/**
* @brief This function send nb_data pointed with *buf with the pipe number specified
*
*
* @param pipe
* @param nb_data
* @param buf
* @param handle call back function pointer
*
* @return status
*/
U8 host_send_data_interrupt(U8 pipe, U16 nb_data, U8 *buf, void(*handle)(U8 status, U16 nb_byte))
{
U8 i;
U8 *ptr_buf=buf;
Host_select_pipe(pipe);
if(it_pipe_str[pipe].enable==ENABLE)
{
return HOST_FALSE;
}
else
{
if(is_any_interrupt_pipe_active()==FALSE)
{
g_sav_int_sof_enable=Is_host_sof_interrupt_enabled();
Host_enable_sof_interrupt();
}
it_pipe_str[pipe].enable=ENABLE;
it_pipe_str[pipe].nb_byte_to_process=nb_data;
it_pipe_str[pipe].nb_byte_processed=0;
it_pipe_str[pipe].ptr_buf=buf;
it_pipe_str[pipe].handle=handle;
it_pipe_str[pipe].timeout=0;
it_pipe_str[pipe].nak_timeout=NAK_SEND_TIMEOUT;
it_pipe_str[pipe].nb_byte_on_going=0;
Host_reset_pipe(pipe);
Host_unfreeze_pipe();
// Prepare data to be sent
i = Host_get_pipe_length();
if ( i > nb_data) // Pipe size> remaining data
{
i = nb_data;
nb_data = 0;
}
else // Pipe size < remaining data
{
nb_data -= i;
}
it_pipe_str[pipe].nb_byte_on_going+=i; // Update nb data processed
while (i!=0) // Load Pipe buffer
{ Host_write_byte(*ptr_buf++); i--;
}
private_sof_counter=0; // Reset the counter in SOF detection sub-routine
it_pipe_str[pipe].timeout=0; // Refresh timeout counter
Host_ack_out_sent();
Host_ack_stall();
Host_ack_nak_received();
Host_enable_stall_interrupt();
Host_enable_error_interrupt();
#if (NAK_TIMEOUT_ENABLE==ENABLE)
Host_enable_nak_interrupt();
#endif
Host_enable_transmit_interrupt();
Host_send_out(); // Send the USB frame
return HOST_TRUE;
}
}
//!
//! @brief This function sends nb_data bytes pointed to by ptr_buf on the specified pipe.
//!
//! @param pipe
//! @param nb_data
//! @param ptr_buf
//! @param handler Call-back function pointer
//!
//! @return bool: Status
//!
bool host_send_data_interrupt(uint8_t pipe, uint16_t nb_data, const void *ptr_buf, Pipe_handler *handler)
{
bool sav_glob_int_en;
if (it_pipe_str[pipe].enable) return false;
if (!is_any_interrupt_pipe_active())
{
g_sav_int_sof_enable = Is_host_sof_interrupt_enabled();
Host_enable_sof_interrupt();
}
it_pipe_str[pipe].enable = true;
it_pipe_str[pipe].nb_byte_to_process = nb_data;
it_pipe_str[pipe].nb_byte_processed = 0;
it_pipe_str[pipe].ptr_buf = (void *)ptr_buf;
it_pipe_str[pipe].handler = handler;
it_pipe_str[pipe].timeout = 0;
it_pipe_str[pipe].nak_timeout = NAK_SEND_TIMEOUT;
if ((sav_glob_int_en = cpu_irq_is_enabled())) cpu_irq_disable();
Host_reset_pipe(pipe);
(void)Is_host_resetting_pipe(pipe);
if (sav_glob_int_en) cpu_irq_enable();
Host_configure_pipe_token(pipe, TOKEN_OUT);
Host_ack_out_ready(pipe);
Host_unfreeze_pipe(pipe);
// Prepare data to be sent
Host_reset_pipe_fifo_access(pipe);
it_pipe_str[pipe].nb_byte_on_going = nb_data - host_write_p_txpacket(pipe, ptr_buf, nb_data, NULL);
private_sof_counter = 0; // Reset the counter in SOF detection subroutine
it_pipe_str[pipe].timeout = 0; // Refresh time-out counter
if ((sav_glob_int_en = cpu_irq_is_enabled())) cpu_irq_disable();
Host_ack_out_ready(pipe);
Host_ack_stall(pipe);
Host_ack_nak_received(pipe);
(void)Is_host_nak_received(pipe);
if (sav_glob_int_en) cpu_irq_enable();
Host_enable_stall_interrupt(pipe);
Host_enable_pipe_error_interrupt(pipe);
#if NAK_TIMEOUT_ENABLE == ENABLE
Host_enable_nak_received_interrupt(pipe);
#endif
Host_enable_out_ready_interrupt(pipe);
Host_enable_pipe_interrupt(pipe);
Host_send_out(pipe); // Send the USB frame
return true;
}
//!
//! @brief This function receives nb_data bytes pointed to by ptr_buf on the specified pipe.
//!
//! *nb_data is updated with the final number of data bytes received.
//!
//! @param pipe
//! @param nb_data
//! @param ptr_buf
//! @param handler Call-back function pointer
//!
//! @return bool: Status
//!
bool host_get_data_interrupt(uint8_t pipe, uint16_t nb_data, void *ptr_buf, Pipe_handler *handler)
{
bool sav_glob_int_en;
if (it_pipe_str[pipe].enable) return false;
if (!is_any_interrupt_pipe_active())
{
g_sav_int_sof_enable = Is_host_sof_interrupt_enabled();
Host_enable_sof_interrupt();
}
it_pipe_str[pipe].enable = true;
it_pipe_str[pipe].nb_byte_to_process = nb_data;
it_pipe_str[pipe].nb_byte_processed = 0;
it_pipe_str[pipe].ptr_buf = ptr_buf;
it_pipe_str[pipe].handler = handler;
it_pipe_str[pipe].timeout = 0;
it_pipe_str[pipe].nak_timeout = NAK_RECEIVE_TIMEOUT;
private_sof_counter = 0; // Reset the counter in SOF detection subroutine
if ((sav_glob_int_en = cpu_irq_is_enabled())) cpu_irq_disable();
Host_reset_pipe(pipe);
Host_ack_stall(pipe);
Host_ack_nak_received(pipe);
(void)Is_host_nak_received(pipe);
if (sav_glob_int_en) cpu_irq_enable();
Host_enable_stall_interrupt(pipe);
#if NAK_TIMEOUT_ENABLE == ENABLE
Host_enable_nak_received_interrupt(pipe);
#endif
Host_enable_pipe_error_interrupt(pipe);
Host_enable_in_received_interrupt(pipe);
Host_enable_pipe_interrupt(pipe);
Host_enable_continuous_in_mode(pipe);
Host_configure_pipe_token(pipe, TOKEN_IN);
Host_ack_in_received(pipe);
Host_unfreeze_pipe(pipe);
return true;
}
/**
* @brief This function receives nb_data pointed with *buf with the pipe number specified
*
* The nb_data parameter is passed as a U16 pointer, thus the data pointed by this pointer
* is updated with the final number of data byte received.
*
* @param pipe
* @param nb_data
* @param buf
* @param handle call back function pointer
*
* @return status
*/
U8 host_get_data_interrupt(U8 pipe, U16 nb_data, U8 *buf,void(*handle)(U8 status, U16 nb_byte))
{
Host_select_pipe(pipe);
if(it_pipe_str[pipe].enable==ENABLE)
{
return HOST_FALSE;
}
else
{
if(is_any_interrupt_pipe_active()==FALSE)
{
g_sav_int_sof_enable=Is_host_sof_interrupt_enabled();
Host_enable_sof_interrupt();
}
it_pipe_str[pipe].enable=ENABLE;
it_pipe_str[pipe].nb_byte_to_process=nb_data;
it_pipe_str[pipe].nb_byte_processed=0;
it_pipe_str[pipe].ptr_buf=buf;
it_pipe_str[pipe].handle=handle;
it_pipe_str[pipe].timeout=0;
it_pipe_str[pipe].nak_timeout=NAK_RECEIVE_TIMEOUT;
private_sof_counter=0; // Reset the counter in SOF detection sub-routine
Host_reset_pipe(pipe);
Host_enable_stall_interrupt();
#if (NAK_TIMEOUT_ENABLE==ENABLE)
Host_enable_nak_interrupt();
#endif
Host_enable_error_interrupt();
Host_enable_receive_interrupt();
Host_ack_stall();
Host_ack_nak_received();
Host_continuous_in_mode();
Host_set_token_in();
Host_ack_in_received();
Host_unfreeze_pipe();
return HOST_TRUE;
}
}
//! This function is the generic control pipe management function.
//! This function is used to send and receive control requests over control pipe.
//!
//! @todo Fix all time-out errors and disconnections in active wait loop.
//!
//! @param data_pointer void *: Pointer to data to transfer
//!
//! @return Status_t: Status
//!
//! @note This function uses the usb_request global structure. Hence, this
//! structure should be filled before calling this function.
//!
Status_t host_transfer_control(void *data_pointer)
{
int status = CONTROL_GOOD;
bool sav_int_sof_enable;
bool sav_glob_int_en;
uint16_t data_length;
uint8_t c;
Usb_ack_event(EVT_HOST_SOF);
sav_int_sof_enable = Is_host_sof_interrupt_enabled();
Host_enable_sof_interrupt(); // SOF software detection is in interrupt subroutine
while (!Is_usb_event(EVT_HOST_SOF)) // Wait 1 SOF
{
#if defined(Host_wait_action)
Host_wait_action();
#endif
if (Is_host_emergency_exit())
{
Host_freeze_pipe(P_CONTROL);
Host_reset_pipe(P_CONTROL);
status = CONTROL_TIMEOUT;
goto host_transfer_control_end;
}
}
Host_configure_pipe_token(P_CONTROL, TOKEN_SETUP);
Host_ack_setup_ready();
Host_unfreeze_pipe(P_CONTROL);
// Build and send the setup request fields
Host_reset_pipe_fifo_access(P_CONTROL);
Host_write_pipe_data(P_CONTROL, 8, usb_request.bmRequestType);
Host_write_pipe_data(P_CONTROL, 8, usb_request.bRequest);
Host_write_pipe_data(P_CONTROL, 16, usb_format_mcu_to_usb_data(16, usb_request.wValue));
Host_write_pipe_data(P_CONTROL, 16, usb_format_mcu_to_usb_data(16, usb_request.wIndex));
Host_write_pipe_data(P_CONTROL, 16, usb_format_mcu_to_usb_data(16, usb_request.wLength));
Host_send_setup();
while (!Is_host_setup_ready()) // Wait for SETUP ack
{
#if defined(Host_wait_action)
Host_wait_action();
#endif
if (Is_host_emergency_exit())
{
Host_freeze_pipe(P_CONTROL);
Host_reset_pipe(P_CONTROL);
status = CONTROL_TIMEOUT;
goto host_transfer_control_end;
}
if (Is_host_pipe_error(P_CONTROL)) // Any error?
{
c = Host_error_status(P_CONTROL);
Host_ack_all_errors(P_CONTROL);
status = c; // Send error status
goto host_transfer_control_end;
}
}
// Setup token sent; now send IN or OUT token
// Before just wait 1 SOF
Usb_ack_event(EVT_HOST_SOF);
Host_freeze_pipe(P_CONTROL);
data_length = usb_request.wLength;
while (!Is_usb_event(EVT_HOST_SOF)) // Wait 1 SOF
{
#if defined(Host_wait_action)
Host_wait_action();
#endif
if (Is_host_emergency_exit())
{
Host_freeze_pipe(P_CONTROL);
Host_reset_pipe(P_CONTROL);
status = CONTROL_TIMEOUT;
goto host_transfer_control_end;
}
}
// IN request management ---------------------------------------------
if (usb_request.bmRequestType & 0x80) // Data stage IN (bmRequestType.D7 == 1)
{
Host_disable_continuous_in_mode(P_CONTROL);
Host_configure_pipe_token(P_CONTROL, TOKEN_IN);
Host_ack_control_in_received_free();
while (data_length)
{
Host_unfreeze_pipe(P_CONTROL);
private_sof_counter = 0; // Reset the counter in SOF detection subroutine
while (!Is_host_control_in_received())
{
#if defined(Host_wait_action)
Host_wait_action();
#endif
if (Is_host_emergency_exit())
{
Host_freeze_pipe(P_CONTROL);
Host_reset_pipe(P_CONTROL);
status = CONTROL_TIMEOUT;
goto host_transfer_control_end;
}
if (Is_host_pipe_error(P_CONTROL)) // Any error?
{
c = Host_error_status(P_CONTROL);
Host_ack_all_errors(P_CONTROL);
status = c; // Send error status
goto host_transfer_control_end;
}
if (Is_host_stall(P_CONTROL))
{
Host_ack_stall(P_CONTROL);
status = CONTROL_STALL;
goto host_transfer_control_end;
}
#if TIMEOUT_DELAY_ENABLE == ENABLE
if (1000 < host_get_timeout()) // Count 1s
{
Host_freeze_pipe(P_CONTROL);
Host_reset_pipe(P_CONTROL);
status = CONTROL_TIMEOUT;
goto host_transfer_control_end;
}
#endif
}
Host_reset_pipe_fifo_access(P_CONTROL);
c = Host_get_pipe_size(P_CONTROL) - Host_byte_count(P_CONTROL);
data_length = host_read_p_rxpacket(P_CONTROL, data_pointer, data_length, &data_pointer);
if (usb_request.incomplete_read || c) data_length = 0;
Host_freeze_pipe(P_CONTROL);
Host_ack_control_in_received_free();
// In low-speed mode, the USB IP may have not yet sent the ACK at this
// point. The USB IP does not support a new start of transaction request
// from the firmware if the ACK has not been sent. The only means of
// making sure the ACK has been sent is to wait for the next Keep-Alive
// before starting a new transaction.
if (Is_usb_low_speed_mode())
{
Usb_ack_event(EVT_HOST_SOF);
if ((sav_glob_int_en = cpu_irq_is_enabled())) cpu_irq_disable();
Host_ack_sof();
(void)Is_host_sof_interrupt_enabled();
if (sav_glob_int_en) cpu_irq_enable();
while (!Is_usb_event(EVT_HOST_SOF)) // Wait for next Keep-Alive
{
if (Is_host_emergency_exit())
{
Host_freeze_pipe(P_CONTROL);
Host_reset_pipe(P_CONTROL);
status = CONTROL_TIMEOUT;
goto host_transfer_control_end;
}
}
}
} // End of IN data stage
Host_configure_pipe_token(P_CONTROL, TOKEN_OUT);
Host_ack_control_out_ready_send();
Host_unfreeze_pipe(P_CONTROL);
#if TIMEOUT_DELAY_ENABLE == ENABLE
private_sof_counter = 0; // Reset the counter in SOF detection subroutine
#endif
while (!Is_host_control_out_ready())
{
#if defined(Host_wait_action)
Host_wait_action();
#endif
if (Is_host_emergency_exit())
{
Host_freeze_pipe(P_CONTROL);
Host_reset_pipe(P_CONTROL);
status = CONTROL_TIMEOUT;
goto host_transfer_control_end;
}
if (Is_host_pipe_error(P_CONTROL)) // Any error?
{
c = Host_error_status(P_CONTROL);
Host_ack_all_errors(P_CONTROL);
status = c; // Send error status
goto host_transfer_control_end;
}
if (Is_host_stall(P_CONTROL))
{
Host_ack_stall(P_CONTROL);
status = CONTROL_STALL;
goto host_transfer_control_end;
}
#if TIMEOUT_DELAY_ENABLE == ENABLE
if (2000 < host_get_timeout()) // Count 2s
{
Host_freeze_pipe(P_CONTROL);
Host_reset_pipe(P_CONTROL);
status = CONTROL_TIMEOUT;
goto host_transfer_control_end;
}
#endif
}
Host_ack_control_out_ready();
}
// OUT request management --------------------------------------------
else // Data stage OUT (bmRequestType.D7 == 0)
{
Host_configure_pipe_token(P_CONTROL, TOKEN_OUT);
Host_ack_control_out_ready();
while (data_length)
{
Host_unfreeze_pipe(P_CONTROL);
Host_reset_pipe_fifo_access(P_CONTROL);
data_length = host_write_p_txpacket(P_CONTROL, data_pointer, data_length, (const void **)&data_pointer);
Host_send_control_out();
while (!Is_host_control_out_ready())
{
#if defined(Host_wait_action)
Host_wait_action();
#endif
if (Is_host_emergency_exit())
{
Host_freeze_pipe(P_CONTROL);
Host_reset_pipe(P_CONTROL);
status = CONTROL_TIMEOUT;
goto host_transfer_control_end;
}
if (Is_host_pipe_error(P_CONTROL)) // Any error?
{
c = Host_error_status(P_CONTROL);
Host_ack_all_errors(P_CONTROL);
status = c; // Send error status
goto host_transfer_control_end;
}
if (Is_host_stall(P_CONTROL))
{
Host_ack_stall(P_CONTROL);
status = CONTROL_STALL;
goto host_transfer_control_end;
}
}
Host_ack_control_out_ready();
} // End of OUT data stage
Host_freeze_pipe(P_CONTROL);
Host_configure_pipe_token(P_CONTROL, TOKEN_IN);
Host_ack_control_in_received_free();
Host_unfreeze_pipe(P_CONTROL);
#if TIMEOUT_DELAY_ENABLE == ENABLE
private_sof_counter = 0; // Reset the counter in SOF detection subroutine
#endif
while (!Is_host_control_in_received())
{
#if defined(Host_wait_action)
Host_wait_action();
#endif
if (Is_host_emergency_exit())
{
Host_freeze_pipe(P_CONTROL);
Host_reset_pipe(P_CONTROL);
status = CONTROL_TIMEOUT;
goto host_transfer_control_end;
}
if (Is_host_pipe_error(P_CONTROL)) // Any error?
{
c = Host_error_status(P_CONTROL);
Host_ack_all_errors(P_CONTROL);
status = c; // Send error status
goto host_transfer_control_end;
}
if (Is_host_stall(P_CONTROL))
{
Host_ack_stall(P_CONTROL);
status = CONTROL_STALL;
goto host_transfer_control_end;
}
#if TIMEOUT_DELAY_ENABLE == ENABLE
if (2000 < host_get_timeout()) // Count 2s
{
Host_freeze_pipe(P_CONTROL);
Host_reset_pipe(P_CONTROL);
status = CONTROL_TIMEOUT;
goto host_transfer_control_end;
}
#endif
}
Host_ack_control_in_received();
Host_freeze_pipe(P_CONTROL);
Host_free_control_in();
}
host_transfer_control_end:
if (!sav_int_sof_enable) // Restore SOF interrupt enable
{
if ((sav_glob_int_en = cpu_irq_is_enabled())) cpu_irq_disable();
Host_disable_sof_interrupt();
(void)Is_host_sof_interrupt_enabled();
if (sav_glob_int_en) cpu_irq_enable();
}
return status;
}
//!
//! @brief This function receives nb_data bytes pointed to by ptr_buf on the specified pipe.
//!
//! *nb_data is updated with the final number of data bytes received.
//!
//! @note This function activates the host SOF interrupt to detect time-outs.
//! The initial enable state of this interrupt will be restored.
//!
//! @param pipe
//! @param nb_data
//! @param ptr_buf
//!
//! @return Status_t: Pipe status
//!
Status_t host_get_data(uint8_t pipe, uint16_t *nb_data, void *ptr_buf)
{
Status_t status = PIPE_GOOD; // Frame correctly received by default
bool sav_int_sof_enable;
bool sav_glob_int_en;
uint8_t nak_timeout;
uint16_t n, i;
#if NAK_TIMEOUT_ENABLE == ENABLE
uint16_t cpt_nak;
#endif
n = *nb_data;
sav_int_sof_enable = Is_host_sof_interrupt_enabled();
Host_enable_sof_interrupt();
Host_enable_continuous_in_mode(pipe);
Host_configure_pipe_token(pipe, TOKEN_IN);
Host_ack_in_received(pipe);
while (n) // While missing data...
{
Host_free_in(pipe);
Host_unfreeze_pipe(pipe);
private_sof_counter = 0; // Reset the counter in SOF detection subroutine
nak_timeout = 0;
#if NAK_TIMEOUT_ENABLE == ENABLE
cpt_nak = 0;
#endif
while (!Is_host_in_received(pipe))
{
if (Is_host_emergency_exit()) // Asynchronous disconnection or role exchange detected under interrupt
{
status = PIPE_DELAY_TIMEOUT;
Host_reset_pipe(pipe);
goto host_get_data_end;
}
#if TIMEOUT_DELAY_ENABLE == ENABLE
if (private_sof_counter >= 250) // Time-out management
{
private_sof_counter = 0; // Done in host SOF interrupt
if (nak_timeout++ >= TIMEOUT_DELAY) // Check for local time-out
{
status = PIPE_DELAY_TIMEOUT;
Host_reset_pipe(pipe);
goto host_get_data_end;
}
}
#endif
if (Is_host_pipe_error(pipe)) // Error management
{
status = Host_error_status(pipe);
Host_ack_all_errors(pipe);
goto host_get_data_end;
}
if (Is_host_stall(pipe)) // STALL management
{
status = PIPE_STALL;
Host_reset_pipe(pipe);
Host_ack_stall(pipe);
goto host_get_data_end;
}
#if NAK_TIMEOUT_ENABLE == ENABLE
if (Is_host_nak_received(pipe)) // NAK received
{
Host_ack_nak_received(pipe);
if (cpt_nak++ > NAK_RECEIVE_TIMEOUT)
{
status = PIPE_NAK_TIMEOUT;
Host_reset_pipe(pipe);
goto host_get_data_end;
}
}
#endif
}
Host_freeze_pipe(pipe);
Host_reset_pipe_fifo_access(pipe);
i = Host_get_pipe_size(pipe) - Host_byte_count(pipe);
if (!ptr_buf)
{
if (Host_byte_count(pipe) > n) // More bytes received than expected
{
n = 0;
//! @todo Error code management
}
else // Nb bytes received <= expected
{
n -= Host_byte_count(pipe);
if (i) // Short packet
{
*nb_data -= n;
n = 0;
}
}
}
else
{
n = host_read_p_rxpacket(pipe, ptr_buf, n, &ptr_buf);
if (Host_byte_count(pipe)) // More bytes received than expected
{
//! @todo Error code management
}
else if (i) // Short packet with nb bytes received <= expected
{
*nb_data -= n;
n = 0;
}
}
Host_ack_in_received(pipe);
// In low-speed mode, the USB IP may have not yet sent the ACK at this
// point. The USB IP does not support a new start of transaction request
// from the firmware if the ACK has not been sent. The only means of making
// sure the ACK has been sent is to wait for the next Keep-Alive before
// starting a new transaction.
if (Is_usb_low_speed_mode())
{
Usb_ack_event(EVT_HOST_SOF);
sav_int_sof_enable = Is_host_sof_interrupt_enabled();
if ((sav_glob_int_en = cpu_irq_is_enabled())) cpu_irq_disable();
Host_ack_sof();
(void)Is_host_sof_interrupt_enabled();
if (sav_glob_int_en) cpu_irq_enable();
Host_enable_sof_interrupt();
while (!Is_usb_event(EVT_HOST_SOF)) // Wait for next Keep-Alive
{
if (Is_host_emergency_exit())
{
status = PIPE_DELAY_TIMEOUT;
Host_reset_pipe(pipe);
goto host_get_data_end;
}
}
if (!sav_int_sof_enable) // Restore SOF interrupt enable
{
if ((sav_glob_int_en = cpu_irq_is_enabled())) cpu_irq_disable();
Host_disable_sof_interrupt();
(void)Is_host_sof_interrupt_enabled();
if (sav_glob_int_en) cpu_irq_enable();
}
}
}
host_get_data_end:
Host_freeze_pipe(pipe);
// Restore SOF interrupt enable state
if (!sav_int_sof_enable)
{
if ((sav_glob_int_en = cpu_irq_is_enabled())) cpu_irq_disable();
Host_disable_sof_interrupt();
(void)Is_host_sof_interrupt_enabled();
if (sav_glob_int_en) cpu_irq_enable();
}
// And return...
return status;
}
//!
//! @brief This function sends nb_data bytes pointed to by ptr_buf on the specified pipe.
//!
//! @note This function activates the host SOF interrupt to detect time-outs.
//! The initial enable state of this interrupt will be restored.
//!
//! @param pipe
//! @param nb_data
//! @param ptr_buf
//!
//! @return Status_t: Pipe status
//!
Status_t host_send_data(uint8_t pipe, uint16_t nb_data, const void *ptr_buf)
{
Status_t status = PIPE_GOOD; // Frame correctly sent by default
bool sav_int_sof_enable;
bool sav_glob_int_en;
uint8_t nak_timeout;
#if NAK_TIMEOUT_ENABLE == ENABLE
uint16_t cpt_nak;
#endif
sav_int_sof_enable = Is_host_sof_interrupt_enabled(); // Save state of enable SOF interrupt
Host_enable_sof_interrupt();
Host_configure_pipe_token(pipe, TOKEN_OUT);
Host_ack_out_ready(pipe);
Host_unfreeze_pipe(pipe);
while (nb_data) // While there is something to send...
{
// Prepare data to be sent
Host_reset_pipe_fifo_access(pipe);
nb_data = host_write_p_txpacket(pipe, ptr_buf, nb_data, &ptr_buf);
private_sof_counter = 0; // Reset the counter in SOF detection subroutine
#if NAK_TIMEOUT_ENABLE == ENABLE
cpt_nak = 0;
#endif
nak_timeout = 0;
Host_ack_out_ready_send(pipe);
while (!Is_host_out_ready(pipe))
{
if (Is_host_emergency_exit()) // Async disconnection or role change detected under interrupt
{
status = PIPE_DELAY_TIMEOUT;
Host_reset_pipe(pipe);
goto host_send_data_end;
}
#if TIMEOUT_DELAY_ENABLE == ENABLE
if (private_sof_counter >= 250) // Count 250 ms (250 SOF)
{
private_sof_counter = 0;
if (nak_timeout++ >= TIMEOUT_DELAY) // Increment time-out and check for overflow
{
status = PIPE_DELAY_TIMEOUT;
Host_reset_pipe(pipe);
goto host_send_data_end;
}
}
#endif
if (Is_host_pipe_error(pipe)) // Error management
{
status = Host_error_status(pipe);
Host_ack_all_errors(pipe);
goto host_send_data_end;
}
if (Is_host_stall(pipe)) // STALL management
{
status = PIPE_STALL;
Host_ack_stall(pipe);
goto host_send_data_end;
}
#if NAK_TIMEOUT_ENABLE == ENABLE
if (Is_host_nak_received(pipe)) // NAK received
{
Host_ack_nak_received(pipe);
if (cpt_nak++ > NAK_SEND_TIMEOUT)
{
status = PIPE_NAK_TIMEOUT;
Host_reset_pipe(pipe);
goto host_send_data_end;
}
}
#endif
}
// Here OUT sent
Host_ack_out_ready(pipe);
}
while (Host_nb_busy_bank(pipe));
host_send_data_end:
Host_freeze_pipe(pipe);
// Restore SOF interrupt enable state
if (!sav_int_sof_enable)
{
if ((sav_glob_int_en = cpu_irq_is_enabled())) cpu_irq_disable();
Host_disable_sof_interrupt();
(void)Is_host_sof_interrupt_enabled();
if (sav_glob_int_en) cpu_irq_enable();
}
// And return...
return status;
}
void usb_host_task(void)
#endif
{
#define DEVICE_DEFAULT_MAX_ERROR_COUNT 2
static uint8_t device_default_error_count;
#ifdef HOST_VBUS_LOW_TIMEOUT
extern t_cpu_time timer_vbus_low;
#endif
static bool sav_int_sof_enable;
uint8_t pipe;
#ifdef FREERTOS_USED
portTickType xLastWakeTime;
xLastWakeTime = xTaskGetTickCount();
while (true)
{
vTaskDelayUntil(&xLastWakeTime, configTSK_USB_HST_PERIOD);
#endif // FREERTOS_USED
switch (device_state)
{
#ifdef HOST_VBUS_LOW_TIMEOUT
case DEVICE_VBUS_LOW:
Usb_disable_vbus();
if (cpu_is_timeout(&timer_vbus_low))
usb_host_task_init();
break;
#endif
//------------------------------------------------------
// DEVICE_UNATTACHED state
//
// - Default init state
// - Try to give device power supply
//
case DEVICE_UNATTACHED:
device_default_error_count = 0;
nb_interface_supported = 0;
Host_clear_device_status(); // Reset device status
Usb_clear_all_event(); // Clear all software events
Host_disable_sof();
host_disable_all_pipes();
Usb_enable_vbus(); // Give at least device power supply!
// If VBus OK, wait for device connection
if (Is_usb_vbus_high())
device_state = DEVICE_ATTACHED;
break;
//------------------------------------------------------
// DEVICE_ATTACHED state
//
// - VBus is on
// - Try to detect device connection
//
case DEVICE_ATTACHED:
if (Is_host_device_connection() || Is_usb_event(EVT_HOST_CONNECTION) ) // Device pull-up detected
{
device_attached_retry:
if( Is_usb_event(EVT_HOST_CONNECTION) ) {
Usb_ack_event(EVT_HOST_CONNECTION);
}
Usb_ack_bconnection_error_interrupt();
Usb_ack_vbus_error_interrupt();
Host_ack_device_connection();
Host_clear_device_status(); // Reset device status
cpu_irq_disable();
Host_disable_device_disconnection_interrupt();
Host_send_reset(); // First USB reset
(void)Is_host_sending_reset();
cpu_irq_enable();
Usb_ack_event(EVT_HOST_SOF);
// Active wait for end of reset send
while (Is_host_sending_reset())
{
// The USB macro does not signal the end of reset when a disconnection occurs
if (Is_host_device_disconnection())
{
// Stop sending USB reset
Host_stop_sending_reset();
}
}
Host_ack_reset_sent();
Host_enable_sof(); // Start SOF generation
Host_enable_sof_interrupt(); // SOF will be detected under interrupt
if (!Is_host_device_disconnection())
{
// Workaround for some buggy devices with powerless pull-up
// usually low-speed where data line rises slowly and can be interpreted as disconnection
for (sof_cnt = 0; sof_cnt < 0xFFFF; sof_cnt++) // Basic time-out counter
{
// If we detect SOF, device is still alive and connected, just clear false disconnect flag
if (Is_usb_event(EVT_HOST_SOF) && Is_host_device_disconnection())
{
Host_ack_device_connection();
Host_ack_device_disconnection();
break;
}
}
}
Host_enable_device_disconnection_interrupt();
sof_cnt = 0;
while (sof_cnt < 100) // Wait 100 ms after USB reset
{
if (Is_usb_event(EVT_HOST_SOF)) Usb_ack_event(EVT_HOST_SOF), sof_cnt++; // Count SOFs
if (Is_host_emergency_exit() || Is_usb_bconnection_error_interrupt()) goto device_attached_error;
}
device_state = DEVICE_POWERED;
LOG_STR(log_device_connected);
Host_device_connection_action();
sof_cnt = 0;
}
device_attached_error:
// Device connection error, or VBus pb -> Retry the connection process from the beginning
if (Is_usb_bconnection_error_interrupt() || Is_usb_vbus_error_interrupt() || Is_usb_vbus_low())
{
if (device_state != DEVICE_VBUS_LOW)
device_state = DEVICE_UNATTACHED;
Usb_ack_bconnection_error_interrupt();
Usb_ack_vbus_error_interrupt();
Host_disable_sof();
}
break;
//------------------------------------------------------
// DEVICE_POWERED state
//
// - Device connection (attach) has been detected,
// - Wait 100 ms and configure default control pipe
//
case DEVICE_POWERED:
if (Is_usb_event(EVT_HOST_SOF))
{
Usb_ack_event(EVT_HOST_SOF);
if (sof_cnt++ >= 100) // Wait 100 ms
{
Host_enable_pipe(P_CONTROL);
(void)Host_configure_pipe(P_CONTROL,
0,
EP_CONTROL,
TYPE_CONTROL,
TOKEN_SETUP,
8,
SINGLE_BANK);
device_state = DEVICE_DEFAULT;
}
}
break;
//------------------------------------------------------
// DEVICE_DEFAULT state
//
// - Get device descriptor
// - Reconfigure control pipe according to device control endpoint
// - Assign device address
//
case DEVICE_DEFAULT:
// Get first device descriptor
if (host_get_device_descriptor_incomplete() == CONTROL_GOOD)
{
sof_cnt = 0;
while (sof_cnt < 20) // Wait 20 ms before USB reset (special buggy devices...)
{
if (Is_usb_event(EVT_HOST_SOF)) Usb_ack_event(EVT_HOST_SOF), sof_cnt++;
if (Is_host_emergency_exit() || Is_usb_bconnection_error_interrupt()) break;
}
cpu_irq_disable();
Host_disable_device_disconnection_interrupt();
Host_send_reset(); // First USB reset
(void)Is_host_sending_reset();
cpu_irq_enable();
Usb_ack_event(EVT_HOST_SOF);
// Active wait for end of reset send
while (Is_host_sending_reset())
{
// The USB macro does not signal the end of reset when a disconnection occurs
if (Is_host_device_disconnection())
{
// Stop sending USB reset
Host_stop_sending_reset();
}
}
Host_ack_reset_sent();
if (!Is_host_device_disconnection())
{
// Workaround for some buggy devices with powerless pull-up
// usually low-speed where data line rises slowly and can be interpreted as disconnection
for (sof_cnt = 0; sof_cnt < 0xFFFF; sof_cnt++) // Basic time-out counter
{
// If we detect SOF, device is still alive and connected, just clear false disconnect flag
if (Is_usb_event(EVT_HOST_SOF) && Is_host_device_disconnection())
{
Host_ack_device_connection();
Host_ack_device_disconnection();
break;
}
}
}
Host_enable_device_disconnection_interrupt();
sof_cnt = 0;
while (sof_cnt < 200) // Wait 200 ms after USB reset
{
if (Is_usb_event(EVT_HOST_SOF)) Usb_ack_event(EVT_HOST_SOF), sof_cnt++;
if (Is_host_emergency_exit() || Is_usb_bconnection_error_interrupt()) break;
}
Host_disable_pipe(P_CONTROL);
Host_unallocate_memory(P_CONTROL);
Host_enable_pipe(P_CONTROL);
// Reconfigure the control pipe according to the device control endpoint
(void)Host_configure_pipe(P_CONTROL,
0,
EP_CONTROL,
TYPE_CONTROL,
TOKEN_SETUP,
data_stage[OFFSET_FIELD_MAXPACKETSIZE],
SINGLE_BANK);
// Give an absolute device address
if (host_set_address(DEVICE_ADDRESS) == CONTROL_GOOD)
{
for (pipe = 0; pipe < MAX_PEP_NB; pipe++)
Host_configure_address(pipe, DEVICE_ADDRESS);
device_state = DEVICE_ADDRESSED;
}
else if (device_state != DEVICE_VBUS_LOW)
device_state = DEVICE_ERROR;
}
else
{
if (device_state != DEVICE_VBUS_LOW)
{
if (++device_default_error_count > DEVICE_DEFAULT_MAX_ERROR_COUNT)
device_state = DEVICE_ERROR;
else
{
Host_disable_sof();
Host_disable_pipe(P_CONTROL);
Host_unallocate_memory(P_CONTROL);
device_state = DEVICE_ATTACHED;
goto device_attached_retry;
}
}
Usb_ack_bconnection_error_interrupt();
Usb_ack_vbus_error_interrupt();
Host_disable_sof();
}
break;
//------------------------------------------------------
// DEVICE_ADDRESSED state
//
// - Check if VID PID is in supported list
//
case DEVICE_ADDRESSED:
if (host_get_device_descriptor() == CONTROL_GOOD)
{
// Detect if the device connected belongs to the supported devices table
if (host_check_VID_PID())
{
Host_set_device_supported();
Host_device_supported_action();
device_state = DEVICE_CONFIGURED;
}
else
{
#if HOST_STRICT_VID_PID_TABLE == ENABLE
device_state = DEVICE_ERROR;
LOG_STR(log_unsupported_device);
#else
device_state = DEVICE_CONFIGURED;
#endif
Host_device_not_supported_action();
}
}
else if (device_state != DEVICE_VBUS_LOW)
device_state = DEVICE_ERROR; // Can not get device descriptor
break;
//------------------------------------------------------
// DEVICE_CONFIGURED state
//
// - Configure pipes for the supported interface
// - Send Set_configuration() request
// - Go to full operating mode (device ready)
//
case DEVICE_CONFIGURED:
{
uint8_t configuration_index = 0;
if (host_get_configuration_descriptor(configuration_index) == CONTROL_GOOD)
{
if (host_check_class()) // Class support OK?
{
#if HOST_AUTO_CFG_ENDPOINT == DISABLE
User_configure_endpoint(); // User call here instead of autoconfig
Host_set_configured(); // Assumes config is OK with user config
#endif
if (Is_host_configured())
{
if (host_set_configuration(data_stage[OFFSET_FIELD_CONFIGURATION_NB]) == CONTROL_GOOD) // Send Set_configuration
{
// Device and host are now fully configured
// go to DEVICE_READY normal operation
device_state = DEVICE_READY;
// Monitor device disconnection under interrupt
Host_enable_device_disconnection_interrupt();
// If user host application requires SOF interrupt event
// Keep SOF interrupt enabled, otherwise disable this interrupt
#if HOST_CONTINUOUS_SOF_INTERRUPT == DISABLE
cpu_irq_disable();
Host_disable_sof_interrupt();
(void)Is_host_sof_interrupt_enabled();
cpu_irq_enable();
#endif
Host_new_device_connection_action();
cpu_irq_enable();
LOG_STR(log_device_enumerated);
}
else if (device_state != DEVICE_VBUS_LOW)
device_state = DEVICE_ERROR; // Problem during Set_configuration request...
}
}
else // Device class not supported...
{
device_state = DEVICE_UNSUPPORTED;
LOG_STR(log_unsupported_device);
Host_device_class_not_supported_action();
}
}
else if (device_state != DEVICE_VBUS_LOW)
device_state = DEVICE_ERROR; // Can not get configuration descriptors...
}
break;
//------------------------------------------------------
// DEVICE_READY state
//
// - Full standard operating mode
// - Nothing to do...
//
case DEVICE_READY: // Host full standard operating mode!
break;
//------------------------------------------------------
// DEVICE_UNSUPPORTED state
//
case DEVICE_UNSUPPORTED:
break;
//------------------------------------------------------
// DEVICE_ERROR state
//
// - Error state
// - Do custom action call (probably go to default mode...)
//
case DEVICE_ERROR: //! @todo
#if HOST_ERROR_RESTART == ENABLE
device_state = DEVICE_UNATTACHED;
#endif
Host_device_error_action();
break;
//------------------------------------------------------
// DEVICE_SUSPENDED state
//
// - Host application request to suspend the device activity
// - State machine comes here thanks to Host_request_suspend()
//
case DEVICE_SUSPENDED:
if (Is_device_supports_remote_wakeup()) // If the connected device supports remote wake-up
{
host_set_feature_remote_wakeup(); // Enable this feature...
}
LOG_STR(log_usb_suspended);
sav_int_sof_enable = Is_host_sof_interrupt_enabled(); //Save current SOF interrupt enable state
cpu_irq_disable();
Host_disable_sof_interrupt();
(void)Is_host_sof_interrupt_enabled();
cpu_irq_enable();
Host_ack_sof();
Host_disable_sof(); // Stop SOF generation, this generates the suspend state
Host_ack_hwup();
Host_enable_hwup_interrupt(); // Enable host wake-up interrupt
// (this is the unique USB interrupt able to wake up the CPU core from power-down mode)
(void)Is_host_hwup_interrupt_enabled(); // Make sure host wake-up interrupt is enabled
Usb_freeze_clock();
//! @todo Implement this on the silicon version
//Stop_pll();
Host_suspend_action(); // Custom action here! (e.g. go to power-save mode...)
device_state = DEVICE_WAIT_RESUME; // Wait for device resume event
break;
//------------------------------------------------------
// DEVICE_WAIT_RESUME state
//
// Wait in this state till:
// - the host receives an upstream resume from the device
// - or the host software request the device to resume
//
case DEVICE_WAIT_RESUME:
if (Is_usb_event(EVT_HOST_HWUP) || Is_host_request_resume()) // Remote wake-up has been detected
// or local resume request has been received
{
if (Is_host_request_resume()) // Not a remote wake-up, but a host application request
{
// CAUTION: HWUP can be cleared only when USB clock is active
//! @todo Implement this on the silicon version
//Pll_start_auto(); // First Restart the PLL for USB operation
//Wait_pll_ready(); // Make sure PLL is locked
Usb_unfreeze_clock(); // Enable clock on USB interface
(void)Is_usb_clock_frozen(); // Make sure USB interface clock is enabled
cpu_irq_disable();
Host_disable_hwup_interrupt(); // Wake-up interrupt should be disabled as host is now awoken!
(void)Is_host_hwup_interrupt_enabled();
cpu_irq_enable();
Host_ack_hwup(); // Clear HWUP interrupt flag
}
Host_enable_sof();
Host_send_resume(); // Send downstream resume
while (!Is_host_down_stream_resume()); // Wait for downstream resume sent
Host_ack_remote_wakeup(); // Ack remote wake-up reception
Host_ack_request_resume(); // Ack software request
Host_ack_down_stream_resume(); // Ack downstream resume sent
Usb_ack_event(EVT_HOST_HWUP); // Ack software event
if (sav_int_sof_enable) Host_enable_sof_interrupt(); // Restore SOF interrupt enable state before suspend
device_state = DEVICE_READY; // Come back to full operating mode
LOG_STR(log_usb_resumed);
}
break;
//------------------------------------------------------
// default state
//
// - Default case: ERROR
// - Go to DEVICE_UNATTACHED state
//
default:
device_state = DEVICE_UNATTACHED;
break;
}
#ifdef FREERTOS_USED
}
#endif
}
/**
* @brief This function receives nb_data pointed with *buf with the pipe number specified
*
* The nb_data parameter is passed as a U16 pointer, thus the data pointed by this pointer
* is updated with the final number of data byte received.
*
* @param pipe
* @param nb_data
* @param buf
*
* @return status
*/
U8 host_get_data(U8 pipe, U16 *nb_data, U8 *buf)
{
U8 status=PIPE_GOOD;
U8 sav_int_sof_enable;
U8 nak_timeout;
U16 n,i;
U16 cpt_nak;
#if (USER_PERIODIC_PIPE==ENABLE)
freeze_user_periodic_pipe();
#endif
n=*nb_data;
*nb_data=0;
sav_int_sof_enable=Is_host_sof_interrupt_enabled();
Host_enable_sof_interrupt();
Host_select_pipe(pipe);
Host_continuous_in_mode();
Host_set_token_in();
Host_ack_in_received();
while (n) // While missing data...
{
Host_unfreeze_pipe();
Host_send_in();
private_sof_counter=0; // Reset the counter in SOF detection sub-routine
nak_timeout=0;
cpt_nak=0;
while (!Is_host_in_received())
{
if (Is_host_emergency_exit()) // Async disconnection or role change detected under interrupt
{
status=PIPE_DELAY_TIMEOUT;
Host_reset_pipe(pipe);
goto host_get_data_end;
}
#if (TIMEOUT_DELAY_ENABLE==ENABLE)
if (private_sof_counter>=250) // Timeout management
{
private_sof_counter=0; // Done in host SOF interrupt
if (nak_timeout++>=TIMEOUT_DELAY)// Check for local timeout
{
status=PIPE_DELAY_TIMEOUT;
Host_reset_pipe(pipe);
goto host_get_data_end;
}
}
#endif
if(Is_host_pipe_error()) // Error management
{
status = Host_error_status();
Host_ack_all_errors();
goto host_get_data_end;
}
if(Is_host_stall()) // STALL management
{
if( Is_host_in_received() )
break;
status =PIPE_STALL;
Host_reset_pipe(pipe);
Host_ack_stall();
goto host_get_data_end;
}
#if (NAK_TIMEOUT_ENABLE==ENABLE)
if(Is_host_nak_received()) //NAK received
{
Host_ack_nak_received();
if (cpt_nak++>NAK_RECEIVE_TIMEOUT)
{
status = PIPE_NAK_TIMEOUT;
Host_reset_pipe(pipe);
goto host_get_data_end;
}
}
#endif
}
status=PIPE_GOOD;
Host_freeze_pipe();
if (Host_byte_counter()<=n)
{
if ((Host_byte_counter() < n)&&(Host_byte_counter()<Host_get_pipe_length()))
{ n=0;}
else
{ n-=Host_byte_counter();}
(*nb_data)+=Host_byte_counter(); // Update nb of byte received
if( NULL != buf )
{
for (i=Host_byte_counter();i;i--)
{ *buf=Host_read_byte(); buf++;}
}
}
else // more bytes received than expected
{ // TODO error code management
*nb_data+=n;
if( NULL != buf )
{
for (i=n;i;i--) // Byte number limited to the initial request (limit tab over pb)
{ *buf=Host_read_byte(); buf++; }
}
n=0;
}
Host_ack_in_received();
}
Host_freeze_pipe();
host_get_data_end:
if (sav_int_sof_enable==FALSE)
{
Host_disable_sof_interrupt();
}
#if (USER_PERIODIC_PIPE==ENABLE)
unfreeze_user_periodic_pipe();
#endif
return ((U8)status);
}
/**
* @brief This function send nb_data pointed with *buf with the pipe number specified
*
* @note This function will activate the host sof interrupt to detect timeout. The
* interrupt enable sof will be restore.
*
* @param pipe
* @param nb_data
* @param buf
*
* @return status
*/
U8 host_send_data(U8 pipe, U16 nb_data, U8 *buf)
{
U8 c;
U8 status=PIPE_GOOD;
U8 sav_int_sof_enable;
U8 nak_timeout;
U16 cpt_nak;
U8 nb_data_loaded;
U8 cpt_err_timeout=0;
#if (USER_PERIODIC_PIPE==ENABLE)
freeze_user_periodic_pipe();
#endif
sav_int_sof_enable=Is_host_sof_interrupt_enabled(); // Save state of enable sof interrupt
Host_enable_sof_interrupt();
Host_select_pipe(pipe);
Host_set_token_out();
Host_ack_out_sent();
Host_unfreeze_pipe();
while (nb_data != 0) // While there is something to send...
{
// Prepare data to be sent
c = Host_get_pipe_length();
if ( (U16)c > nb_data)
{
nb_data_loaded = (U8)nb_data;
c = nb_data;
}
else
{ nb_data_loaded = c; }
while (c!=0) // Load Pipe buffer
{
Host_write_byte(*buf++);
c--;
}
private_sof_counter=0; // Reset the counter in SOF detection sub-routine
cpt_nak=0;
nak_timeout=0;
Host_ack_out_sent();
Host_send_out();
while (!Is_host_out_sent())
{
if (Is_host_emergency_exit())// Async disconnection or role change detected under interrupt
{
status=PIPE_DELAY_TIMEOUT;
Host_reset_pipe(pipe);
goto host_send_data_end;
}
#if (TIMEOUT_DELAY_ENABLE==ENABLE)
if (private_sof_counter>=250) // Count 250ms (250sof)
{
private_sof_counter=0;
if (nak_timeout++>=TIMEOUT_DELAY) // Inc timeout and check for overflow
{
status=PIPE_DELAY_TIMEOUT;
Host_reset_pipe(pipe);
goto host_send_data_end;
}
}
#endif
if (Is_host_pipe_error()) // Any error ?
{
status = Host_error_status();
Host_ack_all_errors();
if(status == PIPE_TIMEOUT)
{
if(cpt_err_timeout++>100)
{
goto host_send_data_end;
}
else
{
c=0;
while(c<2) // wait 2 ms
{
if (Is_usb_event(EVT_HOST_SOF)) { Usb_ack_event(EVT_HOST_SOF); c++; }
if (Is_host_emergency_exit() ) {break;}
}
Host_unfreeze_pipe();
}
}
}
if (Is_host_stall()) // Stall management
{
status =PIPE_STALL;
Host_ack_stall();
goto host_send_data_end;
}
#if (NAK_TIMEOUT_ENABLE==ENABLE)
if(Is_host_nak_received()) //NAK received
{
Host_ack_nak_received();
if (cpt_nak++>NAK_SEND_TIMEOUT)
{
status = PIPE_NAK_TIMEOUT;
Host_reset_pipe(pipe);
goto host_send_data_end;
}
}
#endif
}
// Here OUT sent
nb_data -= nb_data_loaded;
status=PIPE_GOOD; // Frame correctly sent
Host_ack_out_sent();
}
while(0!=Host_number_of_busy_bank());
host_send_data_end:
Host_freeze_pipe();
// Restore sof interrupt enable state
if (sav_int_sof_enable==FALSE) {Host_disable_sof_interrupt();}
#if (USER_PERIODIC_PIPE==ENABLE)
unfreeze_user_periodic_pipe();
#endif
// And return...
return ((U8)status);
}
/**
* @brief Entry point of the USB host management
*
* The aim is to manage the device target connection and enumeration
* depending on the device_state, the function performs the required operations
* to get the device enumerated and configured
* Once the device is operationnal, the device_state value is DEVICE_READY
* This state should be tested by the host task application before performing
* any applicative requests to the device.
*
* @param none
*
* @return none
*
* \image html host_task.gif
*/
void usb_host_task(void)
{
switch (device_state)
{
//------------------------------------------------------
// DEVICE_UNATTACHED state
//
// - Default init state
// - Try to give device power supply
//
case DEVICE_UNATTACHED:
Host_clear_device_supported(); // Reset Device status
Host_clear_configured();
Host_clear_device_ready();
Usb_clear_all_event(); // Clear all software events
new_device_connected=FALSE;
selected_device=0;
#if (USB_HUB_SUPPORT==ENABLE)
nb_hub_present = 0;
#endif
#if (SOFTWARE_VBUS_CTRL==ENABLE)
if( Is_usb_bconnection_error_interrupt()||Is_usb_vbus_error_interrupt())
{
Usb_ack_bconnection_error_interrupt();
Usb_ack_vbus_error_interrupt();
Host_clear_vbus_request();
}
Usb_disable_vbus_pad();
Usb_enable_manual_vbus();
if(Is_usb_srp_interrupt())
{
Usb_ack_srp_interrupt();
Usb_enable_vbus_pad();
Usb_enable_vbus();
device_state=DEVICE_ATTACHED;
}
#else
Usb_enable_vbus(); // Give at least device power supply!!!
if(Is_usb_vbus_high())
{ device_state=DEVICE_ATTACHED; } // If VBUS ok goto to device connection expectation
#endif
break;
//------------------------------------------------------
// DEVICE_ATTACHED state
//
// - Vbus is on
// - Try to detected device connection
//
case DEVICE_ATTACHED :
if (Is_device_connection() || (force_enumeration==TRUE)) // Device pull-up detected
{
Host_ack_device_connection();
Host_clear_device_supported(); // Reset Device status
Host_clear_configured();
Host_clear_device_ready();
Usb_clear_all_event(); // Clear all software events
new_device_connected=FALSE;
force_enumeration=FALSE;
// Now device is connected, enable disconnection interrupt
Host_enable_device_disconnection_interrupt();
Enable_interrupt();
// Reset device status
Host_clear_device_supported();
Host_clear_configured();
Host_clear_device_ready();
Host_enable_sof(); // Start Start Of Frame generation
Host_enable_sof_interrupt(); // SOF will be detected under interrupt
c = 0;
while (c<100) // wait 100ms before USB reset
{
if (Is_usb_event(EVT_HOST_SOF)) { Usb_ack_event(EVT_HOST_SOF); c++; }// Count Start Of frame
if (Is_host_emergency_exit() || Is_usb_bconnection_error_interrupt()) {goto device_attached_error;}
}
Host_disable_device_disconnection_interrupt();
Host_send_reset(); // First USB reset
Usb_ack_event(EVT_HOST_SOF);
while (Is_host_reset()); // Active wait of end of reset send
Host_ack_reset();
//Workaround for some bugly devices with powerless pull up
//usually low speed where data line rise slowly and can be interpretaded as disconnection
for(c=0;c!=0xFFFF;c++) // Basic Timeout counter
{
if(Is_usb_event(EVT_HOST_SOF)) //If we detect SOF, device is still alive and connected, just clear false disconnect flag
{
if(Is_device_disconnection())
{
Host_ack_device_connection();
Host_ack_device_disconnection();
break;
}
}
}
Host_enable_device_disconnection_interrupt();
// All USB pipes must be reconfigured after a USB reset generation
host_configure_pipe(PIPE_CONTROL, \
TYPE_CONTROL, \
TOKEN_SETUP, \
EP_CONTROL, \
SIZE_64, \
ONE_BANK, \
0 );
c = 0;
while (c<100) // wait 100ms after USB reset
{
if (Is_usb_event(EVT_HOST_SOF)) { Usb_ack_event(EVT_HOST_SOF); c++; }// Count Start Of frame
if (Is_host_emergency_exit() || Is_usb_bconnection_error_interrupt()) {goto device_attached_error;}
}
device_state = DEVICE_POWERED;
c=0;
}
device_attached_error:
// Device connection error, or vbus pb -> Retry the connection process from the begining
if( Is_usb_bconnection_error_interrupt()||Is_usb_vbus_error_interrupt()||Is_usb_vbus_low())
{
Usb_ack_bconnection_error_interrupt();
Usb_enable_vbus_hw_control();
device_state=DEVICE_UNATTACHED;
Usb_disable_vbus();
Usb_disable_vbus_pad();
Usb_enable_vbus_pad();
Usb_ack_vbus_error_interrupt();
Usb_enable_vbus();
Usb_disable_vbus_hw_control();
Host_disable_sof();
}
break;
//------------------------------------------------------
// DEVICE_POWERED state
//
// - Device connection (attach) as been detected,
// - Wait 100ms and configure default control pipe
//
case DEVICE_POWERED :
LOG_STR_CODE(log_device_connected);
Host_device_connection_action();
if (Is_usb_event(EVT_HOST_SOF))
{
Usb_ack_event(EVT_HOST_SOF);
if (c++ >= 100) // Wait 100ms
{
device_state = DEVICE_DEFAULT;
}
}
break;
//------------------------------------------------------
// DEVICE_DEFAULT state
//
// - Get device descriptor
// - Reconfigure Pipe 0 according to Device EP0
// - Attribute device address
//
case DEVICE_DEFAULT :
// Get first device descriptor
Host_select_device(0);
usb_tree.device[0].ep_ctrl_size=8;
if( CONTROL_GOOD == host_get_device_descriptor_uncomplete())
{
c = 0;
while(c<20) // wait 20ms before USB reset (special buggly devices...)
{
if (Is_usb_event(EVT_HOST_SOF)) { Usb_ack_event(EVT_HOST_SOF); c++; }
if (Is_host_emergency_exit() || Is_usb_bconnection_error_interrupt()) {break;}
}
Host_disable_device_disconnection_interrupt();
Host_send_reset(); // First USB reset
Usb_ack_event(EVT_HOST_SOF);
while (Is_host_reset()); // Active wait of end of reset send
Host_ack_reset();
//Workaround for some bugly devices with powerless pull up
//usually low speed where data line rise slowly and can be interpretaded as disconnection
for(c=0;c!=0xFFFF;c++) // Basic Timeout counter
{
if(Is_usb_event(EVT_HOST_SOF)) //If we detect SOF, device is still alive and connected, just clear false disconnect flag
{
if(Is_device_disconnection())
{
Host_ack_device_connection();
Host_ack_device_disconnection();
break;
}
}
}
Host_enable_device_disconnection_interrupt();
c = 0;
host_configure_pipe(PIPE_CONTROL, \
TYPE_CONTROL, \
TOKEN_SETUP, \
EP_CONTROL, \
SIZE_64, \
ONE_BANK, \
0 );
while(c<200) // wait 200ms after USB reset
{
if (Is_usb_event(EVT_HOST_SOF)) { Usb_ack_event(EVT_HOST_SOF); c++; }
if (Is_host_emergency_exit() || Is_usb_bconnection_error_interrupt()) {break;}
}
usb_tree.device[0].ep_ctrl_size=data_stage[OFFSET_FIELD_MAXPACKETSIZE];
// Give an absolute device address
host_set_address(DEVICE_BASE_ADDRESS);
usb_tree.device[0].device_address=DEVICE_BASE_ADDRESS;
device_state = DEVICE_ADDRESSED;
}
else
{ device_state = DEVICE_ERROR; }
break;
//------------------------------------------------------
// DEVICE_BASE_ADDRESSED state
//
// - Check if VID PID is in supported list
//
case DEVICE_ADDRESSED :
if (CONTROL_GOOD == host_get_device_descriptor())
{
// Detect if the device connected belongs to the supported devices table
if (HOST_TRUE == host_check_VID_PID())
{
Host_set_device_supported();
Host_device_supported_action();
device_state = DEVICE_CONFIGURED;
}
else
{
#if (HOST_STRICT_VID_PID_TABLE==ENABLE)
Host_device_not_supported_action();
device_state = DEVICE_ERROR;
#else
device_state = DEVICE_CONFIGURED;
#endif
}
}
else // Can not get device descriptor
{ device_state = DEVICE_ERROR; }
break;
//------------------------------------------------------
// DEVICE_CONFIGURED state
//
// - Configure pipes for the supported interface
// - Send Set_configuration() request
// - Goto full operating mode (device ready)
//
case DEVICE_CONFIGURED :
if (CONTROL_GOOD == host_get_configuration_descriptor())
{
if (HOST_FALSE != host_check_class()) // Class support OK?
{
usb_tree.nb_device++;
#if (HOST_AUTO_CFG_ENDPOINT==ENABLE)
if(host_auto_configure_endpoint())
#else
Host_set_configured(); // Assumes config is OK with user config
if(User_configure_endpoint()) // User call here instead of autoconfig
#endif
{
if (CONTROL_GOOD== host_set_configuration(1)) // Send Set_configuration
{
//host_set_interface(interface_bound,interface_bound_alt_set);
// device and host are now fully configured
// goto DEVICE READY normal operation
device_state = DEVICE_READY;
Host_set_device_ready();
// monitor device disconnection under interrupt
Host_enable_device_disconnection_interrupt();
// If user host application requires SOF interrupt event
// Keep SOF interrupt enable otherwize, disable this interrupt
#if (HOST_CONTINUOUS_SOF_INTERRUPT==DISABLE && USB_HUB_SUPPORT==DISABLE)
Host_disable_sof_interrupt();
#endif
#if (USB_HUB_SUPPORT==ENABLE)
// Check if the connected device is a hub
if(Get_class(0)==HUB_CLASS && Get_subclass(0)==0x00 && Get_protocol(0)==0x00)
{
// Get hub descriptor
if( Get_hub_descriptor()==CONTROL_GOOD)
{
// Power each port of the hub
i=data_stage[NB_PORT_OFFSET];
for(c=1;c<=i;c++)
{
Set_port_feature(PORT_POWER,c);
}
nb_hub_present = 1;
hub_device_address[0]=DEVICE_BASE_ADDRESS;
hub_init(nb_hub_present-1);
}
}
else
{
nb_hub_present = 0;
new_device_connected=TRUE;
}
#else
new_device_connected=TRUE;
#endif
Enable_interrupt();
LOG_STR_CODE(log_device_enumerated);
}
else// Problem during Set_configuration request...
{ device_state = DEVICE_ERROR; }
}
}
else // device class not supported...
{
device_state = DEVICE_ERROR;
LOG_STR_CODE(log_device_unsupported);
Host_device_class_not_supported_action();
}
}
else // Can not get configuration descriptors...
{ device_state = DEVICE_ERROR; }
break;
//------------------------------------------------------
// DEVICE_READY state
//
// - Full std operatinf mode
// - Nothing to do...
//
case DEVICE_READY: // Host full std operating mode!
new_device_connected=FALSE;
#if (USB_HUB_SUPPORT==ENABLE)
f_hub_port_disconnect=FALSE;
// If one hub is present in the USB tree and the period interval
// for the interrupt hub endpoint occurs
if(nb_hub_present && hub_interrupt_sof==0)
{
saved_device=selected_device; // Backup user selected device
for(j=1;j<=nb_hub_present;j++)
{
for(i=0;i<MAX_DEVICE_IN_USB_TREE;i++)
{
if(usb_tree.device[i].device_address==hub_device_address[j-1]) break;
}
Host_select_device(i);
Host_select_pipe(usb_tree.device[i].interface[0].ep[0].pipe_number);
Host_ack_nak_received();
Host_ack_in_received();
Host_unfreeze_pipe();
Host_send_in();
while(1)
{
if(Is_host_nak_received()) break;
if(Is_host_emergency_exit()) break;
if(Is_host_in_received()) break;
}
Host_freeze_pipe();
if(Is_host_nak_received())
{
Host_ack_nak_received();
}
if(Is_host_in_received())
{
if(Is_host_stall()==FALSE)
{
c=Host_read_byte();
}
Host_ack_in_received();
hub_manage_port_change_status(c,j);
}
} // for all hub
Host_select_device(saved_device); // Restore user selected device
#if (USER_PERIODIC_PIPE==ENABLE)
unfreeze_user_periodic_pipe();
#endif
}
#endif
break;
//------------------------------------------------------
// DEVICE_ERROR state
//
// - Error state
// - Do custom action call (probably go to default mode...)
//
case DEVICE_ERROR : // TODO !!!!
#if (HOST_ERROR_RESTART==ENABLE)
device_state=DEVICE_UNATTACHED;
#endif
Host_device_error_action();
break;
//------------------------------------------------------
// DEVICE_SUSPENDED state
//
// - Host application request to suspend the device activity
// - State machine comes here thanks to Host_request_suspend()
//
case DEVICE_SUSPENDED :
if(Is_device_supports_remote_wakeup()) // If the connected device supports remote wake up
{
host_set_feature_remote_wakeup(); // Enable this feature...
}
LOG_STR_CODE(log_going_to_suspend);
c = Is_host_sof_interrupt_enabled(); //Save current sof interrupt enable state
Host_disable_sof_interrupt();
Host_ack_sof();
Host_disable_sof(); // Stop start of frame generation, this generates the suspend state
Host_ack_hwup();
Host_enable_hwup_interrupt(); // Enable host wake-up interrupt
// (this is the unique USB interrupt able to wake up the CPU core from power-down mode)
Usb_freeze_clock();
Stop_pll();
Host_suspend_action(); // Custom action here! (for example go to power-save mode...)
device_state=DEVICE_WAIT_RESUME; // wait for device resume event
break;
//------------------------------------------------------
// DEVICE_WAIT_RESUME state
//
// - Wait in this state till the host receives an upstream resume from the device
// - or the host software request the device to resume
//
case DEVICE_WAIT_RESUME :
if(Is_usb_event(EVT_HOST_HWUP)|| Is_host_request_resume())// Remote wake up has been detected
// or Local resume request has been received
{
if(Is_host_request_resume()) // Not a remote wakeup, but an host application request
{
Host_disable_hwup_interrupt(); // Wake up interrupt should be disable host is now wake up !
// CAUTION HWUP can be cleared only when USB clock is active
Pll_start_auto(); // First Restart the PLL for USB operation
Wait_pll_ready(); // Get sure pll is lock
Usb_unfreeze_clock(); // Enable clock on USB interface
Host_ack_hwup(); // Clear HWUP interrupt flag
}
Host_enable_sof();
Host_send_resume(); // Send down stream resume
while (Is_host_down_stream_resume()==FALSE); // Wait Down stream resume sent
Host_ack_remote_wakeup(); // Ack remote wake-up reception
Host_ack_request_resume(); // Ack software request
Host_ack_down_stream_resume(); // Ack down stream resume sent
Usb_ack_event(EVT_HOST_HWUP); // Ack software event
if(c) { Host_enable_sof_interrupt(); } // Restore SOF interrupt enable state before suspend
device_state=DEVICE_READY; // Come back to full operating mode
LOG_STR_CODE(log_usb_resumed);
}
break;
//------------------------------------------------------
// DEVICE_DISCONNECTED state
//
// - Device disconnection has been detected
// - Run scheduler in this state at least two times to get sure event is detected by all host application tasks
// - Go to DEVICE_DISCONNECTED_ACK state before DEVICE_UNATTACHED, to get sure scheduler calls all app tasks...
//
case DEVICE_DISCONNECTED :
device_state = DEVICE_DISCONNECTED_ACK;
break;
//------------------------------------------------------
// DEVICE_DISCONNECTED_ACK state
//
// - Device disconnection has been detected and managed bu applicatives tasks
// - Go to DEVICE_UNATTACHED state
//
case DEVICE_DISCONNECTED_ACK :
device_state = DEVICE_UNATTACHED;
break;
//------------------------------------------------------
// default state
//
// - Default case: ERROR
// - Goto no device state
//
default :
device_state = DEVICE_UNATTACHED;
break;
}
}
