static void __init atari_scsi_reset_boot(void)
{
unsigned long end;
/*
* Do a SCSI reset to clean up the bus during initialization. No messing
* with the queues, interrupts, or locks necessary here.
*/
printk( "Atari SCSI: resetting the SCSI bus..." );
/* get in phase */
NCR5380_write( TARGET_COMMAND_REG,
PHASE_SR_TO_TCR( NCR5380_read(STATUS_REG) ));
/* assert RST */
NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST );
/* The min. reset hold time is 25us, so 40us should be enough */
udelay( 50 );
/* reset RST and interrupt */
NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE );
NCR5380_read( RESET_PARITY_INTERRUPT_REG );
end = jiffies + AFTER_RESET_DELAY;
while (time_before(jiffies, end))
barrier();
printk( " done\n" );
}
static void mac_scsi_reset_boot(struct Scsi_Host *instance)
{
unsigned long end;
NCR5380_local_declare();
NCR5380_setup(instance);
printk(KERN_INFO "Macintosh SCSI: resetting the SCSI bus..." );
disable_irq(IRQ_MAC_SCSI);
NCR5380_write( TARGET_COMMAND_REG,
PHASE_SR_TO_TCR( NCR5380_read(STATUS_REG) ));
NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST );
udelay( 50 );
NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE );
NCR5380_read( RESET_PARITY_INTERRUPT_REG );
for( end = jiffies + AFTER_RESET_DELAY; time_before(jiffies, end); )
barrier();
enable_irq(IRQ_MAC_SCSI);
printk(KERN_INFO " done\n" );
}
static void mac_scsi_reset_boot(struct Scsi_Host *instance)
{
unsigned long end;
NCR5380_local_declare();
NCR5380_setup(instance);
/*
* Do a SCSI reset to clean up the bus during initialization. No messing
* with the queues, interrupts, or locks necessary here.
*/
printk(KERN_INFO "Macintosh SCSI: resetting the SCSI bus..." );
/* get in phase */
NCR5380_write( TARGET_COMMAND_REG,
PHASE_SR_TO_TCR( NCR5380_read(STATUS_REG) ));
/* assert RST */
NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST );
/* The min. reset hold time is 25us, so 40us should be enough */
udelay( 50 );
/* reset RST and interrupt */
NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE );
NCR5380_read( RESET_PARITY_INTERRUPT_REG );
for( end = jiffies + AFTER_RESET_DELAY; time_before(jiffies, end); )
barrier();
printk(KERN_INFO " done\n" );
}
static void g_NCR5380_trigger_irq(struct Scsi_Host *instance)
{
struct NCR5380_hostdata *hostdata = shost_priv(instance);
/*
* An interrupt is triggered whenever BSY = false, SEL = true
* and a bit set in the SELECT_ENABLE_REG is asserted on the
* SCSI bus.
*
* Note that the bus is only driven when the phase control signals
* (I/O, C/D, and MSG) match those in the TCR.
*/
NCR5380_write(TARGET_COMMAND_REG,
PHASE_SR_TO_TCR(NCR5380_read(STATUS_REG) & PHASE_MASK));
NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask);
NCR5380_write(INITIATOR_COMMAND_REG,
ICR_BASE | ICR_ASSERT_DATA | ICR_ASSERT_SEL);
msleep(1);
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
NCR5380_write(SELECT_ENABLE_REG, 0);
NCR5380_write(TARGET_COMMAND_REG, 0);
}
static void sun3_scsi_reset_boot(struct Scsi_Host *instance)
{
unsigned long end;
NCR5380_local_declare();
NCR5380_setup(instance);
/*
* Do a SCSI reset to clean up the bus during initialization. No
* messing with the queues, interrupts, or locks necessary here.
*/
printk( "Sun3 SCSI: resetting the SCSI bus..." );
/* switch off SCSI IRQ - catch an interrupt without IRQ bit set else */
// sun3_disable_irq( IRQ_SUN3_SCSI );
/* get in phase */
NCR5380_write( TARGET_COMMAND_REG,
PHASE_SR_TO_TCR( NCR5380_read(STATUS_REG) ));
/* assert RST */
NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST );
/* The min. reset hold time is 25us, so 40us should be enough */
udelay( 50 );
/* reset RST and interrupt */
NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE );
NCR5380_read( RESET_PARITY_INTERRUPT_REG );
for( end = jiffies + AFTER_RESET_DELAY; time_before(jiffies, end); )
barrier();
/* switch on SCSI IRQ again */
// sun3_enable_irq( IRQ_SUN3_SCSI );
printk( " done\n" );
}
