void
OSD::update() {
uint8_t *b = osdbuf;
uint8_t *end_b = b+sizeof(osdbuf);
PORTD &= ~_BV(PD6); // digitalWrite(MAX7456_SELECT,LOW);
MAX_write(MAX7456_DMAH_reg, 0);
MAX_write(MAX7456_DMAL_reg, 0);
MAX_write(MAX7456_DMM_reg, 1);
PORTD |= _BV(PD6); // digitalWrite(MAX7456_SELECT, HIGH);
for(; b < end_b; b++) {
PORTD &= ~_BV(PD6); // digitalWrite(MAX7456_SELECT, HIGH);
SPDR = *b;
*b=' '; // обойдемся без memset
while (!(SPSR & (1<<SPIF))) ;
PORTD |= _BV(PD6); // digitalWrite(MAX7456_SELECT,LOW);
}
PORTD &= ~_BV(PD6); // digitalWrite(MAX7456_SELECT,LOW); /CS OSD
Spi.transfer(MAX7456_END_string);
PORTD |= _BV(PD6); // digitalWrite(MAX7456_SELECT, HIGH);
// memset(osdbuf, ' ', sizeof(osdbuf));
}
void OSD::hw_init(){
max7456_on();
//read black level register
byte osdbl_r = MAX_read(MAX7456_OSDBL_reg_read); //black level read register
MAX_write(MAX7456_VM0_reg, MAX7456_RESET | video_mode);
delay_150();
//set black level
MAX_write(MAX7456_OSDBL_reg, (osdbl_r & 0xef)); //black level write register - Set bit 4 to zero 11101111 - Enable automatic OSD black level control
MAX_write(MAX7456_OSDM_reg, 0b00010010); // 0x00011011 default
// define sync (auto,int,ext)
MAX_write(MAX7456_VM0_reg, (MAX7456_ENABLE_display_vert | video_mode) | MAX7456_SYNC_internal); // first time on internal sync
delay_150();
MAX_write(MAX7456_VM0_reg, (MAX7456_ENABLE_display_vert | video_mode) | MAX7456_SYNC_autosync); // and then switch to auto mode
// max7456_off();
adjust();
}
void OSD::update() {
uint8_t *b = osdbuf;
uint8_t *end_b = b+sizeof(osdbuf);
/*
wee need to transfer 480 bytes, SPI speed set to 8 MHz (MAX requires min 100ns SCK period) so one byte goes in 1uS and all transfer will ends up in ~500uS
*/
#ifdef SLAVE_BUILD
// internal Ardupilot build should use DMA to transfer
max7456_on();
#else
max7456_on();
MAX_write(MAX7456_DMAH_reg, 0);
MAX_write(MAX7456_DMAL_reg, 0);
MAX_write(MAX7456_DMM_reg, 1); // автоинкремент адреса
max7456_off();
for(; b < end_b;) {
max7456_on(); // strobing each byte with CS is necessary :(
SPI::transfer(*b);
*b++=' ';
max7456_off();
}
max7456_on();
SPI::transfer(MAX7456_END_string); // 0xFF - "end of screen" character
#endif
max7456_off();
}
void OSD::update() {
uint8_t *b = osdbuf;
uint8_t *end_b = b+sizeof(osdbuf);
/*
uint8_t bit = digitalPinToBitMask(MAX7456_SELECT); // move calculations from critical section
uint8_t port = digitalPinToPort(MAX7456_SELECT);
volatile uint8_t *out = portOutputRegister(port);
#define SET_LOW() *out &= ~bit
#define SET_HIGH() *out |= bit
*/
PORTD &= ~_BV(PD6); // digitalWrite(MAX7456_SELECT,LOW);
MAX_write(MAX7456_DMAH_reg, 0);
MAX_write(MAX7456_DMAL_reg, 0);
MAX_write(MAX7456_DMM_reg, 1); // автоинкремент адреса
PORTD |= _BV(PD6); // digitalWrite(MAX7456_SELECT, HIGH);
for(; b < end_b; b++) {
PORTD &= ~_BV(PD6); // digitalWrite(MAX7456_SELECT, HIGH);
SPDR = *b;
*b=' '; // обойдемся без memset
while (!(SPSR & (1<<SPIF))) ;
PORTD |= _BV(PD6); // digitalWrite(MAX7456_SELECT,LOW);
}
PORTD &= ~_BV(PD6); // digitalWrite(MAX7456_SELECT,LOW); /CS OSD
Spi.transfer(MAX7456_END_string);
PORTD |= _BV(PD6); // digitalWrite(MAX7456_SELECT, HIGH);
}
void OSD::adjust(){
max7456_on();
setBrightness();
//Serial.printf_P(PSTR("adjust bright=%d horiz=%d vert=%d\n"),sets.OSD_BRIGHTNESS,sets.horiz_offs, sets.vert_offs);
MAX_write(MAX7456_HOS_reg, /* 0x20 + */ sets.horiz_offs); // 0x20 default - already shifted
MAX_write(MAX7456_VOS_reg, /* 0x10 + */ sets.vert_offs); // 0x10 default
max7456_off();
}
void
OSD::control(uint8_t ctrl){
digitalWrite(MAX7456_SELECT,LOW);
switch(ctrl){
case 0:
MAX_write(MAX7456_VM0_reg, MAX7456_DISABLE_display | video_mode);
break;
case 1:
MAX_write(MAX7456_VM0_reg, (MAX7456_ENABLE_display_vert | video_mode) | MAX7456_SYNC_autosync);
break;
}
digitalWrite(MAX7456_SELECT,HIGH);
}
void OSD::clear()
{
// clear the screen
digitalWrite(MAX7456_SELECT,LOW);
MAX_write(MAX7456_DMM_reg, MAX7456_CLEAR_display);
digitalWrite(MAX7456_SELECT,HIGH);
}
void OSD::write_NVM(uint16_t font_count, uint8_t *character_bitmap)
{
byte x;
byte char_address_hi;
byte screen_char;
char_address_hi = font_count;
// byte char_address_lo = 0; - autoincrement mode
// cli(); - нет смысла
max7456_on();
MAX_mode( MAX7456_DISABLE_display);
MAX_write(MAX7456_CMAH_reg, char_address_hi);// set start address high
for(x = 0; x < NVM_ram_size; x++) {// write out 54 (out of 64) bytes of character to shadow ram
screen_char = *character_bitmap++;
MAX_write(MAX7456_CMAL_reg, x);// set start address low
MAX_write(MAX7456_CMDI_reg, screen_char);
}
// transfer a 54 bytes from shadow ram to NVM
MAX_write(MAX7456_CMM_reg, WRITE_nvr);
// wait until bit 5 in the status register returns to 0 (12ms)
#if 0
while (1) {
Spi.transfer(MAX7456_STAT_reg_read);
if(!(Spi.transfer(0xff) & STATUS_reg_nvr_busy)) break;
}
#else
while (1) {
if(!(MAX_read(MAX7456_STAT_reg_read) & STATUS_reg_nvr_busy)) break;
extern void delay_telem();
delay_telem(); // some delay
}
#endif
MAX_mode( MAX7456_ENABLE_display_vert);// turn on screen next vertical
max7456_off();
}
void OSD::hw_init() {
max7456_on();
//read black level register
byte osdbl_r = MAX_read(MAX7456_OSDBL_reg_read);//black level read register
MAX_write(MAX7456_VM0_reg, MAX7456_RESET | video_mode);
delay_150();
//set black level
MAX_write(MAX7456_OSDBL_reg, (osdbl_r & 0xef)); //black level write register - Set bit 4 to zero 11101111 - Enable automatic OSD black level control
// set position - may be EEPROM.read(OSD_SHIFT_X)
MAX_write(MAX7456_HOS_reg, 0x20); // 0x20 default
MAX_write(MAX7456_VOS_reg, 0x10); // 0x10 default
MAX_write(MAX7456_OSDM_reg, 0b00010010); // 0x00011011 default
setBrightness();
// define sync (auto,int,ext)
// MAX_write(MAX7456_VM0_reg, MAX7456_DISABLE_display | video_mode);
MAX_write(MAX7456_VM0_reg, (MAX7456_ENABLE_display_vert | video_mode) | MAX7456_SYNC_internal);
delay_150();
MAX_write(MAX7456_VM0_reg, (MAX7456_ENABLE_display_vert | video_mode) | MAX7456_SYNC_autosync);
max7456_off();
}
void OSD::hw_init(){
digitalWrite(MAX7456_SELECT,LOW);
//read black level register
byte osdbl_r = MAX_read(MAX7456_OSDBL_reg_read);//black level read register
MAX_write(MAX7456_VM0_reg, MAX7456_RESET | video_mode);
delay(150);
//set black level
MAX_write(MAX7456_OSDBL_reg, (osdbl_r & 0xef)); //black level write register - Set bit 4 to zero 11101111 - Enable automatic OSD black level control
// set position - may be EEPROM.read(OSD_SHIFT_X)
MAX_write(MAX7456_HOS_reg, 0x20); // 0x20 default
MAX_write(MAX7456_VOS_reg, 0x10); // 0x10 default
// MAX_write(MAX7456_HOS_reg, sets.horiz_offs); // 0x20 default
// MAX_write(MAX7456_VOS_reg, sets.vert_offs); // 0x10 default
setBrightness();
// define sync (auto,int,ext) and
// making sure the Max7456 is enabled
control(1);
}
//------------------ Set Brightness ---------------------------------
void OSD::setBrightness()
{
static const uint8_t levels[] PROGMEM = {
MAX7456_WHITE_level_80, // 0
MAX7456_WHITE_level_90, // 1
MAX7456_WHITE_level_100,// 2
MAX7456_WHITE_level_120,// 3
};
uint8_t blevel = sets.OSD_BRIGHTNESS;
if(blevel>3) blevel=0;
blevel=levels[blevel];
// set all rows to same character white level, 90%
for (byte x = 0x0, a= 0x10; x < 0x10; x++)
MAX_write(a++, blevel);
}
void OSD::setMode(uint8_t themode){
uint8_t mode;
switch(themode){
case 0:
mode = MAX7456_MODE_MASK_NTCS;
video_center = MAX7456_CENTER_NTSC;
break;
case 1:
mode = MAX7456_MODE_MASK_PAL;
video_center = MAX7456_CENTER_PAL;
break;
}
if(video_mode != mode){
video_mode = mode;
max7456_on();
MAX_write(MAX7456_VM0_reg, (MAX7456_ENABLE_display_vert | video_mode) | MAX7456_SYNC_autosync);
max7456_off();
}
}
//------------------ Set Brightness ---------------------------------
void OSD::setBrightness()
{
static const uint8_t levels[] PROGMEM = {
MAX7456_WHITE_level_80, // 0
MAX7456_WHITE_level_90, // 1
MAX7456_WHITE_level_100,// 2
MAX7456_WHITE_level_120,// 3
};
uint8_t blevel = sets.OSD_BRIGHTNESS;
if(blevel>3) blevel=0;
blevel=pgm_read_byte(&levels[blevel]);
Serial.printf(PSTR("\n\nSet bright to %d\n"),blevel);
// set all rows to same character white level
for (byte x = 0x0, a= 0x10 /* RB0 register */; x < 0x10; x++)
MAX_write(a++, blevel);
}
//*
void OSD::write_NVM(int font_count, uint8_t *character_bitmap)
{
byte x;
byte char_address_hi;
byte screen_char;
char_address_hi = font_count;
// byte char_address_lo = 0;
// cli();
max7456_on();
MAX_write(MAX7456_VM0_reg, MAX7456_DISABLE_display);
MAX_write(MAX7456_CMAH_reg, char_address_hi);// set start address high
for(x = 0; x < NVM_ram_size; x++) {// write out 54 (out of 64) bytes of character to shadow ram
screen_char = *character_bitmap++;
MAX_write(MAX7456_CMAL_reg, x);// set start address low
MAX_write(MAX7456_CMDI_reg, screen_char);
}
// transfer a 54 bytes from shadow ram to NVM
MAX_write(MAX7456_CMM_reg, WRITE_nvr);
// wait until bit 5 in the status register returns to 0 (12ms)
while (1) {
Spi.transfer(MAX7456_STAT_reg_read);
if(!(Spi.transfer(0xff) & STATUS_reg_nvr_busy)) break;
}
// sei();
MAX_write(MAX7456_VM0_reg, MAX7456_ENABLE_display_vert);// turn on screen next vertical
max7456_off();
}
void MAX_mode(byte mode){
MAX_write(MAX7456_VM0_reg, mode);
}
void OSD::clear() { // clear the screen
max7456_on();
MAX_write(MAX7456_DMM_reg, MAX7456_CLEAR_display);
max7456_off();
}