static int
xspi_release(struct inode *inode, struct file *filp)
{
struct xspi_instance *dev = filp->private_data;
func_enter();
if (down_interruptible(&dev->sem))
return -EINTR;
if (--dev->use_count == 0) {
/* This was the last closer: stop the device and free the IRQ */
if (wait_event_interruptible(dev->waitq,
XSpi_Stop(&dev->Spi) !=
XST_DEVICE_BUSY) != 0) {
/* Abort transfer by brute force */
XSpi_Abort(&dev->Spi);
}
disable_irq(dev->irq);
free_irq(dev->irq, &dev->Spi);
}
up(&dev->sem);
return 0;
}
/*
* This function is called back from the XSpi interrupt handler
* when one of the following status events occures:
* XST_SPI_TRANSFER_DONE - the requested data transfer is done,
* XST_SPI_RECEIVE_OVERRUN - Rx FIFO overrun, transmission continues,
* XST_SPI_MODE_FAULT - should not happen: the driver doesn't support multiple masters,
* XST_SPI_TRANSMIT_UNDERRUN,
* XST_SPI_SLAVE_MODE_FAULT - should not happen: the driver doesn't support slave mode.
*/
static void xspi_status_handler(void *CallBackRef, u32 StatusEvent,
unsigned int ByteCount)
{
struct xspi_instance *dev = (struct xspi_instance *) CallBackRef;
dev->completion_status = StatusEvent;
if (StatusEvent == XST_SPI_TRANSFER_DONE) {
dev->tx_count = (int) ByteCount;
wake_up_interruptible(&dev->waitq);
} else if (StatusEvent == XST_SPI_RECEIVE_OVERRUN) {
/* As both Rx and Tx FIFO have the same sizes
this should not happen in master mode.
That is why we consider Rx overrun as severe error
and abort the transfer */
dev->tx_count = (int) ByteCount;
XSpi_Abort(&dev->Spi);
wake_up_interruptible(&dev->waitq);
printk(KERN_ERR XSPI_NAME " %d: Rx overrun!!!.\n",
dev->device_id);
} else if (StatusEvent == XST_SPI_MODE_FAULT) {
wake_up_interruptible(&dev->waitq);
} else {
printk(KERN_ERR XSPI_NAME " %d: Invalid status event %u.\n",
dev->device_id, StatusEvent);
}
}
/**
*
* Resets the SPI device by writing to the Software Reset register. Reset must
* only be called after the driver has been initialized. The configuration of the
* device after reset is the same as its configuration after initialization.
* Refer to the XSpi_Initialize function for more details. This is a hard reset
* of the device. Any data transfer that is in progress is aborted.
*
* The upper layer software is responsible for re-configuring (if necessary)
* and restarting the SPI device after the reset.
*
* @param InstancePtr is a pointer to the XSpi instance to be worked on.
*
* @return None.
*
* @note None.
*
******************************************************************************/
void XSpi_Reset(XSpi *InstancePtr)
{
Xil_AssertVoid(InstancePtr != NULL);
Xil_AssertVoid(InstancePtr->IsReady == XIL_COMPONENT_IS_READY);
/*
* Abort any transfer that is in progress.
*/
XSpi_Abort(InstancePtr);
/*
* Reset any values that are not reset by the hardware reset such that
* the software state matches the hardware device.
*/
InstancePtr->IsStarted = 0;
InstancePtr->SlaveSelectReg = InstancePtr->SlaveSelectMask;
/*
* Reset the device.
*/
XSpi_WriteReg(InstancePtr->BaseAddr, XSP_SRR_OFFSET,
XSP_SRR_RESET_MASK);
}
