void power_on(void)
{
power_state = 1;
#if 0
LCD_PowerOn();
#endif
Refresh();
}
static DISP_STATUS dbi_enable_power(BOOL enable)
{
if (enable) {
LCD_CHECK_RET(LCD_PowerOn());
init_io_pad();
} else {
LCD_CHECK_RET(LCD_PowerOff());
}
return DISP_STATUS_OK;
}
static DISP_STATUS dpi_enable_power(BOOL enable)
{
if (enable) {
DPI_CHECK_RET(DPI_PowerOn());
init_mipi_pll();//for MT6573 and later chip, Must re-init mipi pll for dpi, because pll register have located in
//MMSYS1 except MT6516
init_io_pad();
LCD_CHECK_RET(LCD_PowerOn());
DPI_CHECK_RET(DPI_EnableClk());
} else {
DPI_CHECK_RET(DPI_DisableClk());
DPI_CHECK_RET(DPI_PowerOff());
LCD_CHECK_RET(LCD_PowerOff());
DPI_mipi_switch(false);
}
return DISP_STATUS_OK;
}
void Disp_IntroLcdMsgs(void){
LCD_PowerOff();
LCD_Frame1(); //make good looking frame around LCD
LCD_Setcursor(1,9);
LCD_Print(" ");
LCD_Setcursor(1,10);
LCD_DataWrite(1); //prints polltech logo that is stored at location 1
LCD_Setcursor(2,2);
LCD_Print(" Polltech ");
LCD_Setcursor(3,2);
LCD_Print(" Instruments ");
LCD_PowerOn();
delay_sec(1);
LCD_Setcursor(2,2);
LCD_Print("StackMonitoringKit");
LCD_Setcursor(3,2);
LCD_Print(" Model PEM-SMK 20 ");
delay_sec(1);
}
int disphal_process_dbg_opt(const char *opt)
{
if (0 == strncmp(opt, "dbi:", 4))
{
if (0 == strncmp(opt + 4, "on", 2)) {
LCD_PowerOn();
} else if (0 == strncmp(opt + 4, "off", 3)) {
LCD_PowerOff();
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "dpi:", 4))
{
if (0 == strncmp(opt + 4, "on", 2)) {
DPI_PowerOn();
} else if (0 == strncmp(opt + 4, "off", 3)) {
DPI_PowerOff();
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "dsi:", 4))
{
if (0 == strncmp(opt + 4, "on", 2)) {
DSI_PowerOn();
} else if (0 == strncmp(opt + 4, "off", 3)) {
DSI_PowerOff();
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "te:", 3))
{
if (0 == strncmp(opt + 3, "on", 2)) {
if (DSI_Get_EXT_TE())
{
//DISP_LOG_PRINT(ANDROID_LOG_INFO, "DSI", "EXT TE is enabled, can not enable BTA TE now\n");
}
else
{
//DISP_LOG_PRINT(ANDROID_LOG_INFO, "DSI", "Before: BTA_TE = %d, EXT_TE = %d\n", DSI_Get_BTA_TE(),DSI_Get_EXT_TE());
LCD_TE_Enable(TRUE);
DSI_TE_Enable(TRUE);
//DISP_LOG_PRINT(ANDROID_LOG_INFO, "DSI", "After : BTA_TE = %d, EXT_TE = %d\n", DSI_Get_BTA_TE(),DSI_Get_EXT_TE());
}
} else if (0 == strncmp(opt + 3, "off", 3)) {
//DISP_LOG_PRINT(ANDROID_LOG_INFO, "DSI", "Before: BTA_TE = %d, EXT_TE = %d\n", DSI_Get_BTA_TE(),DSI_Get_EXT_TE());
LCD_TE_Enable(FALSE);
DSI_TE_Enable(FALSE);
//DISP_LOG_PRINT(ANDROID_LOG_INFO, "DSI", "After : BTA_TE = %d, EXT_TE = %d\n", DSI_Get_BTA_TE(),DSI_Get_EXT_TE());
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "te_ext:", 7))
{
if (0 == strncmp(opt + 7, "on", 2)) {
if (DSI_Get_BTA_TE())
{
//DISP_LOG_PRINT(ANDROID_LOG_INFO, "DSI", "BTA TE is enabled, can not enable EXT TE now\n");
}
else
{
//DISP_LOG_PRINT(ANDROID_LOG_INFO, "DSI", "Before: BTA_TE = %d, EXT_TE = %d\n", DSI_Get_BTA_TE(),DSI_Get_EXT_TE());
LCD_TE_Enable(TRUE);
DSI_TE_EXT_Enable(TRUE);
//DISP_LOG_PRINT(ANDROID_LOG_INFO, "DSI", "After : BTA_TE = %d, EXT_TE = %d\n", DSI_Get_BTA_TE(),DSI_Get_EXT_TE());
}
} else if (0 == strncmp(opt + 7, "off", 3)) {
//DISP_LOG_PRINT(ANDROID_LOG_INFO, "DSI", "Before: BTA_TE = %d, EXT_TE = %d\n", DSI_Get_BTA_TE(),DSI_Get_EXT_TE());
LCD_TE_Enable(FALSE);
DSI_TE_EXT_Enable(FALSE);
//DISP_LOG_PRINT(ANDROID_LOG_INFO, "DSI", "After : BTA_TE = %d, EXT_TE = %d\n", DSI_Get_BTA_TE(),DSI_Get_EXT_TE());
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "reg:", 4))
{
if (0 == strncmp(opt + 4, "dpi", 3)) {
DPI_DumpRegisters();
} else if (0 == strncmp(opt + 4, "dsi", 3)) {
DSI_DumpRegisters();
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "lcdlog:", 7))
{
if (0 == strncmp(opt + 7, "on", 2)) {
dbi_log_enable(true);
} else if (0 == strncmp(opt + 7, "off", 3)) {
dbi_log_enable(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "dsilog:", 7))
{
if (0 == strncmp(opt + 7, "on", 2)) {
DSI_Enable_Log(true);
} else if (0 == strncmp(opt + 7, "off", 3)) {
DSI_Enable_Log(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "dpilog:", 7))
{
if (0 == strncmp(opt + 7, "on", 2)) {
//dpi_log_enable(true);
} else if (0 == strncmp(opt + 7, "off", 3)) {
//dpi_log_enable(false);
} else {
goto Error;
}
}
else
goto Error;
return 0;
Error:
return -1;
}
// protected by sem_early_suspend, sem_update_screen
static DISP_STATUS dsi_enable_power(BOOL enable)
{
disp_drv_dsi_init_context();
if(lcm_params->dsi.mode == CMD_MODE) {
if (enable) {
#if 0
// Switch bus to MIPI TX.
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
DSI_PHY_clk_switch(1);
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
DSI_CHECK_RET(DSI_PowerOn());
DSI_WaitForNotBusy();
DSI_clk_HS_mode(0);
DSI_clk_ULP_mode(0);
DSI_lane0_ULP_mode(0);
DSI_Reset();
LCD_CHECK_RET(LCD_PowerOn());
#else
DSI_PHY_clk_switch(1);
DSI_CHECK_RET(DSI_PowerOn());
if(Need_Wait_ULPS())
Wait_ULPS_Mode();
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
Wait_WakeUp();
LCD_CHECK_RET(LCD_PowerOn());
#endif
} else {
LCD_CHECK_RET(LCD_PowerOff());
DSI_clk_HS_mode(0);
DSI_lane0_ULP_mode(1);
DSI_clk_ULP_mode(1);
DSI_CHECK_RET(DSI_PowerOff());
DSI_PHY_clk_switch(0);
// Switch bus to GPIO, then power level will be decided by GPIO setting.
DSI_CHECK_RET(DSI_enable_MIPI_txio(FALSE));
}
} else {
#if 0
#ifndef BUILD_UBOOT
spin_lock(&g_handle_esd_lock);
#endif
#endif
if (enable) {
#if 0
// Switch bus to MIPI TX.
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
DSI_PHY_clk_switch(1);
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
DSI_CHECK_RET(DSI_PowerOn());
DSI_clk_ULP_mode(0);
DSI_lane0_ULP_mode(0);
DSI_clk_HS_mode(0);
DSI_Reset();
DPI_CHECK_RET(DPI_PowerOn());
LCD_CHECK_RET(LCD_PowerOn());
#else
DSI_PHY_clk_switch(1);
DSI_CHECK_RET(DSI_PowerOn());
if(Need_Wait_ULPS())
Wait_ULPS_Mode();
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
Wait_WakeUp();
DPI_CHECK_RET(DPI_PowerOn());
LCD_CHECK_RET(LCD_PowerOn());
#endif
} else {
#ifndef BUILD_UBOOT
dsi_vdo_streaming = false;
if(lcm_params->dsi.noncont_clock)
DSI_set_noncont_clk(false, lcm_params->dsi.noncont_clock_period);
if(lcm_params->dsi.lcm_int_te_monitor)
DSI_set_int_TE(false, lcm_params->dsi.lcm_int_te_period);
#endif
LCD_CHECK_RET(LCD_PowerOff());
DPI_CHECK_RET(DPI_PowerOff());
DSI_lane0_ULP_mode(1);
DSI_clk_ULP_mode(1);
DSI_CHECK_RET(DSI_PowerOff());
DSI_PHY_clk_switch(0);
// Switch bus to GPIO, then power level will be decided by GPIO setting.
DSI_CHECK_RET(DSI_enable_MIPI_txio(FALSE));
}
#if 0
#ifndef BUILD_UBOOT
spin_unlock(&g_handle_esd_lock);
#endif
#endif
}
return DISP_STATUS_OK;
}
LCDTFTConf::LCDTFTConf()
{
CurrentFrameBuffer = LCD_FRAME_BUFFER;
CurrentLayer = LCD_BACKGROUND_LAYER;
LTDC_InitTypeDef LTDC_InitStruct;
/* Configure the LCD Control pins ------------------------------------------*/
LCD_CtrlLinesConfig();
LCD_ChipSelect(DISABLE);
LCD_ChipSelect(ENABLE);
/* Configure the LCD_SPI interface -----------------------------------------*/
LCD_SPIConfig();
/* Power on the LCD --------------------------------------------------------*/
LCD_PowerOn();
/* Enable the LTDC Clock */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_LTDC, ENABLE);
/* Enable the DMA2D Clock */
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA2D, ENABLE);
/* Configure the LCD Control pins */
LCD_AF_GPIOConfig();
/* Configure the FMC Parallel interface : SDRAM is used as Frame Buffer for LCD */
SDRAM_Init();
/* LTDC Configuration *********************************************************/
/* Polarity configuration */
/* Initialize the horizontal synchronization polarity as active low */
LTDC_InitStruct.LTDC_HSPolarity = LTDC_HSPolarity_AL;
/* Initialize the vertical synchronization polarity as active low */
LTDC_InitStruct.LTDC_VSPolarity = LTDC_VSPolarity_AL;
/* Initialize the data enable polarity as active low */
LTDC_InitStruct.LTDC_DEPolarity = LTDC_DEPolarity_AL;
/* Initialize the pixel clock polarity as input pixel clock */
LTDC_InitStruct.LTDC_PCPolarity = LTDC_PCPolarity_IPC;
/* Configure R,G,B component values for LCD background color */
LTDC_InitStruct.LTDC_BackgroundRedValue = 0;
LTDC_InitStruct.LTDC_BackgroundGreenValue = 0;
LTDC_InitStruct.LTDC_BackgroundBlueValue = 0;
/* Configure PLLSAI prescalers for LCD */
/* Enable Pixel Clock */
/* PLLSAI_VCO Input = HSE_VALUE/PLL_M = 1 Mhz */
/* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAI_N = 192 Mhz */
/* PLLLCDCLK = PLLSAI_VCO Output/PLLSAI_R = 192/4 = 48 Mhz */
/* LTDC clock frequency = PLLLCDCLK / RCC_PLLSAIDivR = 48/8 = 6 Mhz */
RCC_PLLSAIConfig(192, 7, 4);
RCC_LTDCCLKDivConfig(RCC_PLLSAIDivR_Div8);
/* Enable PLLSAI Clock */
RCC_PLLSAICmd(ENABLE);
/* Wait for PLLSAI activation */
while(RCC_GetFlagStatus(RCC_FLAG_PLLSAIRDY) == RESET);
/* Timing configuration */
/* Configure horizontal synchronization width */
LTDC_InitStruct.LTDC_HorizontalSync = 9;
/* Configure vertical synchronization height */
LTDC_InitStruct.LTDC_VerticalSync = 1;
/* Configure accumulated horizontal back porch */
LTDC_InitStruct.LTDC_AccumulatedHBP = 29;
/* Configure accumulated vertical back porch */
LTDC_InitStruct.LTDC_AccumulatedVBP = 3;
/* Configure accumulated active width */
LTDC_InitStruct.LTDC_AccumulatedActiveW = 269;
/* Configure accumulated active height */
LTDC_InitStruct.LTDC_AccumulatedActiveH = 323;
/* Configure total width */
LTDC_InitStruct.LTDC_TotalWidth = 279;
/* Configure total height */
LTDC_InitStruct.LTDC_TotalHeigh = 327;
LTDC_Init(<DC_InitStruct);
LCD_LayerInit();
/* LTDC reload configuration */
LTDC_ReloadConfig(LTDC_IMReload);
/* Enable the LTDC */
LTDC_Cmd(ENABLE);
}
// protected by sem_early_suspend, sem_update_screen
static DISP_STATUS dsi_enable_power(BOOL enable)
{
disp_drv_dsi_init_context();
if(lcm_params->dsi.mode == CMD_MODE) {
if (enable) {
#if 0
// Switch bus to MIPI TX.
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
DSI_PHY_clk_switch(TRUE, lcm_params);
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
DSI_CHECK_RET(DSI_PowerOn());
DSI_WaitForNotBusy();
DSI_clk_HS_mode(0);
DSI_clk_ULP_mode(0);
DSI_lane0_ULP_mode(0);
DSI_Reset();
LCD_CHECK_RET(LCD_PowerOn());
#else
#ifndef MT65XX_NEW_DISP
DSI_PHY_clk_switch(TRUE, lcm_params);
DSI_CHECK_RET(DSI_PowerOn());
if(Need_Wait_ULPS())
Wait_ULPS_Mode();
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
#else
// enable MMSYS CG
DSI_CHECK_RET(DSI_PowerOn());
// initialize clock setting
DSI_PHY_clk_setting(lcm_params);
// initialize dsi timing
DSI_PHY_TIMCONFIG(lcm_params);
// restore dsi register
DSI_CHECK_RET(DSI_RestoreRegisters());
// enable sleep-out mode
DSI_CHECK_RET(DSI_SleepOut());
// enter HS mode
DSI_PHY_clk_switch(TRUE, lcm_params);
// enter wakeup
DSI_CHECK_RET(DSI_Wakeup());
// enable clock
DSI_CHECK_RET(DSI_EnableClk());
// engine reset
DSI_Reset();
#endif
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
#ifndef MT65XX_NEW_DISP
Wait_WakeUp();
#endif
#endif
}
else {
// backup dsi register
DSI_CHECK_RET(DSI_WaitForEngineNotBusy());
DSI_CHECK_RET(DSI_BackupRegisters());
// enter ULPS mode
DSI_clk_ULP_mode(1);
DSI_lane0_ULP_mode(1);
mdelay(1);
// disable engine clock
DSI_CHECK_RET(DSI_DisableClk());
// disable CG
DSI_CHECK_RET(DSI_PowerOff());
// disable mipi pll
DSI_PHY_clk_switch(FALSE, lcm_params);
// Switch bus to GPIO, then power level will be decided by GPIO setting.
DSI_CHECK_RET(DSI_enable_MIPI_txio(FALSE));
}
}
else {
if (enable) {
#if 0
// Switch bus to MIPI TX.
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
DSI_PHY_clk_switch(TRUE, lcm_params);
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
DSI_CHECK_RET(DSI_PowerOn());
DSI_clk_ULP_mode(0);
DSI_lane0_ULP_mode(0);
DSI_clk_HS_mode(0);
DSI_Reset();
DPI_CHECK_RET(DPI_PowerOn());
LCD_CHECK_RET(LCD_PowerOn());
#else
#ifndef MT65XX_NEW_DISP
DSI_PHY_clk_switch(TRUE, lcm_params);
DSI_CHECK_RET(DSI_PowerOn());
if(Need_Wait_ULPS())
Wait_ULPS_Mode();
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
#else
needStartDSI = true;
// enable MMSYS CG
DSI_CHECK_RET(DSI_PowerOn());
// initialize clock setting
DSI_PHY_clk_setting(lcm_params);
// initialize dsi timing
DSI_PHY_TIMCONFIG(lcm_params);
// restore dsi register
DSI_CHECK_RET(DSI_RestoreRegisters());
// enable sleep-out mode
DSI_CHECK_RET(DSI_SleepOut());
// enter HS mode
DSI_PHY_clk_switch(TRUE, lcm_params);
// enter wakeup
DSI_CHECK_RET(DSI_Wakeup());
// enable clock
DSI_CHECK_RET(DSI_EnableClk());
// engine reset
DSI_Reset();
#endif
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
#ifndef MT65XX_NEW_DISP
Wait_WakeUp();
#endif
#endif
}
else {
#ifndef BUILD_UBOOT
is_video_mode_running = false;
if(lcm_params->dsi.noncont_clock)
DSI_set_noncont_clk(false, lcm_params->dsi.noncont_clock_period);
if(lcm_params->dsi.lcm_int_te_monitor)
DSI_set_int_TE(false, lcm_params->dsi.lcm_int_te_period);
#endif
// backup dsi register
DSI_CHECK_RET(DSI_WaitForEngineNotBusy());
DSI_CHECK_RET(DSI_BackupRegisters());
// enter ULPS mode
DSI_clk_ULP_mode(1);
DSI_lane0_ULP_mode(1);
mdelay(1);
// disable engine clock
DSI_CHECK_RET(DSI_DisableClk());
// disable CG
DSI_CHECK_RET(DSI_PowerOff());
// disable mipi pll
DSI_PHY_clk_switch(FALSE, lcm_params);
// Switch bus to GPIO, then power level will be decided by GPIO setting.
DSI_CHECK_RET(DSI_enable_MIPI_txio(FALSE));
}
}
return DISP_STATUS_OK;
}
static void LCD_Config(void)
{
LTDC_InitTypeDef LTDC_InitStruct;
LTDC_Layer_InitTypeDef LTDC_Layer_InitStruct;
GPIO_InitTypeDef GPIO_InitStructure;
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD, ENABLE);
/* Configure NCS in Output Push-Pull mode */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
GPIO_Init(GPIOD, &GPIO_InitStructure);
/* Configure the LCD Control pins ------------------------------------------*/
LCD_CtrlLinesConfig();
LCD_ChipSelect(DISABLE);
LCD_ChipSelect(ENABLE);
/* Configure the LCD_SPI interface -----------------------------------------*/
LCD_SPIConfig();
/* Power on the LCD --------------------------------------------------------*/
LCD_PowerOn();
/* Enable the LTDC Clock */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_LTDC, ENABLE);
/* Enable the DMA2D Clock */
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA2D, ENABLE);
/* Configure the LCD Control pins */
LCD_AF_GPIOConfig();
/* Configure the FMC Parallel interface : SDRAM is used as Frame Buffer for LCD */
SDRAM_Init();
/* Enable Pixel Clock --------------------------------------------------------*/
/* Configure PLLSAI prescalers for LCD */
/* PLLSAI_VCO Input = HSE_VALUE/PLL_M = 1 Mhz */
/* PLLSAI_VCO Output = PLLSAI_VCO Input * PLLSAI_N = 192 Mhz */
/* PLLLCDCLK = PLLSAI_VCO Output/PLLSAI_R = 192/3 = 64 Mhz */
/* LTDC clock frequency = PLLLCDCLK / RCC_PLLSAIDivR = 64/8 = 8 Mhz */
RCC_PLLSAIConfig(192, 7, 3);
RCC_LTDCCLKDivConfig(RCC_PLLSAIDivR_Div8);
/* Enable PLLSAI Clock */
RCC_PLLSAICmd(ENABLE);
/* Wait for PLLSAI activation */
while(RCC_GetFlagStatus(RCC_FLAG_PLLSAIRDY) == RESET)
{
}
/* LTDC Initialization -------------------------------------------------------*/
/* Initialize the horizontal synchronization polarity as active low*/
LTDC_InitStruct.LTDC_HSPolarity = LTDC_HSPolarity_AL;
/* Initialize the vertical synchronization polarity as active low */
LTDC_InitStruct.LTDC_VSPolarity = LTDC_VSPolarity_AL;
/* Initialize the data enable polarity as active low */
LTDC_InitStruct.LTDC_DEPolarity = LTDC_DEPolarity_AL;
/* Initialize the pixel clock polarity as input pixel clock */
LTDC_InitStruct.LTDC_PCPolarity = LTDC_PCPolarity_IPC;
/* Timing configuration */
/* Configure horizontal synchronization width */
LTDC_InitStruct.LTDC_HorizontalSync = 9;
/* Configure vertical synchronization height */
LTDC_InitStruct.LTDC_VerticalSync = 1;
/* Configure accumulated horizontal back porch */
LTDC_InitStruct.LTDC_AccumulatedHBP = 29;
/* Configure accumulated vertical back porch */
LTDC_InitStruct.LTDC_AccumulatedVBP = 3;
/* Configure accumulated active width */
LTDC_InitStruct.LTDC_AccumulatedActiveW = 269;
/* Configure accumulated active height */
LTDC_InitStruct.LTDC_AccumulatedActiveH = 323;
/* Configure total width */
LTDC_InitStruct.LTDC_TotalWidth = 279;
/* Configure total height */
LTDC_InitStruct.LTDC_TotalHeigh = 327;
LTDC_Init(<DC_InitStruct);
/* Configure R,G,B component values for LCD background color */
LTDC_InitStruct.LTDC_BackgroundRedValue = 0;
LTDC_InitStruct.LTDC_BackgroundGreenValue = 0;
LTDC_InitStruct.LTDC_BackgroundBlueValue = 0;
LTDC_Init(<DC_InitStruct);
/* LTDC initialization end ---------------------------------------------------*/
/* Layer1 Configuration ------------------------------------------------------*/
/* Windowing configuration */
/* In this case all the active display area is used to display a picture then :
Horizontal start = horizontal synchronization + Horizontal back porch = 30
Horizontal stop = Horizontal start + window width -1 = 30 + 240 -1
Vertical start = vertical synchronization + vertical back porch = 4
Vertical stop = Vertical start + window height -1 = 4 + 320 -1 */
LTDC_Layer_InitStruct.LTDC_HorizontalStart = 30;
LTDC_Layer_InitStruct.LTDC_HorizontalStop = (240 + 30 - 1);
LTDC_Layer_InitStruct.LTDC_VerticalStart = 4;
LTDC_Layer_InitStruct.LTDC_VerticalStop = (320 + 4 - 1);
/* Pixel Format configuration*/
LTDC_Layer_InitStruct.LTDC_PixelFormat = LTDC_Pixelformat_RGB565;
/* Alpha constant (255 totally opaque) */
LTDC_Layer_InitStruct.LTDC_ConstantAlpha = 255;
/* Configure blending factors */
LTDC_Layer_InitStruct.LTDC_BlendingFactor_1 = LTDC_BlendingFactor1_CA;
LTDC_Layer_InitStruct.LTDC_BlendingFactor_2 = LTDC_BlendingFactor2_CA;
/* Default Color configuration (configure A,R,G,B component values) */
LTDC_Layer_InitStruct.LTDC_DefaultColorBlue = 0;
LTDC_Layer_InitStruct.LTDC_DefaultColorGreen = 0;
LTDC_Layer_InitStruct.LTDC_DefaultColorRed = 0;
LTDC_Layer_InitStruct.LTDC_DefaultColorAlpha = 0;
/* Input Address configuration */
LTDC_Layer_InitStruct.LTDC_CFBStartAdress = (uint32_t)&RGB565_240x320;
/* the length of one line of pixels in bytes + 3 then :
Line Lenth = Active high width x number of bytes per pixel + 3
Active high width = 240
number of bytes per pixel = 2 (pixel_format : RGB565)
*/
LTDC_Layer_InitStruct.LTDC_CFBLineLength = ((240 * 2) + 3);
/* the pitch is the increment from the start of one line of pixels to the
start of the next line in bytes, then :
Pitch = Active high width x number of bytes per pixel
*/
LTDC_Layer_InitStruct.LTDC_CFBPitch = (240 * 2);
/* configure the number of lines */
LTDC_Layer_InitStruct.LTDC_CFBLineNumber = 320;
LTDC_LayerInit(LTDC_Layer1, <DC_Layer_InitStruct);
LTDC_DitherCmd(ENABLE);
}
static void process_dbg_opt(const char *opt)
{
if (0 == strncmp(opt, "hdmion", 6))
{
hdmi_force_init();
}
else if (0 == strncmp(opt, "fps:", 4))
{
if (0 == strncmp(opt + 4, "on", 2)) {
dbg_opt.en_fps_log = 1;
} else if (0 == strncmp(opt + 4, "off", 3)) {
dbg_opt.en_fps_log = 0;
} else {
goto Error;
}
reset_fps_logger();
}
else if (0 == strncmp(opt, "tl:", 3))
{
if (0 == strncmp(opt + 3, "on", 2)) {
dbg_opt.en_touch_latency_log = 1;
} else if (0 == strncmp(opt + 3, "off", 3)) {
dbg_opt.en_touch_latency_log = 0;
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "black", 5))
{
mtkfb_clear_lcm();
}
else if (0 == strncmp(opt, "suspend", 4))
{
DISP_PanelEnable(FALSE);
DISP_PowerEnable(FALSE);
}
else if (0 == strncmp(opt, "resume", 4))
{
DISP_PowerEnable(TRUE);
DISP_PanelEnable(TRUE);
}
else if (0 == strncmp(opt, "lcm:", 4))
{
if (0 == strncmp(opt + 4, "on", 2)) {
DISP_PanelEnable(TRUE);
} else if (0 == strncmp(opt + 4, "off", 3)) {
DISP_PanelEnable(FALSE);
}
else if (0 == strncmp(opt + 4, "init", 4)) {
if (NULL != lcm_drv && NULL != lcm_drv->init) {
lcm_drv->init();
}
}else {
goto Error;
}
}
else if (0 == strncmp(opt, "cabc:", 5))
{
if (0 == strncmp(opt + 5, "ui", 2)) {
mtkfb_set_backlight_mode(1);
}else if (0 == strncmp(opt + 5, "mov", 3)) {
mtkfb_set_backlight_mode(3);
}else if (0 == strncmp(opt + 5, "still", 5)) {
mtkfb_set_backlight_mode(2);
}else {
goto Error;
}
}
else if (0 == strncmp(opt, "lcd:", 4))
{
if (0 == strncmp(opt + 4, "on", 2)) {
DISP_PowerEnable(TRUE);
} else if (0 == strncmp(opt + 4, "off", 3)) {
DISP_PowerEnable(FALSE);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "dbi:", 4))
{
if (0 == strncmp(opt + 4, "on", 2)) {
LCD_PowerOn();
} else if (0 == strncmp(opt + 4, "off", 3)) {
LCD_PowerOff();
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "dpi:", 4))
{
if (0 == strncmp(opt + 4, "on", 2)) {
DPI_PowerOn();
} else if (0 == strncmp(opt + 4, "off", 3)) {
DPI_PowerOff();
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "dsi:", 4))
{
if (0 == strncmp(opt + 4, "on", 2)) {
DSI_PowerOn();
} else if (0 == strncmp(opt + 4, "off", 3)) {
DSI_PowerOff();
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "te:", 3))
{
if (0 == strncmp(opt + 3, "on", 2)) {
LCD_TE_Enable(TRUE);
DSI_TE_Enable(TRUE);
} else if (0 == strncmp(opt + 3, "off", 3)) {
LCD_TE_Enable(FALSE);
DSI_TE_Enable(FALSE);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "vsynclog:", 9))
{
if (0 == strncmp(opt + 9, "on", 2))
{
EnableVSyncLog = 1;
} else if (0 == strncmp(opt + 9, "off", 3))
{
EnableVSyncLog = 0;
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "layer", 5))
{
dump_lcd_layer_info();
}
else if (0 == strncmp(opt, "reg:", 4))
{
if (0 == strncmp(opt + 4, "lcd", 3)) {
LCD_DumpRegisters();
}else if (0 == strncmp(opt + 4, "dpi1", 4)) {
DPI1_DumpRegisters();
}else if (0 == strncmp(opt + 4, "dpi", 3)) {
DPI_DumpRegisters();
} else if (0 == strncmp(opt + 4, "dsi", 3)) {
DSI_DumpRegisters();
#if defined(MTK_TVOUT_SUPPORT)
} else if (0 == strncmp(opt + 4, "tvc", 3)) {
TVC_DumpRegisters();
} else if (0 == strncmp(opt + 4, "tve", 3)) {
TVE_DumpRegisters();
} else if (0 == strncmp(opt + 4, "tvr", 3)) {
TVR_DumpRegisters();
#endif
} else {
goto Error;
}
}
#if defined(MTK_TVOUT_SUPPORT)
else if (0 == strncmp(opt, "tv:", 3))
{
if (0 == strncmp(opt + 3, "on", 2)) {
TVOUT_TvCablePlugIn();
} else if (0 == strncmp(opt +3, "off", 3)) {
TVOUT_TvCablePlugOut();
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "tvforce:", 8))
{
if (0 == strncmp(opt + 8, "on", 2)) {
TVOUT_TvCablePlugIn_Directly();
} else if (0 == strncmp(opt +8, "off", 3)) {
TVOUT_TvCablePlugOut_Directly();
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "tvsys:", 6))
{
if (0 == strncmp(opt + 6, "ntsc", 4)) {
TVOUT_SetTvSystem(TVOUT_SYSTEM_NTSC);
} else if (0 == strncmp(opt + 6, "pal", 3)) {
TVOUT_SetTvSystem(TVOUT_SYSTEM_PAL);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "tvrot:", 6))
{
if (0 == strncmp(opt + 6, "on", 2)) {
TVOUT_SetOrientation(TVOUT_ROT_270);
} else if (0 == strncmp(opt + 6, "off", 3)) {
TVOUT_SetOrientation(TVOUT_ROT_0);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "tvcb:", 5))
{
if (0 == strncmp(opt + 5, "on", 2)) {
TVOUT_EnableColorBar(TRUE);
} else if (0 == strncmp(opt + 5, "off", 3)) {
TVOUT_EnableColorBar(FALSE);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "tvvm:", 5))
{
if (0 == strncmp(opt + 5, "on", 2)) {
TVOUT_DisableVideoMode(false);
} else if (0 == strncmp(opt + 5, "off", 3)) {
TVOUT_DisableVideoMode(true);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "tvlog:", 6))
{
if (0 == strncmp(opt + 6, "on", 2)) {
TVOUT_EnableLog(true);
} else if (0 == strncmp(opt + 6, "off", 3)) {
TVOUT_EnableLog(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "tvtime:", 7))
{
if (0 == strncmp(opt + 7, "on", 2)) {
TVOUT_EnableTimeProfiling(true);
} else if (0 == strncmp(opt + 7, "off", 3)) {
TVOUT_EnableTimeProfiling(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "tvcap:", 6))
{
if (0 == strncmp(opt + 6, "on", 2)) {
capture_tv_buffer = true;
} else if (0 == strncmp(opt + 6, "off", 3)) {
capture_tv_buffer = false;
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "tvcam:", 6))
{
if (0 == strncmp(opt + 6, "on", 2)) {
TVOUT_ForceClose();
} else if (0 == strncmp(opt + 6, "off", 3)) {
TVOUT_RestoreOpen();
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "tvuser:"******"on", 2)) {
TVOUT_TurnOn(true);
} else if (0 == strncmp(opt + 7, "off", 3)) {
TVOUT_TurnOn(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "tvcoffset:", 10))
{
char *p = (char *)opt + 10;
unsigned long offset = simple_strtoul(p, &p, 10);
TVC_SetCheckLineOffset(offset);
}
#endif
else if (0 == strncmp(opt, "regw:", 5))
{
char *p = (char *)opt + 5;
unsigned long addr = simple_strtoul(p, &p, 16);
unsigned long val = simple_strtoul(p + 1, &p, 16);
if (addr) {
OUTREG32(addr, val);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "regr:", 5))
{
char *p = (char *)opt + 5;
unsigned int addr = (unsigned int) simple_strtoul(p, &p, 16);
if (addr) {
DISP_LOG_PRINT(ANDROID_LOG_INFO, "DBG", "Read register 0x%08x: 0x%08x\n", addr, INREG32(addr));
} else {
goto Error;
}
}
else if(0 == strncmp(opt, "bkl:", 4))
{
char *p = (char *)opt + 4;
unsigned int level = (unsigned int) simple_strtoul(p, &p, 10);
DISP_LOG_PRINT(ANDROID_LOG_INFO, "DBG", "process_dbg_opt(), set backlight level = %d\n", level);
DISP_SetBacklight(level);
}
else if(0 == strncmp(opt, "dither:", 7))
{
unsigned lrs, lgs, lbs, dbr, dbg, dbb;
char *p = (char *)opt + 7;
lrs = (unsigned int) simple_strtoul(p, &p, 16);
p++;
lgs = (unsigned int) simple_strtoul(p, &p, 16);
p++;
lbs = (unsigned int) simple_strtoul(p, &p, 16);
p++;
dbr = (unsigned int) simple_strtoul(p, &p, 16);
p++;
dbg = (unsigned int) simple_strtoul(p, &p, 16);
p++;
dbb = (unsigned int) simple_strtoul(p, &p, 16);
DISP_LOG_PRINT(ANDROID_LOG_INFO, "DBG", "process_dbg_opt(), %d %d %d %d %d %d\n", lrs, lgs, lbs, dbr, dbg, dbb);
#if 0 //defined(CONFIG_ARCH_MT6573)
LCD_WaitForNotBusy();
LCD_ConfigDither(lrs, lgs, lbs, dbr, dbg, dbb);
LCD_StartTransfer(true);
#endif
}
else if (0 == strncmp(opt, "mtkfblog:", 9))
{
if (0 == strncmp(opt + 9, "on", 2)) {
mtkfb_log_enable(true);
} else if (0 == strncmp(opt + 9, "off", 3)) {
mtkfb_log_enable(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "displog:", 8))
{
if (0 == strncmp(opt + 8, "on", 2)) {
disp_log_enable(true);
} else if (0 == strncmp(opt + 8, "off", 3)) {
disp_log_enable(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "lcdlog:", 7))
{
if (0 == strncmp(opt + 7, "on", 2)) {
dbi_log_enable(true);
} else if (0 == strncmp(opt + 7, "off", 3)) {
dbi_log_enable(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "dsilog:", 7))
{
if (0 == strncmp(opt + 7, "on", 2)) {
DSI_Enable_Log(true);
} else if (0 == strncmp(opt + 7, "off", 3)) {
DSI_Enable_Log(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "glitchlog:", 10))
{
if (0 == strncmp(opt + 10, "on", 2)) {
Glitch_Enable_Log(true);
} else if (0 == strncmp(opt + 10, "off", 3)) {
Glitch_Enable_Log(false);
} else {
goto Error;
}
}
else if(0 == strncmp(opt, "glitch_times:", 13))
{
char *p = (char *)opt + 13;
unsigned int level = (unsigned int) simple_strtoul(p, &p, 10);
Glitch_times(level);
}
else if (0 == strncmp(opt, "mtkfb_vsynclog:", 15))
{
if (0 == strncmp(opt + 15, "on", 2)) {
mtkfb_vsync_log_enable(true);
} else if (0 == strncmp(opt + 15, "off", 3)) {
mtkfb_vsync_log_enable(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "dpilog:", 7))
{
if (0 == strncmp(opt + 7, "on", 2)) {
//dpi_log_enable(true);
} else if (0 == strncmp(opt + 7, "off", 3)) {
//dpi_log_enable(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "log:", 4))
{
if (0 == strncmp(opt + 4, "on", 2)) {
mtkfb_log_enable(true);
disp_log_enable(true);
dbi_log_enable(true);
//dpi_log_enable(true);
} else if (0 == strncmp(opt + 4, "off", 3)) {
mtkfb_log_enable(false);
disp_log_enable(false);
dbi_log_enable(false);
//dpi_log_enable(false);
} else {
goto Error;
}
}
else if (0 == strncmp(opt, "update", 6))
{
DISP_UpdateScreen(0, 0, DISP_GetScreenWidth(), DISP_GetScreenHeight());
}
else if (0 == strncmp(opt, "pan_disp", 8))
{
mtkfb_pan_disp_test();
}
else if (0 == strncmp(opt, "sem_cnt", 7))
{
mtkfb_show_sem_cnt();
LCD_GetVsyncCnt();
}
else if (0 == strncmp(opt, "hang:", 5))
{
if (0 == strncmp(opt + 5, "on", 2)) {
mtkfb_hang_test(true);
} else if (0 == strncmp(opt + 5, "off", 3)) {
mtkfb_hang_test(false);
} else{
goto Error;
}
}
#if defined(MTK_M4U_SUPPORT)
else if (0 == strncmp(opt, "m4u:", 4))
{
if (0 == strncmp(opt + 4, "on", 2)) {
mtkfb_m4u_switch(true);
} else if (0 == strncmp(opt + 4, "off", 3)) {
mtkfb_m4u_switch(false);
} else if (0 == strncmp(opt + 4, "dump", 4)) {
mtkfb_m4u_dump();
} else{
goto Error;
}
}
#endif
else if (0 == strncmp(opt, "cpfbonly:", 9))
{
if (0 == strncmp(opt + 9, "on", 2))
{
mtkfb_capture_fb_only(true);
}
else if (0 == strncmp(opt + 9, "off", 3))
{
mtkfb_capture_fb_only(false);
}
}
else if (0 == strncmp(opt, "esd:", 4))
{
if (0 == strncmp(opt + 4, "on", 2))
{
esd_recovery_pause(FALSE);
}
else if (0 == strncmp(opt + 4, "off", 3))
{
esd_recovery_pause(TRUE);
}
}
else if (0 == strncmp(opt, "HQA:", 4))
{
if (0 == strncmp(opt + 4, "NormalToFactory", 15))
{
mtkfb_switch_normal_to_factory();
}
else if (0 == strncmp(opt + 4, "FactoryToNormal", 15))
{
mtkfb_switch_factory_to_normal();
}
}
else if (0 == strncmp(opt, "mmp", 3))
{
init_mtkfb_mmp_events();
}
else if (0 == strncmp(opt, "dump_layer:", 11))
{
if (0 == strncmp(opt + 11, "on", 2))
{
char *p = (char *)opt + 14;
gCaptureLayerDownX = simple_strtoul(p, &p, 10);
gCaptureLayerDownY = simple_strtoul(p+1, &p, 10);
gCaptureLayerEnable = 1;
}
else if (0 == strncmp(opt + 11, "off", 3))
{
gCaptureLayerEnable = 0;
}
}
else if (0 == strncmp(opt, "dump_ovl:", 9))
{
if (0 == strncmp(opt + 9, "on", 2))
{
char *p = (char *)opt + 12;
gCaptureOvlDownX = simple_strtoul(p, &p, 10);
gCaptureOvlDownY = simple_strtoul(p+1, &p, 10);
gCaptureOvlThreadEnable = 1;
wake_up_process(captureovl_task);
}
else if (0 == strncmp(opt + 9, "off", 3))
{
gCaptureOvlThreadEnable = 0;
}
}
else if (0 == strncmp(opt, "dump_fb:", 8))
{
if (0 == strncmp(opt + 8, "on", 2))
{
char *p = (char *)opt + 11;
gCaptureFBDownX = simple_strtoul(p, &p, 10);
gCaptureFBDownY = simple_strtoul(p+1, &p, 10);
gCaptureFBPeriod = simple_strtoul(p+1, &p, 10);
gCaptureFBEnable = 1;
wake_up_interruptible(&gCaptureFBWQ);
}
else if (0 == strncmp(opt + 8, "off", 3))
{
gCaptureFBEnable = 0;
}
}
else
{
goto Error;
}
return;
Error:
DISP_LOG_PRINT(ANDROID_LOG_INFO, "ERROR", "parse command error!\n\n%s", STR_HELP);
}
// protected by sem_early_suspend, sem_update_screen
static DISP_STATUS dsi_enable_power(BOOL enable)
{
disp_drv_dsi_init_context();
if(lcm_params->dsi.mode == CMD_MODE) {
if (enable) {
#if 0
// Switch bus to MIPI TX.
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
DSI_PHY_clk_switch(1);
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
DSI_CHECK_RET(DSI_PowerOn());
DSI_WaitForNotBusy();
DSI_clk_HS_mode(0);
DSI_clk_ULP_mode(0);
DSI_lane0_ULP_mode(0);
DSI_Reset();
LCD_CHECK_RET(LCD_PowerOn());
#else
DSI_PHY_clk_switch(1);
#ifndef MT65XX_NEW_DISP
DSI_CHECK_RET(DSI_PowerOn());
if(Need_Wait_ULPS())
Wait_ULPS_Mode();
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
#else
if(lcm_params->dsi.pll_select == 1)
{
ASSERT(0 == enable_pll(LVDSPLL,"mtk_dsi"));
}
DSI_PHY_clk_setting(lcm_params);
DSI_CHECK_RET(DSI_PowerOn());
DSI_clk_ULP_mode(0);
DSI_lane0_ULP_mode(0);
// DSI_clk_HS_mode(1);
#endif
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
#ifndef MT65XX_NEW_DISP
Wait_WakeUp();
LCD_CHECK_RET(LCD_PowerOn());
#endif
#endif
} else {
#ifndef MT65XX_NEW_DISP
LCD_CHECK_RET(LCD_PowerOff());
#endif
DSI_clk_HS_mode(0);
DSI_lane0_ULP_mode(1);
DSI_clk_ULP_mode(1);
// DSI_CHECK_RET(DSI_PowerOff());
DSI_PHY_clk_switch(0);
DSI_CHECK_RET(DSI_PowerOff());
// Switch bus to GPIO, then power level will be decided by GPIO setting.
DSI_CHECK_RET(DSI_enable_MIPI_txio(FALSE));
if(lcm_params->dsi.pll_select == 1)
ASSERT(0 == disable_pll(LVDSPLL,"mtk_dsi"));
}
} else {
if (enable) {
#if 0
// Switch bus to MIPI TX.
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
DSI_PHY_clk_switch(1);
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
DSI_CHECK_RET(DSI_PowerOn());
DSI_clk_ULP_mode(0);
DSI_lane0_ULP_mode(0);
DSI_clk_HS_mode(0);
DSI_Reset();
DPI_CHECK_RET(DPI_PowerOn());
LCD_CHECK_RET(LCD_PowerOn());
#else
DSI_PHY_clk_switch(1);
#ifndef MT65XX_NEW_DISP
DSI_CHECK_RET(DSI_PowerOn());
if(Need_Wait_ULPS())
Wait_ULPS_Mode();
DSI_PHY_clk_setting(lcm_params->dsi.pll_div1, lcm_params->dsi.pll_div2, lcm_params->dsi.LANE_NUM);
#else
needStartDSI = true;
if(lcm_params->dsi.pll_select == 1)
{
ASSERT(0 == enable_pll(LVDSPLL,"mtk_dsi"));
}
DSI_PHY_clk_setting(lcm_params);
DSI_CHECK_RET(DSI_PowerOn());
DSI_clk_ULP_mode(0);
DSI_lane0_ULP_mode(0);
DSI_clk_HS_mode(0);
#endif
DSI_CHECK_RET(DSI_enable_MIPI_txio(TRUE));
#ifndef MT65XX_NEW_DISP
Wait_WakeUp();
DPI_CHECK_RET(DPI_PowerOn());
LCD_CHECK_RET(LCD_PowerOn());
#endif
#endif
} else {
#ifndef BUILD_UBOOT
is_video_mode_running = false;
#ifndef MT65XX_NEW_DISP
if(lcm_params->dsi.noncont_clock)
DSI_set_noncont_clk(false, lcm_params->dsi.noncont_clock_period);
if(lcm_params->dsi.lcm_int_te_monitor)
DSI_set_int_TE(false, lcm_params->dsi.lcm_int_te_period);
#endif
#endif
#ifndef MT65XX_NEW_DISP
LCD_CHECK_RET(LCD_PowerOff());
DPI_CHECK_RET(DPI_PowerOff());
#endif
#if 1
DSI_lane0_ULP_mode(1);
DSI_clk_ULP_mode(1);
DSI_CHECK_RET(DSI_PowerOff());
#endif
DSI_PHY_clk_switch(0);
// Switch bus to GPIO, then power level will be decided by GPIO setting.
DSI_CHECK_RET(DSI_enable_MIPI_txio(FALSE));
if(lcm_params->dsi.pll_select == 1)
ASSERT(0 == disable_pll(LVDSPLL,"mtk_dsi"));
}
}
return DISP_STATUS_OK;
}
