void com_init(void) {
g_bUSBConfigured = false;
/* Enable the GPIO peripheral used for USB, and configure the USB pins. */
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
MAP_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_4 | GPIO_PIN_5);
/* Configure USB */
USBStackModeSet(0, eUSBModeForceDevice, 0);
USBDBulkInit(0, (tUSBDBulkDevice *)&g_sBulkDevice);
}
void
USB_Bulk_Init(void)
{
ReadSliderDIP();
if (g_Device.Serie == Axiolab)
*(uint16_t*)(&g_sBulkDevice.ui16PID) = 0x6000;
else if(g_Device.Serie == Axioscope)
*(uint16_t*)(&g_sBulkDevice.ui16PID) = 0x6001;
else
*(uint16_t*)(&g_sBulkDevice.ui16PID) = 0xbbbb;
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
USBDBulkInit(0, &g_sBulkDevice);
// Wait for initial configuration to complete.
//UARTprintf("Waiting for host...\n");
}
/************************************************************************************//**
** \brief Initializes the USB communication interface.
** \return none.
**
****************************************************************************************/
void UsbInit(void)
{
/* initialize the FIFO manager */
UsbFifoMgrInit();
/* place 2 buffers under FIFO management */
fifoPipeBulkIN.handle = UsbFifoMgrCreate(fifoPipeBulkIN.data, FIFO_PIPE_SIZE);
fifoPipeBulkOUT.handle = UsbFifoMgrCreate(fifoPipeBulkOUT.data, FIFO_PIPE_SIZE);
/* validate fifo handles */
ASSERT_RT( (fifoPipeBulkIN.handle != FIFO_ERR_INVALID_HANDLE) && \
(fifoPipeBulkOUT.handle != FIFO_ERR_INVALID_HANDLE) );
/* initialize the transmit and receive buffers */
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
/* pass our device information to the USB library and place the device on the bus */
instanceHandle = USBDBulkInit(0, &g_sBulkDevice);
ASSERT_RT(instanceHandle != BLT_NULL);
} /*** end of UsbInit ***/
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint_fast32_t ui32TxCount;
uint_fast32_t ui32RxCount;
tRectangle sRect;
char pcBuffer[16];
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
#ifdef DEBUG
//
// Configure the UART for debug output.
//
ConfigureUART();
#endif
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Initialize the display driver.
//
CFAL96x64x16Init();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sCFAL96x64x16);
//
// Fill the top part of the screen with blue to create the banner.
//
sRect.i16XMin = 0;
sRect.i16YMin = 0;
sRect.i16XMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.i16YMax = 9;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Change foreground for white text.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_psFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb-dev-bulk", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 4, 0);
//
// Show the various static text elements on the color STN display.
//
GrStringDraw(&g_sContext, "Tx bytes:", -1, 0, 32, false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, 0, 42, false);
//
// Enable the GPIO peripheral used for USB, and configure the USB
// pins.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Show the application name on the display and UART output.
//
DEBUG_PRINT("\nTiva C Series USB bulk device example\n");
DEBUG_PRINT("---------------------------------\n\n");
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, "Configuring USB");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, &g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, "Waiting for host");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ui32Flags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
g_ui32Flags &= ~COMMAND_STATUS_UPDATE;
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32TxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32TxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, " %d ", ui32TxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 48, 32, true);
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32RxCount)
{
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32RxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, " %d ", ui32RxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 48, 42, true);
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
unsigned long ulTxCount;
unsigned long ulRxCount;
tRectangle sRect;
char pcBuffer[16];
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_8MHZ);
#ifdef DEBUG
//
// Configure the relevant pins such that UART0 owns them.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Open UART0 for debug output.
//
UARTStdioInit(0);
#endif
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Initialize the display driver.
//
Formike128x128x16Init();
//
// Turn on the backlight.
//
Formike128x128x16BacklightOn();
//
// Initialize the graphics context.
//
GrContextInit(&g_sContext, &g_sFormike128x128x16);
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = 14;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_pFontFixed6x8);
GrStringDrawCentered(&g_sContext, "usb_dev_bulk", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 7, 0);
//
// Show the various static text elements on the color STN display.
//
GrContextFontSet(&g_sContext, TEXT_FONT);
GrStringDraw(&g_sContext, "Tx bytes:", -1, 8, 70, false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, 8, 90, false);
//
// Configure the USB mux on the board to put us in device mode. We pull
// the relevant pin high to do this.
//
ROM_SysCtlPeripheralEnable(USB_MUX_GPIO_PERIPH);
ROM_GPIOPinTypeGPIOOutput(USB_MUX_GPIO_BASE, USB_MUX_GPIO_PIN);
ROM_GPIOPinWrite(USB_MUX_GPIO_BASE, USB_MUX_GPIO_PIN, USB_MUX_SEL_DEVICE);
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Show the application name on the display and UART output.
//
DEBUG_PRINT("\nStellaris USB bulk device example\n");
DEBUG_PRINT("---------------------------------\n\n");
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, "Configuring USB...");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit((tUSBBuffer *)&g_sTxBuffer);
USBBufferInit((tUSBBuffer *)&g_sRxBuffer);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, (tUSBDBulkDevice *)&g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, "Waiting for host...");
//
// Clear our local byte counters.
//
ulRxCount = 0;
ulTxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ulFlags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
g_ulFlags &= ~COMMAND_STATUS_UPDATE;
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ulTxCount != g_ulTxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ulTxCount = g_ulTxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, "%d", ulTxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 70, 70, true);
}
//
// Has there been any receive traffic since we last checked?
//
if(ulRxCount != g_ulRxCount)
{
//
// Take a snapshot of the latest receive count.
//
ulRxCount = g_ulRxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, "%d", ulRxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 70, 90, true);
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
unsigned long ulTxCount;
unsigned long ulRxCount;
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the UART.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTStdioInit(0);
UARTprintf("\033[2JBulk device application\n");
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, USB_MODE_DEVICE, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, &g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
UARTprintf("Waiting for host...\n");
//
// Clear our local byte counters.
//
ulRxCount = 0;
ulTxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// See if any data has been transferred.
//
if((ulTxCount != g_ulTxCount) || (ulRxCount != g_ulRxCount))
{
//
// Take a snapshot of the latest transmit and receive counts.
//
ulTxCount = g_ulTxCount;
ulRxCount = g_ulRxCount;
//
// Update the display of bytes transferred.
//
UARTprintf("\rTx: %d Rx: %d", ulTxCount, ulRxCount);
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
volatile uint32_t ui32Loop;
uint32_t ui32TxCount;
uint32_t ui32RxCount;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2 & PF3).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3 | GPIO_PIN_2);
//
// Open UART0 and show the application name on the UART.
//
ConfigureUART();
UARTprintf("\033[2JTiva C Series USB bulk device example\n");
UARTprintf("---------------------------------\n\n");
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the GPIO peripheral used for USB, and configure the USB
// pins.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_4 | GPIO_PIN_5);
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Tell the user what we are up to.
//
UARTprintf("Configuring USB\n");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeForceDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, &g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
UARTprintf("Waiting for host...\n");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// See if any data has been transferred.
//
if((ui32TxCount != g_ui32TxCount) || (ui32RxCount != g_ui32RxCount))
{
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32TxCount)
{
//
// Turn on the Green LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, GPIO_PIN_3);
//
// Delay for a bit.
//
for(ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Green LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, 0);
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32TxCount;
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32RxCount)
{
//
// Turn on the Blue LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, GPIO_PIN_2);
//
// Delay for a bit.
//
for(ui32Loop = 0; ui32Loop < 150000; ui32Loop++)
{
}
//
// Turn off the Blue LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, 0);
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32RxCount;
}
//
// Update the display of bytes transferred.
//
UARTprintf("\rTx: %d Rx: %d", ui32TxCount, ui32RxCount);
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
unsigned int ulTxCount;
unsigned int ulRxCount;
tRectangle sRect;
char pcBuffer[16];
unsigned int i;
unsigned char *src, *dest;
MMUConfigAndEnable();
//
// USB module clock enable
//
USB0ModuleClkConfig();
//
//USB interrupt enable
//
USBInterruptEnable();
//
//LCD back light enable
//
LCDBackLightEnable();
// UPD Pin setup
//
//
UPDNPinControl();
//
//Delay timer setup
//
DelayTimerSetup();
//
//Configures raster to display image
//
SetUpLCD();
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_0);
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_1);
src = (unsigned char *) palette_32b;
dest = (unsigned char *) (g_pucBuffer+PALETTE_OFFSET);
// Copy palette info into buffer
for( i = PALETTE_OFFSET; i < (PALETTE_SIZE+PALETTE_OFFSET); i++)
{
*dest++ = *src++;
}
GrOffScreen24BPPInit(&g_s35_800x480x24Display, g_pucBuffer, LCD_WIDTH, LCD_HEIGHT);
// Initialize a drawing context.
GrContextInit(&g_sContext, &g_s35_800x480x24Display);
/* enable End of frame interrupt */
RasterEndOfFrameIntEnable(SOC_LCDC_0_REGS);
/* enable raster */
RasterEnable(SOC_LCDC_0_REGS);
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = 23;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, &g_sFontCm20);
GrStringDrawCentered(&g_sContext, "usb-dev-bulk", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 10, 0);
//
// Show the various static text elements on the color STN display.
//
GrContextFontSet(&g_sContext, TEXT_FONT);
GrStringDraw(&g_sContext, "Tx bytes:", -1, 8, 100, false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, 8, 130, false);
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, " Configuring USB... ");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit((tUSBBuffer *)&g_sTxBuffer);
USBBufferInit((tUSBBuffer *)&g_sRxBuffer);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, (tUSBDBulkDevice *)&g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, "Waiting for host...");
//
// Clear our local byte counters.
//
ulRxCount = 0;
ulTxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ulFlags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
g_ulFlags &= ~COMMAND_STATUS_UPDATE;
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ulTxCount != g_ulTxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ulTxCount = g_ulTxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, " %d ", ulTxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 120, 100, true);
}
//
// Has there been any receive traffic since we last checked?
//
if(ulRxCount != g_ulRxCount)
{
//
// Take a snapshot of the latest receive count.
//
ulRxCount = g_ulRxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, " %d ", ulRxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 120, 130, true);
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50MHz
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2 & PF3).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3 | GPIO_PIN_2 | GPIO_PIN_1);
//
// Open UART0 and show the application name on the UART.
//
ConfigureUART();
UARTprintf("\033[2JTiva C Series USB bulk device example\n");
UARTprintf("---------------------------------\n\n");
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the GPIO peripheral used for USB, and configure the USB
// pins.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_4 | GPIO_PIN_5);
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Tell the user what we are up to.
//
UARTprintf("Configuring USB\n");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, eUSBModeForceDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
myBulk=USBDBulkInit(0, &g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
UARTprintf("Waiting for host...\n");
//
// Clear our local byte counters.
//
while(!isUSB_ready);
adc_cofig();
//
// Main application loop.
//
while(1)
{
int readVal;
if(txReady){
adc_capture();
((int*)myOutBuffer)[0]=adc_getData();
readVal=((int*)myOutBuffer)[0];
UARTprintf("adc = %d\n",readVal);
txReady=0;
USBDBulkPacketWrite(myBulk,myOutBuffer,4,true);
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
uint_fast32_t ui32TxCount;
uint_fast32_t ui32RxCount;
uint32_t ui32SysClock;
//
// Run from the PLL at 120 MHz.
//
ui32SysClock = MAP_SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ |
SYSCTL_OSC_MAIN |
SYSCTL_USE_PLL |
SYSCTL_CFG_VCO_480), 120000000);
//
// Configure the device pins.
//
PinoutSet(false, true);
//
// Enable UART0
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
//
// Initialize the UART for console I/O.
//
UARTStdioConfig(0, 115200, ui32SysClock);
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
// Enable the system tick.
//
ROM_SysTickPeriodSet(ui32SysClock / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Show the application name on the display and UART output.
//
UARTprintf("\033[2J\nTiva C Series USB bulk device example\n");
UARTprintf("---------------------------------\n\n");
//
// Tell the user what we are up to.
//
UARTprintf("Configuring USB... \n");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit(&g_sTxBuffer);
USBBufferInit(&g_sRxBuffer);
//
// Initialize the USB stack for device mode.
//
USBStackModeSet(0, eUSBModeDevice, 0);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, &g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
UARTprintf("Waiting for host...\r");
//
// Clear our local byte counters.
//
ui32RxCount = 0;
ui32TxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ui32Flags & COMMAND_STATUS_UPDATE)
{
g_ui32Flags &= ~COMMAND_STATUS_UPDATE;
if(g_bUSBConfigured)
{
UARTprintf("Host Connected. \n\n");
UARTprintf("Data transferred:\n");
UARTprintf("TX: %d RX: %d \r",
g_ui32TxCount,
g_ui32RxCount);
}
else
{
UARTprintf("\n\nHost Disconnected.\n\n");
}
}
//
// Has there been any transmit traffic since we last checked?
//
if(ui32TxCount != g_ui32TxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ui32TxCount = g_ui32TxCount;
//
// Update the displayed buffer count information.
//
UARTprintf("TX: %d RX: %d \r",
g_ui32TxCount,
g_ui32RxCount);
}
//
// Has there been any receive traffic since we last checked?
//
if(ui32RxCount != g_ui32RxCount)
{
//
// Take a snapshot of the latest receive count.
//
ui32RxCount = g_ui32RxCount;
//
// Update the displayed buffer count information.
//
UARTprintf("TX: %d RX: %d \r",
g_ui32TxCount,
g_ui32RxCount);
}
}
}
