/**
* @brief Return DSI clock frequency
* @param DSIxSource This parameter can be one of the following values:
* @arg @ref LL_RCC_DSI_CLKSOURCE
* @retval DSI clock frequency (in Hz)
* - @ref LL_RCC_PERIPH_FREQUENCY_NO indicates that oscillator is not ready
* - @ref LL_RCC_PERIPH_FREQUENCY_NA indicates that external clock is used
*/
uint32_t LL_RCC_GetDSIClockFreq(uint32_t DSIxSource)
{
uint32_t dsi_frequency = LL_RCC_PERIPH_FREQUENCY_NO;
/* Check parameter */
assert_param(IS_LL_RCC_DSI_CLKSOURCE(DSIxSource));
/* DSICLK clock frequency */
switch (LL_RCC_GetDSIClockSource(DSIxSource))
{
case LL_RCC_DSI_CLKSOURCE_PLL: /* DSI Clock is PLL Osc. */
if (LL_RCC_PLL_IsReady())
{
dsi_frequency = RCC_PLL_GetFreqDomain_DSI();
}
break;
case LL_RCC_DSI_CLKSOURCE_PHY: /* DSI Clock is DSI physical clock. */
default:
dsi_frequency = LL_RCC_PERIPH_FREQUENCY_NA;
break;
}
return dsi_frequency;
}
/**
* @brief Return USBx clock frequency
* @param USBxSource This parameter can be one of the following values:
* @arg @ref LL_RCC_USB_CLKSOURCE
* @retval USB clock frequency (in Hz)
* @arg @ref LL_RCC_PERIPH_FREQUENCY_NO indicates that oscillator (HSI48) or PLL is not ready
* @arg @ref LL_RCC_PERIPH_FREQUENCY_NA indicates that no clock source selected
*/
uint32_t LL_RCC_GetUSBClockFreq(uint32_t USBxSource)
{
uint32_t usb_frequency = LL_RCC_PERIPH_FREQUENCY_NO;
/* Check parameter */
assert_param(IS_LL_RCC_USB_CLKSOURCE(USBxSource));
/* USBCLK clock frequency */
switch (LL_RCC_GetUSBClockSource(USBxSource))
{
case LL_RCC_USB_CLKSOURCE_PLL: /* PLL clock used as USB clock source */
if (LL_RCC_PLL_IsReady())
{
usb_frequency = RCC_PLL_GetFreqDomain_SYS();
}
break;
case LL_RCC_USB_CLKSOURCE_HSI48: /* HSI48 clock used as USB clock source */
default:
if (LL_RCC_HSI48_IsReady())
{
usb_frequency = HSI48_VALUE;
}
break;
}
return usb_frequency;
}
/**
* @brief Return RNGx clock frequency
* @param RNGxSource This parameter can be one of the following values:
* @arg @ref LL_RCC_RNG_CLKSOURCE
* @retval RNG clock frequency (in Hz)
* - @ref LL_RCC_PERIPH_FREQUENCY_NO indicates that oscillator is not ready
*/
uint32_t LL_RCC_GetRNGClockFreq(uint32_t RNGxSource)
{
uint32_t rng_frequency = LL_RCC_PERIPH_FREQUENCY_NO;
/* Check parameter */
assert_param(IS_LL_RCC_RNG_CLKSOURCE(RNGxSource));
/* RNGCLK clock frequency */
switch (LL_RCC_GetRNGClockSource(RNGxSource))
{
case LL_RCC_RNG_CLKSOURCE_PLL: /* PLL clock used as RNG clock source */
if (LL_RCC_PLL_IsReady())
{
rng_frequency = RCC_PLL_GetFreqDomain_48M();
}
break;
case LL_RCC_RNG_CLKSOURCE_PLLSAI: /* PLLSAI clock used as RNG clock source */
default:
if (LL_RCC_PLLSAI_IsReady())
{
rng_frequency = RCC_PLLSAI_GetFreqDomain_48M();
}
break;
}
return rng_frequency;
}
/**
* @brief Reset the RCC clock configuration to the default reset state.
* @note The default reset state of the clock configuration is given below:
* - HSI ON and used as system clock source
* - HSE, PLL, PLLI2S, PLLSAI OFF
* - AHB, APB1 and APB2 prescaler set to 1.
* - CSS, MCO OFF
* - All interrupts disabled
* @note This function doesn't modify the configuration of the
* - Peripheral clocks
* - LSI, LSE and RTC clocks
* @retval An ErrorStatus enumeration value:
* - SUCCESS: RCC registers are de-initialized
* - ERROR: not applicable
*/
ErrorStatus LL_RCC_DeInit(void)
{
uint32_t vl_mask = 0xFFFFFFFFU;
/* Set HSION bit */
LL_RCC_HSI_Enable();
/* Wait for HSI READY bit */
while(LL_RCC_HSI_IsReady() != 1U)
{}
/* Reset CFGR register */
LL_RCC_WriteReg(CFGR, 0x00000000U);
/* Reset HSEON, HSEBYP, PLLON, CSSON, PLLI2SON and PLLSAION bits */
CLEAR_BIT(vl_mask, (RCC_CR_HSEON | RCC_CR_HSEBYP | RCC_CR_PLLON | RCC_CR_CSSON | RCC_CR_PLLSAION | RCC_CR_PLLI2SON));
/* Write new mask in CR register */
LL_RCC_WriteReg(CR, vl_mask);
/* Set HSITRIM bits to the reset value*/
LL_RCC_HSI_SetCalibTrimming(0x10U);
/* Wait for PLL READY bit to be reset */
while(LL_RCC_PLL_IsReady() != 0U)
{}
/* Wait for PLLI2S READY bit to be reset */
while(LL_RCC_PLLI2S_IsReady() != 0U)
{}
/* Wait for PLLSAI READY bit to be reset */
while(LL_RCC_PLLSAI_IsReady() != 0U)
{}
/* Reset PLLCFGR register */
LL_RCC_WriteReg(PLLCFGR, 0x24003010U);
/* Reset PLLI2SCFGR register */
LL_RCC_WriteReg(PLLI2SCFGR, 0x24003000U);
/* Reset PLLSAICFGR register */
LL_RCC_WriteReg(PLLSAICFGR, 0x24003000U);
/* Disable all interrupts */
CLEAR_BIT(RCC->CIR, RCC_CIR_LSIRDYIE | RCC_CIR_LSERDYIE | RCC_CIR_HSIRDYIE | RCC_CIR_HSERDYIE | RCC_CIR_PLLRDYIE | RCC_CIR_PLLI2SRDYIE | RCC_CIR_PLLSAIRDYIE);
/* Clear all interrupt flags */
SET_BIT(RCC->CIR, RCC_CIR_LSIRDYC | RCC_CIR_LSERDYC | RCC_CIR_HSIRDYC | RCC_CIR_HSERDYC | RCC_CIR_PLLRDYC | RCC_CIR_PLLI2SRDYC | RCC_CIR_PLLSAIRDYC | RCC_CIR_CSSC);
/* Clear LSION bit */
CLEAR_BIT(RCC->CSR, RCC_CSR_LSION);
/* Reset all CSR flags */
SET_BIT(RCC->CSR, RCC_CSR_RMVF);
return SUCCESS;
}
void clock_config(void)
{
LL_RCC_HSE_Enable();
while (!LL_RCC_HSE_IsReady());
LL_RCC_PLL_ConfigDomain_SYS(LL_RCC_PLLSOURCE_HSE, LL_RCC_PLL_MUL_9);
LL_RCC_PLL_Disable();
LL_RCC_PLL_Enable();
while (!LL_RCC_PLL_IsReady());
LL_RCC_SetAHBPrescaler(LL_RCC_SYSCLK_DIV_1);
LL_RCC_SetAPB1Prescaler(LL_RCC_APB1_DIV_2);
LL_RCC_SetAPB2Prescaler(LL_RCC_APB2_DIV_2);
LL_RCC_SetADCClockSource(LL_RCC_ADC_CLKSRC_PCLK2_DIV_4);
LL_FLASH_SetLatency(LL_FLASH_LATENCY_2);
LL_FLASH_EnablePrefetch();
LL_RCC_SetSysClkSource(LL_RCC_SYS_CLKSOURCE_PLL);
SystemCoreClockUpdate();
LL_Init1msTick(SystemCoreClock);
}
/**
* @brief Return RNGx clock frequency
* @param RNGxSource This parameter can be one of the following values:
* @arg @ref LL_RCC_RNG_CLKSOURCE
* @retval RNG clock frequency (in Hz)
* - @ref LL_RCC_PERIPH_FREQUENCY_NO indicates that oscillator (MSI) or PLL is not ready
* - @ref LL_RCC_PERIPH_FREQUENCY_NA indicates that no clock source selected
*/
uint32_t LL_RCC_GetRNGClockFreq(uint32_t RNGxSource)
{
uint32_t rng_frequency = LL_RCC_PERIPH_FREQUENCY_NO;
/* Check parameter */
assert_param(IS_LL_RCC_RNG_CLKSOURCE(RNGxSource));
/* RNGCLK clock frequency */
switch (LL_RCC_GetRNGClockSource(RNGxSource))
{
case LL_RCC_RNG_CLKSOURCE_PLLSAI1: /* PLLSAI1 clock used as RNG clock source */
if (LL_RCC_PLLSAI1_IsReady())
{
rng_frequency = RCC_PLLSAI1_GetFreqDomain_48M();
}
break;
case LL_RCC_RNG_CLKSOURCE_PLL: /* PLL clock used as RNG clock source */
if (LL_RCC_PLL_IsReady())
{
rng_frequency = RCC_PLL_GetFreqDomain_48M();
}
break;
case LL_RCC_RNG_CLKSOURCE_MSI: /* MSI clock used as RNG clock source */
if (LL_RCC_MSI_IsReady())
{
rng_frequency = __LL_RCC_CALC_MSI_FREQ(LL_RCC_MSI_IsEnabledRangeSelect(),
(LL_RCC_MSI_IsEnabledRangeSelect() ?
LL_RCC_MSI_GetRange() :
LL_RCC_MSI_GetRangeAfterStandby()));
}
break;
case LL_RCC_RNG_CLKSOURCE_NONE: /* No clock used as RNG clock source */
default:
rng_frequency = LL_RCC_PERIPH_FREQUENCY_NA;
break;
}
return rng_frequency;
}
/**
* @brief Return SAIx clock frequency
* @param SAIxSource This parameter can be one of the following values:
* @arg @ref LL_RCC_SAI1_CLKSOURCE
* @arg @ref LL_RCC_SAI2_CLKSOURCE (*)
*
* (*) value not defined in all devices.
* @retval SAI clock frequency (in Hz)
* - @ref LL_RCC_PERIPH_FREQUENCY_NO indicates that PLL is not ready
* - @ref LL_RCC_PERIPH_FREQUENCY_NA indicates that external clock is used
*/
uint32_t LL_RCC_GetSAIClockFreq(uint32_t SAIxSource)
{
uint32_t sai_frequency = LL_RCC_PERIPH_FREQUENCY_NO;
/* Check parameter */
assert_param(IS_LL_RCC_SAI_CLKSOURCE(SAIxSource));
if (SAIxSource == LL_RCC_SAI1_CLKSOURCE)
{
/* SAI1CLK clock frequency */
switch (LL_RCC_GetSAIClockSource(SAIxSource))
{
case LL_RCC_SAI1_CLKSOURCE_PLLSAI1: /* PLLSAI1 clock used as SAI1 clock source */
if (LL_RCC_PLLSAI1_IsReady())
{
sai_frequency = RCC_PLLSAI1_GetFreqDomain_SAI();
}
break;
#if defined(RCC_PLLSAI2_SUPPORT)
case LL_RCC_SAI1_CLKSOURCE_PLLSAI2: /* PLLSAI2 clock used as SAI1 clock source */
if (LL_RCC_PLLSAI2_IsReady())
{
sai_frequency = RCC_PLLSAI2_GetFreqDomain_SAI();
}
break;
#endif /* RCC_PLLSAI2_SUPPORT */
case LL_RCC_SAI1_CLKSOURCE_PLL: /* PLL clock used as SAI1 clock source */
if (LL_RCC_PLL_IsReady())
{
sai_frequency = RCC_PLL_GetFreqDomain_SAI();
}
break;
case LL_RCC_SAI1_CLKSOURCE_PIN: /* External input clock used as SAI1 clock source */
default:
sai_frequency = LL_RCC_PERIPH_FREQUENCY_NA;
break;
}
}
else
{
#if defined(RCC_CCIPR_SAI2SEL)
if (SAIxSource == LL_RCC_SAI2_CLKSOURCE)
{
/* SAI2CLK clock frequency */
switch (LL_RCC_GetSAIClockSource(SAIxSource))
{
case LL_RCC_SAI2_CLKSOURCE_PLLSAI1: /* PLLSAI1 clock used as SAI2 clock source */
if (LL_RCC_PLLSAI1_IsReady())
{
sai_frequency = RCC_PLLSAI1_GetFreqDomain_SAI();
}
break;
#if defined(RCC_PLLSAI2_SUPPORT)
case LL_RCC_SAI2_CLKSOURCE_PLLSAI2: /* PLLSAI2 clock used as SAI2 clock source */
if (LL_RCC_PLLSAI2_IsReady())
{
sai_frequency = RCC_PLLSAI2_GetFreqDomain_SAI();
}
break;
#endif /* RCC_PLLSAI2_SUPPORT */
case LL_RCC_SAI2_CLKSOURCE_PLL: /* PLL clock used as SAI2 clock source */
if (LL_RCC_PLL_IsReady())
{
sai_frequency = RCC_PLL_GetFreqDomain_SAI();
}
break;
case LL_RCC_SAI2_CLKSOURCE_PIN: /* External input clock used as SAI2 clock source */
default:
sai_frequency = LL_RCC_PERIPH_FREQUENCY_NA;
break;
}
}
#endif /*RCC_CCIPR_SAI2SEL*/
}
return sai_frequency;
}
/**
* @brief Return SDMMCx clock frequency
* @param SDMMCxSource This parameter can be one of the following values:
* @arg @ref LL_RCC_SDMMC1_CLKSOURCE
* @arg @ref LL_RCC_SDMMC2_CLKSOURCE (*)
*
* (*) value not defined in all devices.
* @retval SDMMC clock frequency (in Hz)
* - @ref LL_RCC_PERIPH_FREQUENCY_NO indicates that oscillator PLL is not ready
*/
uint32_t LL_RCC_GetSDMMCClockFreq(uint32_t SDMMCxSource)
{
uint32_t sdmmc_frequency = LL_RCC_PERIPH_FREQUENCY_NO;
/* Check parameter */
assert_param(IS_LL_RCC_SDMMC_CLKSOURCE(SDMMCxSource));
if (SDMMCxSource == LL_RCC_SDMMC1_CLKSOURCE)
{
/* SDMMC1CLK clock frequency */
switch (LL_RCC_GetSDMMCClockSource(SDMMCxSource))
{
case LL_RCC_SDMMC1_CLKSOURCE_PLL48CLK: /* PLL48 clock used as SDMMC1 clock source */
switch (LL_RCC_GetCK48MClockSource(LL_RCC_CK48M_CLKSOURCE))
{
case LL_RCC_CK48M_CLKSOURCE_PLL: /* PLL clock used as 48Mhz domain clock */
if (LL_RCC_PLL_IsReady())
{
sdmmc_frequency = RCC_PLL_GetFreqDomain_48M();
}
break;
case LL_RCC_CK48M_CLKSOURCE_PLLSAI: /* PLLSAI clock used as 48Mhz domain clock */
default:
if (LL_RCC_PLLSAI_IsReady())
{
sdmmc_frequency = RCC_PLLSAI_GetFreqDomain_48M();
}
break;
}
break;
case LL_RCC_SDMMC1_CLKSOURCE_SYSCLK: /* PLL clock used as SDMMC1 clock source */
default:
sdmmc_frequency = RCC_GetSystemClockFreq();
break;
}
}
#if defined(SDMMC2)
else
{
/* SDMMC2CLK clock frequency */
switch (LL_RCC_GetSDMMCClockSource(SDMMCxSource))
{
case LL_RCC_SDMMC2_CLKSOURCE_PLL48CLK: /* PLL48 clock used as SDMMC2 clock source */
switch (LL_RCC_GetCK48MClockSource(LL_RCC_CK48M_CLKSOURCE))
{
case LL_RCC_CK48M_CLKSOURCE_PLL: /* PLL clock used as 48Mhz domain clock */
if (LL_RCC_PLL_IsReady())
{
sdmmc_frequency = RCC_PLL_GetFreqDomain_48M();
}
break;
case LL_RCC_CK48M_CLKSOURCE_PLLSAI: /* PLLSAI clock used as 48Mhz domain clock */
default:
if (LL_RCC_PLLSAI_IsReady())
{
sdmmc_frequency = RCC_PLLSAI_GetFreqDomain_48M();
}
break;
}
break;
case LL_RCC_SDMMC2_CLKSOURCE_SYSCLK: /* PLL clock used as SDMMC2 clock source */
default:
sdmmc_frequency = RCC_GetSystemClockFreq();
break;
}
}
#endif /* SDMMC2 */
return sdmmc_frequency;
}
static int usb_dc_stm32_clock_enable(void)
{
struct device *clk = device_get_binding(STM32_CLOCK_CONTROL_NAME);
struct stm32_pclken pclken = {
#ifdef DT_USB_HS_BASE_ADDRESS
.bus = STM32_CLOCK_BUS_AHB1,
.enr = LL_AHB1_GRP1_PERIPH_OTGHS
#else /* DT_USB_HS_BASE_ADDRESS */
#ifdef USB
.bus = STM32_CLOCK_BUS_APB1,
.enr = LL_APB1_GRP1_PERIPH_USB,
#else /* USB_OTG_FS */
#ifdef CONFIG_SOC_SERIES_STM32F1X
.bus = STM32_CLOCK_BUS_AHB1,
.enr = LL_AHB1_GRP1_PERIPH_OTGFS,
#else
.bus = STM32_CLOCK_BUS_AHB2,
.enr = LL_AHB2_GRP1_PERIPH_OTGFS,
#endif /* CONFIG_SOC_SERIES_STM32F1X */
#endif /* USB */
#endif /* DT_USB_HS_BASE_ADDRESS */
};
/*
* Some SoCs in STM32F0/L0/L4 series disable USB clock by
* default. We force USB clock source to MSI or PLL clock for this
* SoCs. However, if these parts have an HSI48 clock, use
* that instead. Example reference manual RM0360 for
* STM32F030x4/x6/x8/xC and STM32F070x6/xB.
*/
#if defined(RCC_HSI48_SUPPORT)
/*
* In STM32L0 series, HSI48 requires VREFINT and its buffer
* with 48 MHz RC to be enabled.
* See ENREF_HSI48 in referenc maual RM0367 section10.2.3:
* "Reference control and status register (SYSCFG_CFGR3)"
*/
#ifdef CONFIG_SOC_SERIES_STM32L0X
if (LL_APB2_GRP1_IsEnabledClock(LL_APB2_GRP1_PERIPH_SYSCFG)) {
LL_SYSCFG_VREFINT_EnableHSI48();
} else {
LOG_ERR("System Configuration Controller clock is "
"disabled. Unable to enable VREFINT which "
"is required by HSI48.");
}
#endif /* CONFIG_SOC_SERIES_STM32L0X */
LL_RCC_HSI48_Enable();
while (!LL_RCC_HSI48_IsReady()) {
/* Wait for HSI48 to become ready */
}
LL_RCC_SetUSBClockSource(LL_RCC_USB_CLKSOURCE_HSI48);
#elif defined(LL_RCC_USB_CLKSOURCE_NONE)
/* When MSI is configured in PLL mode with a 32.768 kHz clock source,
* the MSI frequency can be automatically trimmed by hardware to reach
* better than ±0.25% accuracy. In this mode the MSI can feed the USB
* device. For now, we only use MSI for USB if not already used as
* system clock source.
*/
#if defined(CONFIG_CLOCK_STM32_MSI_PLL_MODE) && !defined(CONFIG_CLOCK_STM32_SYSCLK_SRC_MSI)
LL_RCC_MSI_Enable();
while (!LL_RCC_MSI_IsReady()) {
/* Wait for MSI to become ready */
}
/* Force 48 MHz mode */
LL_RCC_MSI_EnableRangeSelection();
LL_RCC_MSI_SetRange(LL_RCC_MSIRANGE_11);
LL_RCC_SetUSBClockSource(LL_RCC_USB_CLKSOURCE_MSI);
#else
if (LL_RCC_PLL_IsReady()) {
LL_RCC_SetUSBClockSource(LL_RCC_USB_CLKSOURCE_PLL);
} else {
LOG_ERR("Unable to set USB clock source to PLL.");
}
#endif /* CONFIG_CLOCK_STM32_MSI_PLL_MODE && !CONFIG_CLOCK_STM32_SYSCLK_SRC_MSI */
#endif /* RCC_HSI48_SUPPORT / LL_RCC_USB_CLKSOURCE_NONE */
if (clock_control_on(clk, (clock_control_subsys_t *)&pclken) != 0) {
LOG_ERR("Unable to enable USB clock");
return -EIO;
}
#ifdef DT_USB_HS_BASE_ADDRESS
#ifdef DT_COMPAT_ST_STM32_USBPHYC
LL_AHB1_GRP1_EnableClock(LL_AHB1_GRP1_PERIPH_OTGHSULPI);
LL_APB2_GRP1_EnableClock(LL_APB2_GRP1_PERIPH_OTGPHYC);
#else
/* Disable ULPI interface (for external high-speed PHY) clock */
LL_AHB1_GRP1_DisableClock(LL_AHB1_GRP1_PERIPH_OTGHSULPI);
LL_AHB1_GRP1_DisableClockLowPower(LL_AHB1_GRP1_PERIPH_OTGHSULPI);
#endif /* DT_COMPAT_ST_STM32_USBPHYC */
#endif /* DT_USB_HS_BASE_ADDRESS */
return 0;
}
#if defined(USB_OTG_FS) || defined(USB_OTG_HS)
static u32_t usb_dc_stm32_get_maximum_speed(void)
{
/*
* If max-speed is not passed via DT, set it to USB controller's
* maximum hardware capability.
*/
#if defined(DT_COMPAT_ST_STM32_USBPHYC) && defined(DT_USB_HS_BASE_ADDRESS)
u32_t speed = USB_OTG_SPEED_HIGH;
#else
u32_t speed = USB_OTG_SPEED_FULL;
#endif /* DT_COMPAT_ST_STM32_USBPHYC && DT_USB_HS_BASE_ADDRESS */
#ifdef DT_USB_MAXIMUM_SPEED
if (!strncmp(DT_USB_MAXIMUM_SPEED, "high-speed", 10)) {
speed = USB_OTG_SPEED_HIGH;
} else if (!strncmp(DT_USB_MAXIMUM_SPEED, "full-speed", 10)) {
#if defined(DT_COMPAT_ST_STM32_USBPHYC) && defined(DT_USB_HS_BASE_ADDRESS)
speed = USB_OTG_SPEED_HIGH_IN_FULL;
#else
speed = USB_OTG_SPEED_FULL;
#endif /* DT_COMPAT_ST_STM32_USBPHYC && DT_USB_HS_BASE_ADDRESS */
} else if (!strncmp(DT_USB_MAXIMUM_SPEED, "low-speed", 9)) {
speed = USB_OTG_SPEED_LOW;
} else {
LOG_DBG("Unsupported maximum speed defined in device tree. "
"USB controller will default to its maximum HW "
"capability");
}
#endif /* DT_USB_MAXIMUM_SPEED */
return speed;
}
