/** Handler for the CMD_PROGRAM_FLASH_ISP and CMD_PROGRAM_EEPROM_ISP commands, writing out bytes,
* words or pages of data to the attached device.
*
* \param[in] V2Command Issued V2 Protocol command byte from the host
*/
void ISPProtocol_ProgramMemory(uint8_t V2Command)
{
struct
{
uint16_t BytesToWrite;
uint8_t ProgrammingMode;
uint8_t DelayMS;
uint8_t ProgrammingCommands[3];
uint8_t PollValue1;
uint8_t PollValue2;
uint8_t ProgData[256]; // Note, the Jungo driver has a very short ACK timeout period, need to buffer the
} Write_Memory_Params; // whole page and ACK the packet as fast as possible to prevent it from aborting
Endpoint_Read_Stream_LE(&Write_Memory_Params, (sizeof(Write_Memory_Params) -
sizeof(Write_Memory_Params.ProgData)), NULL);
Write_Memory_Params.BytesToWrite = SwapEndian_16(Write_Memory_Params.BytesToWrite);
if (Write_Memory_Params.BytesToWrite > sizeof(Write_Memory_Params.ProgData))
{
Endpoint_ClearOUT();
Endpoint_SelectEndpoint(AVRISP_DATA_IN_EPADDR);
Endpoint_SetEndpointDirection(ENDPOINT_DIR_IN);
Endpoint_Write_8(V2Command);
Endpoint_Write_8(STATUS_CMD_FAILED);
Endpoint_ClearIN();
return;
}
Endpoint_Read_Stream_LE(&Write_Memory_Params.ProgData, Write_Memory_Params.BytesToWrite, NULL);
// The driver will terminate transfers that are a round multiple of the endpoint bank in size with a ZLP, need
// to catch this and discard it before continuing on with packet processing to prevent communication issues
if (((sizeof(uint8_t) + sizeof(Write_Memory_Params) - sizeof(Write_Memory_Params.ProgData)) +
Write_Memory_Params.BytesToWrite) % AVRISP_DATA_EPSIZE == 0)
{
Endpoint_ClearOUT();
Endpoint_WaitUntilReady();
}
Endpoint_ClearOUT();
Endpoint_SelectEndpoint(AVRISP_DATA_IN_EPADDR);
Endpoint_SetEndpointDirection(ENDPOINT_DIR_IN);
uint8_t ProgrammingStatus = STATUS_CMD_OK;
uint8_t PollValue = (V2Command == CMD_PROGRAM_FLASH_ISP) ? Write_Memory_Params.PollValue1 :
Write_Memory_Params.PollValue2;
uint16_t PollAddress = 0;
uint8_t* NextWriteByte = Write_Memory_Params.ProgData;
uint16_t PageStartAddress = (CurrentAddress & 0xFFFF);
for (uint16_t CurrentByte = 0; CurrentByte < Write_Memory_Params.BytesToWrite; CurrentByte++)
{
uint8_t ByteToWrite = *(NextWriteByte++);
uint8_t ProgrammingMode = Write_Memory_Params.ProgrammingMode;
/* Check to see if we need to send a LOAD EXTENDED ADDRESS command to the target */
if (MustLoadExtendedAddress)
{
ISPTarget_LoadExtendedAddress();
MustLoadExtendedAddress = false;
}
ISPTarget_SendByte(Write_Memory_Params.ProgrammingCommands[0]);
ISPTarget_SendByte(CurrentAddress >> 8);
ISPTarget_SendByte(CurrentAddress & 0xFF);
ISPTarget_SendByte(ByteToWrite);
/* AVR FLASH addressing requires us to modify the write command based on if we are writing a high
* or low byte at the current word address */
if (V2Command == CMD_PROGRAM_FLASH_ISP)
Write_Memory_Params.ProgrammingCommands[0] ^= READ_WRITE_HIGH_BYTE_MASK;
/* Check to see if we have a valid polling address */
if (!(PollAddress) && (ByteToWrite != PollValue))
{
if ((CurrentByte & 0x01) && (V2Command == CMD_PROGRAM_FLASH_ISP))
Write_Memory_Params.ProgrammingCommands[2] |= READ_WRITE_HIGH_BYTE_MASK;
else
Write_Memory_Params.ProgrammingCommands[2] &= ~READ_WRITE_HIGH_BYTE_MASK;
PollAddress = (CurrentAddress & 0xFFFF);
}
/* If in word programming mode, commit the byte to the target's memory */
if (!(ProgrammingMode & PROG_MODE_PAGED_WRITES_MASK))
{
/* If the current polling address is invalid, switch to timed delay write completion mode */
if (!(PollAddress) && !(ProgrammingMode & PROG_MODE_WORD_READYBUSY_MASK))
ProgrammingMode = (ProgrammingMode & ~PROG_MODE_WORD_VALUE_MASK) | PROG_MODE_WORD_TIMEDELAY_MASK;
ProgrammingStatus = ISPTarget_WaitForProgComplete(ProgrammingMode, PollAddress, PollValue,
Write_Memory_Params.DelayMS,
Write_Memory_Params.ProgrammingCommands[2]);
/* Abort the programming loop early if the byte/word programming failed */
if (ProgrammingStatus != STATUS_CMD_OK)
break;
/* Must reset the polling address afterwards, so it is not erroneously used for the next byte */
PollAddress = 0;
}
/* EEPROM just increments the address each byte, flash needs to increment on each word and
* also check to ensure that a LOAD EXTENDED ADDRESS command is issued each time the extended
* address boundary has been crossed during FLASH memory programming */
if ((CurrentByte & 0x01) || (V2Command == CMD_PROGRAM_EEPROM_ISP))
{
CurrentAddress++;
if ((V2Command == CMD_PROGRAM_FLASH_ISP) && !(CurrentAddress & 0xFFFF))
MustLoadExtendedAddress = true;
}
}
/* If the current page must be committed, send the PROGRAM PAGE command to the target */
if (Write_Memory_Params.ProgrammingMode & PROG_MODE_COMMIT_PAGE_MASK)
{
ISPTarget_SendByte(Write_Memory_Params.ProgrammingCommands[1]);
ISPTarget_SendByte(PageStartAddress >> 8);
ISPTarget_SendByte(PageStartAddress & 0xFF);
ISPTarget_SendByte(0x00);
/* Check if polling is enabled and possible, if not switch to timed delay mode */
if ((Write_Memory_Params.ProgrammingMode & PROG_MODE_PAGED_VALUE_MASK) && !(PollAddress))
{
Write_Memory_Params.ProgrammingMode = (Write_Memory_Params.ProgrammingMode & ~PROG_MODE_PAGED_VALUE_MASK) |
PROG_MODE_PAGED_TIMEDELAY_MASK;
}
ProgrammingStatus = ISPTarget_WaitForProgComplete(Write_Memory_Params.ProgrammingMode, PollAddress, PollValue,
Write_Memory_Params.DelayMS,
Write_Memory_Params.ProgrammingCommands[2]);
/* Check to see if the FLASH address has crossed the extended address boundary */
if ((V2Command == CMD_PROGRAM_FLASH_ISP) && !(CurrentAddress & 0xFFFF))
MustLoadExtendedAddress = true;
}
/** Handler for the CMD_PROGRAM_FLASH_ISP and CMD_PROGRAM_EEPROM_ISP commands, writing out bytes,
* words or pages of data to the attached device.
*
* \param[in] V2Command Issued V2 Protocol command byte from the host
*/
void ISPProtocol_ProgramMemory(uint8_t V2Command)
{
struct
{
uint16_t BytesToWrite;
uint8_t ProgrammingMode;
uint8_t DelayMS;
uint8_t ProgrammingCommands[3];
uint8_t PollValue1;
uint8_t PollValue2;
uint8_t ProgData[256]; // Note, the Jungo driver has a very short ACK timeout period, need to buffer the
} Write_Memory_Params; // whole page and ACK the packet as fast as possible to prevent it from aborting
Endpoint_Read_Stream_LE(&Write_Memory_Params, (sizeof(Write_Memory_Params) -
sizeof(Write_Memory_Params.ProgData)), NO_STREAM_CALLBACK);
Write_Memory_Params.BytesToWrite = SwapEndian_16(Write_Memory_Params.BytesToWrite);
if (Write_Memory_Params.BytesToWrite > sizeof(Write_Memory_Params.ProgData))
{
Endpoint_ClearOUT();
Endpoint_SelectEndpoint(AVRISP_DATA_IN_EPNUM);
Endpoint_SetEndpointDirection(ENDPOINT_DIR_IN);
Endpoint_Write_Byte(V2Command);
Endpoint_Write_Byte(STATUS_CMD_FAILED);
Endpoint_ClearIN();
return;
}
Endpoint_Read_Stream_LE(&Write_Memory_Params.ProgData, Write_Memory_Params.BytesToWrite, NO_STREAM_CALLBACK);
Endpoint_ClearOUT();
Endpoint_SelectEndpoint(AVRISP_DATA_IN_EPNUM);
Endpoint_SetEndpointDirection(ENDPOINT_DIR_IN);
uint8_t ProgrammingStatus = STATUS_CMD_OK;
uint16_t PollAddress = 0;
uint8_t PollValue = (V2Command == CMD_PROGRAM_FLASH_ISP) ? Write_Memory_Params.PollValue1 :
Write_Memory_Params.PollValue2;
uint8_t* NextWriteByte = Write_Memory_Params.ProgData;
/* Check the programming mode desired by the host, either Paged or Word memory writes */
if (Write_Memory_Params.ProgrammingMode & PROG_MODE_PAGED_WRITES_MASK)
{
uint16_t StartAddress = (CurrentAddress & 0xFFFF);
/* Check to see if we need to send a LOAD EXTENDED ADDRESS command to the target */
if (MustLoadExtendedAddress)
{
ISPTarget_LoadExtendedAddress();
MustLoadExtendedAddress = false;
}
/* Paged mode memory programming */
for (uint16_t CurrentByte = 0; CurrentByte < Write_Memory_Params.BytesToWrite; CurrentByte++)
{
bool IsOddByte = (CurrentByte & 0x01);
uint8_t ByteToWrite = *(NextWriteByte++);
ISPTarget_SendByte(Write_Memory_Params.ProgrammingCommands[0]);
ISPTarget_SendByte(CurrentAddress >> 8);
ISPTarget_SendByte(CurrentAddress & 0xFF);
ISPTarget_SendByte(ByteToWrite);
/* AVR FLASH addressing requires us to modify the write command based on if we are writing a high
* or low byte at the current word address */
if (V2Command == CMD_PROGRAM_FLASH_ISP)
Write_Memory_Params.ProgrammingCommands[0] ^= READ_WRITE_HIGH_BYTE_MASK;
/* Check to see the write completion method, to see if we have a valid polling address */
if (!(PollAddress) && (ByteToWrite != PollValue))
{
if (IsOddByte && (V2Command == CMD_PROGRAM_FLASH_ISP))
Write_Memory_Params.ProgrammingCommands[2] |= READ_WRITE_HIGH_BYTE_MASK;
PollAddress = (CurrentAddress & 0xFFFF);
}
/* EEPROM increments the address on each byte, flash needs to increment on each word */
if (IsOddByte || (V2Command == CMD_PROGRAM_EEPROM_ISP))
CurrentAddress++;
}
/* If the current page must be committed, send the PROGRAM PAGE command to the target */
if (Write_Memory_Params.ProgrammingMode & PROG_MODE_COMMIT_PAGE_MASK)
{
ISPTarget_SendByte(Write_Memory_Params.ProgrammingCommands[1]);
ISPTarget_SendByte(StartAddress >> 8);
ISPTarget_SendByte(StartAddress & 0xFF);
ISPTarget_SendByte(0x00);
/* Check if polling is possible and enabled, if not switch to timed delay mode */
if (!(PollAddress) && (Write_Memory_Params.ProgrammingMode & PROG_MODE_PAGED_VALUE_MASK))
{
Write_Memory_Params.ProgrammingMode &= ~PROG_MODE_PAGED_VALUE_MASK;
Write_Memory_Params.ProgrammingMode |= PROG_MODE_PAGED_TIMEDELAY_MASK;
}
ProgrammingStatus = ISPTarget_WaitForProgComplete(Write_Memory_Params.ProgrammingMode, PollAddress, PollValue,
Write_Memory_Params.DelayMS, Write_Memory_Params.ProgrammingCommands[2]);
/* Check to see if the FLASH address has crossed the extended address boundary */
if ((V2Command == CMD_PROGRAM_FLASH_ISP) && !(CurrentAddress & 0xFFFF))
MustLoadExtendedAddress = true;
}
