int iwl_mvm_leds_init(struct iwl_mvm *mvm)
{
int mode = iwlwifi_mod_params.led_mode;
int ret;
switch (mode) {
case IWL_LED_DEFAULT:
case IWL_LED_RF_STATE:
mode = IWL_LED_RF_STATE;
break;
case IWL_LED_DISABLE:
IWL_INFO(mvm, "Led disabled\n");
return 0;
default:
return -EINVAL;
}
mvm->led.name = kasprintf(GFP_KERNEL, "%s-led",
wiphy_name(mvm->hw->wiphy));
mvm->led.brightness_set = iwl_led_brightness_set;
mvm->led.max_brightness = 1;
if (mode == IWL_LED_RF_STATE)
mvm->led.default_trigger =
ieee80211_get_radio_led_name(mvm->hw);
ret = led_classdev_register(mvm->trans->dev, &mvm->led);
if (ret) {
kfree(mvm->led.name);
IWL_INFO(mvm, "Failed to enable led\n");
return ret;
}
return 0;
}
static int iwl_set_hw_address(struct iwl_trans *trans,
const struct iwl_cfg *cfg,
struct iwl_nvm_data *data, const __be16 *nvm_hw,
const __le16 *mac_override)
{
if (cfg->mac_addr_from_csr) {
iwl_set_hw_address_from_csr(trans, data);
} else if (cfg->nvm_type != IWL_NVM_EXT) {
const u8 *hw_addr = (const u8 *)(nvm_hw + HW_ADDR);
/* The byte order is little endian 16 bit, meaning 214365 */
data->hw_addr[0] = hw_addr[1];
data->hw_addr[1] = hw_addr[0];
data->hw_addr[2] = hw_addr[3];
data->hw_addr[3] = hw_addr[2];
data->hw_addr[4] = hw_addr[5];
data->hw_addr[5] = hw_addr[4];
} else {
iwl_set_hw_address_family_8000(trans, cfg, data,
mac_override, nvm_hw);
}
if (!is_valid_ether_addr(data->hw_addr)) {
IWL_ERR(trans, "no valid mac address was found\n");
return -EINVAL;
}
IWL_INFO(trans, "base HW address: %pM\n", data->hw_addr);
return 0;
}
int iwlagn_tx_agg_oper(struct iwl_priv *priv, struct ieee80211_vif *vif,
struct ieee80211_sta *sta, u16 tid, u8 buf_size)
{
struct iwl_station_priv *sta_priv = (void *) sta->drv_priv;
struct iwl_rxon_context *ctx = iwl_rxon_ctx_from_vif(vif);
unsigned long flags;
u16 ssn;
buf_size = min_t(int, buf_size, LINK_QUAL_AGG_FRAME_LIMIT_DEF);
spin_lock_irqsave(&priv->shrd->sta_lock, flags);
ssn = priv->tid_data[sta_priv->sta_id][tid].agg.ssn;
spin_unlock_irqrestore(&priv->shrd->sta_lock, flags);
iwl_trans_tx_agg_setup(trans(priv), ctx->ctxid, sta_priv->sta_id, tid,
buf_size, ssn);
/*
* If the limit is 0, then it wasn't initialised yet,
* use the default. We can do that since we take the
* minimum below, and we don't want to go above our
* default due to hardware restrictions.
*/
if (sta_priv->max_agg_bufsize == 0)
sta_priv->max_agg_bufsize =
LINK_QUAL_AGG_FRAME_LIMIT_DEF;
/*
* Even though in theory the peer could have different
* aggregation reorder buffer sizes for different sessions,
* our ucode doesn't allow for that and has a global limit
* for each station. Therefore, use the minimum of all the
* aggregation sessions and our default value.
*/
sta_priv->max_agg_bufsize =
min(sta_priv->max_agg_bufsize, buf_size);
if (cfg(priv)->ht_params &&
cfg(priv)->ht_params->use_rts_for_aggregation) {
/*
* switch to RTS/CTS if it is the prefer protection
* method for HT traffic
*/
sta_priv->lq_sta.lq.general_params.flags |=
LINK_QUAL_FLAGS_SET_STA_TLC_RTS_MSK;
}
priv->agg_tids_count++;
IWL_DEBUG_HT(priv, "priv->agg_tids_count = %u\n",
priv->agg_tids_count);
sta_priv->lq_sta.lq.agg_params.agg_frame_cnt_limit =
sta_priv->max_agg_bufsize;
IWL_INFO(priv, "Tx aggregation enabled on ra = %pM tid = %d\n",
sta->addr, tid);
return iwl_send_lq_cmd(priv, ctx,
&sta_priv->lq_sta.lq, CMD_ASYNC, false);
}
void iwl_mvm_mfu_assert_dump_notif(struct iwl_mvm *mvm,
struct iwl_rx_cmd_buffer *rxb)
{
struct iwl_rx_packet *pkt = rxb_addr(rxb);
struct iwl_mfu_assert_dump_notif *mfu_dump_notif = (void *)pkt->data;
__le32 *dump_data = mfu_dump_notif->data;
int n_words = le32_to_cpu(mfu_dump_notif->data_size) / sizeof(__le32);
int i;
if (mfu_dump_notif->index_num == 0)
IWL_INFO(mvm, "MFUART assert id 0x%x occurred\n",
le32_to_cpu(mfu_dump_notif->assert_id));
for (i = 0; i < n_words; i++)
IWL_DEBUG_INFO(mvm,
"MFUART assert dump, dword %u: 0x%08x\n",
le16_to_cpu(mfu_dump_notif->index_num) *
n_words + i,
le32_to_cpu(dump_data[i]));
}
/*
* This function handles the user application commands to the ucode.
*
* It retrieves the mandatory fields IWL_TM_ATTR_UCODE_CMD_ID and
* IWL_TM_ATTR_UCODE_CMD_DATA and calls to the handler to send the
* host command to the ucode.
*
* If any mandatory field is missing, -ENOMSG is replied to the user space
* application; otherwise, the actual execution result of the host command to
* ucode is replied.
*
* @hw: ieee80211_hw object that represents the device
* @tb: gnl message fields from the user space
*/
static int iwl_testmode_ucode(struct ieee80211_hw *hw, struct nlattr **tb)
{
struct iwl_priv *priv = hw->priv;
struct iwl_host_cmd cmd;
memset(&cmd, 0, sizeof(struct iwl_host_cmd));
if (!tb[IWL_TM_ATTR_UCODE_CMD_ID] ||
!tb[IWL_TM_ATTR_UCODE_CMD_DATA]) {
IWL_DEBUG_INFO(priv,
"Error finding ucode command mandatory fields\n");
return -ENOMSG;
}
cmd.flags = CMD_ON_DEMAND;
cmd.id = nla_get_u8(tb[IWL_TM_ATTR_UCODE_CMD_ID]);
cmd.data[0] = nla_data(tb[IWL_TM_ATTR_UCODE_CMD_DATA]);
cmd.len[0] = nla_len(tb[IWL_TM_ATTR_UCODE_CMD_DATA]);
cmd.dataflags[0] = IWL_HCMD_DFL_NOCOPY;
IWL_INFO(priv, "testmode ucode command ID 0x%x, flags 0x%x,"
" len %d\n", cmd.id, cmd.flags, cmd.len[0]);
/* ok, let's submit the command to ucode */
return iwl_trans_send_cmd(trans(priv), &cmd);
}
int iwl_eeprom_check_version(struct iwl_priv *priv)
{
u16 eeprom_ver;
u16 calib_ver;
eeprom_ver = iwl_eeprom_query16(priv, EEPROM_VERSION);
calib_ver = priv->cfg->ops->lib->eeprom_ops.calib_version(priv);
if (eeprom_ver < priv->cfg->eeprom_ver ||
calib_ver < priv->cfg->eeprom_calib_ver)
goto err;
IWL_INFO(priv, "device EEPROM VER=0x%x, CALIB=0x%x\n",
eeprom_ver, calib_ver);
return 0;
err:
IWL_ERR(priv, "Unsupported (too old) EEPROM VER=0x%x < 0x%x "
"CALIB=0x%x < 0x%x\n",
eeprom_ver, priv->cfg->eeprom_ver,
calib_ver, priv->cfg->eeprom_calib_ver);
return -EINVAL;
}
/*
* Reads external NVM from a file into mvm->nvm_sections
*
* HOW TO CREATE THE NVM FILE FORMAT:
* ------------------------------
* 1. create hex file, format:
* 3800 -> header
* 0000 -> header
* 5a40 -> data
*
* rev - 6 bit (word1)
* len - 10 bit (word1)
* id - 4 bit (word2)
* rsv - 12 bit (word2)
*
* 2. flip 8bits with 8 bits per line to get the right NVM file format
*
* 3. create binary file from the hex file
*
* 4. save as "iNVM_xxx.bin" under /lib/firmware
*/
static int iwl_mvm_read_external_nvm(struct iwl_mvm *mvm)
{
int ret, section_size;
u16 section_id;
const struct firmware *fw_entry;
const struct {
__le16 word1;
__le16 word2;
u8 data[];
} *file_sec;
const u8 *eof, *temp;
#define NVM_WORD1_LEN(x) (8 * (x & 0x03FF))
#define NVM_WORD2_ID(x) (x >> 12)
IWL_DEBUG_EEPROM(mvm->trans->dev, "Read from external NVM\n");
/*
* Obtain NVM image via request_firmware. Since we already used
* request_firmware_nowait() for the firmware binary load and only
* get here after that we assume the NVM request can be satisfied
* synchronously.
*/
ret = request_firmware(&fw_entry, iwlwifi_mod_params.nvm_file,
mvm->trans->dev);
if (ret) {
IWL_ERR(mvm, "ERROR: %s isn't available %d\n",
iwlwifi_mod_params.nvm_file, ret);
return ret;
}
IWL_INFO(mvm, "Loaded NVM file %s (%zu bytes)\n",
iwlwifi_mod_params.nvm_file, fw_entry->size);
if (fw_entry->size < sizeof(*file_sec)) {
IWL_ERR(mvm, "NVM file too small\n");
ret = -EINVAL;
goto out;
}
if (fw_entry->size > MAX_NVM_FILE_LEN) {
IWL_ERR(mvm, "NVM file too large\n");
ret = -EINVAL;
goto out;
}
eof = fw_entry->data + fw_entry->size;
file_sec = (void *)fw_entry->data;
while (true) {
if (file_sec->data > eof) {
IWL_ERR(mvm,
"ERROR - NVM file too short for section header\n");
ret = -EINVAL;
break;
}
/* check for EOF marker */
if (!file_sec->word1 && !file_sec->word2) {
ret = 0;
break;
}
section_size = 2 * NVM_WORD1_LEN(le16_to_cpu(file_sec->word1));
section_id = NVM_WORD2_ID(le16_to_cpu(file_sec->word2));
if (section_size > IWL_MAX_NVM_SECTION_SIZE) {
IWL_ERR(mvm, "ERROR - section too large (%d)\n",
section_size);
ret = -EINVAL;
break;
}
if (!section_size) {
IWL_ERR(mvm, "ERROR - section empty\n");
ret = -EINVAL;
break;
}
if (file_sec->data + section_size > eof) {
IWL_ERR(mvm,
"ERROR - NVM file too short for section (%d bytes)\n",
section_size);
ret = -EINVAL;
break;
}
if (WARN(section_id >= NVM_NUM_OF_SECTIONS,
"Invalid NVM section ID %d\n", section_id)) {
ret = -EINVAL;
break;
}
temp = kmemdup(file_sec->data, section_size, GFP_KERNEL);
if (!temp) {
ret = -ENOMEM;
break;
}
mvm->nvm_sections[section_id].data = temp;
mvm->nvm_sections[section_id].length = section_size;
/* advance to the next section */
file_sec = (void *)(file_sec->data + section_size);
}
out:
release_firmware(fw_entry);
return ret;
}
/*
* This function handles the user application commands for driver.
*
* It retrieves command ID carried with IWL_TM_ATTR_COMMAND and calls to the
* handlers respectively.
*
* If it's an unknown commdn ID, -ENOSYS is replied; otherwise, the returned
* value of the actual command execution is replied to the user application.
*
* If there's any message responding to the user space, IWL_TM_ATTR_SYNC_RSP
* is used for carry the message while IWL_TM_ATTR_COMMAND must set to
* IWL_TM_CMD_DEV2APP_SYNC_RSP.
*
* @hw: ieee80211_hw object that represents the device
* @tb: gnl message fields from the user space
*/
static int iwl_testmode_driver(struct ieee80211_hw *hw, struct nlattr **tb)
{
struct iwl_priv *priv = IWL_MAC80211_GET_DVM(hw);
struct iwl_trans *trans = trans(priv);
struct sk_buff *skb;
unsigned char *rsp_data_ptr = NULL;
int status = 0, rsp_data_len = 0;
u32 devid, inst_size = 0, data_size = 0;
const struct fw_img *img;
switch (nla_get_u32(tb[IWL_TM_ATTR_COMMAND])) {
case IWL_TM_CMD_APP2DEV_GET_DEVICENAME:
rsp_data_ptr = (unsigned char *)cfg(priv)->name;
rsp_data_len = strlen(cfg(priv)->name);
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy,
rsp_data_len + 20);
if (!skb) {
IWL_ERR(priv, "Memory allocation fail\n");
return -ENOMEM;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_COMMAND,
IWL_TM_CMD_DEV2APP_SYNC_RSP);
NLA_PUT(skb, IWL_TM_ATTR_SYNC_RSP,
rsp_data_len, rsp_data_ptr);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_ERR(priv, "Error sending msg : %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_LOAD_INIT_FW:
status = iwl_load_ucode_wait_alive(priv, IWL_UCODE_INIT);
if (status)
IWL_ERR(priv, "Error loading init ucode: %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_CFG_INIT_CALIB:
iwl_testmode_cfg_init_calib(priv);
priv->ucode_loaded = false;
iwl_trans_stop_device(trans);
break;
case IWL_TM_CMD_APP2DEV_LOAD_RUNTIME_FW:
status = iwl_load_ucode_wait_alive(priv, IWL_UCODE_REGULAR);
if (status) {
IWL_ERR(priv,
"Error loading runtime ucode: %d\n", status);
break;
}
status = iwl_alive_start(priv);
if (status)
IWL_ERR(priv,
"Error starting the device: %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_LOAD_WOWLAN_FW:
iwl_scan_cancel_timeout(priv, 200);
priv->ucode_loaded = false;
iwl_trans_stop_device(trans);
status = iwl_load_ucode_wait_alive(priv, IWL_UCODE_WOWLAN);
if (status) {
IWL_ERR(priv,
"Error loading WOWLAN ucode: %d\n", status);
break;
}
status = iwl_alive_start(priv);
if (status)
IWL_ERR(priv,
"Error starting the device: %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_GET_EEPROM:
if (priv->shrd->eeprom) {
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy,
cfg(priv)->base_params->eeprom_size + 20);
if (!skb) {
IWL_ERR(priv, "Memory allocation fail\n");
return -ENOMEM;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_COMMAND,
IWL_TM_CMD_DEV2APP_EEPROM_RSP);
NLA_PUT(skb, IWL_TM_ATTR_EEPROM,
cfg(priv)->base_params->eeprom_size,
priv->shrd->eeprom);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_ERR(priv, "Error sending msg : %d\n",
status);
} else
return -EFAULT;
break;
case IWL_TM_CMD_APP2DEV_FIXRATE_REQ:
if (!tb[IWL_TM_ATTR_FIXRATE]) {
IWL_ERR(priv, "Missing fixrate setting\n");
return -ENOMSG;
}
priv->tm_fixed_rate = nla_get_u32(tb[IWL_TM_ATTR_FIXRATE]);
break;
case IWL_TM_CMD_APP2DEV_GET_FW_VERSION:
IWL_INFO(priv, "uCode version raw: 0x%x\n",
priv->fw->ucode_ver);
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy, 20);
if (!skb) {
IWL_ERR(priv, "Memory allocation fail\n");
return -ENOMEM;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_FW_VERSION,
priv->fw->ucode_ver);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_ERR(priv, "Error sending msg : %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_GET_DEVICE_ID:
devid = trans(priv)->hw_id;
IWL_INFO(priv, "hw version: 0x%x\n", devid);
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy, 20);
if (!skb) {
IWL_ERR(priv, "Memory allocation fail\n");
return -ENOMEM;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_DEVICE_ID, devid);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_ERR(priv, "Error sending msg : %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_GET_FW_INFO:
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy, 20 + 8);
if (!skb) {
IWL_ERR(priv, "Memory allocation fail\n");
return -ENOMEM;
}
if (!priv->ucode_loaded) {
IWL_ERR(priv, "No uCode has not been loaded\n");
return -EINVAL;
} else {
img = &priv->fw->img[priv->shrd->ucode_type];
inst_size = img->sec[IWL_UCODE_SECTION_INST].len;
data_size = img->sec[IWL_UCODE_SECTION_DATA].len;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_FW_TYPE, priv->shrd->ucode_type);
NLA_PUT_U32(skb, IWL_TM_ATTR_FW_INST_SIZE, inst_size);
NLA_PUT_U32(skb, IWL_TM_ATTR_FW_DATA_SIZE, data_size);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_ERR(priv, "Error sending msg : %d\n", status);
break;
default:
IWL_ERR(priv, "Unknown testmode driver command ID\n");
return -ENOSYS;
}
return status;
nla_put_failure:
kfree_skb(skb);
return -EMSGSIZE;
}
/*
* This function handles the user application commands for register access.
*
* It retrieves command ID carried with IWL_TM_ATTR_COMMAND and calls to the
* handlers respectively.
*
* If it's an unknown commdn ID, -ENOSYS is returned; or -ENOMSG if the
* mandatory fields(IWL_TM_ATTR_REG_OFFSET,IWL_TM_ATTR_REG_VALUE32,
* IWL_TM_ATTR_REG_VALUE8) are missing; Otherwise 0 is replied indicating
* the success of the command execution.
*
* If IWL_TM_ATTR_COMMAND is IWL_TM_CMD_APP2DEV_REG_READ32, the register read
* value is returned with IWL_TM_ATTR_REG_VALUE32.
*
* @hw: ieee80211_hw object that represents the device
* @tb: gnl message fields from the user space
*/
static int iwl_testmode_reg(struct ieee80211_hw *hw, struct nlattr **tb)
{
struct iwl_priv *priv = IWL_MAC80211_GET_DVM(hw);
u32 ofs, val32, cmd;
u8 val8;
struct sk_buff *skb;
int status = 0;
if (!tb[IWL_TM_ATTR_REG_OFFSET]) {
IWL_ERR(priv, "Missing register offset\n");
return -ENOMSG;
}
ofs = nla_get_u32(tb[IWL_TM_ATTR_REG_OFFSET]);
IWL_INFO(priv, "testmode register access command offset 0x%x\n", ofs);
/* Allow access only to FH/CSR/HBUS in direct mode.
Since we don't have the upper bounds for the CSR and HBUS segments,
we will use only the upper bound of FH for sanity check. */
cmd = nla_get_u32(tb[IWL_TM_ATTR_COMMAND]);
if ((cmd == IWL_TM_CMD_APP2DEV_DIRECT_REG_READ32 ||
cmd == IWL_TM_CMD_APP2DEV_DIRECT_REG_WRITE32 ||
cmd == IWL_TM_CMD_APP2DEV_DIRECT_REG_WRITE8) &&
(ofs >= FH_MEM_UPPER_BOUND)) {
IWL_ERR(priv, "offset out of segment (0x0 - 0x%x)\n",
FH_MEM_UPPER_BOUND);
return -EINVAL;
}
switch (cmd) {
case IWL_TM_CMD_APP2DEV_DIRECT_REG_READ32:
val32 = iwl_read_direct32(trans(priv), ofs);
IWL_INFO(priv, "32bit value to read 0x%x\n", val32);
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy, 20);
if (!skb) {
IWL_ERR(priv, "Memory allocation fail\n");
return -ENOMEM;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_REG_VALUE32, val32);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_ERR(priv, "Error sending msg : %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_DIRECT_REG_WRITE32:
if (!tb[IWL_TM_ATTR_REG_VALUE32]) {
IWL_ERR(priv, "Missing value to write\n");
return -ENOMSG;
} else {
val32 = nla_get_u32(tb[IWL_TM_ATTR_REG_VALUE32]);
IWL_INFO(priv, "32bit value to write 0x%x\n", val32);
iwl_write_direct32(trans(priv), ofs, val32);
}
break;
case IWL_TM_CMD_APP2DEV_DIRECT_REG_WRITE8:
if (!tb[IWL_TM_ATTR_REG_VALUE8]) {
IWL_ERR(priv, "Missing value to write\n");
return -ENOMSG;
} else {
val8 = nla_get_u8(tb[IWL_TM_ATTR_REG_VALUE8]);
IWL_INFO(priv, "8bit value to write 0x%x\n", val8);
iwl_write8(trans(priv), ofs, val8);
}
break;
default:
IWL_ERR(priv, "Unknown testmode register command ID\n");
return -ENOSYS;
}
return status;
nla_put_failure:
kfree_skb(skb);
return -EMSGSIZE;
}
/**
* iwl_ucode_callback - callback when firmware was loaded
*
* If loaded successfully, copies the firmware into buffers
* for the card to fetch (via DMA).
*/
static void iwl_ucode_callback(const struct firmware *ucode_raw, void *context)
{
struct iwl_drv *drv = context;
struct iwl_fw *fw = &drv->fw;
struct iwl_ucode_header *ucode;
int err;
struct iwl_firmware_pieces pieces;
const unsigned int api_max = drv->cfg->ucode_api_max;
unsigned int api_ok = drv->cfg->ucode_api_ok;
const unsigned int api_min = drv->cfg->ucode_api_min;
u32 api_ver;
int i;
fw->ucode_capa.max_probe_length = 200;
fw->ucode_capa.standard_phy_calibration_size =
IWL_DEFAULT_STANDARD_PHY_CALIBRATE_TBL_SIZE;
if (!api_ok)
api_ok = api_max;
memset(&pieces, 0, sizeof(pieces));
if (!ucode_raw) {
if (drv->fw_index <= api_ok)
IWL_ERR(drv,
"request for firmware file '%s' failed.\n",
drv->firmware_name);
goto try_again;
}
IWL_DEBUG_INFO(drv, "Loaded firmware file '%s' (%zd bytes).\n",
drv->firmware_name, ucode_raw->size);
/* Make sure that we got at least the API version number */
if (ucode_raw->size < 4) {
IWL_ERR(drv, "File size way too small!\n");
goto try_again;
}
/* Data from ucode file: header followed by uCode images */
ucode = (struct iwl_ucode_header *)ucode_raw->data;
if (ucode->ver)
err = iwl_parse_v1_v2_firmware(drv, ucode_raw, &pieces);
else
err = iwl_parse_tlv_firmware(drv, ucode_raw, &pieces,
&fw->ucode_capa);
if (err)
goto try_again;
api_ver = IWL_UCODE_API(drv->fw.ucode_ver);
/*
* api_ver should match the api version forming part of the
* firmware filename ... but we don't check for that and only rely
* on the API version read from firmware header from here on forward
*/
/* no api version check required for experimental uCode */
if (drv->fw_index != UCODE_EXPERIMENTAL_INDEX) {
if (api_ver < api_min || api_ver > api_max) {
IWL_ERR(drv,
"Driver unable to support your firmware API. "
"Driver supports v%u, firmware is v%u.\n",
api_max, api_ver);
goto try_again;
}
if (api_ver < api_ok) {
if (api_ok != api_max)
IWL_ERR(drv, "Firmware has old API version, "
"expected v%u through v%u, got v%u.\n",
api_ok, api_max, api_ver);
else
IWL_ERR(drv, "Firmware has old API version, "
"expected v%u, got v%u.\n",
api_max, api_ver);
IWL_ERR(drv, "New firmware can be obtained from "
"http://www.intellinuxwireless.org/.\n");
}
}
IWL_INFO(drv, "loaded firmware version %s", drv->fw.fw_version);
/*
* In mvm uCode there is no difference between data and instructions
* sections.
*/
if (!fw->mvm_fw && validate_sec_sizes(drv, &pieces, drv->cfg))
goto try_again;
/* Allocate ucode buffers for card's bus-master loading ... */
/* Runtime instructions and 2 copies of data:
* 1) unmodified from disk
* 2) backup cache for save/restore during power-downs */
for (i = 0; i < IWL_UCODE_TYPE_MAX; i++)
if (iwl_alloc_ucode(drv, &pieces, i))
goto out_free_fw;
/* Now that we can no longer fail, copy information */
/*
* The (size - 16) / 12 formula is based on the information recorded
* for each event, which is of mode 1 (including timestamp) for all
* new microcodes that include this information.
*/
fw->init_evtlog_ptr = pieces.init_evtlog_ptr;
if (pieces.init_evtlog_size)
fw->init_evtlog_size = (pieces.init_evtlog_size - 16)/12;
else
fw->init_evtlog_size =
drv->cfg->base_params->max_event_log_size;
fw->init_errlog_ptr = pieces.init_errlog_ptr;
fw->inst_evtlog_ptr = pieces.inst_evtlog_ptr;
if (pieces.inst_evtlog_size)
fw->inst_evtlog_size = (pieces.inst_evtlog_size - 16)/12;
else
fw->inst_evtlog_size =
drv->cfg->base_params->max_event_log_size;
fw->inst_errlog_ptr = pieces.inst_errlog_ptr;
/*
* figure out the offset of chain noise reset and gain commands
* base on the size of standard phy calibration commands table size
*/
if (fw->ucode_capa.standard_phy_calibration_size >
IWL_MAX_PHY_CALIBRATE_TBL_SIZE)
fw->ucode_capa.standard_phy_calibration_size =
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE;
/* We have our copies now, allow OS release its copies */
release_firmware(ucode_raw);
drv->op_mode = iwl_dvm_ops.start(drv->trans, drv->cfg, &drv->fw);
if (!drv->op_mode)
goto out_unbind;
/*
* Complete the firmware request last so that
* a driver unbind (stop) doesn't run while we
* are doing the start() above.
*/
complete(&drv->request_firmware_complete);
return;
try_again:
/* try next, if any */
release_firmware(ucode_raw);
if (iwl_request_firmware(drv, false))
goto out_unbind;
return;
out_free_fw:
IWL_ERR(drv, "failed to allocate pci memory\n");
iwl_dealloc_ucode(drv);
release_firmware(ucode_raw);
out_unbind:
complete(&drv->request_firmware_complete);
device_release_driver(drv->trans->dev);
}
struct iwl_mcc_update_resp *
iwl_mvm_update_mcc(struct iwl_mvm *mvm, const char *alpha2,
enum iwl_mcc_source src_id)
{
struct iwl_mcc_update_cmd mcc_update_cmd = {
.mcc = cpu_to_le16(alpha2[0] << 8 | alpha2[1]),
.source_id = (u8)src_id,
};
struct iwl_mcc_update_resp *resp_cp;
struct iwl_rx_packet *pkt;
struct iwl_host_cmd cmd = {
.id = MCC_UPDATE_CMD,
.flags = CMD_WANT_SKB,
.data = { &mcc_update_cmd },
};
int ret;
u32 status;
int resp_len, n_channels;
u16 mcc;
bool resp_v2 = fw_has_capa(&mvm->fw->ucode_capa,
IWL_UCODE_TLV_CAPA_LAR_SUPPORT_V2);
if (WARN_ON_ONCE(!iwl_mvm_is_lar_supported(mvm)))
return ERR_PTR(-EOPNOTSUPP);
cmd.len[0] = sizeof(struct iwl_mcc_update_cmd);
if (!resp_v2)
cmd.len[0] = sizeof(struct iwl_mcc_update_cmd_v1);
IWL_DEBUG_LAR(mvm, "send MCC update to FW with '%c%c' src = %d\n",
alpha2[0], alpha2[1], src_id);
ret = iwl_mvm_send_cmd(mvm, &cmd);
if (ret)
return ERR_PTR(ret);
pkt = cmd.resp_pkt;
/* Extract MCC response */
if (resp_v2) {
struct iwl_mcc_update_resp *mcc_resp = (void *)pkt->data;
n_channels = __le32_to_cpu(mcc_resp->n_channels);
resp_len = sizeof(struct iwl_mcc_update_resp) +
n_channels * sizeof(__le32);
resp_cp = kmemdup(mcc_resp, resp_len, GFP_KERNEL);
} else {
struct iwl_mcc_update_resp_v1 *mcc_resp_v1 = (void *)pkt->data;
n_channels = __le32_to_cpu(mcc_resp_v1->n_channels);
resp_len = sizeof(struct iwl_mcc_update_resp) +
n_channels * sizeof(__le32);
resp_cp = kzalloc(resp_len, GFP_KERNEL);
if (resp_cp) {
resp_cp->status = mcc_resp_v1->status;
resp_cp->mcc = mcc_resp_v1->mcc;
resp_cp->cap = mcc_resp_v1->cap;
resp_cp->source_id = mcc_resp_v1->source_id;
resp_cp->n_channels = mcc_resp_v1->n_channels;
memcpy(resp_cp->channels, mcc_resp_v1->channels,
n_channels * sizeof(__le32));
}
}
if (!resp_cp) {
ret = -ENOMEM;
goto exit;
}
status = le32_to_cpu(resp_cp->status);
mcc = le16_to_cpu(resp_cp->mcc);
/* W/A for a FW/NVM issue - returns 0x00 for the world domain */
if (mcc == 0) {
mcc = 0x3030; /* "00" - world */
resp_cp->mcc = cpu_to_le16(mcc);
}
IWL_DEBUG_LAR(mvm,
"MCC response status: 0x%x. new MCC: 0x%x ('%c%c') change: %d n_chans: %d\n",
status, mcc, mcc >> 8, mcc & 0xff,
!!(status == MCC_RESP_NEW_CHAN_PROFILE), n_channels);
exit:
iwl_free_resp(&cmd);
if (ret)
return ERR_PTR(ret);
return resp_cp;
}
int iwl_mvm_init_mcc(struct iwl_mvm *mvm)
{
bool tlv_lar;
bool nvm_lar;
int retval;
struct ieee80211_regdomain *regd;
char mcc[3];
if (mvm->cfg->device_family == IWL_DEVICE_FAMILY_8000) {
tlv_lar = fw_has_capa(&mvm->fw->ucode_capa,
IWL_UCODE_TLV_CAPA_LAR_SUPPORT);
nvm_lar = mvm->nvm_data->lar_enabled;
if (tlv_lar != nvm_lar)
IWL_INFO(mvm,
"Conflict between TLV & NVM regarding enabling LAR (TLV = %s NVM =%s)\n",
tlv_lar ? "enabled" : "disabled",
nvm_lar ? "enabled" : "disabled");
}
if (!iwl_mvm_is_lar_supported(mvm))
return 0;
/*
* try to replay the last set MCC to FW. If it doesn't exist,
* queue an update to cfg80211 to retrieve the default alpha2 from FW.
*/
retval = iwl_mvm_init_fw_regd(mvm);
if (retval != -ENOENT)
return retval;
/*
* Driver regulatory hint for initial update, this also informs the
* firmware we support wifi location updates.
* Disallow scans that might crash the FW while the LAR regdomain
* is not set.
*/
mvm->lar_regdom_set = false;
regd = iwl_mvm_get_current_regdomain(mvm, NULL);
if (IS_ERR_OR_NULL(regd))
return -EIO;
if (iwl_mvm_is_wifi_mcc_supported(mvm) &&
!iwl_get_bios_mcc(mvm->dev, mcc)) {
kfree(regd);
regd = iwl_mvm_get_regdomain(mvm->hw->wiphy, mcc,
MCC_SOURCE_BIOS, NULL);
if (IS_ERR_OR_NULL(regd))
return -EIO;
}
retval = regulatory_set_wiphy_regd_sync_rtnl(mvm->hw->wiphy, regd);
kfree(regd);
return retval;
}
/*
* Reads external NVM from a file into mvm->nvm_sections
*
* HOW TO CREATE THE NVM FILE FORMAT:
* ------------------------------
* 1. create hex file, format:
* 3800 -> header
* 0000 -> header
* 5a40 -> data
*
* rev - 6 bit (word1)
* len - 10 bit (word1)
* id - 4 bit (word2)
* rsv - 12 bit (word2)
*
* 2. flip 8bits with 8 bits per line to get the right NVM file format
*
* 3. create binary file from the hex file
*
* 4. save as "iNVM_xxx.bin" under /lib/firmware
*/
static int iwl_mvm_read_external_nvm(struct iwl_mvm *mvm)
{
int ret, section_size;
u16 section_id;
const struct firmware *fw_entry;
const struct {
__le16 word1;
__le16 word2;
u8 data[];
} *file_sec;
const u8 *eof;
u8 *temp;
int max_section_size;
const __le32 *dword_buff;
#define NVM_WORD1_LEN(x) (8 * (x & 0x03FF))
#define NVM_WORD2_ID(x) (x >> 12)
#define NVM_WORD2_LEN_FAMILY_8000(x) (2 * ((x & 0xFF) << 8 | x >> 8))
#define NVM_WORD1_ID_FAMILY_8000(x) (x >> 4)
#define NVM_HEADER_0 (0x2A504C54)
#define NVM_HEADER_1 (0x4E564D2A)
#define NVM_HEADER_SIZE (4 * sizeof(u32))
IWL_DEBUG_EEPROM(mvm->trans->dev, "Read from external NVM\n");
/* Maximal size depends on HW family and step */
if (mvm->trans->cfg->device_family != IWL_DEVICE_FAMILY_8000)
max_section_size = IWL_MAX_NVM_SECTION_SIZE;
else
max_section_size = IWL_MAX_NVM_8000_SECTION_SIZE;
/*
* Obtain NVM image via request_firmware. Since we already used
* request_firmware_nowait() for the firmware binary load and only
* get here after that we assume the NVM request can be satisfied
* synchronously.
*/
ret = request_firmware(&fw_entry, mvm->nvm_file_name,
mvm->trans->dev);
if (ret) {
IWL_ERR(mvm, "ERROR: %s isn't available %d\n",
mvm->nvm_file_name, ret);
return ret;
}
IWL_INFO(mvm, "Loaded NVM file %s (%zu bytes)\n",
mvm->nvm_file_name, fw_entry->size);
if (fw_entry->size > MAX_NVM_FILE_LEN) {
IWL_ERR(mvm, "NVM file too large\n");
ret = -EINVAL;
goto out;
}
eof = fw_entry->data + fw_entry->size;
dword_buff = (__le32 *)fw_entry->data;
/* some NVM file will contain a header.
* The header is identified by 2 dwords header as follow:
* dword[0] = 0x2A504C54
* dword[1] = 0x4E564D2A
*
* This header must be skipped when providing the NVM data to the FW.
*/
if (fw_entry->size > NVM_HEADER_SIZE &&
dword_buff[0] == cpu_to_le32(NVM_HEADER_0) &&
dword_buff[1] == cpu_to_le32(NVM_HEADER_1)) {
file_sec = (void *)(fw_entry->data + NVM_HEADER_SIZE);
IWL_INFO(mvm, "NVM Version %08X\n", le32_to_cpu(dword_buff[2]));
IWL_INFO(mvm, "NVM Manufacturing date %08X\n",
le32_to_cpu(dword_buff[3]));
/* nvm file validation, dword_buff[2] holds the file version */
if ((CSR_HW_REV_STEP(mvm->trans->hw_rev) == SILICON_C_STEP &&
le32_to_cpu(dword_buff[2]) < 0xE4A) ||
(CSR_HW_REV_STEP(mvm->trans->hw_rev) == SILICON_B_STEP &&
le32_to_cpu(dword_buff[2]) >= 0xE4A)) {
ret = -EFAULT;
goto out;
}
} else {
file_sec = (void *)fw_entry->data;
}
while (true) {
if (file_sec->data > eof) {
IWL_ERR(mvm,
"ERROR - NVM file too short for section header\n");
ret = -EINVAL;
break;
}
/* check for EOF marker */
if (!file_sec->word1 && !file_sec->word2) {
ret = 0;
break;
}
if (mvm->trans->cfg->device_family != IWL_DEVICE_FAMILY_8000) {
section_size =
2 * NVM_WORD1_LEN(le16_to_cpu(file_sec->word1));
section_id = NVM_WORD2_ID(le16_to_cpu(file_sec->word2));
} else {
section_size = 2 * NVM_WORD2_LEN_FAMILY_8000(
le16_to_cpu(file_sec->word2));
section_id = NVM_WORD1_ID_FAMILY_8000(
le16_to_cpu(file_sec->word1));
}
if (section_size > max_section_size) {
IWL_ERR(mvm, "ERROR - section too large (%d)\n",
section_size);
ret = -EINVAL;
break;
}
if (!section_size) {
IWL_ERR(mvm, "ERROR - section empty\n");
ret = -EINVAL;
break;
}
if (file_sec->data + section_size > eof) {
IWL_ERR(mvm,
"ERROR - NVM file too short for section (%d bytes)\n",
section_size);
ret = -EINVAL;
break;
}
if (WARN(section_id >= NVM_MAX_NUM_SECTIONS,
"Invalid NVM section ID %d\n", section_id)) {
ret = -EINVAL;
break;
}
temp = kmemdup(file_sec->data, section_size, GFP_KERNEL);
if (!temp) {
ret = -ENOMEM;
break;
}
iwl_mvm_nvm_fixups(mvm, section_id, temp, section_size);
kfree(mvm->nvm_sections[section_id].data);
mvm->nvm_sections[section_id].data = temp;
mvm->nvm_sections[section_id].length = section_size;
/* advance to the next section */
file_sec = (void *)(file_sec->data + section_size);
}
out:
release_firmware(fw_entry);
return ret;
}
static void iwl_mvm_send_led_fw_cmd(struct iwl_mvm *mvm, bool on)
{
struct iwl_led_cmd led_cmd = {
.status = cpu_to_le32(on),
};
struct iwl_host_cmd cmd = {
.id = WIDE_ID(LONG_GROUP, LEDS_CMD),
.len = { sizeof(led_cmd), },
.data = { &led_cmd, },
.flags = CMD_ASYNC,
};
int err;
if (!iwl_mvm_firmware_running(mvm))
return;
err = iwl_mvm_send_cmd(mvm, &cmd);
if (err)
IWL_WARN(mvm, "LED command failed: %d\n", err);
}
static void iwl_mvm_led_set(struct iwl_mvm *mvm, bool on)
{
if (fw_has_capa(&mvm->fw->ucode_capa,
IWL_UCODE_TLV_CAPA_LED_CMD_SUPPORT)) {
iwl_mvm_send_led_fw_cmd(mvm, on);
return;
}
iwl_write32(mvm->trans, CSR_LED_REG,
on ? CSR_LED_REG_TURN_ON : CSR_LED_REG_TURN_OFF);
}
static void iwl_led_brightness_set(struct led_classdev *led_cdev,
enum led_brightness brightness)
{
struct iwl_mvm *mvm = container_of(led_cdev, struct iwl_mvm, led);
iwl_mvm_led_set(mvm, brightness > 0);
}
int iwl_mvm_leds_init(struct iwl_mvm *mvm)
{
int mode = iwlwifi_mod_params.led_mode;
int ret;
switch (mode) {
case IWL_LED_BLINK:
IWL_ERR(mvm, "Blink led mode not supported, used default\n");
/* fall through */
case IWL_LED_DEFAULT:
case IWL_LED_RF_STATE:
mode = IWL_LED_RF_STATE;
break;
case IWL_LED_DISABLE:
IWL_INFO(mvm, "Led disabled\n");
return 0;
default:
return -EINVAL;
}
mvm->led.name = kasprintf(GFP_KERNEL, "%s-led",
wiphy_name(mvm->hw->wiphy));
mvm->led.brightness_set = iwl_led_brightness_set;
mvm->led.max_brightness = 1;
if (mode == IWL_LED_RF_STATE)
mvm->led.default_trigger =
ieee80211_get_radio_led_name(mvm->hw);
ret = led_classdev_register(mvm->trans->dev, &mvm->led);
if (ret) {
kfree(mvm->led.name);
IWL_INFO(mvm, "Failed to enable led\n");
return ret;
}
mvm->init_status |= IWL_MVM_INIT_STATUS_LEDS_INIT_COMPLETE;
return 0;
}
/*
* This function handles the user application commands for register access.
*
* It retrieves command ID carried with IWL_TM_ATTR_COMMAND and calls to the
* handlers respectively.
*
* If it's an unknown commdn ID, -ENOSYS is returned; or -ENOMSG if the
* mandatory fields(IWL_TM_ATTR_REG_OFFSET,IWL_TM_ATTR_REG_VALUE32,
* IWL_TM_ATTR_REG_VALUE8) are missing; Otherwise 0 is replied indicating
* the success of the command execution.
*
* If IWL_TM_ATTR_COMMAND is IWL_TM_CMD_APP2DEV_REG_READ32, the register read
* value is returned with IWL_TM_ATTR_REG_VALUE32.
*
* @hw: ieee80211_hw object that represents the device
* @tb: gnl message fields from the user space
*/
static int iwl_testmode_reg(struct ieee80211_hw *hw, struct nlattr **tb)
{
struct iwl_priv *priv = hw->priv;
u32 ofs, val32;
u8 val8;
struct sk_buff *skb;
int status = 0;
if (!tb[IWL_TM_ATTR_REG_OFFSET]) {
IWL_DEBUG_INFO(priv, "Error finding register offset\n");
return -ENOMSG;
}
ofs = nla_get_u32(tb[IWL_TM_ATTR_REG_OFFSET]);
IWL_INFO(priv, "testmode register access command offset 0x%x\n", ofs);
switch (nla_get_u32(tb[IWL_TM_ATTR_COMMAND])) {
case IWL_TM_CMD_APP2DEV_DIRECT_REG_READ32:
val32 = iwl_read32(bus(priv), ofs);
IWL_INFO(priv, "32bit value to read 0x%x\n", val32);
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy, 20);
if (!skb) {
IWL_DEBUG_INFO(priv, "Error allocating memory\n");
return -ENOMEM;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_REG_VALUE32, val32);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_DEBUG_INFO(priv,
"Error sending msg : %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_DIRECT_REG_WRITE32:
if (!tb[IWL_TM_ATTR_REG_VALUE32]) {
IWL_DEBUG_INFO(priv,
"Error finding value to write\n");
return -ENOMSG;
} else {
val32 = nla_get_u32(tb[IWL_TM_ATTR_REG_VALUE32]);
IWL_INFO(priv, "32bit value to write 0x%x\n", val32);
iwl_write32(bus(priv), ofs, val32);
}
break;
case IWL_TM_CMD_APP2DEV_DIRECT_REG_WRITE8:
if (!tb[IWL_TM_ATTR_REG_VALUE8]) {
IWL_DEBUG_INFO(priv, "Error finding value to write\n");
return -ENOMSG;
} else {
val8 = nla_get_u8(tb[IWL_TM_ATTR_REG_VALUE8]);
IWL_INFO(priv, "8bit value to write 0x%x\n", val8);
iwl_write8(bus(priv), ofs, val8);
}
break;
case IWL_TM_CMD_APP2DEV_INDIRECT_REG_READ32:
val32 = iwl_read_prph(bus(priv), ofs);
IWL_INFO(priv, "32bit value to read 0x%x\n", val32);
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy, 20);
if (!skb) {
IWL_DEBUG_INFO(priv, "Error allocating memory\n");
return -ENOMEM;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_REG_VALUE32, val32);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_DEBUG_INFO(priv,
"Error sending msg : %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_INDIRECT_REG_WRITE32:
if (!tb[IWL_TM_ATTR_REG_VALUE32]) {
IWL_DEBUG_INFO(priv,
"Error finding value to write\n");
return -ENOMSG;
} else {
val32 = nla_get_u32(tb[IWL_TM_ATTR_REG_VALUE32]);
IWL_INFO(priv, "32bit value to write 0x%x\n", val32);
iwl_write_prph(bus(priv), ofs, val32);
}
break;
default:
IWL_DEBUG_INFO(priv, "Unknown testmode register command ID\n");
return -ENOSYS;
}
return status;
nla_put_failure:
kfree_skb(skb);
return -EMSGSIZE;
}
static int iwl_mvm_load_ucode_wait_alive(struct iwl_mvm *mvm,
enum iwl_ucode_type ucode_type)
{
struct iwl_notification_wait alive_wait;
struct iwl_mvm_alive_data alive_data;
const struct fw_img *fw;
int ret, i;
enum iwl_ucode_type old_type = mvm->fwrt.cur_fw_img;
static const u16 alive_cmd[] = { MVM_ALIVE };
set_bit(IWL_FWRT_STATUS_WAIT_ALIVE, &mvm->fwrt.status);
if (ucode_type == IWL_UCODE_REGULAR &&
iwl_fw_dbg_conf_usniffer(mvm->fw, FW_DBG_START_FROM_ALIVE) &&
!(fw_has_capa(&mvm->fw->ucode_capa,
IWL_UCODE_TLV_CAPA_USNIFFER_UNIFIED)))
fw = iwl_get_ucode_image(mvm->fw, IWL_UCODE_REGULAR_USNIFFER);
else
fw = iwl_get_ucode_image(mvm->fw, ucode_type);
if (WARN_ON(!fw))
return -EINVAL;
iwl_fw_set_current_image(&mvm->fwrt, ucode_type);
clear_bit(IWL_MVM_STATUS_FIRMWARE_RUNNING, &mvm->status);
iwl_init_notification_wait(&mvm->notif_wait, &alive_wait,
alive_cmd, ARRAY_SIZE(alive_cmd),
iwl_alive_fn, &alive_data);
ret = iwl_trans_start_fw(mvm->trans, fw, ucode_type == IWL_UCODE_INIT);
if (ret) {
iwl_fw_set_current_image(&mvm->fwrt, old_type);
iwl_remove_notification(&mvm->notif_wait, &alive_wait);
return ret;
}
/*
* Some things may run in the background now, but we
* just wait for the ALIVE notification here.
*/
ret = iwl_wait_notification(&mvm->notif_wait, &alive_wait,
MVM_UCODE_ALIVE_TIMEOUT);
#ifdef CPTCFG_IWLWIFI_SUPPORT_DEBUG_OVERRIDES
/* let's force the timeout if required */
if (unlikely(mvm->trans->dbg_cfg.fw_alive_timeout)) {
IWL_INFO(mvm, "Forcing fw alive notification timeout\n");
ret = -ETIMEDOUT;
}
#endif
if (ret) {
struct iwl_trans *trans = mvm->trans;
if (trans->cfg->device_family >= IWL_DEVICE_FAMILY_22000)
IWL_ERR(mvm,
"SecBoot CPU1 Status: 0x%x, CPU2 Status: 0x%x\n",
iwl_read_prph(trans, UMAG_SB_CPU_1_STATUS),
iwl_read_prph(trans, UMAG_SB_CPU_2_STATUS));
else if (trans->cfg->device_family >= IWL_DEVICE_FAMILY_8000)
IWL_ERR(mvm,
"SecBoot CPU1 Status: 0x%x, CPU2 Status: 0x%x\n",
iwl_read_prph(trans, SB_CPU_1_STATUS),
iwl_read_prph(trans, SB_CPU_2_STATUS));
iwl_fw_set_current_image(&mvm->fwrt, old_type);
return ret;
}
if (!alive_data.valid) {
IWL_ERR(mvm, "Loaded ucode is not valid!\n");
iwl_fw_set_current_image(&mvm->fwrt, old_type);
return -EIO;
}
iwl_trans_fw_alive(mvm->trans, alive_data.scd_base_addr);
/*
* Note: all the queues are enabled as part of the interface
* initialization, but in firmware restart scenarios they
* could be stopped, so wake them up. In firmware restart,
* mac80211 will have the queues stopped as well until the
* reconfiguration completes. During normal startup, they
* will be empty.
*/
memset(&mvm->queue_info, 0, sizeof(mvm->queue_info));
/*
* Set a 'fake' TID for the command queue, since we use the
* hweight() of the tid_bitmap as a refcount now. Not that
* we ever even consider the command queue as one we might
* want to reuse, but be safe nevertheless.
*/
mvm->queue_info[IWL_MVM_DQA_CMD_QUEUE].tid_bitmap =
BIT(IWL_MAX_TID_COUNT + 2);
for (i = 0; i < IEEE80211_MAX_QUEUES; i++)
atomic_set(&mvm->mac80211_queue_stop_count[i], 0);
set_bit(IWL_MVM_STATUS_FIRMWARE_RUNNING, &mvm->status);
clear_bit(IWL_FWRT_STATUS_WAIT_ALIVE, &mvm->fwrt.status);
return 0;
}
/*
* This function handles the user application commands for driver.
*
* It retrieves command ID carried with IWL_TM_ATTR_COMMAND and calls to the
* handlers respectively.
*
* If it's an unknown commdn ID, -ENOSYS is replied; otherwise, the returned
* value of the actual command execution is replied to the user application.
*
* If there's any message responding to the user space, IWL_TM_ATTR_SYNC_RSP
* is used for carry the message while IWL_TM_ATTR_COMMAND must set to
* IWL_TM_CMD_DEV2APP_SYNC_RSP.
*
* @hw: ieee80211_hw object that represents the device
* @tb: gnl message fields from the user space
*/
static int iwl_testmode_driver(struct ieee80211_hw *hw, struct nlattr **tb)
{
struct iwl_priv *priv = hw->priv;
struct iwl_trans *trans = trans(priv);
struct sk_buff *skb;
unsigned char *rsp_data_ptr = NULL;
int status = 0, rsp_data_len = 0;
u32 devid;
switch (nla_get_u32(tb[IWL_TM_ATTR_COMMAND])) {
case IWL_TM_CMD_APP2DEV_GET_DEVICENAME:
rsp_data_ptr = (unsigned char *)cfg(priv)->name;
rsp_data_len = strlen(cfg(priv)->name);
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy,
rsp_data_len + 20);
if (!skb) {
IWL_DEBUG_INFO(priv,
"Error allocating memory\n");
return -ENOMEM;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_COMMAND,
IWL_TM_CMD_DEV2APP_SYNC_RSP);
NLA_PUT(skb, IWL_TM_ATTR_SYNC_RSP,
rsp_data_len, rsp_data_ptr);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_DEBUG_INFO(priv, "Error sending msg : %d\n",
status);
break;
case IWL_TM_CMD_APP2DEV_LOAD_INIT_FW:
status = iwl_load_ucode_wait_alive(trans, IWL_UCODE_INIT);
if (status)
IWL_DEBUG_INFO(priv,
"Error loading init ucode: %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_CFG_INIT_CALIB:
iwl_testmode_cfg_init_calib(priv);
iwl_trans_stop_device(trans);
break;
case IWL_TM_CMD_APP2DEV_LOAD_RUNTIME_FW:
status = iwl_load_ucode_wait_alive(trans, IWL_UCODE_REGULAR);
if (status) {
IWL_DEBUG_INFO(priv,
"Error loading runtime ucode: %d\n", status);
break;
}
status = iwl_alive_start(priv);
if (status)
IWL_DEBUG_INFO(priv,
"Error starting the device: %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_LOAD_WOWLAN_FW:
iwl_scan_cancel_timeout(priv, 200);
iwl_trans_stop_device(trans);
status = iwl_load_ucode_wait_alive(trans, IWL_UCODE_WOWLAN);
if (status) {
IWL_DEBUG_INFO(priv,
"Error loading WOWLAN ucode: %d\n", status);
break;
}
status = iwl_alive_start(priv);
if (status)
IWL_DEBUG_INFO(priv,
"Error starting the device: %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_GET_EEPROM:
if (priv->shrd->eeprom) {
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy,
cfg(priv)->base_params->eeprom_size + 20);
if (!skb) {
IWL_DEBUG_INFO(priv,
"Error allocating memory\n");
return -ENOMEM;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_COMMAND,
IWL_TM_CMD_DEV2APP_EEPROM_RSP);
NLA_PUT(skb, IWL_TM_ATTR_EEPROM,
cfg(priv)->base_params->eeprom_size,
priv->shrd->eeprom);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_DEBUG_INFO(priv,
"Error sending msg : %d\n",
status);
} else
return -EFAULT;
break;
case IWL_TM_CMD_APP2DEV_FIXRATE_REQ:
if (!tb[IWL_TM_ATTR_FIXRATE]) {
IWL_DEBUG_INFO(priv,
"Error finding fixrate setting\n");
return -ENOMSG;
}
priv->tm_fixed_rate = nla_get_u32(tb[IWL_TM_ATTR_FIXRATE]);
break;
case IWL_TM_CMD_APP2DEV_GET_FW_VERSION:
IWL_INFO(priv, "uCode version raw: 0x%x\n", priv->ucode_ver);
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy, 20);
if (!skb) {
IWL_DEBUG_INFO(priv, "Error allocating memory\n");
return -ENOMEM;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_FW_VERSION, priv->ucode_ver);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_DEBUG_INFO(priv,
"Error sending msg : %d\n", status);
break;
case IWL_TM_CMD_APP2DEV_GET_DEVICE_ID:
devid = bus_get_hw_id(bus(priv));
IWL_INFO(priv, "hw version: 0x%x\n", devid);
skb = cfg80211_testmode_alloc_reply_skb(hw->wiphy, 20);
if (!skb) {
IWL_DEBUG_INFO(priv, "Error allocating memory\n");
return -ENOMEM;
}
NLA_PUT_U32(skb, IWL_TM_ATTR_DEVICE_ID, devid);
status = cfg80211_testmode_reply(skb);
if (status < 0)
IWL_DEBUG_INFO(priv,
"Error sending msg : %d\n", status);
break;
default:
IWL_DEBUG_INFO(priv, "Unknown testmode driver command ID\n");
return -ENOSYS;
}
return status;
nla_put_failure:
kfree_skb(skb);
return -EMSGSIZE;
}
static struct iwl_op_mode *
iwl_op_mode_mvm_start(struct iwl_trans *trans, const struct iwl_cfg *cfg,
const struct iwl_fw *fw, struct dentry *dbgfs_dir)
{
struct ieee80211_hw *hw;
struct iwl_op_mode *op_mode;
struct iwl_mvm *mvm;
struct iwl_trans_config trans_cfg = {};
static const u8 no_reclaim_cmds[] = {
TX_CMD,
};
int err, scan_size;
/********************************
* 1. Allocating and configuring HW data
********************************/
hw = ieee80211_alloc_hw(sizeof(struct iwl_op_mode) +
sizeof(struct iwl_mvm),
&iwl_mvm_hw_ops);
if (!hw)
return NULL;
op_mode = hw->priv;
op_mode->ops = &iwl_mvm_ops;
op_mode->trans = trans;
mvm = IWL_OP_MODE_GET_MVM(op_mode);
mvm->dev = trans->dev;
mvm->trans = trans;
mvm->cfg = cfg;
mvm->fw = fw;
mvm->hw = hw;
mvm->restart_fw = iwlwifi_mod_params.restart_fw ? -1 : 0;
mutex_init(&mvm->mutex);
spin_lock_init(&mvm->async_handlers_lock);
INIT_LIST_HEAD(&mvm->time_event_list);
INIT_LIST_HEAD(&mvm->async_handlers_list);
spin_lock_init(&mvm->time_event_lock);
INIT_WORK(&mvm->async_handlers_wk, iwl_mvm_async_handlers_wk);
INIT_WORK(&mvm->roc_done_wk, iwl_mvm_roc_done_wk);
INIT_WORK(&mvm->sta_drained_wk, iwl_mvm_sta_drained_wk);
SET_IEEE80211_DEV(mvm->hw, mvm->trans->dev);
/*
* Populate the state variables that the transport layer needs
* to know about.
*/
trans_cfg.op_mode = op_mode;
trans_cfg.no_reclaim_cmds = no_reclaim_cmds;
trans_cfg.n_no_reclaim_cmds = ARRAY_SIZE(no_reclaim_cmds);
trans_cfg.rx_buf_size_8k = iwlwifi_mod_params.amsdu_size_8K;
if (mvm->fw->ucode_capa.flags & IWL_UCODE_TLV_FLAGS_DW_BC_TABLE)
trans_cfg.bc_table_dword = true;
if (!iwlwifi_mod_params.wd_disable)
trans_cfg.queue_watchdog_timeout = cfg->base_params->wd_timeout;
else
trans_cfg.queue_watchdog_timeout = IWL_WATCHDOG_DISABLED;
trans_cfg.command_names = iwl_mvm_cmd_strings;
trans_cfg.cmd_queue = IWL_MVM_CMD_QUEUE;
trans_cfg.cmd_fifo = IWL_MVM_CMD_FIFO;
snprintf(mvm->hw->wiphy->fw_version,
sizeof(mvm->hw->wiphy->fw_version),
"%s", fw->fw_version);
/* Configure transport layer */
iwl_trans_configure(mvm->trans, &trans_cfg);
trans->rx_mpdu_cmd = REPLY_RX_MPDU_CMD;
trans->rx_mpdu_cmd_hdr_size = sizeof(struct iwl_rx_mpdu_res_start);
/* set up notification wait support */
iwl_notification_wait_init(&mvm->notif_wait);
/* Init phy db */
mvm->phy_db = iwl_phy_db_init(trans);
if (!mvm->phy_db) {
IWL_ERR(mvm, "Cannot init phy_db\n");
goto out_free;
}
IWL_INFO(mvm, "Detected %s, REV=0x%X\n",
mvm->cfg->name, mvm->trans->hw_rev);
err = iwl_trans_start_hw(mvm->trans);
if (err)
goto out_free;
iwl_mvm_tt_initialize(mvm);
mutex_lock(&mvm->mutex);
err = iwl_run_init_mvm_ucode(mvm, true);
mutex_unlock(&mvm->mutex);
/* returns 0 if successful, 1 if success but in rfkill */
if (err < 0 && !iwlmvm_mod_params.init_dbg) {
IWL_ERR(mvm, "Failed to run INIT ucode: %d\n", err);
goto out_free;
}
/* Stop the hw after the ALIVE and NVM has been read */
if (!iwlmvm_mod_params.init_dbg)
iwl_trans_stop_hw(mvm->trans, false);
scan_size = sizeof(struct iwl_scan_cmd) +
mvm->fw->ucode_capa.max_probe_length +
(MAX_NUM_SCAN_CHANNELS * sizeof(struct iwl_scan_channel));
mvm->scan_cmd = kmalloc(scan_size, GFP_KERNEL);
if (!mvm->scan_cmd)
goto out_free;
err = iwl_mvm_mac_setup_register(mvm);
if (err)
goto out_free;
err = iwl_mvm_dbgfs_register(mvm, dbgfs_dir);
if (err)
goto out_unregister;
if (mvm->fw->ucode_capa.flags & IWL_UCODE_TLV_FLAGS_UAPSD)
mvm->pm_ops = &pm_mac_ops;
else
mvm->pm_ops = &pm_legacy_ops;
memset(&mvm->rx_stats, 0, sizeof(struct mvm_statistics_rx));
return op_mode;
out_unregister:
ieee80211_unregister_hw(mvm->hw);
out_free:
iwl_phy_db_free(mvm->phy_db);
kfree(mvm->scan_cmd);
iwl_trans_stop_hw(trans, true);
ieee80211_free_hw(mvm->hw);
return NULL;
}
/**
* iwl_init_geos - Initialize mac80211's geo/channel info based from eeprom
*/
int iwl_init_geos(struct iwl_priv *priv)
{
struct iwl_channel_info *ch;
struct ieee80211_supported_band *sband;
struct ieee80211_channel *channels;
struct ieee80211_channel *geo_ch;
struct ieee80211_rate *rates;
int i = 0;
s8 max_tx_power = IWLAGN_TX_POWER_TARGET_POWER_MIN;
if (priv->bands[IEEE80211_BAND_2GHZ].n_bitrates ||
priv->bands[IEEE80211_BAND_5GHZ].n_bitrates) {
IWL_DEBUG_INFO(priv, "Geography modes already initialized.\n");
set_bit(STATUS_GEO_CONFIGURED, &priv->status);
return 0;
}
channels = kcalloc(priv->channel_count,
sizeof(struct ieee80211_channel), GFP_KERNEL);
if (!channels)
return -ENOMEM;
rates = kcalloc(IWL_RATE_COUNT_LEGACY, sizeof(struct ieee80211_rate),
GFP_KERNEL);
if (!rates) {
kfree(channels);
return -ENOMEM;
}
/* 5.2GHz channels start after the 2.4GHz channels */
sband = &priv->bands[IEEE80211_BAND_5GHZ];
sband->channels = &channels[ARRAY_SIZE(iwl_eeprom_band_1)];
/* just OFDM */
sband->bitrates = &rates[IWL_FIRST_OFDM_RATE];
sband->n_bitrates = IWL_RATE_COUNT_LEGACY - IWL_FIRST_OFDM_RATE;
if (hw_params(priv).sku & EEPROM_SKU_CAP_11N_ENABLE)
iwl_init_ht_hw_capab(priv, &sband->ht_cap,
IEEE80211_BAND_5GHZ);
sband = &priv->bands[IEEE80211_BAND_2GHZ];
sband->channels = channels;
/* OFDM & CCK */
sband->bitrates = rates;
sband->n_bitrates = IWL_RATE_COUNT_LEGACY;
if (hw_params(priv).sku & EEPROM_SKU_CAP_11N_ENABLE)
iwl_init_ht_hw_capab(priv, &sband->ht_cap,
IEEE80211_BAND_2GHZ);
priv->ieee_channels = channels;
priv->ieee_rates = rates;
for (i = 0; i < priv->channel_count; i++) {
ch = &priv->channel_info[i];
/* FIXME: might be removed if scan is OK */
if (!is_channel_valid(ch))
continue;
sband = &priv->bands[ch->band];
geo_ch = &sband->channels[sband->n_channels++];
geo_ch->center_freq =
ieee80211_channel_to_frequency(ch->channel, ch->band);
geo_ch->max_power = ch->max_power_avg;
geo_ch->max_antenna_gain = 0xff;
geo_ch->hw_value = ch->channel;
if (is_channel_valid(ch)) {
if (!(ch->flags & EEPROM_CHANNEL_IBSS))
geo_ch->flags |= IEEE80211_CHAN_NO_IBSS;
if (!(ch->flags & EEPROM_CHANNEL_ACTIVE))
geo_ch->flags |= IEEE80211_CHAN_PASSIVE_SCAN;
if (ch->flags & EEPROM_CHANNEL_RADAR)
geo_ch->flags |= IEEE80211_CHAN_RADAR;
geo_ch->flags |= ch->ht40_extension_channel;
if (ch->max_power_avg > max_tx_power)
max_tx_power = ch->max_power_avg;
} else {
geo_ch->flags |= IEEE80211_CHAN_DISABLED;
}
IWL_DEBUG_INFO(priv, "Channel %d Freq=%d[%sGHz] %s flag=0x%X\n",
ch->channel, geo_ch->center_freq,
is_channel_a_band(ch) ? "5.2" : "2.4",
geo_ch->flags & IEEE80211_CHAN_DISABLED ?
"restricted" : "valid",
geo_ch->flags);
}
priv->tx_power_device_lmt = max_tx_power;
priv->tx_power_user_lmt = max_tx_power;
priv->tx_power_next = max_tx_power;
if ((priv->bands[IEEE80211_BAND_5GHZ].n_channels == 0) &&
hw_params(priv).sku & EEPROM_SKU_CAP_BAND_52GHZ) {
IWL_INFO(priv, "Incorrectly detected BG card as ABG. "
"Please send your %s to maintainer.\n",
trans(priv)->hw_id_str);
hw_params(priv).sku &= ~EEPROM_SKU_CAP_BAND_52GHZ;
}
IWL_INFO(priv, "Tunable channels: %d 802.11bg, %d 802.11a channels\n",
priv->bands[IEEE80211_BAND_2GHZ].n_channels,
priv->bands[IEEE80211_BAND_5GHZ].n_channels);
set_bit(STATUS_GEO_CONFIGURED, &priv->status);
return 0;
}
static void iwl_ucode_callback(const struct firmware *ucode_raw, void *context)
{
struct iwl_drv *drv = context;
const struct iwl_cfg *cfg = cfg(drv);
struct iwl_fw *fw = &drv->fw;
struct iwl_ucode_header *ucode;
int err;
struct iwl_firmware_pieces pieces;
const unsigned int api_max = cfg->ucode_api_max;
unsigned int api_ok = cfg->ucode_api_ok;
const unsigned int api_min = cfg->ucode_api_min;
u32 api_ver;
int i;
fw->ucode_capa.max_probe_length = 200;
fw->ucode_capa.standard_phy_calibration_size =
IWL_DEFAULT_STANDARD_PHY_CALIBRATE_TBL_SIZE;
if (!api_ok)
api_ok = api_max;
memset(&pieces, 0, sizeof(pieces));
if (!ucode_raw) {
if (drv->fw_index <= api_ok)
IWL_ERR(drv,
"request for firmware file '%s' failed.\n",
drv->firmware_name);
goto try_again;
}
IWL_DEBUG_INFO(drv, "Loaded firmware file '%s' (%zd bytes).\n",
drv->firmware_name, ucode_raw->size);
if (ucode_raw->size < 4) {
IWL_ERR(drv, "File size way too small!\n");
goto try_again;
}
ucode = (struct iwl_ucode_header *)ucode_raw->data;
if (ucode->ver)
err = iwl_parse_v1_v2_firmware(drv, ucode_raw, &pieces);
else
err = iwl_parse_tlv_firmware(drv, ucode_raw, &pieces,
&fw->ucode_capa);
if (err)
goto try_again;
api_ver = IWL_UCODE_API(drv->fw.ucode_ver);
if (drv->fw_index != UCODE_EXPERIMENTAL_INDEX) {
if (api_ver < api_min || api_ver > api_max) {
IWL_ERR(drv,
"Driver unable to support your firmware API. "
"Driver supports v%u, firmware is v%u.\n",
api_max, api_ver);
goto try_again;
}
if (api_ver < api_ok) {
if (api_ok != api_max)
IWL_ERR(drv, "Firmware has old API version, "
"expected v%u through v%u, got v%u.\n",
api_ok, api_max, api_ver);
else
IWL_ERR(drv, "Firmware has old API version, "
"expected v%u, got v%u.\n",
api_max, api_ver);
IWL_ERR(drv, "New firmware can be obtained from "
"http://www.intellinuxwireless.org/.\n");
}
}
IWL_INFO(drv, "loaded firmware version %s", drv->fw.fw_version);
IWL_DEBUG_INFO(drv, "f/w package hdr ucode version raw = 0x%x\n",
drv->fw.ucode_ver);
IWL_DEBUG_INFO(drv, "f/w package hdr runtime inst size = %Zd\n",
get_sec_size(&pieces, IWL_UCODE_REGULAR,
IWL_UCODE_SECTION_INST));
IWL_DEBUG_INFO(drv, "f/w package hdr runtime data size = %Zd\n",
get_sec_size(&pieces, IWL_UCODE_REGULAR,
IWL_UCODE_SECTION_DATA));
IWL_DEBUG_INFO(drv, "f/w package hdr init inst size = %Zd\n",
get_sec_size(&pieces, IWL_UCODE_INIT, IWL_UCODE_SECTION_INST));
IWL_DEBUG_INFO(drv, "f/w package hdr init data size = %Zd\n",
get_sec_size(&pieces, IWL_UCODE_INIT, IWL_UCODE_SECTION_DATA));
if (get_sec_size(&pieces, IWL_UCODE_REGULAR, IWL_UCODE_SECTION_INST) >
cfg->max_inst_size) {
IWL_ERR(drv, "uCode instr len %Zd too large to fit in\n",
get_sec_size(&pieces, IWL_UCODE_REGULAR,
IWL_UCODE_SECTION_INST));
goto try_again;
}
if (get_sec_size(&pieces, IWL_UCODE_REGULAR, IWL_UCODE_SECTION_DATA) >
cfg->max_data_size) {
IWL_ERR(drv, "uCode data len %Zd too large to fit in\n",
get_sec_size(&pieces, IWL_UCODE_REGULAR,
IWL_UCODE_SECTION_DATA));
goto try_again;
}
if (!fw->mvm_fw && validate_sec_sizes(drv, &pieces, cfg))
goto try_again;
for (i = 0; i < IWL_UCODE_TYPE_MAX; i++)
if (alloc_pci_desc(drv, &pieces, i))
goto err_pci_alloc;
fw->init_evtlog_ptr = pieces.init_evtlog_ptr;
if (pieces.init_evtlog_size)
fw->init_evtlog_size = (pieces.init_evtlog_size - 16)/12;
else
fw->init_evtlog_size =
cfg->base_params->max_event_log_size;
fw->init_errlog_ptr = pieces.init_errlog_ptr;
fw->inst_evtlog_ptr = pieces.inst_evtlog_ptr;
if (pieces.inst_evtlog_size)
fw->inst_evtlog_size = (pieces.inst_evtlog_size - 16)/12;
else
fw->inst_evtlog_size =
cfg->base_params->max_event_log_size;
fw->inst_errlog_ptr = pieces.inst_errlog_ptr;
if (fw->ucode_capa.standard_phy_calibration_size >
IWL_MAX_PHY_CALIBRATE_TBL_SIZE)
fw->ucode_capa.standard_phy_calibration_size =
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE;
release_firmware(ucode_raw);
complete(&drv->request_firmware_complete);
drv->op_mode = iwl_dvm_ops.start(drv->shrd->trans, &drv->fw);
if (!drv->op_mode)
goto out_unbind;
return;
try_again:
release_firmware(ucode_raw);
if (iwl_request_firmware(drv, false))
goto out_unbind;
return;
err_pci_alloc:
IWL_ERR(drv, "failed to allocate pci memory\n");
iwl_dealloc_ucode(drv);
release_firmware(ucode_raw);
out_unbind:
complete(&drv->request_firmware_complete);
device_release_driver(trans(drv)->dev);
}
static struct iwl_op_mode *
iwl_op_mode_mvm_start(struct iwl_trans *trans, const struct iwl_cfg *cfg,
const struct iwl_fw *fw, struct dentry *dbgfs_dir)
{
struct ieee80211_hw *hw;
struct iwl_op_mode *op_mode;
struct iwl_mvm *mvm;
struct iwl_trans_config trans_cfg = {};
static const u8 no_reclaim_cmds[] = {
TX_CMD,
};
int err, scan_size;
u32 min_backoff;
/*
* We use IWL_MVM_STATION_COUNT to check the validity of the station
* index all over the driver - check that its value corresponds to the
* array size.
*/
BUILD_BUG_ON(ARRAY_SIZE(mvm->fw_id_to_mac_id) != IWL_MVM_STATION_COUNT);
/********************************
* 1. Allocating and configuring HW data
********************************/
hw = ieee80211_alloc_hw(sizeof(struct iwl_op_mode) +
sizeof(struct iwl_mvm),
&iwl_mvm_hw_ops);
if (!hw)
return NULL;
op_mode = hw->priv;
op_mode->ops = &iwl_mvm_ops;
mvm = IWL_OP_MODE_GET_MVM(op_mode);
mvm->dev = trans->dev;
mvm->trans = trans;
mvm->cfg = cfg;
mvm->fw = fw;
mvm->hw = hw;
mvm->restart_fw = iwlwifi_mod_params.restart_fw ? -1 : 0;
mvm->aux_queue = 15;
mvm->first_agg_queue = 16;
mvm->last_agg_queue = mvm->cfg->base_params->num_of_queues - 1;
if (mvm->cfg->base_params->num_of_queues == 16) {
mvm->aux_queue = 11;
mvm->first_agg_queue = 12;
}
mvm->sf_state = SF_UNINIT;
mutex_init(&mvm->mutex);
mutex_init(&mvm->d0i3_suspend_mutex);
spin_lock_init(&mvm->async_handlers_lock);
INIT_LIST_HEAD(&mvm->time_event_list);
INIT_LIST_HEAD(&mvm->async_handlers_list);
spin_lock_init(&mvm->time_event_lock);
INIT_WORK(&mvm->async_handlers_wk, iwl_mvm_async_handlers_wk);
INIT_WORK(&mvm->roc_done_wk, iwl_mvm_roc_done_wk);
INIT_WORK(&mvm->sta_drained_wk, iwl_mvm_sta_drained_wk);
INIT_WORK(&mvm->d0i3_exit_work, iwl_mvm_d0i3_exit_work);
spin_lock_init(&mvm->d0i3_tx_lock);
skb_queue_head_init(&mvm->d0i3_tx);
init_waitqueue_head(&mvm->d0i3_exit_waitq);
SET_IEEE80211_DEV(mvm->hw, mvm->trans->dev);
/*
* Populate the state variables that the transport layer needs
* to know about.
*/
trans_cfg.op_mode = op_mode;
trans_cfg.no_reclaim_cmds = no_reclaim_cmds;
trans_cfg.n_no_reclaim_cmds = ARRAY_SIZE(no_reclaim_cmds);
trans_cfg.rx_buf_size_8k = iwlwifi_mod_params.amsdu_size_8K;
if (mvm->fw->ucode_capa.flags & IWL_UCODE_TLV_FLAGS_DW_BC_TABLE)
trans_cfg.bc_table_dword = true;
if (!iwlwifi_mod_params.wd_disable)
trans_cfg.queue_watchdog_timeout = cfg->base_params->wd_timeout;
else
trans_cfg.queue_watchdog_timeout = IWL_WATCHDOG_DISABLED;
trans_cfg.command_names = iwl_mvm_cmd_strings;
trans_cfg.cmd_queue = IWL_MVM_CMD_QUEUE;
trans_cfg.cmd_fifo = IWL_MVM_CMD_FIFO;
snprintf(mvm->hw->wiphy->fw_version,
sizeof(mvm->hw->wiphy->fw_version),
"%s", fw->fw_version);
/* Configure transport layer */
iwl_trans_configure(mvm->trans, &trans_cfg);
trans->rx_mpdu_cmd = REPLY_RX_MPDU_CMD;
trans->rx_mpdu_cmd_hdr_size = sizeof(struct iwl_rx_mpdu_res_start);
/* set up notification wait support */
iwl_notification_wait_init(&mvm->notif_wait);
/* Init phy db */
mvm->phy_db = iwl_phy_db_init(trans);
if (!mvm->phy_db) {
IWL_ERR(mvm, "Cannot init phy_db\n");
goto out_free;
}
IWL_INFO(mvm, "Detected %s, REV=0x%X\n",
mvm->cfg->name, mvm->trans->hw_rev);
min_backoff = calc_min_backoff(trans, cfg);
iwl_mvm_tt_initialize(mvm, min_backoff);
/* set the nvm_file_name according to priority */
if (iwlwifi_mod_params.nvm_file)
mvm->nvm_file_name = iwlwifi_mod_params.nvm_file;
else
mvm->nvm_file_name = mvm->cfg->default_nvm_file;
if (WARN(cfg->no_power_up_nic_in_init && !mvm->nvm_file_name,
"not allowing power-up and not having nvm_file\n"))
goto out_free;
/*
* Even if nvm exists in the nvm_file driver should read agin the nvm
* from the nic because there might be entries that exist in the OTP
* and not in the file.
* for nics with no_power_up_nic_in_init: rely completley on nvm_file
*/
if (cfg->no_power_up_nic_in_init && mvm->nvm_file_name) {
err = iwl_nvm_init(mvm, false);
if (err)
goto out_free;
} else {
err = iwl_trans_start_hw(mvm->trans);
if (err)
goto out_free;
mutex_lock(&mvm->mutex);
err = iwl_run_init_mvm_ucode(mvm, true);
iwl_trans_stop_device(trans);
mutex_unlock(&mvm->mutex);
/* returns 0 if successful, 1 if success but in rfkill */
if (err < 0 && !iwlmvm_mod_params.init_dbg) {
IWL_ERR(mvm, "Failed to run INIT ucode: %d\n", err);
goto out_free;
}
}
scan_size = sizeof(struct iwl_scan_cmd) +
mvm->fw->ucode_capa.max_probe_length +
(MAX_NUM_SCAN_CHANNELS * sizeof(struct iwl_scan_channel));
mvm->scan_cmd = kmalloc(scan_size, GFP_KERNEL);
if (!mvm->scan_cmd)
goto out_free;
err = iwl_mvm_mac_setup_register(mvm);
if (err)
goto out_free;
err = iwl_mvm_dbgfs_register(mvm, dbgfs_dir);
if (err)
goto out_unregister;
memset(&mvm->rx_stats, 0, sizeof(struct mvm_statistics_rx));
/* rpm starts with a taken ref. only set the appropriate bit here. */
set_bit(IWL_MVM_REF_UCODE_DOWN, mvm->ref_bitmap);
return op_mode;
out_unregister:
ieee80211_unregister_hw(mvm->hw);
iwl_mvm_leds_exit(mvm);
out_free:
iwl_phy_db_free(mvm->phy_db);
kfree(mvm->scan_cmd);
if (!cfg->no_power_up_nic_in_init || !mvm->nvm_file_name)
iwl_trans_op_mode_leave(trans);
ieee80211_free_hw(mvm->hw);
return NULL;
}
static struct iwl_op_mode *
iwl_op_mode_mvm_start(struct iwl_trans *trans, const struct iwl_cfg *cfg,
const struct iwl_fw *fw, struct dentry *dbgfs_dir)
{
struct ieee80211_hw *hw;
struct iwl_op_mode *op_mode;
struct iwl_mvm *mvm;
struct iwl_trans_config trans_cfg = {};
static const u8 no_reclaim_cmds[] = {
TX_CMD,
};
int err, scan_size;
u32 min_backoff;
/*
* We use IWL_MVM_STATION_COUNT to check the validity of the station
* index all over the driver - check that its value corresponds to the
* array size.
*/
BUILD_BUG_ON(ARRAY_SIZE(mvm->fw_id_to_mac_id) != IWL_MVM_STATION_COUNT);
/********************************
* 1. Allocating and configuring HW data
********************************/
hw = ieee80211_alloc_hw(sizeof(struct iwl_op_mode) +
sizeof(struct iwl_mvm),
&iwl_mvm_hw_ops);
if (!hw)
return NULL;
if (cfg->max_rx_agg_size)
hw->max_rx_aggregation_subframes = cfg->max_rx_agg_size;
if (cfg->max_tx_agg_size)
hw->max_tx_aggregation_subframes = cfg->max_tx_agg_size;
op_mode = hw->priv;
op_mode->ops = &iwl_mvm_ops;
mvm = IWL_OP_MODE_GET_MVM(op_mode);
mvm->dev = trans->dev;
mvm->trans = trans;
mvm->cfg = cfg;
mvm->fw = fw;
mvm->hw = hw;
mvm->restart_fw = iwlwifi_mod_params.restart_fw ? -1 : 0;
mvm->aux_queue = 15;
mvm->first_agg_queue = 16;
mvm->last_agg_queue = mvm->cfg->base_params->num_of_queues - 1;
if (mvm->cfg->base_params->num_of_queues == 16) {
mvm->aux_queue = 11;
mvm->first_agg_queue = 12;
}
mvm->sf_state = SF_UNINIT;
mvm->low_latency_agg_frame_limit = 6;
mvm->cur_ucode = IWL_UCODE_INIT;
mutex_init(&mvm->mutex);
mutex_init(&mvm->d0i3_suspend_mutex);
spin_lock_init(&mvm->async_handlers_lock);
INIT_LIST_HEAD(&mvm->time_event_list);
INIT_LIST_HEAD(&mvm->aux_roc_te_list);
INIT_LIST_HEAD(&mvm->async_handlers_list);
spin_lock_init(&mvm->time_event_lock);
mvm->workqueue = create_singlethread_workqueue(DRV_NAME);
if (!mvm->workqueue) {
ieee80211_free_hw(mvm->hw);
return NULL;
}
INIT_WORK(&mvm->async_handlers_wk, iwl_mvm_async_handlers_wk);
INIT_WORK(&mvm->roc_done_wk, iwl_mvm_roc_done_wk);
INIT_WORK(&mvm->sta_drained_wk, iwl_mvm_sta_drained_wk);
INIT_WORK(&mvm->d0i3_exit_work, iwl_mvm_d0i3_exit_work);
INIT_DELAYED_WORK(&mvm->fw_dump_wk, iwl_mvm_fw_error_dump_wk);
INIT_DELAYED_WORK(&mvm->tdls_cs.dwork, iwl_mvm_tdls_ch_switch_work);
spin_lock_init(&mvm->d0i3_tx_lock);
spin_lock_init(&mvm->refs_lock);
skb_queue_head_init(&mvm->d0i3_tx);
init_waitqueue_head(&mvm->d0i3_exit_waitq);
SET_IEEE80211_DEV(mvm->hw, mvm->trans->dev);
/*
* Populate the state variables that the transport layer needs
* to know about.
*/
trans_cfg.op_mode = op_mode;
trans_cfg.no_reclaim_cmds = no_reclaim_cmds;
trans_cfg.n_no_reclaim_cmds = ARRAY_SIZE(no_reclaim_cmds);
trans_cfg.rx_buf_size_8k = iwlwifi_mod_params.amsdu_size_8K;
if (mvm->fw->ucode_capa.flags & IWL_UCODE_TLV_FLAGS_DW_BC_TABLE)
trans_cfg.bc_table_dword = true;
trans_cfg.command_names = iwl_mvm_cmd_strings;
trans_cfg.cmd_queue = IWL_MVM_CMD_QUEUE;
trans_cfg.cmd_fifo = IWL_MVM_TX_FIFO_CMD;
trans_cfg.scd_set_active = true;
trans_cfg.sdio_adma_addr = fw->sdio_adma_addr;
/* Set a short watchdog for the command queue */
trans_cfg.cmd_q_wdg_timeout =
iwl_mvm_get_wd_timeout(mvm, NULL, false, true);
snprintf(mvm->hw->wiphy->fw_version,
sizeof(mvm->hw->wiphy->fw_version),
"%s", fw->fw_version);
/* Configure transport layer */
iwl_trans_configure(mvm->trans, &trans_cfg);
trans->rx_mpdu_cmd = REPLY_RX_MPDU_CMD;
trans->rx_mpdu_cmd_hdr_size = sizeof(struct iwl_rx_mpdu_res_start);
trans->dbg_dest_tlv = mvm->fw->dbg_dest_tlv;
trans->dbg_dest_reg_num = mvm->fw->dbg_dest_reg_num;
memcpy(trans->dbg_conf_tlv, mvm->fw->dbg_conf_tlv,
sizeof(trans->dbg_conf_tlv));
trans->dbg_trigger_tlv = mvm->fw->dbg_trigger_tlv;
/* set up notification wait support */
iwl_notification_wait_init(&mvm->notif_wait);
/* Init phy db */
mvm->phy_db = iwl_phy_db_init(trans);
if (!mvm->phy_db) {
IWL_ERR(mvm, "Cannot init phy_db\n");
goto out_free;
}
IWL_INFO(mvm, "Detected %s, REV=0x%X\n",
mvm->cfg->name, mvm->trans->hw_rev);
min_backoff = calc_min_backoff(trans, cfg);
iwl_mvm_tt_initialize(mvm, min_backoff);
/* set the nvm_file_name according to priority */
if (iwlwifi_mod_params.nvm_file) {
mvm->nvm_file_name = iwlwifi_mod_params.nvm_file;
} else if (trans->cfg->device_family == IWL_DEVICE_FAMILY_8000) {
if (CSR_HW_REV_STEP(trans->hw_rev) == SILICON_B_STEP)
mvm->nvm_file_name = mvm->cfg->default_nvm_file_B_step;
else
mvm->nvm_file_name = mvm->cfg->default_nvm_file_C_step;
}
if (WARN(cfg->no_power_up_nic_in_init && !mvm->nvm_file_name,
"not allowing power-up and not having nvm_file\n"))
goto out_free;
/*
* Even if nvm exists in the nvm_file driver should read again the nvm
* from the nic because there might be entries that exist in the OTP
* and not in the file.
* for nics with no_power_up_nic_in_init: rely completley on nvm_file
*/
if (cfg->no_power_up_nic_in_init && mvm->nvm_file_name) {
err = iwl_nvm_init(mvm, false);
if (err)
goto out_free;
} else {
err = iwl_trans_start_hw(mvm->trans);
if (err)
goto out_free;
mutex_lock(&mvm->mutex);
err = iwl_run_init_mvm_ucode(mvm, true);
if (!err || !iwlmvm_mod_params.init_dbg)
iwl_trans_stop_device(trans);
mutex_unlock(&mvm->mutex);
/* returns 0 if successful, 1 if success but in rfkill */
if (err < 0 && !iwlmvm_mod_params.init_dbg) {
IWL_ERR(mvm, "Failed to run INIT ucode: %d\n", err);
goto out_free;
}
}
scan_size = iwl_mvm_scan_size(mvm);
mvm->scan_cmd = kmalloc(scan_size, GFP_KERNEL);
if (!mvm->scan_cmd)
goto out_free;
/* Set EBS as successful as long as not stated otherwise by the FW. */
mvm->last_ebs_successful = true;
err = iwl_mvm_mac_setup_register(mvm);
if (err)
goto out_free;
err = iwl_mvm_dbgfs_register(mvm, dbgfs_dir);
if (err)
goto out_unregister;
memset(&mvm->rx_stats, 0, sizeof(struct mvm_statistics_rx));
/* rpm starts with a taken ref. only set the appropriate bit here. */
mvm->refs[IWL_MVM_REF_UCODE_DOWN] = 1;
return op_mode;
out_unregister:
ieee80211_unregister_hw(mvm->hw);
iwl_mvm_leds_exit(mvm);
out_free:
iwl_phy_db_free(mvm->phy_db);
kfree(mvm->scan_cmd);
if (!cfg->no_power_up_nic_in_init || !mvm->nvm_file_name)
iwl_trans_op_mode_leave(trans);
destroy_workqueue(mvm->workqueue);
ieee80211_free_hw(mvm->hw);
return NULL;
}