/**
* @brief Initializes the RS485 Driver enable feature according to the specified
* parameters in the UART_InitTypeDef and creates the associated handle .
* @param huart: uart handle
* @param UART_DEPolarity: select the driver enable polarity
* This parameter can be one of the following values:
* @arg UART_DE_POLARITY_HIGH: DE signal is active high
* @arg UART_DE_POLARITY_LOW: DE signal is active low
* @param UART_DEAssertionTime: Driver Enable assertion time
* 5-bit value defining the time between the activation of the DE (Driver Enable)
* signal and the beginning of the start bit. It is expressed in sample time
* units (1/8 or 1/16 bit time, depending on the oversampling rate)
* @param UART_DEDeassertionTime: Driver Enable deassertion time
* 5-bit value defining the time between the end of the last stop bit, in a
* transmitted message, and the de-activation of the DE (Driver Enable) signal.
* It is expressed in sample time units (1/8 or 1/16 bit time, depending on the
* oversampling rate).
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RS485Ex_Init(UART_HandleTypeDef *huart, uint32_t UART_DEPolarity, uint32_t UART_DEAssertionTime, uint32_t UART_DEDeassertionTime)
{
uint32_t temp = 0x0;
/* Check the UART handle allocation */
if(huart == NULL)
{
return HAL_ERROR;
}
/* Check the Driver Enable UART instance */
assert_param(IS_UART_DRIVER_ENABLE_INSTANCE(huart->Instance));
/* Check the Driver Enable polarity */
assert_param(IS_UART_DE_POLARITY(UART_DEPolarity));
/* Check the Driver Enable assertion time */
assert_param(IS_UART_ASSERTIONTIME(UART_DEAssertionTime));
/* Check the Driver Enable deassertion time */
assert_param(IS_UART_DEASSERTIONTIME(UART_DEDeassertionTime));
if(huart->State == HAL_UART_STATE_RESET)
{
/* Init the low level hardware : GPIO, CLOCK */
HAL_UART_MspInit(huart);
}
huart->State = HAL_UART_STATE_BUSY;
/* Disable the Peripheral */
__HAL_UART_DISABLE(huart);
/* Set the UART Communication parameters */
if (UART_SetConfig(huart) == HAL_ERROR)
{
return HAL_ERROR;
}
if (huart->AdvancedInit.AdvFeatureInit != UART_ADVFEATURE_NO_INIT)
{
UART_AdvFeatureConfig(huart);
}
/* Enable the Driver Enable mode by setting the DEM bit in the CR3 register */
huart->Instance->CR3 |= USART_CR3_DEM;
/* Set the Driver Enable polarity */
MODIFY_REG(huart->Instance->CR3, USART_CR3_DEP, UART_DEPolarity);
/* Set the Driver Enable assertion and deassertion times */
temp = (UART_DEAssertionTime << UART_CR1_DEAT_ADDRESS_LSB_POS);
temp |= (UART_DEDeassertionTime << UART_CR1_DEDT_ADDRESS_LSB_POS);
MODIFY_REG(huart->Instance->CR1, (USART_CR1_DEDT|USART_CR1_DEAT), temp);
/* Enable the Peripheral */
__HAL_UART_ENABLE(huart);
/* TEACK and/or REACK to check before moving huart->State to Ready */
return (UART_CheckIdleState(huart));
}
/**
* @brief Initialize the RS485 Driver enable feature according to the specified
* parameters in the UART_InitTypeDef and creates the associated handle.
* @param huart UART handle.
* @param Polarity Select the driver enable polarity.
* This parameter can be one of the following values:
* @arg @ref UART_DE_POLARITY_HIGH DE signal is active high
* @arg @ref UART_DE_POLARITY_LOW DE signal is active low
* @param AssertionTime Driver Enable assertion time:
* 5-bit value defining the time between the activation of the DE (Driver Enable)
* signal and the beginning of the start bit. It is expressed in sample time
* units (1/8 or 1/16 bit time, depending on the oversampling rate)
* @param DeassertionTime Driver Enable deassertion time:
* 5-bit value defining the time between the end of the last stop bit, in a
* transmitted message, and the de-activation of the DE (Driver Enable) signal.
* It is expressed in sample time units (1/8 or 1/16 bit time, depending on the
* oversampling rate).
* @retval HAL status
*/
HAL_StatusTypeDef HAL_RS485Ex_Init(UART_HandleTypeDef *huart, uint32_t Polarity, uint32_t AssertionTime, uint32_t DeassertionTime)
{
uint32_t temp;
/* Check the UART handle allocation */
if (huart == NULL)
{
return HAL_ERROR;
}
/* Check the Driver Enable UART instance */
assert_param(IS_UART_DRIVER_ENABLE_INSTANCE(huart->Instance));
/* Check the Driver Enable polarity */
assert_param(IS_UART_DE_POLARITY(Polarity));
/* Check the Driver Enable assertion time */
assert_param(IS_UART_ASSERTIONTIME(AssertionTime));
/* Check the Driver Enable deassertion time */
assert_param(IS_UART_DEASSERTIONTIME(DeassertionTime));
if (huart->gState == HAL_UART_STATE_RESET)
{
/* Allocate lock resource and initialize it */
huart->Lock = HAL_UNLOCKED;
#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
UART_InitCallbacksToDefault(huart);
if (huart->MspInitCallback == NULL)
{
huart->MspInitCallback = HAL_UART_MspInit;
}
/* Init the low level hardware */
huart->MspInitCallback(huart);
#else
/* Init the low level hardware : GPIO, CLOCK, CORTEX */
HAL_UART_MspInit(huart);
#endif /* (USE_HAL_UART_REGISTER_CALLBACKS) */
}
huart->gState = HAL_UART_STATE_BUSY;
/* Disable the Peripheral */
__HAL_UART_DISABLE(huart);
/* Set the UART Communication parameters */
if (UART_SetConfig(huart) == HAL_ERROR)
{
return HAL_ERROR;
}
if (huart->AdvancedInit.AdvFeatureInit != UART_ADVFEATURE_NO_INIT)
{
UART_AdvFeatureConfig(huart);
}
/* Enable the Driver Enable mode by setting the DEM bit in the CR3 register */
SET_BIT(huart->Instance->CR3, USART_CR3_DEM);
/* Set the Driver Enable polarity */
MODIFY_REG(huart->Instance->CR3, USART_CR3_DEP, Polarity);
/* Set the Driver Enable assertion and deassertion times */
temp = (AssertionTime << UART_CR1_DEAT_ADDRESS_LSB_POS);
temp |= (DeassertionTime << UART_CR1_DEDT_ADDRESS_LSB_POS);
MODIFY_REG(huart->Instance->CR1, (USART_CR1_DEDT | USART_CR1_DEAT), temp);
/* Enable the Peripheral */
__HAL_UART_ENABLE(huart);
/* TEACK and/or REACK to check before moving huart->gState and huart->RxState to Ready */
return (UART_CheckIdleState(huart));
}
