/*FUNCTION**********************************************************************
*
* Function Name : I2C_DRV_SlaveInit
* Description : initializes the I2C module.
* This function will save the application callback info, turn on the clock of
* I2C instance, setup according to user configuration.
*
*END**************************************************************************/
void I2C_DRV_SlaveInit(uint32_t instance,
const i2c_slave_user_config_t * userConfigPtr,
i2c_slave_state_t * slave)
{
assert(slave);
assert(instance < HW_I2C_INSTANCE_COUNT);
uint32_t baseAddr = g_i2cBaseAddr[instance];
/* Exit if current instance is already initialized. */
if (g_i2cStatePtr[instance])
{
return;
}
/* Init driver instance structure */
memset(slave, 0, sizeof(i2c_slave_state_t));
slave->slaveListening = userConfigPtr->slaveListening;
slave->slaveCallback = userConfigPtr->slaveCallback;
slave->callbackParam = userConfigPtr->callbackParam;
/* Enable clock for I2C.*/
CLOCK_SYS_EnableI2cClock(instance);
/* Init instance to known state. */
I2C_HAL_Init(baseAddr);
/* Set slave address.*/
I2C_HAL_SetAddress7bit(baseAddr, userConfigPtr->address);
/* Save runtime structure pointer.*/
g_i2cStatePtr[instance] = slave;
/* Create Event for irqSync */
OSA_EventCreate(&slave->irqEvent, kEventAutoClear);
#if FSL_FEATURE_I2C_HAS_START_STOP_DETECT
/* Enable I2C START&STOP signal detect interrupt in the peripheral.*/
if(userConfigPtr->startStopDetect)
{
I2C_HAL_SetStartStopIntCmd(baseAddr,true);
}
#endif
#if FSL_FEATURE_I2C_HAS_STOP_DETECT
/* Enable STOP signal detect interrupt in the peripheral.*/
if(userConfigPtr->stopDetect)
{
I2C_HAL_SetStopIntCmd(baseAddr,true);
}
#endif
/* Enable I2C interrupt as default if setup slave listening mode */
I2C_HAL_SetIntCmd(baseAddr, slave->slaveListening);
/* Enable I2C interrupt from NVIC */
INT_SYS_EnableIRQ(g_i2cIrqId[instance]);
/* Enable the peripheral operation.*/
I2C_HAL_Enable(baseAddr);
}
/*!
* @brief The i2c slave
* The function runs i2c slave with polling mode (HAL layer). Slave receive data
* from master and echo back to master
*/
void main(void)
{
// Number byte data will be transfer
uint32_t count = 0;
// Buffer store data to transfer
uint8_t dataBuff[50] = {0};
// slave address
uint16_t address = 0x7FU;
// i2c slave base address
I2C_Type * baseAddr = (I2C_Type*)I2C0_BASE;
// Initialize hardware
hardware_init();
// Configure pin for i2c slave
configure_i2c_pins(BOARD_I2C_COMM_INSTANCE);
// Initialize uart to debug
dbg_uart_init();
printf("Slave is running ...");
/* Enable clock for I2C.*/
CLOCK_SYS_EnableI2cClock(BOARD_I2C_COMM_INSTANCE);
/* Init instance to known state. */
I2C_HAL_Init(baseAddr);
/* Set slave address.*/
I2C_HAL_SetAddress7bit(baseAddr, address);
/* Enable the peripheral operation.*/
I2C_HAL_Enable(baseAddr);
// Loop transfer
while(1)
{
// count is length of string
I2C_HAL_SlaveReceiveDataPolling(baseAddr, (uint8_t*)&count, 1);
// Slave receive buffer from master
I2C_HAL_SlaveReceiveDataPolling(baseAddr, dataBuff, count);
// Slave send buffer received from master
I2C_HAL_SlaveSendDataPolling(baseAddr, dataBuff, count);
}
}
void i2c_init(i2c_t *obj, PinName sda, PinName scl) {
uint32_t i2c_sda = pinmap_peripheral(sda, PinMap_I2C_SDA);
uint32_t i2c_scl = pinmap_peripheral(scl, PinMap_I2C_SCL);
obj->instance = pinmap_merge(i2c_sda, i2c_scl);
MBED_ASSERT((int)obj->instance != NC);
CLOCK_SYS_EnableI2cClock(obj->instance);
uint32_t i2c_addrs[] = I2C_BASE_ADDRS;
I2C_HAL_Init(i2c_addrs[obj->instance]);
I2C_HAL_Enable(i2c_addrs[obj->instance]);
I2C_HAL_SetIntCmd(i2c_addrs[obj->instance], true);
i2c_frequency(obj, 100000);
pinmap_pinout(sda, PinMap_I2C_SDA);
pinmap_pinout(scl, PinMap_I2C_SCL);
uint32_t port_addrs[] = PORT_BASE_ADDRS;
PORT_HAL_SetOpenDrainCmd(port_addrs[sda >> GPIO_PORT_SHIFT], sda & 0xFF, true);
PORT_HAL_SetOpenDrainCmd(port_addrs[scl >> GPIO_PORT_SHIFT], scl & 0xFF, true);
}