示例#1
0
/**
  * @brief  Enable the Global interrupt.
  * @param  DeviceAddr: Device address on communication Bus.        
  * @retval None
  */
void stmpe1600_EnableGlobalIT(uint16_t DeviceAddr)
{
  uint8_t tmpData[2] = {0 , 0};

  /* Configure NVIC IT for IOE */
  IOE_ITConfig();
  
  /* Get the current register value */
  IOE_ReadMultiple(DeviceAddr, STMPE1600_REG_SYS_CTRL, tmpData, 2);
  
  tmp = ((uint16_t)tmpData[0] | (((uint16_t)tmpData[1]) << 8));
  
  /* Set the global interrupts to be Enabled */    
  tmp |= (uint16_t)STMPE1600_IT_ENABLE;
  
  /* Write Back the Interrupt Control register */
  IOE_WriteMultiple(DeviceAddr, STMPE1600_REG_SYS_CTRL, (uint8_t *)&tmp, 2); 
}
示例#2
0
/**
  * @brief  Initialize resources used for this demo.
  * @param  None
  * @retval Digit value
  */
uint8_t Demo_Init(void)
{
  __IO uint32_t tmpValue = 0;
  PressedKey = NOKEY;

 /* Configure the IO Expander */
  if(IOE_Config() == IOE_OK)
  {
    LCD_DisplayStringLine(LINE(6), (uint8_t*)"IO Expander OK          ");
    Delay(0xFF);
  }
  else
  {
    LCD_SetTextColor(LCD_COLOR_RED);
    LCD_DisplayStringLine(LINE(6), (uint8_t*)"IO Expander FAILED Please Reset the board");
    while (1);
  }

  /* Enable the Joystick interrupt */
  IOE_ITConfig(IOE_ITSRC_JOYSTICK);

  Demo_LCD_Clear();
  LCD_DisplayStringLine(LINE(6), (uint8_t*)"Main Menu:              ");
  LCD_DisplayStringLine(LINE(7), (uint8_t*)"==========");
  LCD_DisplayStringLine(LINE(8), (uint8_t*)"Use UP and DOWN Buttons to Navigate");
  LCD_DisplayStringLine(LINE(9), (uint8_t*)"Use SEL Button to Select Image Format");

  LCD_DisplayStringLine(LINE(11), (uint8_t*)"Select the Image Format:");
  Display_Menu(ValueMin, ValueMax);

  while (1)
  {
    /* If "UP" pushbutton is pressed */
    if (PressedKey == UP)
    {
      PressedKey = NOKEY;

      /* Increase the value of the digit */
      if (tmpValue == ValueMin)
      {
        tmpValue = ValueMax - 1;
      }
      else
      {
        tmpValue--;
      }
      /* Display new Menu */
      Display_Menu(tmpValue, ValueMax);
    }
    /* If "DOWN" pushbutton is pressed */
    if (PressedKey == DOWN)
    {
      PressedKey = NOKEY;

      /* Decrease the value of the digit */
      if (tmpValue == (ValueMax - 1))
      {
        tmpValue = ValueMin;
      }
      else
      {
        tmpValue++;
      }
      /* Display new Menu */
      Display_Menu(tmpValue, ValueMax);
    }
    /* If "SEL" pushbutton is pressed */
    if (PressedKey == SEL)
    {
      PressedKey = NOKEY;

      /* Return the digit value and exit */
      return (ImageFormat_TypeDef)tmpValue;
    }
  }
}
示例#3
0
/**
  * @brief  Main program.
  * @param  None
  * @retval None
  */
int main(void)
{
  /* Initialize LEDs and push-buttons mounted on STM3210X-EVAL board */
  STM_EVAL_LEDInit(LED1);
  STM_EVAL_LEDInit(LED2);
  STM_EVAL_LEDInit(LED3);
  STM_EVAL_LEDInit(LED4);
  
   /* Initialize the LCD */
#ifdef USE_STM3210C_EVAL
  STM3210C_LCD_Init();
#elif defined (USE_STM32100E_EVAL)
  STM32100E_LCD_Init();  
#endif /* USE_STM3210C_EVAL */
 
  /* Clear the LCD */ 
  LCD_Clear(White);
  
  /* Set the LCD Back Color */
  LCD_SetBackColor(Blue);
  
  /* Set the LCD Text Color */
  LCD_SetTextColor(White);    
 
  /* Display messages on the LCD */
  LCD_DisplayStringLine(Line0, MESSAGE1);
  LCD_DisplayStringLine(Line1, MESSAGE2);
  LCD_DisplayStringLine(Line2, MESSAGE3);
  
  /* Configure the IO Expander */
  if (IOE_Config() == IOE_OK)
  {
    /* Display "IO Expander OK" on the LCD */
    LCD_DisplayStringLine(Line4, "   IO Expander OK   ");
  }
  else
  { 
    LCD_DisplayStringLine(Line4, "IO Expander FAILED ");
    LCD_DisplayStringLine(Line5, " Please Reset the  ");
    LCD_DisplayStringLine(Line6, "   board and start ");
    LCD_DisplayStringLine(Line7, "    again          ");
    while(1);
  }

  /* Draw a rectangle with the specifies parameters and Blue Color */
  LCD_SetTextColor(Blue);
  LCD_DrawRect(180, 310, 40, 60);
  
  /* Draw a rectangle with the specifies parameters and Red Color */
  LCD_SetTextColor(Red);
  LCD_DrawRect(180, 230, 40, 60);
  
  /* Draw a rectangle with the specifies parameters and Yellow Color */
  LCD_SetTextColor(Yellow);
  LCD_DrawRect(180, 150, 40, 60);
  
  /* Draw a rectangle with the specifies parameters and Black Color */
  LCD_SetTextColor(Black);
  LCD_DrawRect(180, 70, 40, 60);
  

#ifdef IOE_INTERRUPT_MODE

 #ifdef  USE_STM32100E_EVAL
  /* Enable the Touch Screen interrupts */
  IOE_ITConfig(IOE_ITSRC_TSC);
  
 #else
  /* Enable the Touch Screen and Joystick interrupts */
  IOE_ITConfig(IOE_ITSRC_JOYSTICK | IOE_ITSRC_TSC);
 #endif /* USE_STM32100E_EVAL */
 
#endif /* IOE_INTERRUPT_MODE */
  
  /* Loop infinitely */
  while(1)
  {
#ifdef IOE_POLLING_MODE
 static TS_STATE* TS_State;
    
 #ifdef  USE_STM3210C_EVAL
 
    static JOY_State_TypeDef JoyState = JOY_NONE;
    
    /* Get the Joytick State */
    JoyState = IOE_JoyStickGetState();
    
    switch (JoyState)
    {
	/* None Joystick has been selected */
    case JOY_NONE:
      LCD_DisplayStringLine(Line5, "JOY:     ----       ");
      break; 
    case JOY_UP:
      LCD_DisplayStringLine(Line5, "JOY:     UP         ");
      break;     
    case JOY_DOWN:
      LCD_DisplayStringLine(Line5, "JOY:    DOWN        ");
      break;          
    case JOY_LEFT:
      LCD_DisplayStringLine(Line5, "JOY:    LEFT        ");
      break;         
    case JOY_RIGHT:
      LCD_DisplayStringLine(Line5, "JOY:    RIGHT       ");
      break;                 
    case JOY_CENTER:
      LCD_DisplayStringLine(Line5, "JOY:    CENTER      ");
      break; 
    default:
      LCD_DisplayStringLine(Line5, "JOY:    ERROR       ");
      break;         
    }
 #endif /* USE_STM3210C_EVAL */
    
   
    /* Update the structure with the current position of the Touch screen */
    TS_State = IOE_TS_GetState();  
    
    if ((TS_State->TouchDetected) && (TS_State->Y < 220) && (TS_State->Y > 180))
    {
      if ((TS_State->X > 10) && (TS_State->X < 70))
      { 
      /* Display LD4 on the LCD and turn on LED4 */
        LCD_DisplayStringLine(Line6, " LD4                ");
        STM_EVAL_LEDOn(LED4);
      }
      else if ((TS_State->X > 90) && (TS_State->X < 150))
      {
      /* Display LD3 on the LCD and turn on LED3 */
        LCD_DisplayStringLine(Line6, "      LD3           ");
        STM_EVAL_LEDOn(LED3);
      }
      else if ((TS_State->X > 170) && (TS_State->X < 230))
      {
      /* Display LD2 on the LCD and turn on LED2 */
        LCD_DisplayStringLine(Line6, "           LD2      ");
        STM_EVAL_LEDOn(LED2);
      } 
      else if ((TS_State->X > 250) && (TS_State->X < 310))
      {
      /* Display LD1 on the LCD and turn on LED1 */
        LCD_DisplayStringLine(Line6, "                LD1 ");
        STM_EVAL_LEDOn(LED1);
      }
      
    }
    else
    {
    /* Turn off LED1..4 */
      STM_EVAL_LEDOff(LED1);
      STM_EVAL_LEDOff(LED2);
      STM_EVAL_LEDOff(LED3);
      STM_EVAL_LEDOff(LED4);
    }

#endif /* IOE_POLLING_MODE */  
  }
}
/**
  * @brief  LCD & LEDs periodic handling
  * @param  localtime: the current LocalTime value
  * @retval None
  */
void Display_Periodic_Handle(__IO uint32_t localtime)
{ 
  /* 250 ms */
  if (localtime - DisplayTimer >= LCD_TIMER_MSECS)
  {
    DisplayTimer = localtime;

    /* We have got a new IP address so update the display */
    if (IPaddress != netif.ip_addr.addr)
    {
      __IO uint8_t iptab[4];
      uint8_t iptxt[20];

      /* Read the new IP address */
      IPaddress = netif.ip_addr.addr;

      iptab[0] = (uint8_t)(IPaddress >> 24);
      iptab[1] = (uint8_t)(IPaddress >> 16);
      iptab[2] = (uint8_t)(IPaddress >> 8);
      iptab[3] = (uint8_t)(IPaddress);

      sprintf((char*)iptxt, "   %d.%d.%d.%d    ", iptab[3], iptab[2], iptab[1], iptab[0]);

      /* Display the new IP address */
#if LWIP_DHCP
      if (netif.flags & NETIF_FLAG_DHCP)
      {        
		/* Display the IP address */
		LCD_DisplayStringLine(Line7, "IP address assigned ");
        LCD_DisplayStringLine(Line8, "  by a DHCP server  ");
        LCD_DisplayStringLine(Line9, iptxt);
		Delay(LCD_DELAY);
		
		/** Start the client/server application: only when a dynamic IP address has been obtained  **/
	    /* Clear the LCD */
        LCD_Clear(Black);
	    LCD_SetBackColor(Black);
        LCD_SetTextColor(White);		   	
       
	    iptab[0] = (uint8_t)(IPaddress >> 24);
        iptab[1] = (uint8_t)(IPaddress >> 16);
        iptab[2] = (uint8_t)(IPaddress >> 8);
        iptab[3] = (uint8_t)(IPaddress);
        	   
	    sprintf((char*)iptxt, "is: %d.%d.%d.%d ", iptab[3], iptab[2], iptab[1], iptab[0]);		
       
	    LCD_DisplayStringLine(Line0, " You are configured ");
	    LCD_DisplayStringLine(Line2, iptxt);

	    if(Server)
	    {
	      LCD_DisplayStringLine(Line1, "as a server, your IP");
		 
		  /* Initialize the server application */
	      server_init(); 
	    }
	    else
	    {
	      LCD_DisplayStringLine(Line1, "as a client, your IP");
		 
		  /* Configure the IO Expander */
          IOE_Config(); 
      
          /* Enable the Touch Screen and Joystick interrupts */
          IOE_ITConfig(IOE_ITSRC_TSC);
		  
		  /* Initialize the client application */
	      client_init();
	    }	        
      }