/*
* @ VS1003 write register
*/
void VS1003_write_reg(uint16 address, uint16 value){
VS_WAIT_DREQ();
SPI_enable(GPIOR_VS1003_CMDCH);
VSPI_WRITE(GPIOR_VS1003_CMDCH, address & 0x00ff | 0x0200);
VSPI_WRITE(GPIOR_VS1003_CMDCH, value);
SPI_disable(GPIOR_VS1003_CMDCH);
}
/*
* @ VS1003 write data
*/
void VS1003_write_data(char *buf, int len) {
VS_WAIT_DREQ();
SPI_enable(GPIOR_VS1003_DATCH);
while(len --) {
SPI_write(GPIOR_VS1003_DATCH, *(buf ++));
}
SPI_disable(GPIOR_VS1003_DATCH);
}
void MCP2515_reset(void)
{
SPI_enable();
SPI_transmit(MCP_RESET);
SPI_disable();
//Allow mcp2515 time to complete command
_delay_us(1);
}
char MCP2515_read_status(void)
{
SPI_enable();
SPI_transmit(MCP_READ_STATUS);
uint8_t status = SPI_receive();
SPI_disable();
return status;
}
void MCP2515_write(uint8_t data, uint8_t address)
{
SPI_enable();
SPI_transmit(MCP_WRITE);
SPI_transmit(address);
SPI_transmit(data);
SPI_disable();
}
uint8_t MCP2515_read(uint8_t address)
{
SPI_enable();
SPI_transmit(MCP_READ);
SPI_transmit(address);
uint8_t data = SPI_receive();
SPI_disable();
return data;
}
void MCP2515_bit_modify(uint8_t address, uint8_t mask, uint8_t data)
{
SPI_enable();
SPI_transmit(MCP_BITMOD);
SPI_transmit(address);
SPI_transmit(mask);
SPI_transmit(data);
SPI_disable();
}
/*
* @ VS1003 read register
*/
unsigned short VS1003_read_reg(uint16 address){
uint16 cache;
VS_WAIT_DREQ();
SPI_enable(GPIOR_VS1003_CMDCH);
VSPI_WRITE(GPIOR_VS1003_CMDCH, address & 0x00ff | 0x0300);
cache = VSPI_WRITE(GPIOR_VS1003_CMDCH, 0xffff);
SPI_disable(GPIOR_VS1003_CMDCH);
return cache;
}
// main function; program starts here
void main(void)
{
unsigned char data = 0;
unsigned int battery_voltage = 0; // ADC reading of battery voltage
ports_initialize(); // set up ports
ADC_initialize(); // configure ADC
SPI_initialize(); // set up SPI module
sleep_initialize(); // set up sleep mode
ISR_initialize(); // set up ISR
while(1)
{
SLEEP(); // sleep PIC until WDT expires
time++; // increment time (+16s)
battery_voltage = ADC_read(0x09); // read battery voltage
if ( time >= 1 ) // 1*16s=16s
{
time = 0; // reset time
if(battery_voltage >= 690) //690 = 11v
{
LATCbits.LATC4 = 1; // turn relay on
SPI_enable(); // turn on SPI module
while( data != 0xDA ) // wait for shutdown command to be received
{
while(!SSP1STATbits.BF) // wait till data is in the buffer
{
CLRWDT();
}
data = SSP1BUF; // read data outside
}
data = 0x00;
SPI_disable(); // turn off SPI module
__delay_ms(10000); // wait for R Pi to shutdown
LATCbits.LATC4 = 0; // turn relay off
}
}
}
}
void MCP2515_rts(uint8_t rts_port)
{
SPI_enable();
switch (rts_port){
case 0:
SPI_transmit(MCP_RTS_TX0);
break;
case 1:
SPI_transmit(MCP_RTS_TX1);
break;
case 2:
SPI_transmit(MCP_RTS_TX2);
break;
}
SPI_disable();
}
void main (void)
{
//Stop watchdog timer
WDT_hold(__MSP430_BASEADDRESS_WDT_A__);
//If clock signal from master stays low, it is not yet in SPI mode
while ( GPIO_INPUT_PIN_LOW ==
GPIO_getInputPinValue(__MSP430_BASEADDRESS_PORT3_R__,
GPIO_PORT_P3,
GPIO_PIN0
)) ;
//P3.5,4,0 option select
GPIO_setAsPeripheralModuleFunctionInputPin(__MSP430_BASEADDRESS_PORT3_R__,
GPIO_PORT_P3,
GPIO_PIN0 + GPIO_PIN4 + GPIO_PIN5
);
//Initialize slave to MSB first, inactive high clock polarity and 3 wire SPI
returnValue = SPI_slaveInit(__MSP430_BASEADDRESS_USCI_A0__,
SPI_MSB_FIRST,
SPI_PHASE_DATA_CAPTURED_ONFIRST_CHANGED_ON_NEXT,
SPI_CLOCKPOLARITY_INACTIVITY_HIGH
);
if (STATUS_FAIL == returnValue){
return;
}
//Enable SPI Module
SPI_enable(__MSP430_BASEADDRESS_USCI_A0__);
//Enable Receive interrupt
SPI_enableInterrupt(__MSP430_BASEADDRESS_USCI_A0__,
SPI_RECEIVE_INTERRUPT
);
//Enter LPM4, enable interrupts
__bis_SR_register(LPM4_bits + GIE);
}
void SPI_init(SPIDef * port, GPIOPin sck, GPIOPin miso, GPIOPin mosi, GPIOPin ncs) {
SPI_enable(port);
SPI_IOconfig(port, sck, miso, mosi, ncs);
SPI_start(port);
}
