示例#1
0
/**
  * @brief  Configures the Ethernet Interface
  * @param  None
  * @retval None
  */
static void ETH_MACDMA_Config(void)
{
  ETH_InitTypeDef ETH_InitStructure;

  /* Enable ETHERNET clock  */
  RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_ETH_MAC | RCC_AHB1Periph_ETH_MAC_Tx |
                        RCC_AHB1Periph_ETH_MAC_Rx, ENABLE);

  /* Reset ETHERNET on AHB Bus */
  ETH_DeInit();

  /* Software reset */
  ETH_SoftwareReset();

  /* Wait for software reset */
  while (ETH_GetSoftwareResetStatus() == SET);

  /* ETHERNET Configuration --------------------------------------------------*/
  /* Call ETH_StructInit if you don't like to configure all ETH_InitStructure parameter */
  ETH_StructInit(&ETH_InitStructure);

  /* Fill ETH_InitStructure parametrs */
  /*------------------------   MAC   -----------------------------------*/
  
  ETH_InitStructure.ETH_AutoNegotiation = ETH_AutoNegotiation_Disable;
  ETH_InitStructure.ETH_Speed = ETH_Speed_100M;
  ETH_InitStructure.ETH_Mode = ETH_Mode_FullDuplex;
  ETH_InitStructure.ETH_LoopbackMode = ETH_LoopbackMode_Disable;
  ETH_InitStructure.ETH_RetryTransmission = ETH_RetryTransmission_Disable;
  ETH_InitStructure.ETH_AutomaticPadCRCStrip = ETH_AutomaticPadCRCStrip_Disable;
  ETH_InitStructure.ETH_ReceiveAll = ETH_ReceiveAll_Disable;   //------------------was set to disable
  ETH_InitStructure.ETH_BroadcastFramesReception = ETH_BroadcastFramesReception_Enable;
  ETH_InitStructure.ETH_PromiscuousMode = ETH_PromiscuousMode_Enable;
  ETH_InitStructure.ETH_MulticastFramesFilter = ETH_MulticastFramesFilter_Perfect;
  ETH_InitStructure.ETH_UnicastFramesFilter = ETH_UnicastFramesFilter_Perfect;
#ifdef CHECKSUM_BY_HARDWARE
  ETH_InitStructure.ETH_ChecksumOffload = ETH_ChecksumOffload_Enable;   ///------ was set to disable
#endif

  /*------------------------   DMA   -----------------------------------*/

  /* When we use the Checksum offload feature, we need to enable the Store and Forward mode:
  the store and forward guarantee that a whole frame is stored in the FIFO, so the MAC can insert/verify the checksum,
  if the checksum is OK the DMA can handle the frame otherwise the frame is dropped */
  ETH_InitStructure.ETH_DropTCPIPChecksumErrorFrame = ETH_DropTCPIPChecksumErrorFrame_Enable;  //// was set to enable
  ETH_InitStructure.ETH_ReceiveStoreForward = ETH_ReceiveStoreForward_Enable;
  ETH_InitStructure.ETH_TransmitStoreForward = ETH_TransmitStoreForward_Enable;

  ETH_InitStructure.ETH_ForwardErrorFrames = ETH_ForwardErrorFrames_Enable;
  ETH_InitStructure.ETH_ForwardUndersizedGoodFrames = ETH_ForwardUndersizedGoodFrames_Enable;
  ETH_InitStructure.ETH_SecondFrameOperate = ETH_SecondFrameOperate_Enable;
  ETH_InitStructure.ETH_AddressAlignedBeats = ETH_AddressAlignedBeats_Enable;
  ETH_InitStructure.ETH_FixedBurst = ETH_FixedBurst_Enable;
  ETH_InitStructure.ETH_RxDMABurstLength = ETH_RxDMABurstLength_32Beat;
  ETH_InitStructure.ETH_TxDMABurstLength = ETH_TxDMABurstLength_32Beat;
  ETH_InitStructure.ETH_DMAArbitration = ETH_DMAArbitration_RoundRobin_RxTx_2_1;

  /* Configure Ethernet */
  EthInitStatus = ETH_Init(&ETH_InitStructure, LAN8720_PHY_ADDRESS);
}
示例#2
0
文件: heth.c 项目: atikbif/Relkon7
unsigned long ENET_Configuration(void)
{
	unsigned long res=0;
	unsigned short tmp;

	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_ETH_MAC | RCC_AHBPeriph_ETH_MAC_Tx |
	                        RCC_AHBPeriph_ETH_MAC_Rx, ENABLE);

	ETH_DeInit();
	get_mac(mac);
	ETH_MACAddressConfig(ETH_MAC_Address0, mac);
	GPIO_ETH_MediaInterfaceConfig(GPIO_ETH_MediaInterface_RMII);

	ETH_SoftwareReset();
	while(ETH_GetSoftwareResetStatus()==SET) vTaskDelayUntil( &ExLastExecutionTime, ( portTickType ) 1 / portTICK_RATE_MS );
	ETH_StructInit(&ETH_InitStructure);


	ETH_InitStructure.ETH_AutoNegotiation = ETH_AutoNegotiation_Enable;
	ETH_InitStructure.ETH_Watchdog = ETH_Watchdog_Disable;
	ETH_InitStructure.ETH_Jabber = ETH_Jabber_Disable;
	ETH_InitStructure.ETH_JumboFrame = ETH_JumboFrame_Disable;
	ETH_InitStructure.ETH_InterFrameGap = ETH_InterFrameGap_64Bit;
	ETH_InitStructure.ETH_CarrierSense = ETH_CarrierSense_Enable;
	ETH_InitStructure.ETH_Speed = ETH_Speed_10M;
	ETH_InitStructure.ETH_ReceiveOwn = ETH_ReceiveOwn_Disable;
	ETH_InitStructure.ETH_LoopbackMode = ETH_LoopbackMode_Disable;
	ETH_InitStructure.ETH_Mode = ETH_Mode_FullDuplex;
	ETH_InitStructure.ETH_RetryTransmission = ETH_RetryTransmission_Disable;
	ETH_InitStructure.ETH_AutomaticPadCRCStrip = ETH_AutomaticPadCRCStrip_Disable;
	ETH_InitStructure.ETH_BackOffLimit = ETH_BackOffLimit_10;
	ETH_InitStructure.ETH_DeferralCheck = ETH_DeferralCheck_Disable;
	ETH_InitStructure.ETH_ReceiveAll = ETH_ReceiveAll_Enable;
	ETH_InitStructure.ETH_PassControlFrames = ETH_PassControlFrames_ForwardPassedAddrFilter;
	ETH_InitStructure.ETH_BroadcastFramesReception = ETH_BroadcastFramesReception_Disable;
	ETH_InitStructure.ETH_DestinationAddrFilter = ETH_DestinationAddrFilter_Normal;
	ETH_InitStructure.ETH_PromiscuousMode = ETH_PromiscuousMode_Disable;
	ETH_InitStructure.ETH_MulticastFramesFilter = ETH_MulticastFramesFilter_Perfect;
	ETH_InitStructure.ETH_UnicastFramesFilter = ETH_UnicastFramesFilter_Perfect;
	ETH_InitStructure.ETH_RxDMABurstLength = ETH_RxDMABurstLength_32Beat;
	ETH_InitStructure.ETH_TxDMABurstLength = ETH_TxDMABurstLength_32Beat;
	ETH_InitStructure.ETH_FlushReceivedFrame = ETH_FlushReceivedFrame_Enable;
	ETH_InitStructure.ETH_SecondFrameOperate = ETH_SecondFrameOperate_Enable;
	ETH_InitStructure.ETH_FixedBurst = ETH_FixedBurst_Enable;
	res = ETH_Init(&ETH_InitStructure, PHY_ADDRESS);

	ETH_DMAITConfig(ETH_DMA_IT_NIS | ETH_DMA_IT_R | ETH_DMA_IT_T, ENABLE);
	for(tmp=0;tmp<ETH_RXBUFNB;tmp++) Rx_Buff[tmp] = (unsigned long)&ETH_RX[tmp][0];
	for(tmp=0;tmp<ETH_TXBUFNB;tmp++) Tx_Buff[tmp] = (unsigned long)&ETH_TX[tmp][0];
	ETH_DMATxDescChainInit(DMATxDscrTab, (unsigned char*)Tx_Buff, ETH_TXBUFNB);
	ETH_DMARxDescChainInit(DMARxDscrTab, (unsigned char*)Rx_Buff, ETH_RXBUFNB);
	for(tmp=0;tmp<ETH_RXBUFNB;tmp++){ETH_DMARxDescReceiveITConfig(DMARxDscrTab+tmp, ENABLE);}
	ETH_Start();
	ETH_ResumeDMAReception();
	return(res);
}
uint8_t ETH_MACDMA_Config(void)
{
	uint8_t rval;
	ETH_InitTypeDef ETH_InitStructure; 
	
	//使能以太网时钟
	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_ETH_MAC | RCC_AHB1Periph_ETH_MAC_Tx |RCC_AHB1Periph_ETH_MAC_Rx, ENABLE);
                        
	ETH_DeInit();  								//AHB总线重启以太网
	ETH_SoftwareReset();  						//软件重启网络
	while (ETH_GetSoftwareResetStatus() == SET);//等待软件重启网络完成 
	ETH_StructInit(&ETH_InitStructure); 	 	//初始化网络为默认值  

	///网络MAC参数设置 
	ETH_InitStructure.ETH_AutoNegotiation = ETH_AutoNegotiation_Enable;   			//开启网络自适应功能
	ETH_InitStructure.ETH_LoopbackMode = ETH_LoopbackMode_Disable;					//关闭反馈
	ETH_InitStructure.ETH_RetryTransmission = ETH_RetryTransmission_Disable; 		//关闭重传功能
	ETH_InitStructure.ETH_AutomaticPadCRCStrip = ETH_AutomaticPadCRCStrip_Disable; 	//关闭自动去除PDA/CRC功能 
	ETH_InitStructure.ETH_ReceiveAll = ETH_ReceiveAll_Disable;						//关闭接收所有的帧
	ETH_InitStructure.ETH_BroadcastFramesReception = ETH_BroadcastFramesReception_Enable;//允许接收所有广播帧
	ETH_InitStructure.ETH_PromiscuousMode = ETH_PromiscuousMode_Disable;			//关闭混合模式的地址过滤  
	ETH_InitStructure.ETH_MulticastFramesFilter = ETH_MulticastFramesFilter_Perfect;//对于组播地址使用完美地址过滤   
	ETH_InitStructure.ETH_UnicastFramesFilter = ETH_UnicastFramesFilter_Perfect;	//对单播地址使用完美地址过滤 
#ifdef CHECKSUM_BY_HARDWARE
	ETH_InitStructure.ETH_ChecksumOffload = ETH_ChecksumOffload_Enable; 			//开启ipv4和TCP/UDP/ICMP的帧校验和卸载   
#endif
	//当我们使用帧校验和卸载功能的时候,一定要使能存储转发模式,存储转发模式中要保证整个帧存储在FIFO中,
	//这样MAC能插入/识别出帧校验值,当真校验正确的时候DMA就可以处理帧,否则就丢弃掉该帧
	ETH_InitStructure.ETH_DropTCPIPChecksumErrorFrame = ETH_DropTCPIPChecksumErrorFrame_Enable; //开启丢弃TCP/IP错误帧
	ETH_InitStructure.ETH_ReceiveStoreForward = ETH_ReceiveStoreForward_Enable;     //开启接收数据的存储转发模式    
	ETH_InitStructure.ETH_TransmitStoreForward = ETH_TransmitStoreForward_Enable;   //开启发送数据的存储转发模式  

	ETH_InitStructure.ETH_ForwardErrorFrames = ETH_ForwardErrorFrames_Disable;     	//禁止转发错误帧  
	ETH_InitStructure.ETH_ForwardUndersizedGoodFrames = ETH_ForwardUndersizedGoodFrames_Disable;	//不转发过小的好帧 
	ETH_InitStructure.ETH_SecondFrameOperate = ETH_SecondFrameOperate_Enable;  		//打开处理第二帧功能
	ETH_InitStructure.ETH_AddressAlignedBeats = ETH_AddressAlignedBeats_Enable;  	//开启DMA传输的地址对齐功能
	ETH_InitStructure.ETH_FixedBurst = ETH_FixedBurst_Enable;            			//开启固定突发功能    
	ETH_InitStructure.ETH_RxDMABurstLength = ETH_RxDMABurstLength_32Beat;     		//DMA发送的最大突发长度为32个节拍   
	ETH_InitStructure.ETH_TxDMABurstLength = ETH_TxDMABurstLength_32Beat;			//DMA接收的最大突发长度为32个节拍
	ETH_InitStructure.ETH_DMAArbitration = ETH_DMAArbitration_RoundRobin_RxTx_2_1;
	
	rval=ETH_Init(&ETH_InitStructure,LAN8720_PHY_ADDRESS);		//配置ETH
	if(rval==ETH_SUCCESS)//配置成功
	{
		ETH_DMAITConfig(ETH_DMA_IT_NIS|ETH_DMA_IT_R,ENABLE);  	//使能以太网接收中断	
	}
	return rval;
}
示例#4
0
/**
  * @brief  Configures the Ethernet Interface
  * @param  None
  * @retval None
  */
void Ethernet_Configuration(void)
{
	  ETH_InitTypeDef ETH_InitStructure;

	  GPIO_ETH_MediaInterfaceConfig(GPIO_ETH_MediaInterface_MII);

	  /* Reset ETHERNET on AHB Bus */
	  ETH_DeInit();

	  /* Software reset */
	  ETH_SoftwareReset();

	  /* Wait for software reset */
	  while(ETH_GetSoftwareResetStatus()==SET);

	  /* ETHERNET Configuration ------------------------------------------------------*/
	  /* Call ETH_StructInit if you don't like to configure all ETH_InitStructure parameter */
	  ETH_StructInit(&ETH_InitStructure);

	  /* Fill ETH_InitStructure parametrs */
	  /*------------------------   MAC   -----------------------------------*/
	  ETH_InitStructure.ETH_AutoNegotiation = ETH_AutoNegotiation_Enable  ;
	  //ETH_InitStructure.ETH_Speed = ETH_Speed_100M;
	  ETH_InitStructure.ETH_LoopbackMode = ETH_LoopbackMode_Disable;
	  //ETH_InitStructure.ETH_Mode = ETH_Mode_FullDuplex;
	  ETH_InitStructure.ETH_RetryTransmission = ETH_RetryTransmission_Disable;
	  ETH_InitStructure.ETH_AutomaticPadCRCStrip = ETH_AutomaticPadCRCStrip_Disable;
	  ETH_InitStructure.ETH_ReceiveAll = ETH_ReceiveAll_Enable;
	  ETH_InitStructure.ETH_BroadcastFramesReception = ETH_BroadcastFramesReception_Disable;
	  ETH_InitStructure.ETH_PromiscuousMode = ETH_PromiscuousMode_Disable;
	  ETH_InitStructure.ETH_MulticastFramesFilter = ETH_MulticastFramesFilter_Perfect;
	  ETH_InitStructure.ETH_UnicastFramesFilter = ETH_UnicastFramesFilter_Perfect;
	  /* Configure ETHERNET */
	  ETH_Init(&ETH_InitStructure, PHY_ADDRESS);

		ETH_DMAITConfig(ETH_DMA_IT_NIS | ETH_DMA_IT_R, ENABLE);
}
示例#5
0
/**
  * @brief  ETH_BSP_Config
  * @param  None
  * @retval None
  */
void ETH_BSP_Config(void)
{
#if 0
  RCC_ClocksTypeDef RCC_Clocks;
  
  /* Configure the GPIO ports for ethernet pins */
  ETH_GPIO_Config();
  
  /* Configure the Ethernet MAC/DMA */
  ETH_MACDMA_Config();

  if (EthInitStatus == 0)
  {
    _printf("Ethernet Init failed\n");
    while(1);
  }

  /* Configure the PHY to generate an interrupt on change of link status */
  //Eth_Link_PHYITConfig(DP83848_PHY_ADDRESS);
  Eth_Link_PHYITConfig(KS8721_PHY_ADDRESS);

  /* Configure the EXTI for Ethernet link status. */
  //Eth_Link_EXTIConfig();
#else

	ETH_InitTypeDef ETH_InitStructure;

	/* Enable ETHERNET clocks  */
	RCC_AHB1PeriphClockCmd(	  RCC_AHB1Periph_ETH_MAC
							| RCC_AHB1Periph_ETH_MAC_Tx
							| RCC_AHB1Periph_ETH_MAC_Rx
							| RCC_AHB1Periph_ETH_MAC_PTP, ENABLE);

	/* Enable SYSCFG clock */
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);

	/*Select RMII Interface*/
	SYSCFG_ETH_MediaInterfaceConfig(SYSCFG_ETH_MediaInterface_RMII);

	/* Reset ETHERNET on AHB Bus */
	ETH_DeInit();

	/* Software reset */
	ETH_SoftwareReset();

	/* Wait for software reset */
	while (ETH_GetSoftwareResetStatus() == SET);

	/* ETHERNET Configuration ------------------------------------------------------*/
	/* Call ETH_StructInit if you don't like to configure all ETH_InitStructure parameter */
	ETH_StructInit(&ETH_InitStructure);

	/* Fill ETH_InitStructure parametrs */
	/*------------------------   MAC   -----------------------------------*/
	ETH_InitStructure.ETH_AutoNegotiation			= ETH_AutoNegotiation_Disable  ;
	ETH_InitStructure.ETH_Speed						= ETH_Speed_100M;
	ETH_InitStructure.ETH_LoopbackMode				= ETH_LoopbackMode_Disable;
	ETH_InitStructure.ETH_Mode						= ETH_Mode_FullDuplex;
	ETH_InitStructure.ETH_RetryTransmission			= ETH_RetryTransmission_Disable;
	ETH_InitStructure.ETH_AutomaticPadCRCStrip		= ETH_AutomaticPadCRCStrip_Disable;
	ETH_InitStructure.ETH_ReceiveAll				= ETH_ReceiveAll_Enable;
	ETH_InitStructure.ETH_BroadcastFramesReception	= ETH_BroadcastFramesReception_Disable;
	ETH_InitStructure.ETH_PromiscuousMode			= ETH_PromiscuousMode_Disable;
	ETH_InitStructure.ETH_MulticastFramesFilter		= ETH_MulticastFramesFilter_Perfect;
	ETH_InitStructure.ETH_UnicastFramesFilter		= ETH_UnicastFramesFilter_Perfect;

	unsigned int PhyAddr;
	uint16_t reg2;
	uint16_t reg3;

	// read the ID for match
	for (PhyAddr = 1; 32 >= PhyAddr; PhyAddr++)
	{
		reg2 = ETH_ReadPHYRegister(PhyAddr,2);	//PHY_MICR_INT_EN ?
		reg3 = ETH_ReadPHYRegister(PhyAddr,3);

		if ((reg2 == 0x0022) && (reg3 == 0x1609))
			break;
	}

	if (PhyAddr > 32)
	{
		_CONSOLE(LogId, "Ethernet Phy Not Found\n\r");
		return;// 1;
	}

	/* Configure Ethernet */
	if (ETH_Init(&ETH_InitStructure, PhyAddr) == 0)
	{
		_CONSOLE(LogId, "Ethernet Initialization Failed\n\r");
		return;// 1;
	}

	_CONSOLE(LogId, "Check LAN LEDs\n\r");
  
#endif
}
示例#6
0
/**
  * @brief  Configures the Ethernet Interface
  * @param  None
  * @retval None
  */
void Ethernet_Configuration(void)
{
  ETH_InitTypeDef ETH_InitStructure;

  /* MII/RMII Media interface selection ------------------------------------------*/
#ifdef MII_MODE /* Mode MII with STM3210C-EVAL  */
  GPIO_ETH_MediaInterfaceConfig(GPIO_ETH_MediaInterface_MII);

  /* Get HSE clock = 25MHz on PA8 pin (MCO) */
  RCC_MCOConfig(RCC_MCO_HSE);

#elif defined RMII_MODE  /* Mode RMII with STM3210C-EVAL */
  GPIO_ETH_MediaInterfaceConfig(GPIO_ETH_MediaInterface_RMII);

//  /* Set PLL3 clock output to 50MHz (25MHz /5 *10 =50MHz) */
//  RCC_PLL3Config(RCC_PLL3Mul_10);
//  /* Enable PLL3 */
//  RCC_PLL3Cmd(ENABLE);
//  /* Wait till PLL3 is ready */
//  while (RCC_GetFlagStatus(RCC_FLAG_PLL3RDY) == RESET)
//  {}
//
//  /* Get PLL3 clock on PA8 pin (MCO) */
//  RCC_MCOConfig(RCC_MCO_PLL3CLK);
#endif

  /* Reset ETHERNET on AHB Bus */
  ETH_DeInit();

  /* Software reset */
  ETH_SoftwareReset();

  /* Wait for software reset */
  while (ETH_GetSoftwareResetStatus() == SET);

  /* ETHERNET Configuration ------------------------------------------------------*/
  /* Call ETH_StructInit if you don't like to configure all ETH_InitStructure parameter */
  ETH_StructInit(&ETH_InitStructure);

  /* Fill ETH_InitStructure parametrs */
  /*------------------------   MAC   -----------------------------------*/
  ETH_InitStructure.ETH_AutoNegotiation = ETH_AutoNegotiation_Enable  ;
  ETH_InitStructure.ETH_LoopbackMode = ETH_LoopbackMode_Disable;
  ETH_InitStructure.ETH_RetryTransmission = ETH_RetryTransmission_Disable;
  ETH_InitStructure.ETH_AutomaticPadCRCStrip = ETH_AutomaticPadCRCStrip_Disable;
  ETH_InitStructure.ETH_ReceiveAll = ETH_ReceiveAll_Disable;
  ETH_InitStructure.ETH_BroadcastFramesReception = ETH_BroadcastFramesReception_Enable;
  ETH_InitStructure.ETH_PromiscuousMode = ETH_PromiscuousMode_Disable;
  ETH_InitStructure.ETH_MulticastFramesFilter = ETH_MulticastFramesFilter_Perfect;
  ETH_InitStructure.ETH_UnicastFramesFilter = ETH_UnicastFramesFilter_Perfect;
#ifdef CHECKSUM_BY_HARDWARE
  ETH_InitStructure.ETH_ChecksumOffload = ETH_ChecksumOffload_Enable;
#endif

  /*------------------------   DMA   -----------------------------------*/  
  
  /* When we use the Checksum offload feature, we need to enable the Store and Forward mode: 
  the store and forward guarantee that a whole frame is stored in the FIFO, so the MAC can insert/verify the checksum, 
  if the checksum is OK the DMA can handle the frame otherwise the frame is dropped */
  ETH_InitStructure.ETH_DropTCPIPChecksumErrorFrame = ETH_DropTCPIPChecksumErrorFrame_Enable; 
  ETH_InitStructure.ETH_ReceiveStoreForward = ETH_ReceiveStoreForward_Enable;         
  ETH_InitStructure.ETH_TransmitStoreForward = ETH_TransmitStoreForward_Enable;     
 
  ETH_InitStructure.ETH_ForwardErrorFrames = ETH_ForwardErrorFrames_Disable;       
  ETH_InitStructure.ETH_ForwardUndersizedGoodFrames = ETH_ForwardUndersizedGoodFrames_Disable;   
  ETH_InitStructure.ETH_SecondFrameOperate = ETH_SecondFrameOperate_Enable;                                                          
  ETH_InitStructure.ETH_AddressAlignedBeats = ETH_AddressAlignedBeats_Enable;      
  ETH_InitStructure.ETH_FixedBurst = ETH_FixedBurst_Enable;                
  ETH_InitStructure.ETH_RxDMABurstLength = ETH_RxDMABurstLength_32Beat;          
  ETH_InitStructure.ETH_TxDMABurstLength = ETH_TxDMABurstLength_32Beat;                                                                 
  ETH_InitStructure.ETH_DMAArbitration = ETH_DMAArbitration_RoundRobin_RxTx_2_1;

  /* Configure Ethernet */
  ETH_Init(&ETH_InitStructure, PHY_ADDRESS);
  
  /* Enable the Ethernet Rx Interrupt */
  ETH_DMAITConfig(ETH_DMA_IT_NIS | ETH_DMA_IT_R, ENABLE);  
}
/*************************************************************************
 * Function Name: eth_bsp_init
 * Parameters:
 * Return:
 *
 * Description:
 *
 *************************************************************************/
int eth_bsp_init(void)
{
   //
   unsigned int PhyAddr;
   //
   GPIO_InitTypeDef GPIO_InitStructure;
   NVIC_InitTypeDef NVIC_InitStructure;
   ETH_InitTypeDef ETH_InitStructure;
   
   /*Set default MAC Address*/
   eth_stm32f4x7_info.mac_addr[0]=ETH_STM32F4X7_DEFAULT_MAC_ADDR0;
   eth_stm32f4x7_info.mac_addr[1]=ETH_STM32F4X7_DEFAULT_MAC_ADDR1;
   eth_stm32f4x7_info.mac_addr[2]=ETH_STM32F4X7_DEFAULT_MAC_ADDR2;
   eth_stm32f4x7_info.mac_addr[3]=ETH_STM32F4X7_DEFAULT_MAC_ADDR3;
   eth_stm32f4x7_info.mac_addr[4]=ETH_STM32F4X7_DEFAULT_MAC_ADDR4;
   eth_stm32f4x7_info.mac_addr[5]=ETH_STM32F4X7_DEFAULT_MAC_ADDR5;
   
   /* Enable ETHERNET clocks  */
   RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_ETH_MAC | RCC_AHB1Periph_ETH_MAC_Tx |
   RCC_AHB1Periph_ETH_MAC_Rx | RCC_AHB1Periph_ETH_MAC_PTP, ENABLE);
   
   
   /* Enable GPIOs clocks */
   RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA |	RCC_AHB1Periph_GPIOB |
   RCC_AHB1Periph_GPIOC | RCC_AHB1Periph_GPIOG, ENABLE);
   
   /* Enable SYSCFG clock */
   RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
   /*Select RMII Interface*/
   SYSCFG_ETH_MediaInterfaceConfig(SYSCFG_ETH_MediaInterface_RMII);
   
   /* ETHERNET pins configuration */
   /* PA
   ETH_RMII_REF_CLK: PA1
   ETH_RMII_MDIO: PA2
   ETH_RMII_MDINT: PA3
   ETH_RMII_CRS_DV: PA7
   */
   
   /* Configure PA1, PA2, PA3 and PA7*/
   GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1 | GPIO_Pin_2 | GPIO_Pin_3 | GPIO_Pin_7;
   GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
   GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
   GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
   GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
   GPIO_Init(GPIOA, &GPIO_InitStructure);
   
   /* Connect PA1, PA2, PA3 and PA7 to ethernet module*/
   GPIO_PinAFConfig(GPIOA, GPIO_PinSource1, GPIO_AF_ETH);
   GPIO_PinAFConfig(GPIOA, GPIO_PinSource2, GPIO_AF_ETH);
   GPIO_PinAFConfig(GPIOA, GPIO_PinSource3, GPIO_AF_ETH);
   GPIO_PinAFConfig(GPIOA, GPIO_PinSource7, GPIO_AF_ETH);
   
   /* PB
   ETH_RMII_TX_EN: PB11
   */
   
   /* Configure PB11*/
   GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
   GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
   GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
   GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
   GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
   GPIO_Init(GPIOB, &GPIO_InitStructure);
   
   /* Connect PB11 to ethernet module*/
   GPIO_PinAFConfig(GPIOB, GPIO_PinSource11, GPIO_AF_ETH);
   
   /* PC
   ETH_RMII_MDC: PC1
   ETH_RMII_RXD0: PC4
   ETH_RMII_RXD1: PC5
   */
   
   /* Configure PC1, PC4 and PC5*/
   GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1 | GPIO_Pin_4 | GPIO_Pin_5;
   GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
   GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
   GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
   GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
   GPIO_Init(GPIOC, &GPIO_InitStructure);
   
   /* Connect PC1, PC4 and PC5 to ethernet module*/
   GPIO_PinAFConfig(GPIOC, GPIO_PinSource1, GPIO_AF_ETH);
   GPIO_PinAFConfig(GPIOC, GPIO_PinSource4, GPIO_AF_ETH);
   GPIO_PinAFConfig(GPIOC, GPIO_PinSource5, GPIO_AF_ETH);
   
   /* PG
   ETH_RMII_TXD0: PG13
   ETH_RMII_TXD1: PG14
   */
   
   /* Configure PG14 and PG15*/
   GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13 | GPIO_Pin_14;
   GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
   GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
   GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
   GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
   GPIO_Init(GPIOG, &GPIO_InitStructure);
   
   /* Connect PG13 and PG15 to ethernet module*/
   GPIO_PinAFConfig(GPIOG, GPIO_PinSource13, GPIO_AF_ETH);
   GPIO_PinAFConfig(GPIOG, GPIO_PinSource14, GPIO_AF_ETH);
 
#if 0
   /* Reset ETHERNET on AHB Bus */
   ETH_DeInit();
   
   /* Software reset */
   ETH_SoftwareReset();
   
   /* Wait for software reset */
   while(ETH_GetSoftwareResetStatus()==SET);
   
   /* ETHERNET Configuration ------------------------------------------------------*/
   /* Call ETH_StructInit if you don't like to configure all ETH_InitStructure parameter */
   ETH_StructInit(&ETH_InitStructure);
   
   /* Fill ETH_InitStructure parametrs */
   /*------------------------   MAC   -----------------------------------*/
   //ETH_InitStructure.ETH_AutoNegotiation = ETH_AutoNegotiation_Disable  ;
   ETH_InitStructure.ETH_AutoNegotiation = ETH_AutoNegotiation_Enable;
   //ETH_InitStructure.ETH_Speed = ETH_Speed_100M;
   ETH_InitStructure.ETH_LoopbackMode = ETH_LoopbackMode_Disable;
   //ETH_InitStructure.ETH_Mode = ETH_Mode_FullDuplex;
   ETH_InitStructure.ETH_RetryTransmission = ETH_RetryTransmission_Disable;
   ETH_InitStructure.ETH_AutomaticPadCRCStrip = ETH_AutomaticPadCRCStrip_Disable;
   ETH_InitStructure.ETH_ReceiveAll = ETH_ReceiveAll_Enable;
   ETH_InitStructure.ETH_BroadcastFramesReception = ETH_BroadcastFramesReception_Disable;
   ETH_InitStructure.ETH_PromiscuousMode = ETH_PromiscuousMode_Disable;
   ETH_InitStructure.ETH_MulticastFramesFilter = ETH_MulticastFramesFilter_Perfect;
   ETH_InitStructure.ETH_UnicastFramesFilter = ETH_UnicastFramesFilter_Perfect;
   ETH_InitStructure.ETH_Mode = ETH_Mode_FullDuplex;
   ETH_InitStructure.ETH_Speed = ETH_Speed_100M;
   
   // read the ID for match
   for(PhyAddr = 1; 32 >= PhyAddr; PhyAddr++)
   {
      if((0x0022 == ETH_ReadPHYRegister(PhyAddr,2))
            && (0x1619 == (ETH_ReadPHYRegister(PhyAddr,3)))) break;
   }
   //
   if(32 < PhyAddr)
   {
      //printf("Ethernet Phy Not Found\n\r");
      return -1;
   }
   /* Configure Ethernet */
   if(0 == ETH_Init(&ETH_InitStructure, PhyAddr))
   {
      //printf("Ethernet Initialization Failed\n\r");
      return -1;
   }
#endif
   //
   if(eth_macdma_config()<0)
     return -1;
   //
   return 0;//no error
}
示例#8
0
/**
  * @brief  Configures the DP83848V : Ethernet RMII Interface.
  * @param  None
  * @retval None
  */
void ET_STM32_ETH_Configuration(void)
{
  vu32 Value = 0;
  GPIO_InitTypeDef  GPIO_InitStructure;
  ETH_InitTypeDef   ETH_InitStructure;
  
  /* Enable ETHERNET Clock  */
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_ETH_MAC    | 
                        RCC_AHBPeriph_ETH_MAC_Tx |
                        RCC_AHBPeriph_ETH_MAC_Rx, ENABLE);

  // Start Initial GPIO For Interface DP83848V
  // Initial ET-STM32F ARM KIT Ethernet Interface = RMII Mode
  // PA1  <- ETH_RMII_REF_CLK(Default)
  // PA2  -> ETH_RMII_MDIO(Default)
  // PA8  -> MCO(Default)
  // PB11 -> ETH_RMII_TXEN(Default)
  // PB12 -> ETH_RMII_TXD0(Default)
  // PB13 -> ETH_RMII_TXD1(Default)
  // PC1  -> ETH_RMII_MDC(Default)
  // PD8  <- ETH_RMII_RXDV(Remap)
  // PD9  <- ETH_RMII_RXD0(Remap)
  // PD10 <- ETH_RMII_RXD1(Remap)

  // Configure PA2 as alternate function push-pull 
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_2;				//PA2 = ETH_RMII_MDIO
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  GPIO_Init(GPIOA, &GPIO_InitStructure);

  // Configure PC1 as alternate function push-pull 
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;				//PC1 = ETH_RMII_MDC
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  GPIO_Init(GPIOC, &GPIO_InitStructure);

  // Configure PB11, PB12 and PB13 as alternate function push-pull 
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11 |			//PB11 = ETH_RMII_TXEN 
                                GPIO_Pin_12 | 		  	//PB12 = ETH_RMII_TXD0
								GPIO_Pin_13;			//PB13 = ETH_RMII_TXD1
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  GPIO_Init(GPIOB, &GPIO_InitStructure);
  
  // Configure PA1 as input 
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;				//PA1 = ETH_RMII_REF_CLK
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
  GPIO_Init(GPIOA, &GPIO_InitStructure);

  // ETHERNET pins remapp in ET-STM32F ARM KIT board: RX_DV and RxD[1:0] 
  // PD8=CRS_DV(RMII Remap)
  // PD9=RXD0(RMII Remap)
  // PD10=RXD1(RMII Remap)
  GPIO_PinRemapConfig(GPIO_Remap_ETH, ENABLE);

  // Configure PD8, PD9, PD10 as input 
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8 | 			//PD8  = ETH_RMII_RX_DV
  							    GPIO_Pin_9 | 			//PD9  = ETH_RMII_RXD0
								GPIO_Pin_10;			//PD10 = ETH_RMII_RXD1
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
  GPIO_Init(GPIOD, &GPIO_InitStructure);

  
  /* Start of Config MCO Clock = 50MHz on PA8 */
  // Configure MCO (PA8) as alternate function push-pull 
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8; 			//PA8 = MCO
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  GPIO_Init(GPIOA, &GPIO_InitStructure);

  // set PLL3 clock output to 50MHz (25MHz / 5 * 10 = 50MHz) 
  RCC_PLL3Config(RCC_PLL3Mul_10);

  // Enable PLL3 
  RCC_PLL3Cmd(ENABLE);

  // Wait till PLL3 is ready 
  while (RCC_GetFlagStatus(RCC_FLAG_PLL3RDY) == RESET){}

  // Get clock PLL3 clock on PA8 pin 
  RCC_MCOConfig(RCC_MCO_PLL3CLK); 
  /*End of Initial MCO Clock = 50MHz on PA8	*/
  
  //Initial Ethernet Interface = RMII Mode      
  GPIO_ETH_MediaInterfaceConfig(GPIO_ETH_MediaInterface_RMII);
   
  /* Reset ETHERNET on AHB Bus */
  ETH_DeInit();
  
  /* Software reset */ 
  ETH_SoftwareReset();
  
  /* Wait for software reset */
  while(ETH_GetSoftwareResetStatus()==SET);

  /* ETHERNET Configuration ------------------------------------------------------*/
  /* Call ETH_StructInit if you don't like to configure all ETH_InitStructure parameter */
  ETH_StructInit(&ETH_InitStructure);
  
  /* Fill ETH_InitStructure parametrs */
  /*------------------------   MAC   -----------------------------------*/
  ETH_InitStructure.ETH_AutoNegotiation = ETH_AutoNegotiation_Enable  ;  

  //ETH_InitStructure.ETH_Speed = ETH_Speed_100M;  //Test 100 MHz

  ETH_InitStructure.ETH_LoopbackMode = ETH_LoopbackMode_Disable;              

  //ETH_InitStructure.ETH_Mode = ETH_Mode_FullDuplex;  //Test

  ETH_InitStructure.ETH_RetryTransmission = ETH_RetryTransmission_Disable;                                                                                  
  ETH_InitStructure.ETH_AutomaticPadCRCStrip = ETH_AutomaticPadCRCStrip_Disable;                                                                                                                                                                        
  ETH_InitStructure.ETH_ReceiveAll = ETH_ReceiveAll_Enable;                                                                                                       
  ETH_InitStructure.ETH_BroadcastFramesReception = ETH_BroadcastFramesReception_Disable;      
  ETH_InitStructure.ETH_PromiscuousMode = ETH_PromiscuousMode_Disable;                                                             
  ETH_InitStructure.ETH_MulticastFramesFilter = ETH_MulticastFramesFilter_Perfect;      
  ETH_InitStructure.ETH_UnicastFramesFilter = ETH_UnicastFramesFilter_Perfect;                        

  /* Configure ETHERNET */
  Value = ETH_Init(&ETH_InitStructure, PHY_ADDRESS); 
}
示例#9
0
static int eth_init(struct driver * driver)
{
	struct eth_attr *attr = (struct eth_attr *)driver->attr;
	unsigned char i;
	
	for(i=0; i<3; i++) {
		if(rcc_config(driver->rcc+i, (GB_StateType)ENABLE))
			return -1;
	}
	
  ETH_SoftwareReset();/* Software reset */
  while (ETH_GetSoftwareResetStatus() == SET);/* Wait for software reset */

	ETH_InitTypeDef ETH_InitStructure;
	/* ETHERNET Configuration --------------------------------------------------*/
  /* Call ETH_StructInit if you don't like to configure all ETH_InitStructure parameter */
  ETH_StructInit(&ETH_InitStructure);

  /* Fill ETH_InitStructure parametrs */
  /*------------------------   MAC   -----------------------------------*/
  ETH_InitStructure.ETH_AutoNegotiation = ETH_AutoNegotiation_Enable;
//	ETH_InitStructure.ETH_AutoNegotiation = ETH_AutoNegotiation_Disable;
//	ETH_InitStructure.ETH_Speed = ETH_Speed_10M;
//	ETH_InitStructure.ETH_Mode = ETH_Mode_FullDuplex;
  ETH_InitStructure.ETH_LoopbackMode = ETH_LoopbackMode_Disable;
  ETH_InitStructure.ETH_RetryTransmission = ETH_RetryTransmission_Disable;
  ETH_InitStructure.ETH_AutomaticPadCRCStrip = ETH_AutomaticPadCRCStrip_Disable;
  ETH_InitStructure.ETH_ReceiveAll = ETH_ReceiveAll_Disable;
  ETH_InitStructure.ETH_BroadcastFramesReception = ETH_BroadcastFramesReception_Enable;
  ETH_InitStructure.ETH_PromiscuousMode = ETH_PromiscuousMode_Disable;
  ETH_InitStructure.ETH_MulticastFramesFilter = ETH_MulticastFramesFilter_Perfect;
  ETH_InitStructure.ETH_UnicastFramesFilter = ETH_UnicastFramesFilter_Perfect;
#ifdef CHECKSUM_BY_HARDWARE
  ETH_InitStructure.ETH_ChecksumOffload = ETH_ChecksumOffload_Enable;
#endif	

  /*------------------------   DMA   -----------------------------------*/
  /* When we use the Checksum offload feature, we need to enable the Store and Forward mode:
  the store and forward guarantee that a whole frame is stored in the FIFO, so the MAC can insert/verify the checksum,
  if the checksum is OK the DMA can handle the frame otherwise the frame is dropped */
  ETH_InitStructure.ETH_DropTCPIPChecksumErrorFrame = ETH_DropTCPIPChecksumErrorFrame_Enable;
  ETH_InitStructure.ETH_ReceiveStoreForward = ETH_ReceiveStoreForward_Enable;
  ETH_InitStructure.ETH_TransmitStoreForward = ETH_TransmitStoreForward_Enable;

  ETH_InitStructure.ETH_ForwardErrorFrames = ETH_ForwardErrorFrames_Disable;
  ETH_InitStructure.ETH_ForwardUndersizedGoodFrames = ETH_ForwardUndersizedGoodFrames_Disable;
  ETH_InitStructure.ETH_SecondFrameOperate = ETH_SecondFrameOperate_Enable;
  ETH_InitStructure.ETH_AddressAlignedBeats = ETH_AddressAlignedBeats_Enable;
  ETH_InitStructure.ETH_FixedBurst = ETH_FixedBurst_Enable;
  ETH_InitStructure.ETH_RxDMABurstLength = ETH_RxDMABurstLength_32Beat;
  ETH_InitStructure.ETH_TxDMABurstLength = ETH_TxDMABurstLength_32Beat;
  ETH_InitStructure.ETH_DMAArbitration = ETH_DMAArbitration_RoundRobin_RxTx_2_1;

  /* Configure Ethernet */
	if(ETH_SUCCESS == ETH_Init(&ETH_InitStructure, attr->phy_addr))
		ETH_DMAITConfig(ETH_DMA_IT_NIS | ETH_DMA_IT_R, ENABLE);
	else
		return -1;

return 0;
}