static void intel_enable_transcoder(struct drm_i915_private *dev_priv,
enum pipe pipe)
{
int reg;
u32 val;
/* PCH only available on ILK+ */
assert(dev_priv->info->gen < 5);
/* Make sure PCH DPLL is enabled */
assert_pch_pll_enabled(dev_priv, pipe);
/* FDI must be feeding us bits for PCH ports */
assert_fdi_tx_enabled(dev_priv, pipe);
assert_fdi_rx_enabled(dev_priv, pipe);
reg = TRANSCONF(pipe);
val = I915_READ(reg);
/*
* make the BPC in transcoder be consistent with
* that in pipeconf reg.
*/
val &= ~PIPE_BPC_MASK;
val |= I915_READ(PIPECONF(pipe)) & PIPE_BPC_MASK;
I915_WRITE(reg, val | TRANS_ENABLE);
if (wait_for(I915_READ(reg) & TRANS_STATE_ENABLE, 100))
fprintf(stderr, "failed to enable transcoder %d\n", pipe);
}
/**
* intel_enable_pipe - enable a pipe, asserting requirements
* @dev_priv: i915 private structure
* @pipe: pipe to enable
* @pch_port: on ILK+, is this pipe driving a PCH port or not
*
* Enable @pipe, making sure that various hardware specific requirements
* are met, if applicable, e.g. PLL enabled, LVDS pairs enabled, etc.
*
* @pipe should be %PIPE_A or %PIPE_B.
*
* Will wait until the pipe is actually running (i.e. first vblank) before
* returning.
*/
static void intel_enable_pipe(struct drm_i915_private *dev_priv, enum pipe pipe,
bool pch_port)
{
int reg;
u32 val;
/*
* A pipe without a PLL won't actually be able to drive bits from
* a plane. On ILK+ the pipe PLLs are integrated, so we don't
* need the check.
*/
if (!HAS_PCH_SPLIT(dev_priv->dev))
assert_pll_enabled(dev_priv, pipe);
else {
if (pch_port) {
/* if driving the PCH, we need FDI enabled */
assert_fdi_rx_pll_enabled(dev_priv, pipe);
assert_fdi_tx_pll_enabled(dev_priv, pipe);
}
/* FIXME: assert CPU port conditions for SNB+ */
}
reg = PIPECONF(pipe);
val = I915_READ(reg);
if (val & PIPECONF_ENABLE)
return;
I915_WRITE(reg, val | PIPECONF_ENABLE);
intel_wait_for_vblank(dev_priv->dev, pipe);
}
/*
* intel_wait_for_pipe_off - wait for pipe to turn off
* @dev: drm device
* @pipe: pipe to wait for
*
* After disabling a pipe, we can't wait for vblank in the usual way,
* spinning on the vblank interrupt status bit, since we won't actually
* see an interrupt when the pipe is disabled.
*
* On Gen4 and above:
* wait for the pipe register state bit to turn off
*
* Otherwise:
* wait for the display line value to settle (it usually
* ends up stopping at the start of the next frame).
*
*/
void intel_wait_for_pipe_off(struct drm_device *dev, int pipe)
{
struct drm_i915_private *dev_priv = dev->dev_private;
if (INTEL_INFO(dev)->gen >= 4) {
int reg = PIPECONF(pipe);
/* Wait for the Pipe State to go off */
if (wait_for((I915_READ(reg) & I965_PIPECONF_ACTIVE) == 0,
100))
fprintf(stderr, "pipe_off wait timed out\n");
} else {
u32 last_line;
int reg = PIPEDSL(pipe);
unsigned long timeout = msecs() + 100;
/* Wait for the display line to settle */
do {
last_line = I915_READ(reg) & DSL_LINEMASK;
mdelay(5);
} while (((I915_READ(reg) & DSL_LINEMASK) != last_line) &&
(timeout> msecs()));
if ((msecs()> timeout))
fprintf(stderr, "pipe_off wait timed out\n");
}
}
static int setup_virtual_dp_monitor(struct intel_vgpu *vgpu, int port_num,
int type, unsigned int resolution)
{
struct drm_i915_private *dev_priv = vgpu->gvt->dev_priv;
struct intel_vgpu_port *port = intel_vgpu_port(vgpu, port_num);
if (WARN_ON(resolution >= GVT_EDID_NUM))
return -EINVAL;
port->edid = kzalloc(sizeof(*(port->edid)), GFP_KERNEL);
if (!port->edid)
return -ENOMEM;
port->dpcd = kzalloc(sizeof(*(port->dpcd)), GFP_KERNEL);
if (!port->dpcd) {
kfree(port->edid);
return -ENOMEM;
}
memcpy(port->edid->edid_block, virtual_dp_monitor_edid[resolution],
EDID_SIZE);
port->edid->data_valid = true;
memcpy(port->dpcd->data, dpcd_fix_data, DPCD_HEADER_SIZE);
port->dpcd->data_valid = true;
port->dpcd->data[DPCD_SINK_COUNT] = 0x1;
port->type = type;
emulate_monitor_status_change(vgpu);
vgpu_vreg(vgpu, PIPECONF(PIPE_A)) |= PIPECONF_ENABLE;
return 0;
}
int intel_drrs_configure_dsi_pll(struct intel_dsi *intel_dsi,
struct intel_dsi_mnp *intel_dsi_mnp)
{
struct drm_i915_private *dev_priv =
intel_dsi->base.base.dev->dev_private;
struct intel_crtc *intel_crtc =
to_intel_crtc(intel_dsi->base.base.crtc);
struct intel_mipi_drrs_work *work =
dev_priv->drrs.mipi_drrs_work;
u32 dsi_pll_ctrl, vactive;
u32 dsl_offset = PIPEDSL(intel_crtc->pipe), dsl;
unsigned long timeout;
intel_configure_dsi_pll_reg(dev_priv, intel_dsi_mnp, intel_dsi, true);
dsi_pll_ctrl = vlv_cck_read(dev_priv, CCK_REG_DSI_PLL_CONTROL);
dsi_pll_ctrl &= (~DSI_PLL_VCO_EN);
vactive = (I915_READ(VTOTAL(intel_crtc->pipe)) &
VERTICAL_ACTIVE_DISPLAY_MASK) + 1;
timeout = jiffies + msecs_to_jiffies(50);
do {
if (atomic_read(&work->abort_wait_loop) == 1) {
DRM_DEBUG_KMS("Aborting the pll update\n");
return -EPERM;
}
dsl = (I915_READ(dsl_offset) & DSL_LINEMASK_GEN3);
if (jiffies >= timeout) {
DRM_ERROR("Timeout at waiting for Vblank\n");
return -ETIMEDOUT;
}
} while (dsl <= vactive);
mutex_lock(&dev_priv->dpio_lock);
/* Toggle the VCO_EN to bring in the new dividers values */
vlv_cck_write(dev_priv, CCK_REG_DSI_PLL_CONTROL, dsi_pll_ctrl);
dsi_pll_ctrl |= DSI_PLL_VCO_EN;
vlv_cck_write(dev_priv, CCK_REG_DSI_PLL_CONTROL, dsi_pll_ctrl);
mutex_unlock(&dev_priv->dpio_lock);
DRM_DEBUG_KMS("PLL Changed between DSL: %d, %d\n",
dsl, I915_READ(dsl_offset) & DSL_LINEMASK_GEN3);
if (wait_for(I915_READ(PIPECONF(PIPE_A)) & PIPECONF_DSI_PLL_LOCKED,
20)) {
DRM_ERROR("DSI PLL lock failed\n");
return -EACCES;
}
return 0;
}
int intel_disable_dsi_pll(struct intel_dsi *intel_dsi)
{
struct drm_i915_private *dev_priv =
intel_dsi->base.base.dev->dev_private;
intel_cck_write32_bits(dev_priv, 0x48, 0x00000000, 0x80000000);
udelay(500);
/* FIXME: DSI PLL is disable before pipe is disabled, because of this
* ref clock will not be disabled when only mipi panel is connected.
* Need to fix this.
*/
if ((PIPECONF(PIPE_A) & PIPECONF_ENABLE == 0) &&
(PIPECONF(PIPE_B) & PIPECONF_ENABLE == 0)
)
I915_WRITE_BITS(_DPLL_A, 0x00000000, DPLL_REFA_CLK_ENABLE_VLV);
return 0;
}
static int edp_pipe_is_enabled(struct intel_vgpu *vgpu)
{
struct drm_i915_private *dev_priv = vgpu->gvt->dev_priv;
if (!(vgpu_vreg(vgpu, PIPECONF(_PIPE_EDP)) & PIPECONF_ENABLE))
return 0;
if (!(vgpu_vreg(vgpu, _TRANS_DDI_FUNC_CTL_EDP) & TRANS_DDI_FUNC_ENABLE))
return 0;
return 1;
}
int intel_disable_dsi_pll(struct intel_dsi *intel_dsi)
{
struct drm_i915_private *dev_priv = intel_dsi->base.base.dev->dev_private;
u32 tmp;
DRM_DEBUG_KMS("\n");
mutex_lock(&dev_priv->dpio_lock);
tmp = vlv_cck_read(dev_priv, CCK_REG_DSI_PLL_CONTROL);
tmp &= ~DSI_PLL_VCO_EN;
tmp |= DSI_PLL_LDO_GATE;
vlv_cck_write(dev_priv, CCK_REG_DSI_PLL_CONTROL, tmp);
if ((I915_READ(PIPECONF(PIPE_A)) & (PIPECONF_ENABLE == 0)) &&
(I915_READ(PIPECONF(PIPE_B)) & (PIPECONF_ENABLE == 0)))
I915_WRITE_BITS(_DPLL_A, 0x00000000, DPLL_REFA_CLK_ENABLE_VLV);
mutex_unlock(&dev_priv->dpio_lock);
return 0;
}
int intel_enable_dsi_pll(struct intel_dsi *intel_dsi)
{
struct drm_encoder *encoder = &(intel_dsi->base.base);
struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
struct drm_display_mode *mode = &intel_crtc->config.adjusted_mode;
struct drm_i915_private *dev_priv =
intel_dsi->base.base.dev->dev_private;
u32 tmp;
DRM_DEBUG_KMS("\n");
if ((I915_READ(PIPECONF(PIPE_A)) & PIPECONF_DSI_PLL_LOCKED)) {
DRM_DEBUG_KMS("DSI PLL Already locked\n");
return 0;
}
mutex_lock(&dev_priv->dpio_lock);
intel_configure_dsi_pll(intel_dsi, mode);
/* wait at least 0.5 us after ungating before enabling VCO */
usleep_range(1, 10);
tmp = vlv_cck_read(dev_priv, CCK_REG_DSI_PLL_CONTROL);
tmp |= DSI_PLL_VCO_EN;
/* enable DPLL ref clock */
I915_WRITE_BITS(_DPLL_A, DPLL_REFA_CLK_ENABLE_VLV,
DPLL_REFA_CLK_ENABLE_VLV);
udelay(1000);
vlv_cck_write(dev_priv, CCK_REG_DSI_PLL_CONTROL, tmp);
mutex_unlock(&dev_priv->dpio_lock);
if (wait_for(I915_READ(PIPECONF(PIPE_A)) & PIPECONF_DSI_PLL_LOCKED, 20)) {
DRM_ERROR("DSI PLL lock failed\n");
return -1;
}
DRM_DEBUG_KMS("DSI PLL locked\n");
return 0;
}
static void assert_pipe(struct drm_i915_private *dev_priv,
enum pipe pipe, bool state)
{
int reg;
u32 val;
bool cur_state;
reg = PIPECONF(pipe);
val = I915_READ(reg);
cur_state = !!(val & PIPECONF_ENABLE);
if (cur_state != state) fprintf(stderr,
"pipe %c assertion failure (expected %s, current %s)\n",
pipe_name(pipe), state_string(state), state_string(cur_state));
}
static int pipe_is_enabled(struct intel_vgpu *vgpu, int pipe)
{
struct drm_i915_private *dev_priv = vgpu->gvt->dev_priv;
if (WARN_ON(pipe < PIPE_A || pipe >= I915_MAX_PIPES))
return -EINVAL;
if (vgpu_vreg(vgpu, PIPECONF(pipe)) & PIPECONF_ENABLE)
return 1;
if (edp_pipe_is_enabled(vgpu) &&
get_edp_pipe(vgpu) == pipe)
return 1;
return 0;
}
int intel_enable_dsi_pll(struct intel_dsi *intel_dsi)
{
struct drm_i915_private *dev_priv =
intel_dsi->base.base.dev->dev_private;
/* enable DPLL ref clock */
I915_WRITE_BITS(_DPLL_A, DPLL_REFA_CLK_ENABLE_VLV,
DPLL_REFA_CLK_ENABLE_VLV);
udelay(1000); /*wait 0.5us after ungating before enabling again */
intel_cck_write32_bits(dev_priv, 0x48, 1 << 31, 1 << 31);
if (wait_for(((I915_READ(PIPECONF(intel_dsi->pipe)) & (1 << 29)) ==
(1 << 29)), 20)) {
DRM_ERROR("DSI PLL lock failed\n");
return -EIO;
}
DRM_DEBUG_KMS("DSI PLL locked\n");
return 0;
}
/**
* intel_disable_pipe - disable a pipe, asserting requirements
* @dev_priv: i915 private structure
* @pipe: pipe to disable
*
* Disable @pipe, making sure that various hardware specific requirements
* are met, if applicable, e.g. plane disabled, panel fitter off, etc.
*
* @pipe should be %PIPE_A or %PIPE_B.
*
* Will wait until the pipe has shut down before returning.
*/
static void intel_disable_pipe(struct drm_i915_private *dev_priv,
enum pipe pipe)
{
int reg;
u32 val;
/*
* Make sure planes won't keep trying to pump pixels to us,
* or we might hang the display.
*/
assert_planes_disabled(dev_priv, pipe);
/* Don't disable pipe A or pipe A PLLs if needed */
if (pipe == PIPE_A && (dev_priv->quirks & QUIRK_PIPEA_FORCE))
return;
reg = PIPECONF(pipe);
val = I915_READ(reg);
if ((val & PIPECONF_ENABLE) == 0)
return;
I915_WRITE(reg, val & ~PIPECONF_ENABLE);
intel_wait_for_pipe_off(dev_priv->dev, pipe);
}
static void intel_gma_init(const struct northbridge_intel_gm45_config *info,
u8 *mmio, u32 physbase, u16 piobase, u32 lfb)
{
int i;
u8 edid_data[128];
struct edid edid;
struct edid_mode *mode;
u32 hactive, vactive, right_border, bottom_border;
int hpolarity, vpolarity;
u32 vsync, hsync, vblank, hblank, hfront_porch, vfront_porch;
u32 candp1, candn;
u32 best_delta = 0xffffffff;
u32 target_frequency;
u32 pixel_p1 = 1;
u32 pixel_n = 1;
u32 pixel_m1 = 1;
u32 pixel_m2 = 1;
u32 link_frequency = info->gfx.link_frequency_270_mhz ? 270000 : 162000;
u32 data_m1;
u32 data_n1 = 0x00800000;
u32 link_m1;
u32 link_n1 = 0x00080000;
vga_gr_write(0x18, 0);
/* Setup GTT. */
for (i = 0; i < 0x2000; i++)
{
outl((i << 2) | 1, piobase);
outl(physbase + (i << 12) + 1, piobase + 4);
}
write32(mmio + ADPA, 0x40008c18);
write32(mmio + 0x7041c, 0x0);
write32(mmio + _DPLL_B_MD, 0x3);
vga_misc_write(0x67);
const u8 cr[] = { 0x5f, 0x4f, 0x50, 0x82, 0x55, 0x81, 0xbf, 0x1f,
0x00, 0x4f, 0x0d, 0x0e, 0x00, 0x00, 0x00, 0x00,
0x9c, 0x8e, 0x8f, 0x28, 0x1f, 0x96, 0xb9, 0xa3,
0xff
};
vga_cr_write(0x11, 0);
for (i = 0; i <= 0x18; i++)
vga_cr_write(i, cr[i]);
power_port(mmio);
intel_gmbus_read_edid(mmio + GMBUS0, 3, 0x50, edid_data, 128);
decode_edid(edid_data,
sizeof(edid_data), &edid);
mode = &edid.mode;
/* Disable screen memory to prevent garbage from appearing. */
vga_sr_write(1, vga_sr_read(1) | 0x20);
hactive = edid.x_resolution;
vactive = edid.y_resolution;
right_border = mode->hborder;
bottom_border = mode->vborder;
hpolarity = (mode->phsync == '-');
vpolarity = (mode->pvsync == '-');
vsync = mode->vspw;
hsync = mode->hspw;
vblank = mode->vbl;
hblank = mode->hbl;
hfront_porch = mode->hso;
vfront_porch = mode->vso;
target_frequency = mode->lvds_dual_channel ? mode->pixel_clock
: (2 * mode->pixel_clock);
if (IS_ENABLED(CONFIG_FRAMEBUFFER_KEEP_VESA_MODE)) {
vga_sr_write(1, 1);
vga_sr_write(0x2, 0xf);
vga_sr_write(0x3, 0x0);
vga_sr_write(0x4, 0xe);
vga_gr_write(0, 0x0);
vga_gr_write(1, 0x0);
vga_gr_write(2, 0x0);
vga_gr_write(3, 0x0);
vga_gr_write(4, 0x0);
vga_gr_write(5, 0x0);
vga_gr_write(6, 0x5);
vga_gr_write(7, 0xf);
vga_gr_write(0x10, 0x1);
vga_gr_write(0x11, 0);
edid.bytes_per_line = (edid.bytes_per_line + 63) & ~63;
write32(mmio + DSPCNTR(0), DISPPLANE_BGRX888);
write32(mmio + DSPADDR(0), 0);
write32(mmio + DSPSTRIDE(0), edid.bytes_per_line);
write32(mmio + DSPSURF(0), 0);
for (i = 0; i < 0x100; i++)
write32(mmio + LGC_PALETTE(0) + 4 * i, i * 0x010101);
} else {
vga_textmode_init();
}
/* Find suitable divisors. */
for (candp1 = 1; candp1 <= 8; candp1++) {
for (candn = 5; candn <= 10; candn++) {
u32 cur_frequency;
u32 m; /* 77 - 131. */
u32 denom; /* 35 - 560. */
u32 current_delta;
denom = candn * candp1 * 7;
/* Doesnt overflow for up to
5000000 kHz = 5 GHz. */
m = (target_frequency * denom + 60000) / 120000;
if (m < 77 || m > 131)
continue;
cur_frequency = (120000 * m) / denom;
if (target_frequency > cur_frequency)
current_delta = target_frequency - cur_frequency;
else
current_delta = cur_frequency - target_frequency;
if (best_delta > current_delta) {
best_delta = current_delta;
pixel_n = candn;
pixel_p1 = candp1;
pixel_m2 = ((m + 3) % 5) + 7;
pixel_m1 = (m - pixel_m2) / 5;
}
}
}
if (best_delta == 0xffffffff) {
printk (BIOS_ERR, "Couldn't find GFX clock divisors\n");
return;
}
link_m1 = ((uint64_t)link_n1 * mode->pixel_clock) / link_frequency;
data_m1 = ((uint64_t)data_n1 * 18 * mode->pixel_clock)
/ (link_frequency * 8 * 4);
printk(BIOS_INFO, "bringing up panel at resolution %d x %d\n",
hactive, vactive);
printk(BIOS_DEBUG, "Borders %d x %d\n",
right_border, bottom_border);
printk(BIOS_DEBUG, "Blank %d x %d\n",
hblank, vblank);
printk(BIOS_DEBUG, "Sync %d x %d\n",
hsync, vsync);
printk(BIOS_DEBUG, "Front porch %d x %d\n",
hfront_porch, vfront_porch);
printk(BIOS_DEBUG, (info->gfx.use_spread_spectrum_clock
? "Spread spectrum clock\n" : "DREF clock\n"));
printk(BIOS_DEBUG,
mode->lvds_dual_channel ? "Dual channel\n" : "Single channel\n");
printk(BIOS_DEBUG, "Polarities %d, %d\n",
hpolarity, vpolarity);
printk(BIOS_DEBUG, "Data M1=%d, N1=%d\n",
data_m1, data_n1);
printk(BIOS_DEBUG, "Link frequency %d kHz\n",
link_frequency);
printk(BIOS_DEBUG, "Link M1=%d, N1=%d\n",
link_m1, link_n1);
printk(BIOS_DEBUG, "Pixel N=%d, M1=%d, M2=%d, P1=%d\n",
pixel_n, pixel_m1, pixel_m2, pixel_p1);
printk(BIOS_DEBUG, "Pixel clock %d kHz\n",
120000 * (5 * pixel_m1 + pixel_m2) / pixel_n
/ (pixel_p1 * 7));
write32(mmio + LVDS,
(hpolarity << 20) | (vpolarity << 21)
| (mode->lvds_dual_channel ? LVDS_CLOCK_B_POWERUP_ALL
| LVDS_CLOCK_BOTH_POWERUP_ALL : 0)
| LVDS_BORDER_ENABLE | LVDS_CLOCK_A_POWERUP_ALL);
mdelay(1);
write32(mmio + PP_CONTROL, PANEL_UNLOCK_REGS
| (read32(mmio + PP_CONTROL) & ~PANEL_UNLOCK_MASK));
write32(mmio + FP0(0),
((pixel_n - 2) << 16)
| ((pixel_m1 - 2) << 8) | pixel_m2);
write32(mmio + DPLL(0),
DPLL_VCO_ENABLE | DPLLB_MODE_LVDS
| (mode->lvds_dual_channel ? DPLLB_LVDS_P2_CLOCK_DIV_7
: DPLLB_LVDS_P2_CLOCK_DIV_14)
| (0x10000 << (pixel_p1 - 1))
| ((info->gfx.use_spread_spectrum_clock ? 3 : 0) << 13)
| (0x1 << (pixel_p1 - 1)));
mdelay(1);
write32(mmio + DPLL(0),
DPLL_VCO_ENABLE | DPLLB_MODE_LVDS
| (mode->lvds_dual_channel ? DPLLB_LVDS_P2_CLOCK_DIV_7
: DPLLB_LVDS_P2_CLOCK_DIV_14)
| (0x10000 << (pixel_p1 - 1))
| ((info->gfx.use_spread_spectrum_clock ? 3 : 0) << 13)
| (0x1 << (pixel_p1 - 1)));
/* Re-lock the registers. */
write32(mmio + PP_CONTROL,
(read32(mmio + PP_CONTROL) & ~PANEL_UNLOCK_MASK));
write32(mmio + LVDS,
(hpolarity << 20) | (vpolarity << 21)
| (mode->lvds_dual_channel ? LVDS_CLOCK_B_POWERUP_ALL
| LVDS_CLOCK_BOTH_POWERUP_ALL : 0)
| LVDS_BORDER_ENABLE | LVDS_CLOCK_A_POWERUP_ALL);
write32(mmio + HTOTAL(0),
((hactive + right_border + hblank - 1) << 16)
| (hactive - 1));
write32(mmio + HBLANK(0),
((hactive + right_border + hblank - 1) << 16)
| (hactive + right_border - 1));
write32(mmio + HSYNC(0),
((hactive + right_border + hfront_porch + hsync - 1) << 16)
| (hactive + right_border + hfront_porch - 1));
write32(mmio + VTOTAL(0), ((vactive + bottom_border + vblank - 1) << 16)
| (vactive - 1));
write32(mmio + VBLANK(0), ((vactive + bottom_border + vblank - 1) << 16)
| (vactive + bottom_border - 1));
write32(mmio + VSYNC(0),
(vactive + bottom_border + vfront_porch + vsync - 1)
| (vactive + bottom_border + vfront_porch - 1));
write32(mmio + PIPECONF(0), PIPECONF_DISABLE);
write32(mmio + PF_WIN_POS(0), 0);
if (IS_ENABLED(CONFIG_FRAMEBUFFER_KEEP_VESA_MODE)) {
write32(mmio + PIPESRC(0), ((hactive - 1) << 16)
| (vactive - 1));
write32(mmio + PF_CTL(0), 0);
write32(mmio + PF_WIN_SZ(0), 0);
write32(mmio + PFIT_CONTROL, 0x20000000);
} else {
write32(mmio + PIPESRC(0), (639 << 16) | 399);
write32(mmio + PF_CTL(0), PF_ENABLE | PF_FILTER_MED_3x3);
write32(mmio + PF_WIN_SZ(0), vactive | (hactive << 16));
write32(mmio + PFIT_CONTROL, 0xa0000000);
}
mdelay(1);
write32(mmio + PIPE_DATA_M1(0), 0x7e000000 | data_m1);
write32(mmio + PIPE_DATA_N1(0), data_n1);
write32(mmio + PIPE_LINK_M1(0), link_m1);
write32(mmio + PIPE_LINK_N1(0), link_n1);
write32(mmio + 0x000f000c, 0x00002040);
mdelay(1);
write32(mmio + 0x000f000c, 0x00002050);
write32(mmio + 0x00060100, 0x00044000);
mdelay(1);
write32(mmio + PIPECONF(0), PIPECONF_BPP_6);
write32(mmio + 0x000f0008, 0x00000040);
write32(mmio + 0x000f000c, 0x00022050);
write32(mmio + PIPECONF(0), PIPECONF_BPP_6 | PIPECONF_DITHER_EN);
write32(mmio + PIPECONF(0), PIPECONF_ENABLE | PIPECONF_BPP_6 | PIPECONF_DITHER_EN);
if (IS_ENABLED(CONFIG_FRAMEBUFFER_KEEP_VESA_MODE)) {
write32(mmio + VGACNTRL, 0x22c4008e | VGA_DISP_DISABLE);
write32(mmio + DSPCNTR(0), DISPLAY_PLANE_ENABLE
| DISPPLANE_BGRX888);
mdelay(1);
} else {
write32(mmio + VGACNTRL, 0x22c4008e);
}
write32(mmio + TRANS_HTOTAL(0),
((hactive + right_border + hblank - 1) << 16)
| (hactive - 1));
write32(mmio + TRANS_HBLANK(0),
((hactive + right_border + hblank - 1) << 16)
| (hactive + right_border - 1));
write32(mmio + TRANS_HSYNC(0),
((hactive + right_border + hfront_porch + hsync - 1) << 16)
| (hactive + right_border + hfront_porch - 1));
write32(mmio + TRANS_VTOTAL(0),
((vactive + bottom_border + vblank - 1) << 16)
| (vactive - 1));
write32(mmio + TRANS_VBLANK(0),
((vactive + bottom_border + vblank - 1) << 16)
| (vactive + bottom_border - 1));
write32(mmio + TRANS_VSYNC(0),
(vactive + bottom_border + vfront_porch + vsync - 1)
| (vactive + bottom_border + vfront_porch - 1));
write32(mmio + 0x00060100, 0xb01c4000);
write32(mmio + 0x000f000c, 0xb01a2050);
mdelay(1);
write32(mmio + TRANSCONF(0), TRANS_ENABLE | TRANS_6BPC
);
write32(mmio + LVDS,
LVDS_PORT_ENABLE
| (hpolarity << 20) | (vpolarity << 21)
| (mode->lvds_dual_channel ? LVDS_CLOCK_B_POWERUP_ALL
| LVDS_CLOCK_BOTH_POWERUP_ALL : 0)
| LVDS_BORDER_ENABLE | LVDS_CLOCK_A_POWERUP_ALL);
write32(mmio + PP_CONTROL, PANEL_POWER_ON | PANEL_POWER_RESET);
/* Enable screen memory. */
vga_sr_write(1, vga_sr_read(1) & ~0x20);
/* Clear interrupts. */
write32(mmio + DEIIR, 0xffffffff);
write32(mmio + SDEIIR, 0xffffffff);
if (IS_ENABLED(CONFIG_FRAMEBUFFER_KEEP_VESA_MODE)) {
memset((void *) lfb, 0,
edid.x_resolution * edid.y_resolution * 4);
set_vbe_mode_info_valid(&edid, lfb);
}
}
static void intel_gma_init(const struct northbridge_intel_x4x_config *info,
u8 *mmio, u32 physbase, u16 piobase, u32 lfb)
{
int i;
u8 edid_data[128];
struct edid edid;
struct edid_mode *mode;
u8 edid_is_found;
/* Initialise mode variables for 640 x 480 @ 60Hz */
u32 hactive = 640, vactive = 480;
u32 right_border = 0, bottom_border = 0;
int hpolarity = 0, vpolarity = 0;
u32 hsync = 96, vsync = 2;
u32 hblank = 160, vblank = 45;
u32 hfront_porch = 16, vfront_porch = 10;
u32 target_frequency = 25175;
u32 err_most = 0xffffffff;
u32 pixel_p1 = 1;
u32 pixel_p2;
u32 pixel_n = 1;
u32 pixel_m1 = 1;
u32 pixel_m2 = 1;
vga_gr_write(0x18, 0);
/* Set up GTT */
for (i = 0; i < 0x1000; i++) {
outl((i << 2) | 1, piobase);
outl(physbase + (i << 12) + 1, piobase + 4);
}
write32(mmio + VGA0, 0x31108);
write32(mmio + VGA1, 0x31406);
write32(mmio + ADPA, ADPA_DAC_ENABLE
| ADPA_PIPE_A_SELECT
| ADPA_CRT_HOTPLUG_MONITOR_COLOR
| ADPA_CRT_HOTPLUG_ENABLE
| ADPA_USE_VGA_HVPOLARITY
| ADPA_VSYNC_CNTL_ENABLE
| ADPA_HSYNC_CNTL_ENABLE
| ADPA_DPMS_ON
);
write32(mmio + 0x7041c, 0x0);
write32(mmio + DPLL_MD(0), 0x3);
write32(mmio + DPLL_MD(1), 0x3);
vga_misc_write(0x67);
const u8 cr[] = { 0x5f, 0x4f, 0x50, 0x82, 0x55, 0x81, 0xbf, 0x1f,
0x00, 0x4f, 0x0d, 0x0e, 0x00, 0x00, 0x00, 0x00,
0x9c, 0x8e, 0x8f, 0x28, 0x1f, 0x96, 0xb9, 0xa3,
0xff
};
vga_cr_write(0x11, 0);
for (i = 0; i <= 0x18; i++)
vga_cr_write(i, cr[i]);
udelay(1);
intel_gmbus_read_edid(mmio + GMBUS0, 2, 0x50, edid_data,
sizeof(edid_data));
intel_gmbus_stop(mmio + GMBUS0);
decode_edid(edid_data,
sizeof(edid_data), &edid);
mode = &edid.mode;
/* Disable screen memory to prevent garbage from appearing. */
vga_sr_write(1, vga_sr_read(1) | 0x20);
edid_is_found = edid_is_present(edid_data, sizeof(edid_data));
if (edid_is_found) {
printk(BIOS_DEBUG, "EDID is not null");
hactive = edid.x_resolution;
vactive = edid.y_resolution;
right_border = mode->hborder;
bottom_border = mode->vborder;
hpolarity = (mode->phsync == '-');
vpolarity = (mode->pvsync == '-');
vsync = mode->vspw;
hsync = mode->hspw;
vblank = mode->vbl;
hblank = mode->hbl;
hfront_porch = mode->hso;
vfront_porch = mode->vso;
target_frequency = mode->pixel_clock;
} else
printk(BIOS_DEBUG, "EDID is null, using 640 x 480 @ 60Hz mode");
if (IS_ENABLED(CONFIG_FRAMEBUFFER_KEEP_VESA_MODE)) {
vga_sr_write(1, 1);
vga_sr_write(0x2, 0xf);
vga_sr_write(0x3, 0x0);
vga_sr_write(0x4, 0xe);
vga_gr_write(0, 0x0);
vga_gr_write(1, 0x0);
vga_gr_write(2, 0x0);
vga_gr_write(3, 0x0);
vga_gr_write(4, 0x0);
vga_gr_write(5, 0x0);
vga_gr_write(6, 0x5);
vga_gr_write(7, 0xf);
vga_gr_write(0x10, 0x1);
vga_gr_write(0x11, 0);
edid.bytes_per_line = (edid.bytes_per_line + 63) & ~63;
write32(mmio + DSPCNTR(0), DISPLAY_PLANE_ENABLE
| DISPPLANE_BGRX888);
write32(mmio + DSPADDR(0), 0);
write32(mmio + DSPSTRIDE(0), edid.bytes_per_line);
write32(mmio + DSPSURF(0), 0);
for (i = 0; i < 0x100; i++)
write32(mmio + LGC_PALETTE(0) + 4 * i, i * 0x010101);
} else {
vga_textmode_init();
}
pixel_p2 = target_frequency <= 225000 ? 10 : 5;
u32 candn, candm1, candm2, candp1;
for (candn = 1; candn <= 4; candn++) {
for (candm1 = 23; candm1 >= 16; candm1--) {
for (candm2 = 11; candm2 >= 5; candm2--) {
for (candp1 = 8; candp1 >= 1; candp1--) {
u32 m = 5 * (candm1 + 2) + (candm2 + 2);
u32 p = candp1 * pixel_p2;
u32 vco = DIV_ROUND_CLOSEST(
BASE_FREQUENCY * m, candn + 2);
u32 dot = DIV_ROUND_CLOSEST(vco, p);
u32 this_err = MAX(dot, target_frequency) -
MIN(dot, target_frequency);
if (this_err < err_most) {
err_most = this_err;
pixel_n = candn;
pixel_m1 = candm1;
pixel_m2 = candm2;
pixel_p1 = candp1;
}
}
}
}
}
if (err_most == 0xffffffff) {
printk(BIOS_ERR, "Couldn't find GFX clock divisors\n");
return;
}
printk(BIOS_INFO, "bringing up panel at resolution %d x %d\n",
hactive, vactive);
printk(BIOS_DEBUG, "Borders %d x %d\n",
right_border, bottom_border);
printk(BIOS_DEBUG, "Blank %d x %d\n",
hblank, vblank);
printk(BIOS_DEBUG, "Sync %d x %d\n",
hsync, vsync);
printk(BIOS_DEBUG, "Front porch %d x %d\n",
hfront_porch, vfront_porch);
printk(BIOS_DEBUG, (info->gfx.use_spread_spectrum_clock
? "Spread spectrum clock\n" : "DREF clock\n"));
printk(BIOS_DEBUG, "Polarities %d, %d\n",
hpolarity, vpolarity);
printk(BIOS_DEBUG, "Pixel N=%d, M1=%d, M2=%d, P1=%d, P2=%d\n",
pixel_n, pixel_m1, pixel_m2, pixel_p1, pixel_p2);
printk(BIOS_DEBUG, "Pixel clock %d kHz\n",
BASE_FREQUENCY * (5 * (pixel_m1 + 2) + (pixel_m2 + 2)) /
(pixel_n + 2) / (pixel_p1 * pixel_p2));
mdelay(1);
write32(mmio + FP0(0), (pixel_n << 16)
| (pixel_m1 << 8) | pixel_m2);
write32(mmio + DPLL(0), DPLL_VCO_ENABLE
| DPLL_VGA_MODE_DIS | DPLLB_MODE_DAC_SERIAL
| (pixel_p2 == 10 ? DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 :
DPLL_DAC_SERIAL_P2_CLOCK_DIV_5)
| (0x10000 << (pixel_p1 - 1))
| (6 << 9));
mdelay(1);
write32(mmio + DPLL(0), DPLL_VCO_ENABLE
| DPLL_VGA_MODE_DIS | DPLLB_MODE_DAC_SERIAL
| (pixel_p2 == 10 ? DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 :
DPLL_DAC_SERIAL_P2_CLOCK_DIV_5)
| (0x10000 << (pixel_p1 - 1))
| (6 << 9));
write32(mmio + ADPA, ADPA_DAC_ENABLE
| ADPA_PIPE_A_SELECT
| ADPA_CRT_HOTPLUG_MONITOR_COLOR
| ADPA_CRT_HOTPLUG_ENABLE
| ADPA_VSYNC_CNTL_ENABLE
| ADPA_HSYNC_CNTL_ENABLE
| ADPA_DPMS_ON
| (vpolarity ? ADPA_VSYNC_ACTIVE_LOW :
ADPA_VSYNC_ACTIVE_HIGH)
| (hpolarity ? ADPA_HSYNC_ACTIVE_LOW :
ADPA_HSYNC_ACTIVE_HIGH));
write32(mmio + HTOTAL(0),
((hactive + right_border + hblank - 1) << 16)
| (hactive - 1));
write32(mmio + HBLANK(0),
((hactive + right_border + hblank - 1) << 16)
| (hactive + right_border - 1));
write32(mmio + HSYNC(0),
((hactive + right_border + hfront_porch + hsync - 1) << 16)
| (hactive + right_border + hfront_porch - 1));
write32(mmio + VTOTAL(0), ((vactive + bottom_border + vblank - 1) << 16)
| (vactive - 1));
write32(mmio + VBLANK(0), ((vactive + bottom_border + vblank - 1) << 16)
| (vactive + bottom_border - 1));
write32(mmio + VSYNC(0),
((vactive + bottom_border + vfront_porch + vsync - 1) << 16)
| (vactive + bottom_border + vfront_porch - 1));
write32(mmio + PIPECONF(0), PIPECONF_DISABLE);
write32(mmio + PF_WIN_POS(0), 0);
if (IS_ENABLED(CONFIG_FRAMEBUFFER_KEEP_VESA_MODE)) {
write32(mmio + PIPESRC(0), ((hactive - 1) << 16)
| (vactive - 1));
write32(mmio + PF_CTL(0), 0);
write32(mmio + PF_WIN_SZ(0), 0);
write32(mmio + PFIT_CONTROL, 0);
} else {
write32(mmio + PIPESRC(0), (639 << 16) | 399);
write32(mmio + PF_CTL(0), PF_ENABLE | PF_FILTER_MED_3x3);
write32(mmio + PF_WIN_SZ(0), vactive | (hactive << 16));
write32(mmio + PFIT_CONTROL, 0x80000000);
}
mdelay(1);
write32(mmio + PIPECONF(0), PIPECONF_BPP_6);
write32(mmio + PIPECONF(0), PIPECONF_BPP_6 | PIPECONF_DITHER_EN);
write32(mmio + PIPECONF(0), PIPECONF_ENABLE
| PIPECONF_BPP_6 | PIPECONF_DITHER_EN);
if (IS_ENABLED(CONFIG_FRAMEBUFFER_KEEP_VESA_MODE)) {
write32(mmio + VGACNTRL, VGA_DISP_DISABLE);
write32(mmio + DSPCNTR(0), DISPLAY_PLANE_ENABLE
| DISPPLANE_BGRX888);
mdelay(1);
} else {
write32(mmio + VGACNTRL, 0xc4008e);
}
write32(mmio + ADPA, ADPA_DAC_ENABLE
| ADPA_PIPE_A_SELECT
| ADPA_CRT_HOTPLUG_MONITOR_COLOR
| ADPA_CRT_HOTPLUG_ENABLE
| ADPA_VSYNC_CNTL_ENABLE
| ADPA_HSYNC_CNTL_ENABLE
| ADPA_DPMS_ON
| (vpolarity ? ADPA_VSYNC_ACTIVE_LOW :
ADPA_VSYNC_ACTIVE_HIGH)
| (hpolarity ? ADPA_HSYNC_ACTIVE_LOW :
ADPA_HSYNC_ACTIVE_HIGH));
write32(mmio + PP_CONTROL, PANEL_POWER_ON | PANEL_POWER_RESET);
/* Enable screen memory. */
vga_sr_write(1, vga_sr_read(1) & ~0x20);
/* Clear interrupts. */
write32(mmio + DEIIR, 0xffffffff);
write32(mmio + SDEIIR, 0xffffffff);
if (IS_ENABLED(CONFIG_FRAMEBUFFER_KEEP_VESA_MODE)) {
memset((void *) lfb, 0,
hactive * vactive * 4);
set_vbe_mode_info_valid(&edid, lfb);
}
}
static int intel_gma_init(struct northbridge_intel_i945_config *conf,
unsigned int pphysbase, unsigned int piobase,
void *pmmio, unsigned int pgfx)
{
struct edid edid;
u8 edid_data[128];
unsigned long temp;
int hpolarity, vpolarity;
u32 candp1, candn;
u32 best_delta = 0xffffffff;
u32 target_frequency;
u32 pixel_p1 = 1;
u32 pixel_n = 1;
u32 pixel_m1 = 1;
u32 pixel_m2 = 1;
u32 hactive, vactive, right_border, bottom_border;
u32 vsync, hsync, vblank, hblank, hfront_porch, vfront_porch;
u32 i, j;
u32 uma_size;
u16 reg16;
printk(BIOS_SPEW,
"i915lightup: graphics %p mmio %p addrport %04x physbase %08x\n",
(void *)pgfx, pmmio, piobase, pphysbase);
intel_gmbus_read_edid(pmmio + GMBUS0, 3, 0x50, edid_data, 128);
decode_edid(edid_data, sizeof(edid_data), &edid);
hpolarity = (edid.phsync == '-');
vpolarity = (edid.pvsync == '-');
hactive = edid.x_resolution;
vactive = edid.y_resolution;
right_border = edid.hborder;
bottom_border = edid.vborder;
vblank = edid.vbl;
hblank = edid.hbl;
vsync = edid.vspw;
hsync = edid.hspw;
hfront_porch = edid.hso;
vfront_porch = edid.vso;
for (i = 0; i < 2; i++)
for (j = 0; j < 0x100; j++)
/* R=j, G=j, B=j. */
write32(pmmio + PALETTE(i) + 4 * j, 0x10101 * j);
write32(pmmio + PCH_PP_CONTROL, PANEL_UNLOCK_REGS
| (read32(pmmio + PCH_PP_CONTROL) & ~PANEL_UNLOCK_MASK));
write32(pmmio + MI_ARB_STATE, MI_ARB_C3_LP_WRITE_ENABLE | (1 << 27));
/* Clean registers. */
for (i = 0; i < 0x20; i += 4)
write32(pmmio + RENDER_RING_BASE + i, 0);
for (i = 0; i < 0x20; i += 4)
write32(pmmio + FENCE_REG_965_0 + i, 0);
write32(pmmio + PP_ON_DELAYS, 0);
write32(pmmio + PP_OFF_DELAYS, 0);
/* Disable VGA. */
write32(pmmio + VGACNTRL, VGA_DISP_DISABLE);
/* Disable pipes. */
write32(pmmio + PIPECONF(0), 0);
write32(pmmio + PIPECONF(1), 0);
/* Init PRB0. */
write32(pmmio + HWS_PGA, 0x352d2000);
write32(pmmio + PRB0_CTL, 0);
write32(pmmio + PRB0_HEAD, 0);
write32(pmmio + PRB0_TAIL, 0);
write32(pmmio + PRB0_START, 0);
write32(pmmio + PRB0_CTL, 0x0001f001);
write32(pmmio + D_STATE, DSTATE_PLL_D3_OFF
| DSTATE_GFX_CLOCK_GATING | DSTATE_DOT_CLOCK_GATING);
write32(pmmio + ECOSKPD, 0x00010000);
write32(pmmio + HWSTAM, 0xeffe);
write32(pmmio + PORT_HOTPLUG_EN, conf->gpu_hotplug);
write32(pmmio + INSTPM, 0x08000000 | INSTPM_AGPBUSY_DIS);
target_frequency = conf->gpu_lvds_is_dual_channel ? edid.pixel_clock
: (2 * edid.pixel_clock);
/* Find suitable divisors. */
for (candp1 = 1; candp1 <= 8; candp1++) {
for (candn = 5; candn <= 10; candn++) {
u32 cur_frequency;
u32 m; /* 77 - 131. */
u32 denom; /* 35 - 560. */
u32 current_delta;
denom = candn * candp1 * 7;
/* Doesnt overflow for up to
5000000 kHz = 5 GHz. */
m = (target_frequency * denom
+ BASE_FREQUENCY / 2) / BASE_FREQUENCY;
if (m < 77 || m > 131)
continue;
cur_frequency = (BASE_FREQUENCY * m) / denom;
if (target_frequency > cur_frequency)
current_delta = target_frequency - cur_frequency;
else
current_delta = cur_frequency - target_frequency;
if (best_delta > current_delta) {
best_delta = current_delta;
pixel_n = candn;
pixel_p1 = candp1;
pixel_m2 = ((m + 3) % 5) + 7;
pixel_m1 = (m - pixel_m2) / 5;
}
}
}
if (best_delta == 0xffffffff) {
printk (BIOS_ERR, "Couldn't find GFX clock divisors\n");
return -1;
}
printk(BIOS_INFO, "bringing up panel at resolution %d x %d\n",
hactive, vactive);
printk(BIOS_DEBUG, "Borders %d x %d\n", right_border, bottom_border);
printk(BIOS_DEBUG, "Blank %d x %d\n", hblank, vblank);
printk(BIOS_DEBUG, "Sync %d x %d\n", hsync, vsync);
printk(BIOS_DEBUG, "Front porch %d x %d\n", hfront_porch, vfront_porch);
printk(BIOS_DEBUG, (conf->gpu_lvds_use_spread_spectrum_clock
? "Spread spectrum clock\n"
: "DREF clock\n"));
printk(BIOS_DEBUG, (conf->gpu_lvds_is_dual_channel
? "Dual channel\n"
: "Single channel\n"));
printk(BIOS_DEBUG, "Polarities %d, %d\n",
hpolarity, vpolarity);
printk(BIOS_DEBUG, "Pixel N=%d, M1=%d, M2=%d, P1=%d\n",
pixel_n, pixel_m1, pixel_m2, pixel_p1);
printk(BIOS_DEBUG, "Pixel clock %d kHz\n",
BASE_FREQUENCY * (5 * pixel_m1 + pixel_m2) / pixel_n
/ (pixel_p1 * 7));
#if !IS_ENABLED(CONFIG_FRAMEBUFFER_KEEP_VESA_MODE)
write32(pmmio + PF_WIN_SZ(0), vactive | (hactive << 16));
write32(pmmio + PF_WIN_POS(0), 0);
write32(pmmio + PF_CTL(0),PF_ENABLE | PF_FILTER_MED_3x3);
write32(pmmio + PFIT_CONTROL, PFIT_ENABLE | (1 << PFIT_PIPE_SHIFT) | HORIZ_AUTO_SCALE | VERT_AUTO_SCALE);
#else
/* Disable panel fitter (we're in native resolution). */
write32(pmmio + PF_CTL(0), 0);
write32(pmmio + PF_WIN_SZ(0), 0);
write32(pmmio + PF_WIN_POS(0), 0);
write32(pmmio + PFIT_PGM_RATIOS, 0);
write32(pmmio + PFIT_CONTROL, 0);
#endif
mdelay(1);
write32(pmmio + DSPCNTR(0), DISPPLANE_BGRX888
| DISPPLANE_SEL_PIPE_B | DISPPLANE_GAMMA_ENABLE);
mdelay(1);
write32(pmmio + PP_CONTROL, PANEL_UNLOCK_REGS
| (read32(pmmio + PP_CONTROL) & ~PANEL_UNLOCK_MASK));
write32(pmmio + FP0(1),
((pixel_n - 2) << 16)
| ((pixel_m1 - 2) << 8) | pixel_m2);
write32(pmmio + DPLL(1),
DPLL_VGA_MODE_DIS |
DPLL_VCO_ENABLE | DPLLB_MODE_LVDS
| (conf->gpu_lvds_is_dual_channel ? DPLLB_LVDS_P2_CLOCK_DIV_7
: DPLLB_LVDS_P2_CLOCK_DIV_14)
| (conf->gpu_lvds_use_spread_spectrum_clock
? DPLL_INTEGRATED_CLOCK_VLV | DPLL_INTEGRATED_CRI_CLK_VLV
: 0)
| (pixel_p1 << 16)
| (pixel_p1));
mdelay(1);
write32(pmmio + DPLL(1),
DPLL_VGA_MODE_DIS |
DPLL_VCO_ENABLE | DPLLB_MODE_LVDS
| (conf->gpu_lvds_is_dual_channel ? DPLLB_LVDS_P2_CLOCK_DIV_7
: DPLLB_LVDS_P2_CLOCK_DIV_14)
| ((conf->gpu_lvds_use_spread_spectrum_clock ? 3 : 0) << 13)
| (pixel_p1 << 16)
| (pixel_p1));
mdelay(1);
write32(pmmio + HTOTAL(1),
((hactive + right_border + hblank - 1) << 16)
| (hactive - 1));
write32(pmmio + HBLANK(1),
((hactive + right_border + hblank - 1) << 16)
| (hactive + right_border - 1));
write32(pmmio + HSYNC(1),
((hactive + right_border + hfront_porch + hsync - 1) << 16)
| (hactive + right_border + hfront_porch - 1));
write32(pmmio + VTOTAL(1), ((vactive + bottom_border + vblank - 1) << 16)
| (vactive - 1));
write32(pmmio + VBLANK(1), ((vactive + bottom_border + vblank - 1) << 16)
| (vactive + bottom_border - 1));
write32(pmmio + VSYNC(1),
(vactive + bottom_border + vfront_porch + vsync - 1)
| (vactive + bottom_border + vfront_porch - 1));
#if !IS_ENABLED(CONFIG_FRAMEBUFFER_KEEP_VESA_MODE)
write32(pmmio + PIPESRC(1), (639 << 16) | 399);
#else
write32(pmmio + PIPESRC(1), ((hactive - 1) << 16) | (vactive - 1));
#endif
mdelay(1);
write32(pmmio + DSPSIZE(0), (hactive - 1) | ((vactive - 1) << 16));
write32(pmmio + DSPPOS(0), 0);
/* Backlight init. */
write32(pmmio + FW_BLC_SELF, FW_BLC_SELF_EN_MASK);
write32(pmmio + FW_BLC, 0x011d011a);
write32(pmmio + FW_BLC2, 0x00000102);
write32(pmmio + FW_BLC_SELF, FW_BLC_SELF_EN_MASK);
write32(pmmio + FW_BLC_SELF, 0x0001003f);
write32(pmmio + FW_BLC, 0x011d0109);
write32(pmmio + FW_BLC2, 0x00000102);
write32(pmmio + FW_BLC_SELF, FW_BLC_SELF_EN_MASK);
write32(pmmio + BLC_PWM_CTL, conf->gpu_backlight);
edid.bytes_per_line = (edid.bytes_per_line + 63) & ~63;
write32(pmmio + DSPADDR(0), 0);
write32(pmmio + DSPSURF(0), 0);
write32(pmmio + DSPSTRIDE(0), edid.bytes_per_line);
write32(pmmio + DSPCNTR(0), DISPLAY_PLANE_ENABLE | DISPPLANE_BGRX888
| DISPPLANE_SEL_PIPE_B | DISPPLANE_GAMMA_ENABLE);
mdelay(1);
write32(pmmio + PIPECONF(1), PIPECONF_ENABLE);
write32(pmmio + LVDS, LVDS_ON
| (hpolarity << 20) | (vpolarity << 21)
| (conf->gpu_lvds_is_dual_channel ? LVDS_CLOCK_B_POWERUP_ALL
| LVDS_CLOCK_BOTH_POWERUP_ALL : 0)
| LVDS_CLOCK_A_POWERUP_ALL
| LVDS_PIPE(1));
write32(pmmio + PP_CONTROL, PANEL_UNLOCK_REGS | PANEL_POWER_OFF);
write32(pmmio + PP_CONTROL, PANEL_UNLOCK_REGS | PANEL_POWER_RESET);
mdelay(1);
write32(pmmio + PP_CONTROL, PANEL_UNLOCK_REGS
| PANEL_POWER_ON | PANEL_POWER_RESET);
printk (BIOS_DEBUG, "waiting for panel powerup\n");
while (1) {
u32 reg32;
reg32 = read32(pmmio + PP_STATUS);
if ((reg32 & PP_SEQUENCE_MASK) == PP_SEQUENCE_NONE)
break;
}
printk (BIOS_DEBUG, "panel powered up\n");
write32(pmmio + PP_CONTROL, PANEL_POWER_ON | PANEL_POWER_RESET);
/* Clear interrupts. */
write32(pmmio + DEIIR, 0xffffffff);
write32(pmmio + SDEIIR, 0xffffffff);
write32(pmmio + IIR, 0xffffffff);
write32(pmmio + IMR, 0xffffffff);
write32(pmmio + EIR, 0xffffffff);
if (gtt_setup(pmmio)) {
printk(BIOS_ERR, "ERROR: GTT Setup Failed!!!\n");
return 0;
}
/* Setup GTT. */
reg16 = pci_read_config16(dev_find_slot(0, PCI_DEVFN(0, 0)), GGC);
uma_size = 0;
if (!(reg16 & 2)) {
reg16 >>= 4;
reg16 &= 7;
switch (reg16) {
case 1:
uma_size = 1024;
break;
case 3:
uma_size = 8192;
break;
}
printk(BIOS_DEBUG, "%dM UMA\n", uma_size >> 10);
}
void runio(struct intel_dp *dp)
{
u8 read_val;
intel_dp_wait_panel_power_control(0xabcd0008);
/* vbios spins at this point. Some haswell weirdness? */
intel_dp_wait_panel_power_control(0xabcd0008);
/* This should be a function like intel_panel_enable_backlight
However, we are not sure how the value 0x3a9 comes up.
It has to do something with PWM frequency */
gtt_write(BLC_PWM_CPU_CTL,0x03a903a9);
gtt_write(BLC_PWM_PCH_CTL2,0x03a903a9);
gtt_write(BLC_PWM_PCH_CTL1,BLM_PCH_PWM_ENABLE);
gtt_write(DEIIR,0x00008000);
intel_dp_wait_reg(DEIIR, 0x00000000);
gtt_write(DSPSTRIDE(dp->plane),dp->stride);
intel_dp_sink_dpms(dp, 0);
intel_dp_get_max_downspread(dp, &read_val);
intel_dp_set_m_n_regs(dp);
intel_dp_set_resolution(dp);
gtt_write(PIPESRC(dp->pipe),dp->pipesrc);
gtt_write(PIPECONF(dp->transcoder),0x00000000);
gtt_write(PCH_TRANSCONF(dp->pipe),0x00000000);
mainboard_set_port_clk_dp(dp);
gtt_write(DSPSTRIDE(dp->plane),dp->stride);
gtt_write(DSPCNTR(dp->plane),DISPLAY_PLANE_ENABLE|DISPPLANE_BGRX888);
gtt_write(DEIIR,0x00000080);
gtt_write(TRANS_DDI_FUNC_CTL_EDP,dp->flags);
gtt_write(PIPECONF(dp->transcoder),PIPECONF_ENABLE|PIPECONF_DITHER_EN);
intel_dp_wait_panel_power_control(0xabcd000a);
/* what is this doing? Not sure yet. */
intel_dp_i2c_write(dp, 0x0);
intel_dp_i2c_read(dp, &read_val);
intel_dp_i2c_write(dp, 0x04);
intel_dp_i2c_read(dp, &read_val);
intel_dp_i2c_write(dp, 0x7e);
intel_dp_i2c_read(dp, &read_val);
/* this needs to be a call to a function */
gtt_write(DP_A, DP_LINK_TRAIN_PAT_1 | DP_LINK_TRAIN_PAT_1_CPT | DP_VOLTAGE_0_4 | DP_PRE_EMPHASIS_0 | DP_PORT_WIDTH_1 | DP_PLL_FREQ_270MHZ | DP_SCRAMBLING_DISABLE_IRONLAKE | DP_SYNC_VS_HIGH |0x00000091);
gtt_write(DP_TP_CTL(dp->port),DP_TP_CTL_ENABLE | DP_TP_CTL_ENHANCED_FRAME_ENABLE);
gtt_write(DP_A, DP_PORT_EN | DP_LINK_TRAIN_PAT_1 | DP_LINK_TRAIN_PAT_1_CPT | DP_VOLTAGE_0_4 | DP_PRE_EMPHASIS_0 | DP_PORT_WIDTH_1 | DP_ENHANCED_FRAMING | DP_PLL_FREQ_270MHZ | DP_SCRAMBLING_DISABLE_IRONLAKE | DP_SYNC_VS_HIGH |0x80040091);
/* we may need to move these *after* power well power up and *before* PCH_PP_CONTROL in gma.c */
gtt_write(PCH_PP_ON_DELAYS, PANEL_PORT_SELECT_LVDS |(/* PANEL_POWER_UP_DELAY_MASK */0x1<<16)|(/* PANEL_LIGHT_ON_DELAY_MASK */0xa<<0)|0x0001000a);
gtt_write(PCH_PP_ON_DELAYS, PANEL_PORT_SELECT_LVDS |(/* PANEL_POWER_UP_DELAY_MASK */0x7d0<<16)|(/* PANEL_LIGHT_ON_DELAY_MASK */0xa<<0)|0x07d0000a);
intel_dp_set_bw(dp);
intel_dp_set_lane_count(dp);
mainboard_train_link(dp);
/* need a function: intel_ddi_set_tp or similar */
gtt_write(DP_TP_CTL(dp->port),DP_TP_CTL_ENABLE | DP_TP_CTL_ENHANCED_FRAME_ENABLE | DP_TP_CTL_LINK_TRAIN_IDLE);
gtt_write(DP_TP_CTL(dp->port),DP_TP_CTL_ENABLE | DP_TP_CTL_ENHANCED_FRAME_ENABLE | DP_TP_CTL_LINK_TRAIN_NORMAL);
gtt_write(BLC_PWM_CPU_CTL,0x03a903a9);
gtt_write(BLC_PWM_PCH_CTL2,0x03a903a9);
gtt_write(BLC_PWM_PCH_CTL1,0x80000000);
/* some of this is not needed. */
gtt_write(DIGITAL_PORT_HOTPLUG_CNTRL, DIGITAL_PORTA_HOTPLUG_ENABLE );
gtt_write(SDEIIR,0x00000000);
gtt_write(DEIIR,0x00000000);
gtt_write(DEIIR,0x00008000);
intel_dp_wait_reg(DEIIR, 0x00000000);
gtt_write(DSPSTRIDE(dp->plane),dp->stride);
gtt_write(PIPESRC(dp->pipe),dp->pipesrc);
gtt_write(DEIIR,0x00000080);
intel_dp_wait_reg(DEIIR, 0x00000000);
gtt_write(DSPSTRIDE(dp->plane),dp->stride);
gtt_write(DSPCNTR(dp->plane),DISPLAY_PLANE_ENABLE | DISPPLANE_BGRX888);
gtt_write(PCH_PP_CONTROL,EDP_BLC_ENABLE | PANEL_POWER_RESET | PANEL_POWER_ON);
gtt_write(SDEIIR,0x00000000);
gtt_write(SDEIIR,0x00000000);
gtt_write(DEIIR,0x00000000);
}
static int
intel_update_plane(struct drm_plane *plane, struct drm_crtc *crtc,
struct drm_framebuffer *fb, int crtc_x, int crtc_y,
unsigned int crtc_w, unsigned int crtc_h,
uint32_t src_x, uint32_t src_y,
uint32_t src_w, uint32_t src_h)
{
struct drm_device *dev = plane->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
struct intel_plane *intel_plane = to_intel_plane(plane);
struct intel_framebuffer *intel_fb;
struct drm_i915_gem_object *obj, *old_obj;
int pipe = intel_plane->pipe;
int ret = 0;
int x = src_x >> 16, y = src_y >> 16;
int primary_w = crtc->mode.hdisplay, primary_h = crtc->mode.vdisplay;
bool disable_primary = false;
intel_fb = to_intel_framebuffer(fb);
obj = intel_fb->obj;
old_obj = intel_plane->obj;
src_w = src_w >> 16;
src_h = src_h >> 16;
/* Pipe must be running... */
if (!(I915_READ(PIPECONF(pipe)) & PIPECONF_ENABLE))
return -EINVAL;
if (crtc_x >= primary_w || crtc_y >= primary_h)
return -EINVAL;
/* Don't modify another pipe's plane */
if (intel_plane->pipe != intel_crtc->pipe)
return -EINVAL;
/*
* Clamp the width & height into the visible area. Note we don't
* try to scale the source if part of the visible region is offscreen.
* The caller must handle that by adjusting source offset and size.
*/
if ((crtc_x < 0) && ((crtc_x + crtc_w) > 0)) {
crtc_w += crtc_x;
crtc_x = 0;
}
if ((crtc_x + crtc_w) <= 0) /* Nothing to display */
goto out;
if ((crtc_x + crtc_w) > primary_w)
crtc_w = primary_w - crtc_x;
if ((crtc_y < 0) && ((crtc_y + crtc_h) > 0)) {
crtc_h += crtc_y;
crtc_y = 0;
}
if ((crtc_y + crtc_h) <= 0) /* Nothing to display */
goto out;
if (crtc_y + crtc_h > primary_h)
crtc_h = primary_h - crtc_y;
if (!crtc_w || !crtc_h) /* Again, nothing to display */
goto out;
/*
* We can take a larger source and scale it down, but
* only so much... 16x is the max on SNB.
*/
if (((src_w * src_h) / (crtc_w * crtc_h)) > intel_plane->max_downscale)
return -EINVAL;
/*
* If the sprite is completely covering the primary plane,
* we can disable the primary and save power.
*/
if ((crtc_x == 0) && (crtc_y == 0) &&
(crtc_w == primary_w) && (crtc_h == primary_h))
disable_primary = true;
DRM_LOCK(dev);
ret = intel_pin_and_fence_fb_obj(dev, obj, NULL);
if (ret)
goto out_unlock;
intel_plane->obj = obj;
/*
* Be sure to re-enable the primary before the sprite is no longer
* covering it fully.
*/
if (!disable_primary && intel_plane->primary_disabled) {
intel_enable_primary(crtc);
intel_plane->primary_disabled = false;
}
intel_plane->update_plane(plane, fb, obj, crtc_x, crtc_y,
crtc_w, crtc_h, x, y, src_w, src_h);
if (disable_primary) {
intel_disable_primary(crtc);
intel_plane->primary_disabled = true;
}
/* Unpin old obj after new one is active to avoid ugliness */
if (old_obj) {
/*
* It's fairly common to simply update the position of
* an existing object. In that case, we don't need to
* wait for vblank to avoid ugliness, we only need to
* do the pin & ref bookkeeping.
*/
if (old_obj != obj) {
DRM_UNLOCK(dev);
intel_wait_for_vblank(dev, to_intel_crtc(crtc)->pipe);
DRM_LOCK(dev);
}
intel_unpin_fb_obj(old_obj);
}
out_unlock:
DRM_UNLOCK(dev);
out:
return ret;
}
static void intel_gma_init(const struct northbridge_intel_pineview_config *info,
struct device *vga, u8 *mmio, u8 *gtt, u32 physbase, u16 piobase)
{
int i;
u32 hactive, vactive;
u32 temp;
printk(BIOS_SPEW, "gtt %x mmio %x addrport %x physbase %x\n",
(u32)gtt, (u32)mmio, piobase, physbase);
gtt_setup(mmio);
pci_write_config16(vga, 0x52, 0x130);
/* Disable VGA. */
write32(mmio + VGACNTRL, VGA_DISP_DISABLE);
/* Disable pipes. */
write32(mmio + PIPECONF(0), 0);
write32(mmio + PIPECONF(1), 0);
write32(mmio + INSTPM, 0x800);
vga_gr_write(0x18, 0);
write32(mmio + VGA0, 0x200074);
write32(mmio + VGA1, 0x200074);
write32(mmio + DSPFW3, 0x7f3f00c1 & ~PINEVIEW_SELF_REFRESH_EN);
write32(mmio + DSPCLK_GATE_D, 0);
write32(mmio + FW_BLC, 0x03060106);
write32(mmio + FW_BLC2, 0x00000306);
write32(mmio + ADPA, ADPA_DAC_ENABLE
| ADPA_PIPE_A_SELECT
| ADPA_HOTPLUG_BITS
| ADPA_USE_VGA_HVPOLARITY
| ADPA_VSYNC_CNTL_ENABLE
| ADPA_HSYNC_CNTL_ENABLE
| ADPA_DPMS_ON
);
write32(mmio + 0x7041c, 0x0);
write32(mmio + DPLL_MD(0), 0x3);
write32(mmio + DPLL_MD(1), 0x3);
write32(mmio + DSPCNTR(1), 0x1000000);
write32(mmio + PIPESRC(1), 0x027f01df);
vga_misc_write(0x67);
const u8 cr[] = { 0x5f, 0x4f, 0x50, 0x82, 0x55, 0x81, 0xbf, 0x1f,
0x00, 0x4f, 0x0d, 0x0e, 0x00, 0x00, 0x00, 0x00,
0x9c, 0x8e, 0x8f, 0x28, 0x1f, 0x96, 0xb9, 0xa3,
0xff
};
vga_cr_write(0x11, 0);
for (i = 0; i <= 0x18; i++)
vga_cr_write(i, cr[i]);
// Disable screen memory to prevent garbage from appearing.
vga_sr_write(1, vga_sr_read(1) | 0x20);
hactive = 640;
vactive = 400;
mdelay(1);
write32(mmio + DPLL(0),
DPLL_VCO_ENABLE | DPLLB_MODE_DAC_SERIAL
| DPLL_VGA_MODE_DIS
| DPLL_DAC_SERIAL_P2_CLOCK_DIV_10
| 0x400601
);
mdelay(1);
write32(mmio + DPLL(0),
DPLL_VCO_ENABLE | DPLLB_MODE_DAC_SERIAL
| DPLL_VGA_MODE_DIS
| DPLL_DAC_SERIAL_P2_CLOCK_DIV_10
| 0x400601
);
write32(mmio + ADPA, ADPA_DAC_ENABLE
| ADPA_PIPE_A_SELECT
| ADPA_HOTPLUG_BITS
| ADPA_USE_VGA_HVPOLARITY
| ADPA_VSYNC_CNTL_ENABLE
| ADPA_HSYNC_CNTL_ENABLE
| ADPA_DPMS_ON
);
write32(mmio + HTOTAL(1), 0x031f027f);
write32(mmio + HBLANK(1), 0x03170287);
write32(mmio + HSYNC(1), 0x02ef028f);
write32(mmio + VTOTAL(1), 0x020c01df);
write32(mmio + VBLANK(1), 0x020401e7);
write32(mmio + VSYNC(1), 0x01eb01e9);
write32(mmio + HTOTAL(0),
((hactive - 1) << 16)
| (hactive - 1));
write32(mmio + HBLANK(0),
((hactive - 1) << 16)
| (hactive - 1));
write32(mmio + HSYNC(0),
((hactive - 1) << 16)
| (hactive - 1));
write32(mmio + VTOTAL(0), ((vactive - 1) << 16)
| (vactive - 1));
write32(mmio + VBLANK(0), ((vactive - 1) << 16)
| (vactive - 1));
write32(mmio + VSYNC(0),
((vactive - 1) << 16)
| (vactive - 1));
write32(mmio + PF_WIN_POS(0), 0);
write32(mmio + PIPESRC(0), (639 << 16) | 399);
write32(mmio + PF_CTL(0),PF_ENABLE | PF_FILTER_MED_3x3);
write32(mmio + PF_WIN_SZ(0), vactive | (hactive << 16));
write32(mmio + PFIT_CONTROL, 0x0);
mdelay(1);
write32(mmio + FDI_RX_CTL(0), 0x00002040);
mdelay(1);
write32(mmio + FDI_RX_CTL(0), 0x80002050);
write32(mmio + FDI_TX_CTL(0), 0x00044000);
mdelay(1);
write32(mmio + FDI_TX_CTL(0), 0x80044000);
write32(mmio + PIPECONF(0), PIPECONF_ENABLE | PIPECONF_BPP_6 | PIPECONF_DITHER_EN);
write32(mmio + VGACNTRL, 0x0);
write32(mmio + DSPCNTR(0), DISPLAY_PLANE_ENABLE | DISPPLANE_BGRX888);
mdelay(1);
write32(mmio + ADPA, ADPA_DAC_ENABLE
| ADPA_PIPE_A_SELECT
| ADPA_HOTPLUG_BITS
| ADPA_USE_VGA_HVPOLARITY
| ADPA_VSYNC_CNTL_ENABLE
| ADPA_HSYNC_CNTL_ENABLE
| ADPA_DPMS_ON
);
write32(mmio + DSPFW3, 0x7f3f00c1);
write32(mmio + MI_MODE, 0x200 | VS_TIMER_DISPATCH);
write32(mmio + CACHE_MODE_0, (0x6820 | (1 << 9)) & ~(1 << 5));
write32(mmio + CACHE_MODE_1, 0x380 & ~(1 << 9));
for (i = 0; i < (8192 - 512) / 4; i++) {
outl((i << 2) | 1, piobase);
outl(physbase + (i << 12) + 1, piobase + 4);
}
temp = read32(mmio + PGETBL_CTL);
printk(BIOS_INFO, "GTT PGETBL_CTL register : 0x%08x\n", temp);
temp = read32(mmio + PGETBL2_CTL);
printk(BIOS_INFO, "GTT PGETBL2_CTL register: 0x%08x\n", temp);
/* Clear interrupts. */
write32(mmio + DEIIR, 0xffffffff);
write32(mmio + SDEIIR, 0xffffffff);
write32(mmio + IIR, 0xffffffff);
write32(mmio + IMR, 0xffffffff);
write32(mmio + EIR, 0xffffffff);
vga_textmode_init();
/* Enable screen memory. */
vga_sr_write(1, vga_sr_read(1) & ~0x20);
}
