C++ (Cpp) MACISR示例

示例#1

文件： vscptest.c 项目： dbortolini/vscp_firmware

    void interrupt HighISR(void)
#endif
{
    //TMR0 is used for the ticks
    if (INTCON_TMR0IF)
    {
        TickUpdate();

        #if defined(STACK_USE_SLIP)
        MACISR();
        #endif

        INTCON_TMR0IF = 0;
    }


    #ifdef SER_USE_INTERRUPT
    //USART Receive
	if(PIR1_RCIF && PIE1_RCIE)
	{
        serRxIsr();
	}

    //USART Transmit
	if(PIR1_TXIF && PIE1_TXIE)
	{
        serTxIsr();
	}
    #endif
}

示例#2

文件： mxwebsrvr.c 项目： dbortolini/vscp_firmware

    void interrupt HighISR(void)
#endif
{
    TickUpdate();

#if defined(STACK_USE_SLIP)
    MACISR();
#endif
}

示例#3

文件： main_udp5.c 项目： bmo/SBC65EC-based-interlock

    void interrupt HighISR(void)
#endif
{
    //TMR0 is used for the ticks
    if (INTCON_TMR0IF)
    {
        TickUpdate();

        #if defined(STACK_USE_SLIP)
        MACISR();
        #endif

        INTCON_TMR0IF = 0;
    }
}

示例#4

文件： mxwebsrvr.c 项目： dbortolini/vscp_firmware

    void interrupt HighISR(void)
#endif
{
    /////////////////////////////////////////////////
    //TMR0 is used for the ticks
    if (INTCON_TMR0IF)
    {
        TickUpdate();

        #if defined(STACK_USE_SLIP)
        MACISR();
        #endif

        INTCON_TMR0IF = 0;
    }


    /////////////////////////////////////////////////
    //USART1
    if(PIR1_RCIF && PIE1_RCIE)  //USART1 Receive
    {
        serRxIsr();
    }

    //USART1 Transmit
    if(PIR1_TXIF && PIE1_TXIE)
    {
        serTxIsr();
    }


    #if defined(BRD_SBC65EC)
    /////////////////////////////////////////////////
    //USART2
    if(PIR3_RC2IF && PIE3_RC2IE)  //USART2 Receive
    {
        ser2RxIsr();
    }

    //USART2 Transmit
    if(PIR3_TX2IF && PIE3_TX2IE)
    {
        ser2TxIsr();
    }
    #endif
}

示例#5

文件： nova.c 项目： dbortolini/vscp_firmware

    void interrupt HighISR(void)
#endif
{
    //TMR0 is used for the ticks
    if (INTCON_TMR0IF)
    {
        TickUpdate();

        #if defined(STACK_USE_SLIP)
        MACISR();
        #endif

        INTCON_TMR0IF = 0;
    }


    #ifdef SER_USE_INTERRUPT
    //USART Receive
	if(PIR1_RCIF && PIE1_RCIE)
	{
        serRxIsr();
	}

    //USART Transmit
	if(PIR1_TXIF && PIE1_TXIE)
	{
        serTxIsr();
	}
    #endif

	// ERRIF: CAN bus Error Interrupt Flag bit
	if ( PIR3bits.ERRIF ) 
	{
		// save the comstat register for analysis later on
		g_can_error = COMSTAT;
		COMSTAT = 0;
		PIR3 = 0;	
	}
	// CAN support
}