock (internal RC 22.1184MHz)
CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);
CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);
// HCLK clock source: HIRC, HCLK source divider: 1
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV0_HCLK(1));
// HXT clock (external XTAL 12MHz)
CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
CLK_WaitClockReady(CLK_STATUS_HXTSTB_Msk);
// Enable 72MHz optimization
FMC_EnableFreqOptimizeMode(FMC_FTCTL_OPTIMIZE_72MHZ);
// Core clock: PLL
CLK_SetCoreClock(PLL_CLOCK);
CLK_WaitClockReady(CLK_STATUS_PLLSTB_Msk);
// SPI0 clock: PCLK0
CLK_SetModuleClock(SPI0_MODULE, CLK_CLKSEL2_SPI0SEL_PCLK0, 0);
CLK_EnableModuleClock(SPI0_MODULE);
// TMR0 clock: HXT
CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR0SEL_HXT, 0);
CLK_EnableModuleClock(TMR0_MODULE);
// USBD clock
CLK_SetModuleClock(USBD_MODULE, 0, CLK_CLKDIV0_USB(3));
CLK_EnableModuleClock(USBD_MODULE);
// Enable USB 3.3V LDO
SYS->USBPHY = SYS_USBPHY_LDO33EN_Msk;
// EADC clock: 72Mhz / 8
CLK_SetModuleClock(EADC_MODULE, 0, CLK_CLKDIV0_EADC(8));
CLK_EnableModuleClock(EADC_MODULE);
// Enable BOD (reset, 2.2V)
SYS_EnableBOD(SYS_BODCTL_BOD_RST_EN, SYS_BODCTL_BODVL_2_2V);
// Update system core clock
SystemCoreClockUpdate();
// Initialize dataflash
Dataflash_Init();
// Initialize I/O
Display_SetupSPI();
Button_Init();
ADC_Init();
// Initialize display
Display_Init();
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Enable HIRC clock (Internal RC 22.1184MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);
/* Wait for HIRC clock ready */
CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);
/* Select HCLK clock source as HIRC and and HCLK source divider as 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV0_HCLK(1));
/* Set PLL to Power-down mode and PLLSTB bit in CLK_STATUS register will be cleared by hardware.*/
CLK_DisablePLL();
/* Enable HXT clock (external XTAL 12MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
/* Wait for HXT clock ready */
CLK_WaitClockReady(CLK_STATUS_HXTSTB_Msk);
/* Set core clock as PLL_CLOCK from PLL */
CLK_SetCoreClock(PLL_CLOCK);
/* Enable UART module clock */
CLK_EnableModuleClock(UART0_MODULE);
/* Select UART module clock source as HXT and UART module clock divider as 1 */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));
/* Enable EADC module clock */
CLK_EnableModuleClock(EADC_MODULE);
/* EADC clock source is 72MHz, set divider to 8, ADC clock is 72/8 MHz */
CLK_SetModuleClock(EADC_MODULE, 0, CLK_CLKDIV0_EADC(8));
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set PD multi-function pins for UART0 RXD and TXD */
SYS->GPD_MFPL &= ~(SYS_GPD_MFPL_PD0MFP_Msk | SYS_GPD_MFPL_PD1MFP_Msk);
SYS->GPD_MFPL |= (SYS_GPD_MFPL_PD0MFP_UART0_RXD | SYS_GPD_MFPL_PD1MFP_UART0_TXD);
/* Configure the GPB0 - GPB3 ADC analog input pins. */
SYS->GPB_MFPL &= ~(SYS_GPB_MFPL_PB0MFP_Msk | SYS_GPB_MFPL_PB1MFP_Msk |
SYS_GPB_MFPL_PB2MFP_Msk | SYS_GPB_MFPL_PB3MFP_Msk);
SYS->GPB_MFPL |= (SYS_GPB_MFPL_PB0MFP_EADC_CH0 | SYS_GPB_MFPL_PB1MFP_EADC_CH1 |
SYS_GPB_MFPL_PB2MFP_EADC_CH2 | SYS_GPB_MFPL_PB3MFP_EADC_CH3);
/* Disable the GPB0 - GPB3 digital input path to avoid the leakage current. */
GPIO_DISABLE_DIGITAL_PATH(PB, 0xF);
}
/*--------------------------------------------------------------------------*/
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Enable Internal RC 22.1184 MHz clock */
CLK_EnableXtalRC(CLK_PWRCON_OSC22M_EN_Msk);
/* Waiting for Internal RC clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_OSC22M_STB_Msk);
/* Switch HCLK clock source to Internal RC and HCLK source divide 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HIRC, CLK_CLKDIV_HCLK(1));
#if (!CRYSTAL_LESS)
/* Enable external XTAL 12 MHz clock */
CLK_EnableXtalRC(CLK_PWRCON_XTL12M_EN_Msk);
/* Waiting for external XTAL clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_XTL12M_STB_Msk);
/* Set core clock */
CLK_SetCoreClock(72000000);
/* Select module clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HIRC, CLK_CLKDIV_UART(1));
CLK_SetModuleClock(USBD_MODULE, CLK_CLKSEL0_USB_S_PLL, CLK_CLKDIV_USB(3));
#else
/* Enable Internal RC 48MHz clock */
CLK_EnableXtalRC(CLK_PWRCON_OSC48M_EN_Msk);
/* Waiting for Internal RC clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_OSC48M_STB_Msk);
/* Select module clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HIRC, CLK_CLKDIV_UART(1));
CLK_SetModuleClock(USBD_MODULE, CLK_CLKSEL0_USB_S_RC48M, CLK_CLKDIV_USB(1));
#endif
/* Enable module clock */
CLK_EnableModuleClock(UART0_MODULE);
CLK_EnableModuleClock(USBD_MODULE);
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set GPB multi-function pins for UART0 RXD and TXD, and Clock Output */
SYS->GPB_MFP &= ~(SYS_GPB_MFP_PB0_Msk | SYS_GPB_MFP_PB1_Msk | SYS_GPB_MFP_PB8_Msk);
SYS->ALT_MFP &= ~SYS_ALT_MFP_PB8_Msk;
SYS->GPB_MFP |= (SYS_GPB_MFP_PB0_UART0_RXD | SYS_GPB_MFP_PB1_UART0_TXD | SYS_GPB_MFP_PB8_CLKO);
SYS->ALT_MFP |= SYS_ALT_MFP_PB8_CLKO;
/* Enable CLKO (PB.8) for monitor HCLK. CLKO = HCLK/8 Hz*/
EnableCLKO((2 << CLK_CLKSEL2_FRQDIV_S_Pos), 2);
}
/*---------------------------------------------------------------------------------------------------------*/
void SysInit(void)
{
/* Unlock protected registers */
SYS_UnlockReg();
/* Set HCLK source form HXT and HCLK source divide 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_HCLK_CLK_DIVIDER(1));
/* Enable external 12MHz HXT, 32KHz LXT and HIRC */
CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk | CLK_PWRCTL_LXT_EN_Msk | CLK_PWRCTL_HIRC_EN_Msk);
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_HXT_STB_Msk | CLK_CLKSTATUS_LXT_STB_Msk | CLK_CLKSTATUS_HIRC_STB_Msk);
#if 1
SYS->PB_H_MFP &= ~( SYS_PB_H_MFP_PB14_MFP_Msk | SYS_PB_H_MFP_PB13_MFP_Msk);
SYS->PB_H_MFP |= (SYS_PB_H_MFP_PB14_MFP_UART0_TX | SYS_PB_H_MFP_PB13_MFP_UART0_RX );
UART0->BAUD = 0x67; /* Baud Rate:115200 OSC:12MHz */
//UART0->BAUD = 0x60; /* Baud Rate:115200 OSC:11.0592 MHz */
UART0->TLCTL = (UART0->TLCTL & ~0x3) | 0x3; /* character len is 8 bits */
UART0->TLCTL |= (1<<2);
#endif
/* Set HCLK frequency 32MHz */
CLK_SetCoreClock(32000000);
/* Enable IP clock */
CLK_EnableModuleClock(UART0_MODULE);
/* Enable PWM clock */
CLK_EnableModuleClock(PWM0_CH01_MODULE);
CLK_EnableModuleClock(PWM0_CH23_MODULE);
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE,CLK_CLKSEL1_UART_S_HIRC,CLK_UART_CLK_DIVIDER(1));
/* Set HCLK as PWM clock source */
CLK_SetModuleClock(PWM0_CH01_MODULE, CLK_CLKSEL1_PWM0_CH01_S_HCLK, 0);
CLK_SetModuleClock(PWM0_CH23_MODULE, CLK_CLKSEL1_PWM0_CH23_S_HCLK, 0);
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set PA multi-function pins for UART0 RXD and TXD */
SYS->PB_L_MFP &= ~( SYS_PB_L_MFP_PB0_MFP_Msk | SYS_PB_L_MFP_PB1_MFP_Msk);
SYS->PB_L_MFP |= (SYS_PB_L_MFP_PB0_MFP_UART0_TX | SYS_PB_L_MFP_PB1_MFP_UART0_RX );
/* Set PB multi-function pins for Clock Output */
SYS->PB_H_MFP = ( SYS->PB_H_MFP & ~SYS_PB_H_MFP_PB12_MFP_Msk ) | SYS_PB_H_MFP_PB12_MFP_CKO0;
/* Set PB and PE multi-function pins for PWM */
SYS->PB_H_MFP = (SYS->PB_H_MFP & ~(SYS_PB_H_MFP_PB8_MFP_Msk | SYS_PB_H_MFP_PB9_MFP_Msk)) | SYS_PB_H_MFP_PB8_MFP_PWM0_CH0 | SYS_PB_H_MFP_PB9_MFP_PWM0_CH1;
SYS->PE_H_MFP = (SYS->PE_H_MFP & ~(SYS_PE_H_MFP_PE8_MFP_Msk | SYS_PE_H_MFP_PE9_MFP_Msk)) | SYS_PE_H_MFP_PE8_MFP_PWM0_CH2 | SYS_PE_H_MFP_PE9_MFP_PWM0_CH3;
/* Lock protected registers */
SYS_LockReg();
}
void SYS_PLL_Test(void)
{
int32_t i;
/*---------------------------------------------------------------------------------------------------------*/
/* PLL clock configuration test */
/*---------------------------------------------------------------------------------------------------------*/
printf("\n-------------------------[ Test PLL ]-----------------------------\n");
for(i = 0; i < sizeof(g_au32PllSetting) / sizeof(g_au32PllSetting[0]) ; i++) {
/* Switch HCLK clock source to HXT and HCLK source divide 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT, CLK_CLKDIV_HCLK(1));
/* Set PLL to power down mode and PLL_STB bit in CLKSTATUS register will be cleared by hardware. */
CLK_DisablePLL();
/* Set PLL frequency */
CLK->PLLCON = g_au32PllSetting[i];
/* Waiting for PLL clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_PLL_STB_Msk);
/* Switch HCLK clock source to PLL */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_PLL, CLK_CLKDIV_HCLK(1));
printf(" Change system clock to %d Hz ...................... ", SystemCoreClock);
/* Output selected clock to CKO, CKO Clock = HCLK / 2^(1 + 1) */
CLK_EnableCKO(CLK_CLKSEL2_FRQDIV_S_HCLK, 1, 0);
/* The delay loop is used to check if the CPU speed is increasing */
Delay(0x400000);
if(pi()) {
printf("[FAIL]\n");
} else {
printf("[OK]\n");
}
/* Disable CKO clock */
CLK_DisableCKO();
}
}
/*---------------------------------------------------------------------------------------------------------*/
void SysInit(void)
{
/* Unlock protected registers */
SYS_UnlockReg();
/* Set HCLK source form HXT and HCLK source divide 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_HCLK_CLK_DIVIDER(1));
/* Enable external 12MHz HXT, 32KHz LXT and HIRC */
CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk | CLK_PWRCTL_LXT_EN_Msk | CLK_PWRCTL_HIRC_EN_Msk);
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_HXT_STB_Msk | CLK_CLKSTATUS_LXT_STB_Msk | CLK_CLKSTATUS_HIRC_STB_Msk);
#if 1
SYS->PB_H_MFP &= ~( SYS_PB_H_MFP_PB14_MFP_Msk | SYS_PB_H_MFP_PB13_MFP_Msk);
SYS->PB_H_MFP |= (SYS_PB_H_MFP_PB14_MFP_UART0_TX | SYS_PB_H_MFP_PB13_MFP_UART0_RX );
UART0->BAUD = 0x67; /* Baud Rate:115200 OSC:12MHz */
//UART0->BAUD = 0x60; /* Baud Rate:115200 OSC:11.0592 MHz */
UART0->TLCTL = (UART0->TLCTL & ~0x3) | 0x3; /* character len is 8 bits */
UART0->TLCTL |= (1<<2);
#endif
/* Set HCLK frequency 32MHz */
CLK_SetCoreClock(32000000);
/* Enable IP clock */
CLK_EnableModuleClock(UART0_MODULE);
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE,CLK_CLKSEL1_UART_S_HIRC,CLK_UART_CLK_DIVIDER(1));
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set PA multi-function pins for UART0 RXD and TXD */
SYS->PB_L_MFP &= ~( SYS_PB_L_MFP_PB0_MFP_Msk | SYS_PB_L_MFP_PB1_MFP_Msk);
SYS->PB_L_MFP |= (SYS_PB_L_MFP_PB0_MFP_UART0_TX | SYS_PB_L_MFP_PB1_MFP_UART0_RX );
/* Set PB multi-function pins for Clock Output */
SYS->PB_H_MFP = ( SYS->PB_H_MFP & ~SYS_PB_H_MFP_PB12_MFP_Msk ) | SYS_PB_H_MFP_PB12_MFP_CKO0;
/* Set PA multi-function pins for ADC */
SYS->PA_L_MFP &= ~(SYS_PA_L_MFP_PA0_MFP_Msk | SYS_PA_L_MFP_PA1_MFP_Msk | SYS_PA_L_MFP_PA2_MFP_Msk);
SYS->PA_L_MFP |= SYS_PA_L_MFP_PA0_MFP_ADC_CH0 | SYS_PA_L_MFP_PA1_MFP_ADC_CH1 | SYS_PA_L_MFP_PA2_MFP_ADC_CH2;
/* Disable digital input path */
PA->OFFD = PA->OFFD | ((ADC_CH_0_MASK | ADC_CH_1_MASK | ADC_CH_2_MASK)<< 16);
/* Enable ADC clock */
CLK_EnableModuleClock(ADC_MODULE);
/* Lock protected registers */
SYS_LockReg();
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Enable Internal RC 22.1184 MHz clock */
CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);
/* Waiting for Internal RC clock ready */
CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);
/* Switch HCLK clock source to Internal RC and set HCLK divider to 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV0_HCLK(1));
/* Enable external XTAL 12 MHz clock */
CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
/* Waiting for external XTAL clock ready */
CLK_WaitClockReady(CLK_STATUS_HXTSTB_Msk);
/* Set Flash Access Delay */
FMC->FTCTL |= FMC_FTCTL_FOM_Msk;
/* Set core clock */
CLK_SetCoreClock(72000000);
/* Enable module clock */
CLK_EnableModuleClock(UART0_MODULE);
CLK_EnableModuleClock(UART1_MODULE);
CLK_EnableModuleClock(USBD_MODULE);
/* Select module clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));
CLK_SetModuleClock(UART1_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));
CLK_SetModuleClock(USBD_MODULE, 0, CLK_CLKDIV0_USB(3));
/* Enable USB LDO33 */
SYS->USBPHY = SYS_USBPHY_LDO33EN_Msk;
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set GPD multi-function pins for UART0 RXD, TXD and Clock Output */
SYS->GPD_MFPL = SYS_GPD_MFPL_PD0MFP_UART0_RXD | SYS_GPD_MFPL_PD1MFP_UART0_TXD | SYS_GPD_MFPL_PD6MFP_CLKO;
/* Set GPA multi-function pins for UART1 RXD and TXD */
SYS->GPA_MFPL = SYS_GPA_MFPL_PA0MFP_UART1_TXD | SYS_GPA_MFPL_PA1MFP_UART1_RXD;
/* Enable CLKO (PD.6) for monitor HCLK. CLKO = HCLK/8 Hz */
CLK_EnableCKO(CLK_CLKSEL1_CLKOSEL_HCLK, 2, 0);
}
/**
* @brief This function set HCLK frequency. The frequency unit is Hz. The range of u32Hclk is 16 ~ 32 MHz
* @param u32Hclk is HCLK frequency
* @return None
*/
uint32_t CLK_SetCoreClock(uint32_t u32Hclk)
{
if(CLK->PWRCTL & CLK_PWRCTL_HXT_EN) {
CLK_EnablePLL( CLK_PLLCTL_PLL_SRC_HXT,u32Hclk);
} else {
CLK_EnablePLL( CLK_PLLCTL_PLL_SRC_HIRC,u32Hclk);
}
CLK_WaitClockReady(CLK_CLKSTATUS_PLL_STB_Msk);
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_PLL,CLK_HCLK_CLK_DIVIDER(1));
return SystemCoreClock;
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Unlock protected registers */
SYS_UnlockReg();
/* Enable HIRC clock (Internal RC 22.1184MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);
/* Wait for HIRC clock ready */
CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);
/* Select HCLK clock source as HIRC and and HCLK source divider as 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV_HCLK(1));
/* Set P5 multi-function pins for crystal output/input */
SYS->P5_MFP &= ~(SYS_MFP_P50_Msk | SYS_MFP_P51_Msk);
SYS->P5_MFP |= (SYS_MFP_P50_XT1_IN | SYS_MFP_P51_XT1_OUT);
/* Enable HXT clock (external XTAL 12MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_XTLEN_HXT);
/* Wait for HXT clock ready */
CLK_WaitClockReady(CLK_STATUS_XTLSTB_Msk);
/* Set core clock as PLL_CLOCK from PLL */
CLK_SetCoreClock(PLL_CLOCK);
/* Enable UART module clock */
CLK_EnableModuleClock(UART0_MODULE);
/* Select UART module clock source as HXT and UART module clock divider as 1 */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_XTAL, CLK_CLKDIV_UART(1));
/* Lock protected registers */
SYS_LockReg();
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set P0 multi-function pins for UART RXD and TXD */
SYS->P1_MFP &= ~(SYS_MFP_P12_Msk | SYS_MFP_P13_Msk);
SYS->P1_MFP |= (SYS_MFP_P12_UART0_RXD | SYS_MFP_P13_UART0_TXD);
//SYS->P0_MFP &= ~(SYS_MFP_P01_Msk | SYS_MFP_P00_Msk);
//SYS->P0_MFP |= (SYS_MFP_P01_UART0_RXD | SYS_MFP_P00_UART0_TXD);
/* Set P3 multi-function pins for Clock Output */
SYS->P3_MFP = SYS_MFP_P36_CLKO;
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Unlock protected registers */
SYS_UnlockReg();
/* Set P5 multi-function pins for XTAL1 and XTAL2 */
SYS->P5_MFP &= ~(SYS_MFP_P50_Msk | SYS_MFP_P51_Msk);
SYS->P5_MFP |= (SYS_MFP_P50_XT1_IN | SYS_MFP_P51_XT1_OUT);
/* Enable external 12MHz XTAL (UART), HIRC */
CLK->PWRCTL = CLK_PWRCTL_XTL12M | CLK_PWRCTL_HIRCEN_Msk;
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_STATUS_XTLSTB_Msk | CLK_STATUS_HIRCSTB_Msk);
/* Switch HCLK clock source to XTL */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_XTAL,CLK_CLKDIV_HCLK(1));
/* Enable IP clock */
CLK->APBCLK = CLK_APBCLK_UART0CKEN_Msk | CLK_APBCLK_ADCCKEN_Msk | CLK_APBCLK_PWMCH01CKEN_Msk;
/* Select UART clock source from external crystal */
CLK->CLKSEL1 = (CLK->CLKSEL1 & ~CLK_CLKSEL1_UARTSEL_Msk) | CLK_CLKSEL1_UARTSEL_XTAL;
/* Select ADC clock source from external crystal */
CLK->CLKSEL1 = (CLK->CLKSEL1 & ~CLK_CLKSEL1_ADCSEL_Msk) | CLK_CLKSEL1_ADCSEL_XTAL;
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE,CLK_CLKSEL1_UARTSEL_XTAL,CLK_CLKDIV_UART(1));
CLK_SetModuleClock(ADC_MODULE,CLK_CLKSEL1_ADCSEL_XTAL,CLK_CLKDIV_ADC(6));
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate SystemCoreClock and CycylesPerUs automatically. */
SystemCoreClockUpdate();
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set P1 multi-function pins for UART RXD, TXD and ADC channel 5 input */
SYS->P1_MFP = SYS_MFP_P12_UART0_RXD | SYS_MFP_P13_UART0_TXD | SYS_MFP_P15_ADC_CH5;
/* Analog pin OFFD to prevent leakage */
P1->DINOFF |= (1 << 5) << GP_DINOFF_DINOFF0_Pos;
/* Set P2 multi-function pins for PWM Channel 0. */
SYS->P2_MFP = SYS_MFP_P22_PWM0_CH0;
/* Lock protected registers */
SYS_LockReg();
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Enable HIRC clock (Internal RC 22.1184MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);
/* Wait for HIRC clock ready */
CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);
/* Select HCLK clock source as HIRC and and HCLK source divider as 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV0_HCLK(1));
/* Set PLL to Power-down mode and PLLSTB bit in CLK_STATUS register will be cleared by hardware.*/
CLK_DisablePLL();
/* Enable HXT clock (external XTAL 12MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
/* Wait for HXT clock ready */
CLK_WaitClockReady(CLK_STATUS_HXTSTB_Msk);
/* Set core clock as PLL_CLOCK from PLL */
CLK_SetCoreClock(PLL_CLOCK);
/* Enable UART module clock */
CLK_EnableModuleClock(UART0_MODULE);
/* Select UART module clock source as HXT and UART module clock divider as 1 */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));
/* Enable DAC module clock */
CLK_EnableModuleClock(DAC_MODULE);
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set PD multi-function pins for UART0 RXD and TXD */
SYS->GPD_MFPL &= ~(SYS_GPD_MFPL_PD0MFP_Msk | SYS_GPD_MFPL_PD1MFP_Msk);
SYS->GPD_MFPL |= (SYS_GPD_MFPL_PD0MFP_UART0_RXD | SYS_GPD_MFPL_PD1MFP_UART0_TXD);
/* Set PB multi-function pins for DAC voltage output */
SYS->GPB_MFPL &= ~SYS_GPB_MFPL_PB0MFP_Msk;
SYS->GPB_MFPL |= SYS_GPB_MFPL_PB0MFP_DAC ;
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Enable Internal RC 22.1184MHz clock */
CLK_EnableXtalRC(CLK_PWRCON_OSC22M_EN_Msk);
/* Waiting for Internal RC clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_OSC22M_STB_Msk);
/* Switch HCLK clock source to Internal RC and HCLK source divide 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HIRC, CLK_CLKDIV_HCLK(1));
/* Enable external XTAL 12MHz clock */
CLK_EnableXtalRC(CLK_PWRCON_XTL12M_EN_Msk);
/* Waiting for external XTAL clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_XTL12M_STB_Msk);
/* Set core clock as PLL_CLOCK from PLL */
CLK_SetCoreClock(PLL_CLOCK);
/* Enable UART module clock */
CLK_EnableModuleClock(UART0_MODULE);
CLK_EnableModuleClock(UART1_MODULE);
/* Select UART module clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_CLKDIV_UART(1));
CLK_SetModuleClock(UART1_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_CLKDIV_UART(1));
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set GPB multi-function pins for UART0 RXD and TXD */
/* Set GPB multi-function pins for UART1 RXD, TXD, nRTS and nCTS */
SYS->GPB_MFP &= ~(SYS_GPB_MFP_PB0_Msk | SYS_GPB_MFP_PB1_Msk |
SYS_GPB_MFP_PB4_Msk | SYS_GPB_MFP_PB5_Msk |
SYS_GPB_MFP_PB6_Msk | SYS_GPB_MFP_PB7_Msk);
SYS->GPB_MFP |= (SYS_GPB_MFP_PB0_UART0_RXD | SYS_GPB_MFP_PB1_UART0_TXD |
SYS_GPB_MFP_PB4_UART1_RXD | SYS_GPB_MFP_PB5_UART1_TXD |
SYS_GPB_MFP_PB6_UART1_nRTS | SYS_GPB_MFP_PB7_UART1_nCTS);
SYS->ALT_MFP &= ~(SYS_ALT_MFP_PB6_Msk | SYS_ALT_MFP_PB7_Msk);
SYS->ALT_MFP |= SYS_ALT_MFP_PB6_UART1_nRTS | SYS_ALT_MFP_PB7_UART1_nCTS;
}
/*---------------------------------------------------------------------------------------------------------*/
void SYS_Init(void)
{
/* Unlock protected registers */
SYS_UnlockReg();
/* Set HCLK source form HXT and HCLK source divide 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_HCLK_CLK_DIVIDER(1));
/* Enable external 12MHz HXT, 32KHz LXT and HIRC */
CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk | CLK_PWRCTL_LXT_EN_Msk | CLK_PWRCTL_HIRC_EN_Msk);
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_HXT_STB_Msk | CLK_CLKSTATUS_LXT_STB_Msk | CLK_CLKSTATUS_HIRC_STB_Msk);
/* Set HCLK frequency 32MHz */
CLK_SetCoreClock(32000000);
CLK->AHBCLK |= CLK_AHBCLK_DMA_EN_Msk;
/* Enable IP clock */
CLK_EnableModuleClock(UART0_MODULE);
/* Enable ADC clock */
CLK_EnableModuleClock(ADC_MODULE);
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE,CLK_CLKSEL1_UART_S_HXT,CLK_UART_CLK_DIVIDER(1));
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set PA multi-function pins for UART0 RXD and TXD */
SYS->PB_L_MFP &= ~( SYS_PB_L_MFP_PB0_MFP_Msk | SYS_PB_L_MFP_PB1_MFP_Msk);
SYS->PB_L_MFP |= (SYS_PB_L_MFP_PB0_MFP_UART0_RX | SYS_PB_L_MFP_PB1_MFP_UART0_TX );
/* Set PB multi-function pins for Clock Output */
SYS->PB_H_MFP = ( SYS->PB_H_MFP & ~SYS_PB_H_MFP_PB12_MFP_Msk ) | SYS_PB_H_MFP_PB12_MFP_CKO;
/* Set PA.0,PA.1,PA.2,PA.3 multi-function pin for ADC channel 0,1,2,3 */
SYS->PA_L_MFP = (SYS->PA_L_MFP & ~SYS_PA_L_MFP_PA0_MFP_Msk) | SYS_PA_L_MFP_PA0_MFP_ADC_CH0;
SYS->PA_L_MFP = (SYS->PA_L_MFP & ~SYS_PA_L_MFP_PA1_MFP_Msk) | SYS_PA_L_MFP_PA1_MFP_ADC_CH1;
SYS->PA_L_MFP = (SYS->PA_L_MFP & ~SYS_PA_L_MFP_PA2_MFP_Msk) | SYS_PA_L_MFP_PA2_MFP_ADC_CH2;
SYS->PA_L_MFP = (SYS->PA_L_MFP & ~SYS_PA_L_MFP_PA3_MFP_Msk) | SYS_PA_L_MFP_PA3_MFP_ADC_CH3;
/* Disable PA.0 digital input path */
PA->OFFD |= ((1 << 0) << GP_OFFD_OFFD_Pos);
/* Lock protected registers */
SYS_LockReg();
}
/**
* This function will initial Clock tree.
*/
void clock_init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Unlock protected registers */
SYS_UnlockReg();
/* Enable External XTAL (4~24 MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
/* Waiting for 12MHz clock ready */
CLK_WaitClockReady( CLK_STATUS_HXTSTB_Msk);
/* Switch HCLK clock source to HXT */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HXT,CLK_CLKDIV0_HCLK(1));
/* Set PLL to power down mode and PLL_STB bit in CLKSTATUS register will be cleared by hardware.*/
CLK->PLLCTL |= CLK_PLLCTL_PD_Msk;
/* Set PLL frequency */
CLK->PLLCTL = CLK_PLLCTL_84MHz_HXT;
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_STATUS_PLLSTB_Msk);
/* Switch HCLK clock source to PLL */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_PLL,CLK_CLKDIV0_HCLK(1));
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate SystemCoreClock. */
SystemCoreClockUpdate();
/* Lock protected registers */
SYS_LockReg();
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Enable HIRC clock (Internal RC 22.1184MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HIRCEN_Msk);
/* Wait for HIRC clock ready */
CLK_WaitClockReady(CLK_STATUS_HIRCSTB_Msk);
/* Select HCLK clock source as HIRC and and HCLK source divider as 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_HIRC, CLK_CLKDIV0_HCLK(1));
/* Enable HXT clock (external XTAL 12MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HXTEN_Msk);
/* Wait for HXT clock ready */
CLK_WaitClockReady(CLK_STATUS_HXTSTB_Msk);
/* Set core clock as PLL_CLOCK from PLL */
CLK_SetCoreClock(PLL_CLOCK);
/* Enable UART module clock */
CLK_EnableModuleClock(UART0_MODULE);
CLK_EnableModuleClock(UART1_MODULE);
/* Select UART module clock source as HXT and UART module clock divider as 1 */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));
CLK_SetModuleClock(UART1_MODULE, CLK_CLKSEL1_UARTSEL_HXT, CLK_CLKDIV0_UART(1));
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set PD multi-function pins for UART0 RXD(PD.0) and TXD(PD.1) */
SYS->GPD_MFPL &= ~(SYS_GPD_MFPL_PD0MFP_Msk | SYS_GPD_MFPL_PD1MFP_Msk);
SYS->GPD_MFPL |= (SYS_GPD_MFPL_PD0MFP_UART0_RXD | SYS_GPD_MFPL_PD1MFP_UART0_TXD);
/* Set PB multi-function pins for UART1 RXD(PB.2), TXD(PB.3) and nCTS(PB.4) */
SYS->GPB_MFPL &= ~(SYS_GPB_MFPL_PB2MFP_Msk | SYS_GPB_MFPL_PB3MFP_Msk | SYS_GPB_MFPL_PB4MFP_Msk);
SYS->GPB_MFPL |= (SYS_GPB_MFPL_PB2MFP_UART1_RXD | SYS_GPB_MFPL_PB3MFP_UART1_TXD | SYS_GPB_MFPL_PB4MFP_UART1_nCTS);
/* Set PB multi-function pins for UART1 nRTS(PB.8) */
SYS->GPB_MFPH &= (~SYS_GPB_MFPH_PB8MFP_Msk);
SYS->GPB_MFPH |= SYS_GPB_MFPH_PB8MFP_UART1_nRTS;
}
void SysInit(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Unlock protected registers */
SYS_UnlockReg();
/* Enable External XTAL (4~24 MHz) */
CLK_EnableXtalRC(CLK_PWRCTL_HXT_EN_Msk);
/* Waiting for 12MHz clock ready */
CLK_WaitClockReady( CLK_CLKSTATUS_HXT_STB_Msk);
/* Switch HCLK clock source to HXT */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HXT,CLK_HCLK_CLK_DIVIDER(1));
/* Enable IP clock */
CLK_EnableModuleClock(UART0_MODULE);
CLK_EnableModuleClock(TMR0_MODULE);
CLK_EnableModuleClock(TMR1_MODULE);
/* Select IP clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_UART_CLK_DIVIDER(1));
CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR0_S_HXT, CLK_TMR0_CLK_DIVIDER(1));
CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR1_S_HXT, CLK_TMR1_CLK_DIVIDER(1));
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate SystemCoreClock. */
SystemCoreClockUpdate();
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set GPB multi-function pins for UART0 RXD and TXD */
SYS->PB_L_MFP &= ~(SYS_PB_L_MFP_PB0_MFP_Msk | SYS_PB_L_MFP_PB1_MFP_Msk);
SYS->PB_L_MFP |= (SYS_PB_L_MFP_PB0_MFP_UART0_TX | SYS_PB_L_MFP_PB1_MFP_UART0_RX);
/* Set Timer0 event counting/toggle out pin */
SYS->PB_H_MFP &= ~SYS_PB_H_MFP_PB8_MFP_Msk;
SYS->PB_H_MFP |= SYS_PB_H_MFP_PB8_MFP_TMR0_EXT;
/* Lock protected registers */
SYS_LockReg();
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Enable Internal RC 22.1184MHz clock */
CLK_EnableXtalRC(CLK_PWRCON_OSC22M_EN_Msk);
/* Waiting for Internal RC clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_OSC22M_STB_Msk);
/* Switch HCLK clock source to Internal RC and HCLK source divide 1 */
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_HIRC, CLK_CLKDIV_HCLK(1));
/* Enable external XTAL 12MHz clock */
CLK_EnableXtalRC(CLK_PWRCON_XTL12M_EN_Msk);
/* Waiting for external XTAL clock ready */
CLK_WaitClockReady(CLK_CLKSTATUS_XTL12M_STB_Msk);
/* Set core clock as PLL_CLOCK from PLL */
CLK_SetCoreClock(PLL_CLOCK);
/* Enable UART0 and UART1 module clock */
CLK_EnableModuleClock(UART0_MODULE);
CLK_EnableModuleClock(UART1_MODULE);
CLK_EnableModuleClock(TMR0_MODULE);
/* Select UART0 and UART1 module clock source */
CLK_SetModuleClock(UART0_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_CLKDIV_UART(1));
CLK_SetModuleClock(UART1_MODULE, CLK_CLKSEL1_UART_S_HXT, CLK_CLKDIV_UART(1));
CLK_SetModuleClock(TMR0_MODULE, CLK_CLKSEL1_TMR0_S_HXT, 0);
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set P3 multi-function pins for UART0 RXD and TXD */
SYS->P3_MFP &= ~(SYS_MFP_P30_Msk | SYS_MFP_P31_Msk);
SYS->P3_MFP |= (SYS_MFP_P30_RXD0 | SYS_MFP_P31_TXD0);
/* Set P0 multi-function pins for UART1 RXD and TXD */
SYS->P0_MFP &= ~(SYS_MFP_P00_Msk | SYS_MFP_P01_Msk);
SYS->P0_MFP |= (SYS_MFP_P00_TXD1 | SYS_MFP_P01_RXD1);
}
void SYS_Init(void)
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init System Clock */
/*---------------------------------------------------------------------------------------------------------*/
/* Unlock protected registers */
SYS_UnlockReg();
/* Enable external 12MHz XTAL (UART), HIRC */
CLK->PWRCTL = CLK_PWRCTL_XTL12M | CLK_PWRCTL_HIRCEN_Msk;
/* Waiting for clock ready */
CLK_WaitClockReady(CLK_STATUS_XTLSTB_Msk | CLK_STATUS_HIRCSTB_Msk);
/* Switch HCLK clock source to PLL */
CLK_SetHCLK(CLK_CLKSEL0_HCLKSEL_PLL,CLK_CLKDIV_HCLK(1));
/* Set core clock as PLL_CLOCK from PLL */
CLK_SetCoreClock(PLL_CLOCK);
/* Enable IP clock */
CLK->APBCLK = CLK_APBCLK_UART0CKEN_Msk | CLK_APBCLK_PWMCH01CKEN_Msk | CLK_APBCLK_PWMCH23CKEN_Msk | CLK_APBCLK_PWMCH45CKEN_Msk;
/* Select UART clock source from external crystal*/
CLK->CLKSEL1 = (CLK->CLKSEL1 & ~CLK_CLKSEL1_UARTSEL_Msk) | CLK_CLKSEL1_UARTSEL_XTAL;
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate SystemCoreClock and CycylesPerUs automatically. */
SystemCoreClockUpdate();
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set P1 multi-function pins for UART RXD, TXD */
SYS->P1_MFP = SYS_MFP_P12_UART0_RXD | SYS_MFP_P13_UART0_TXD;
/* Set P0 multi-function pins for PWM Channel 5 */
SYS->P0_MFP |= SYS_MFP_P04_PWM0_CH5;
/* Set P2 multi-function pins for PWM Channel 0~4 */
SYS->P2_MFP = SYS_MFP_P22_PWM0_CH0 | SYS_MFP_P23_PWM0_CH1 |
SYS_MFP_P24_PWM0_CH2 | SYS_MFP_P25_PWM0_CH3 | SYS_MFP_P26_PWM0_CH4;
/* Lock protected registers */
SYS_LockReg();
}
/**
* @brief This function set HCLK frequency. The frequency unit is Hz. The range of u32Hclk is 16 ~ 32 MHz
* @param u32Hclk is HCLK frequency
* @return HCLK frequency
*/
uint32_t CLK_SetCoreClock(uint32_t u32Hclk)
{
if(u32Hclk > FREQ_50MHZ)
u32Hclk = FREQ_50MHZ;
else if(u32Hclk < FREQ_25MHZ)
u32Hclk = FREQ_25MHZ;
if(CLK->PWRCON & CLK_PWRCON_XTL12M_EN_Msk)
u32Hclk = CLK_EnablePLL(CLK_PLLCON_PLL_SRC_HXT, u32Hclk);
else
u32Hclk = CLK_EnablePLL(CLK_PLLCON_PLL_SRC_HIRC, u32Hclk);
CLK_SetHCLK(CLK_CLKSEL0_HCLK_S_PLL, CLK_CLKDIV_HCLK(1));
return u32Hclk;
}
