//******************************************************************************
// board_uart_enable_clock
//
// Ensures that the specified UART's clock is turned on.
//******************************************************************************
int board_uart_enable_clock (int module_id)
{
//--------------------------------------------------------
// Turn on clock for the associated SPIx module.
//--------------------------------------------------------
switch (module_id)
{ case 0: // USARTMD / VCP
__USART2_CLK_ENABLE();
break;
case 1: // USART1
__USART1_CLK_ENABLE();
break;
case 2: // USART2
__USART2_CLK_ENABLE();
break;
#if defined(STM32F446xx)
case 3: // USART3
__USART3_CLK_ENABLE();
break;
case 4: // UART4
__UART4_CLK_ENABLE();
break;
case 5: // UART5
__UART5_CLK_ENABLE();
break;
#endif
case 6: // USART6
__USART6_CLK_ENABLE();
break;
}
return (0); // denote everything worked OK
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART1)
{
/* USER CODE BEGIN USART1_MspInit 0 */
/* USER CODE END USART1_MspInit 0 */
/* Peripheral clock enable */
__USART1_CLK_ENABLE();
/**USART1 GPIO Configuration
PA9 ------> USART1_TX
PA10 ------> USART1_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART1_MspInit 1 */
/* USER CODE END USART1_MspInit 1 */
}
else if (huart->Instance == USART2)
{
__USART2_CLK_ENABLE();
GPIO_InitStruct.Pin = GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_2;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
}
else if (huart->Instance == USART3)
{
__USART3_CLK_ENABLE();
GPIO_InitStruct.Pin = GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
}
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART2)
{
/* USER CODE BEGIN USART2_MspInit 0 */
/* USER CODE END USART2_MspInit 0 */
/* Peripheral clock enable */
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
GPIO_InitStruct.Pin = USART_TX_Pin|USART_RX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART2_MspInit 1 */
/* USER CODE END USART2_MspInit 1 */
}
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART2)
{
/* USER CODE BEGIN USART2_MspInit 0 */
/* USER CODE END USART2_MspInit 0 */
/* Peripheral clock enable */
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
GPIO_InitStruct.Pin = USART_TX_Pin|USART_RX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(USART2_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART2_IRQn);
/* USER CODE BEGIN USART2_MspInit 1 */
/* USER CODE END USART2_MspInit 1 */
}
}
void serial_init(serial_t *obj, PinName tx, PinName rx)
{
// Determine the UART to use (UART_1, UART_2, ...)
UARTName uart_tx = (UARTName)pinmap_peripheral(tx, PinMap_UART_TX);
UARTName uart_rx = (UARTName)pinmap_peripheral(rx, PinMap_UART_RX);
// Get the peripheral name (UART_1, UART_2, ...) from the pin and assign it to the object
obj->uart = (UARTName)pinmap_merge(uart_tx, uart_rx);
MBED_ASSERT(obj->uart != (UARTName)NC);
// Enable UART clock
if (obj->uart == UART_1) {
__USART1_CLK_ENABLE();
obj->index = 0;
}
if (obj->uart == UART_2) {
__USART2_CLK_ENABLE();
obj->index = 1;
}
if (obj->uart == UART_3) {
__USART3_CLK_ENABLE();
obj->index = 2;
}
// Configure the UART pins
pinmap_pinout(tx, PinMap_UART_TX);
pinmap_pinout(rx, PinMap_UART_RX);
if (tx != NC) {
pin_mode(tx, PullUp);
}
if (rx != NC) {
pin_mode(rx, PullUp);
}
// Configure UART
#if defined (MX_DEFAULT_SERIAL_BAUD)
obj->baudrate = MX_DEFAULT_SERIAL_BAUD;
#else
obj->baudrate = 9600;
#endif
obj->databits = UART_WORDLENGTH_8B;
obj->stopbits = UART_STOPBITS_1;
obj->parity = UART_PARITY_NONE;
obj->pin_tx = tx;
obj->pin_rx = rx;
init_uart(obj);
// For stdio management
if (obj->uart == STDIO_UART) {
stdio_uart_inited = 1;
memcpy(&stdio_uart, obj, sizeof(serial_t));
}
}
void serial_init(serial_t *obj, PinName tx, PinName rx) {
// Determine the UART to use (UART_1, UART_2, ...)
UARTName uart_tx = (UARTName)pinmap_peripheral(tx, PinMap_UART_TX);
UARTName uart_rx = (UARTName)pinmap_peripheral(rx, PinMap_UART_RX);
// Get the peripheral name (UART_1, UART_2, ...) from the pin and assign it to the object
obj->uart = (UARTName)pinmap_merge(uart_tx, uart_rx);
if (obj->uart == (UARTName)NC) {
error("Serial error: pinout mapping failed.");
}
// Enable USART clock
if (obj->uart == UART_1) {
__USART1_CLK_ENABLE();
obj->index = 0;
}
if (obj->uart == UART_2) {
__USART2_CLK_ENABLE();
obj->index = 1;
}
if (obj->uart == UART_3) {
__USART3_CLK_ENABLE();
obj->index = 2;
}
if (obj->uart == UART_4) {
__USART4_CLK_ENABLE();
obj->index = 3;
}
// Configure the UART pins
pinmap_pinout(tx, PinMap_UART_TX);
pinmap_pinout(rx, PinMap_UART_RX);
pin_mode(tx, PullUp);
pin_mode(rx, PullUp);
// Configure UART
obj->baudrate = 9600;
obj->databits = UART_WORDLENGTH_8B;
obj->stopbits = UART_STOPBITS_1;
obj->parity = UART_PARITY_NONE;
obj->pin_tx = tx;
obj->pin_rx = rx;
init_uart(obj);
// For stdio management
if (obj->uart == STDIO_UART) {
stdio_uart_inited = 1;
memcpy(&stdio_uart, obj, sizeof(serial_t));
}
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART1)
{
/* USER CODE BEGIN USART1_MspInit 0 */
/* USER CODE END USART1_MspInit 0 */
/* Peripheral clock enable */
__USART1_CLK_ENABLE();
/**USART1 GPIO Configuration
PA9 ------> USART1_TX
PA10 ------> USART1_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART1_MspInit 1 */
/* USER CODE END USART1_MspInit 1 */
}
else if(huart->Instance==USART2)
{
/* USER CODE BEGIN USART2_MspInit 0 */
/* USER CODE END USART2_MspInit 0 */
/* Peripheral clock enable */
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART2_MspInit 1 */
/* USER CODE END USART2_MspInit 1 */
}
}
void Uart2UARTInit(UART_HandleTypeDef* huart) {
__USART2_CLK_ENABLE()
;
huart->Instance = USART2;
huart->Init.BaudRate = 115200;
huart->Init.WordLength = UART_WORDLENGTH_8B;
huart->Init.StopBits = UART_STOPBITS_1;
huart->Init.Parity = UART_PARITY_NONE;
huart->Init.Mode = UART_MODE_TX_RX;
huart->Init.HwFlowCtl = UART_HWCONTROL_NONE;
huart->Init.OverSampling = UART_OVERSAMPLING_16;
MyHAL_UARTInit(huart);
__HAL_UART_ENABLE_IT(huart, UART_IT_RXNE);
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART2)
{
/* USER CODE BEGIN USART2_MspInit 0 */
/* USER CODE END USART2_MspInit 0 */
/* Peripheral clock enable */
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_2;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* Peripheral DMA init*/
hdma_usart2_rx.Instance = DMA1_Channel6;
hdma_usart2_rx.Init.Direction = DMA_PERIPH_TO_MEMORY;
hdma_usart2_rx.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_usart2_rx.Init.MemInc = DMA_MINC_ENABLE;
hdma_usart2_rx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
hdma_usart2_rx.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
hdma_usart2_rx.Init.Mode = DMA_CIRCULAR;
hdma_usart2_rx.Init.Priority = DMA_PRIORITY_LOW;
HAL_DMA_Init(&hdma_usart2_rx);
__HAL_LINKDMA(huart,hdmarx,hdma_usart2_rx);
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(USART2_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART2_IRQn);
/* USER CODE BEGIN USART2_MspInit 1 */
/* USER CODE END USART2_MspInit 1 */
}
}
void HAL_UART_MspInit(UART_HandleTypeDef* UART2)
{
if(UART2->Instance==USART2)
{
/* Peripheral clock enable */
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
* PA2 ------> USART2_TX
* PA3 ------> USART2_RX
* */
GPIO_InitStructure.Pin = GPIO_PIN_2 | GPIO_PIN_3;
GPIO_InitStructure.Mode = GPIO_MODE_AF_PP;
GPIO_InitStructure.Pull = GPIO_NOPULL;
GPIO_InitStructure.Speed = GPIO_SPEED_LOW;
GPIO_InitStructure.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStructure);
}
}
void HAL_USART_MspInit(USART_HandleTypeDef *huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
/* Enable GPIO TX/RX and USART clock */
__GPIOA_CLK_ENABLE();
__USART2_CLK_ENABLE();
/* USART TX/RX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_2 | GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* NVIC for USART */
HAL_NVIC_SetPriority(USART2_IRQn, 0, 1);
HAL_NVIC_EnableIRQ(USART2_IRQn);
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART2)
{
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PD5 ------> USART2_TX
PD6 ------> USART2_RX
*/
GPIO_InitStruct.Pin = USART_TX_Pin|USART_RX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
}
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART1)
{
__USART1_CLK_ENABLE();
/**USART1 GPIO Configuration
PA9 ------> USART1_TX
PA10 ------> USART1_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
}
else if(huart->Instance==USART2)
{
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
}
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==UART4)
{
/* USER CODE BEGIN UART4_MspInit 0 */
/* USER CODE END UART4_MspInit 0 */
/* Peripheral clock enable */
__UART4_CLK_ENABLE();
/**UART4 GPIO Configuration
PC10 ------> UART4_TX
PC11 ------> UART4_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF5_UART4;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/* USER CODE BEGIN UART4_MspInit 1 */
/* USER CODE END UART4_MspInit 1 */
}
else if(huart->Instance==UART5)
{
/* USER CODE BEGIN UART5_MspInit 0 */
/* USER CODE END UART5_MspInit 0 */
/* Peripheral clock enable */
__UART5_CLK_ENABLE();
/**UART5 GPIO Configuration
PC12 ------> UART5_TX
PD2 ------> UART5_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_12;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF5_UART5;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_2;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF5_UART5;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
/* USER CODE BEGIN UART5_MspInit 1 */
/* USER CODE END UART5_MspInit 1 */
}
else if(huart->Instance==USART2)
{
/* USER CODE BEGIN USART2_MspInit 0 */
/* USER CODE END USART2_MspInit 0 */
/* Peripheral clock enable */
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART2_MspInit 1 */
/* USER CODE END USART2_MspInit 1 */
}
else if(huart->Instance==USART3)
{
/* USER CODE BEGIN USART3_MspInit 0 */
/* USER CODE END USART3_MspInit 0 */
/* Peripheral clock enable */
__USART3_CLK_ENABLE();
/**USART3 GPIO Configuration
PE15 ------> USART3_RX
PB10 ------> USART3_TX
*/
GPIO_InitStruct.Pin = GPIO_PIN_15;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
HAL_GPIO_Init(GPIOE, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/* USER CODE BEGIN USART3_MspInit 1 */
/* USER CODE END USART3_MspInit 1 */
}
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART1)
{
/* Peripheral clock enable */
__USART1_CLK_ENABLE();
__GPIOA_CLK_ENABLE();
/**USART1 GPIO Configuration
PA9 ------> USART1_TX
PA10 ------> USART1_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* Peripheral interrupt init*/
// /* Sets the priority grouping field */
HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_0);
HAL_NVIC_SetPriority(USART1_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART1_IRQn);
}
else if(huart->Instance==USART2)
{
/* Peripheral clock enable */
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
}
else if(huart->Instance==USART3)
{
/* Peripheral clock enable */
__USART3_CLK_ENABLE();
/**USART3 GPIO Configuration
PB10 ------> USART3_TX
PB11 ------> USART3_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
}
else if(huart->Instance==USART6)
{
/* Peripheral clock enable */
__USART6_CLK_ENABLE();
__GPIOC_CLK_ENABLE();
/**USART6 GPIO Configuration
PC6 ------> USART6_TX
PC7 ------> USART6_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_6|GPIO_PIN_7;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF8_USART6;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/* Peripheral interrupt init*/
// /* Sets the priority grouping field */
// HAL_NVIC_SetPriorityGrouping(NVIC_PRIORITYGROUP_0);
// HAL_NVIC_SetPriority(USART6_IRQn, 0, 0);
// HAL_NVIC_EnableIRQ(USART6_IRQn);
}
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART1)
{
/* USER CODE BEGIN USART1_MspInit 0 */
/* USER CODE END USART1_MspInit 0 */
/* Peripheral clock enable */
__USART1_CLK_ENABLE();
/**USART1 GPIO Configuration
PA9 ------> USART1_TX
PA10 ------> USART1_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(USART1_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(USART1_IRQn);
/* USER CODE BEGIN USART1_MspInit 1 */
/* USER CODE END USART1_MspInit 1 */
}
else if(huart->Instance==USART2)
{
/* USER CODE BEGIN USART2_MspInit 0 */
/* USER CODE END USART2_MspInit 0 */
/* Peripheral clock enable */
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* Peripheral DMA init*/
hdma_usart2_tx.Instance = DMA1_Stream6;
hdma_usart2_tx.Init.Channel = DMA_CHANNEL_4;
hdma_usart2_tx.Init.Direction = DMA_MEMORY_TO_PERIPH;
hdma_usart2_tx.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_usart2_tx.Init.MemInc = DMA_MINC_ENABLE;
hdma_usart2_tx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
hdma_usart2_tx.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
hdma_usart2_tx.Init.Mode = DMA_NORMAL;
hdma_usart2_tx.Init.Priority = DMA_PRIORITY_LOW;
hdma_usart2_tx.Init.FIFOMode = DMA_FIFOMODE_ENABLE;
hdma_usart2_tx.Init.FIFOThreshold = DMA_FIFO_THRESHOLD_HALFFULL;
hdma_usart2_tx.Init.MemBurst = DMA_MBURST_SINGLE;
hdma_usart2_tx.Init.PeriphBurst = DMA_PBURST_SINGLE;
HAL_DMA_Init(&hdma_usart2_tx);
__HAL_LINKDMA(huart,hdmatx,hdma_usart2_tx);
hdma_usart2_rx.Instance = DMA1_Stream5;
hdma_usart2_rx.Init.Channel = DMA_CHANNEL_4;
hdma_usart2_rx.Init.Direction = DMA_PERIPH_TO_MEMORY;
hdma_usart2_rx.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_usart2_rx.Init.MemInc = DMA_MINC_ENABLE;
hdma_usart2_rx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
hdma_usart2_rx.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
hdma_usart2_rx.Init.Mode = DMA_NORMAL;
hdma_usart2_rx.Init.Priority = DMA_PRIORITY_LOW;
hdma_usart2_rx.Init.FIFOMode = DMA_FIFOMODE_ENABLE;
hdma_usart2_rx.Init.FIFOThreshold = DMA_FIFO_THRESHOLD_HALFFULL;
hdma_usart2_rx.Init.MemBurst = DMA_MBURST_SINGLE;
hdma_usart2_rx.Init.PeriphBurst = DMA_PBURST_SINGLE;
HAL_DMA_Init(&hdma_usart2_rx);
__HAL_LINKDMA(huart,hdmarx,hdma_usart2_rx);
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(USART2_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(USART2_IRQn);
/* USER CODE BEGIN USART2_MspInit 1 */
/* USER CODE END USART2_MspInit 1 */
}
}
/**
* @brief UART MSP Initialization
* This function configures the hardware resources used in this example:
* - Peripheral's clock enable
* - Peripheral's GPIO Configuration
* - NVIC configuration for UART interrupt request enable
* @param huart: UART handle pointer
* @retval None
*/
void HAL_UART_MspInit(UART_HandleTypeDef *huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
switch((uint32_t)huart->Instance)
{
case (uint32_t)USART1 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOA_CLK_ENABLE();
/* Enable USARTx clock */
__USART1_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_9 | GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART1_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(USART1_IRQn);
}
break;
case (uint32_t)USART2 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOD_CLK_ENABLE();
/* Enable USARTx clock */
__USART2_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_6 | GPIO_PIN_5;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF0_USART2;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART2_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(USART2_IRQn);
}
break;
case (uint32_t)USART3 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOD_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART3_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_8 | GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF0_USART3;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
case (uint32_t)USART4 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOC_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART4_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_10 | GPIO_PIN_11;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF0_USART4;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
case (uint32_t)USART5 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOB_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART5_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_3 | GPIO_PIN_4;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF4_USART5;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
case (uint32_t)USART6 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOF_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART6_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_9 | GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART6;
HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
case (uint32_t)USART7 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOF_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART7_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_3 | GPIO_PIN_2;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART7;
HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
case (uint32_t)USART8 :
{
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
__GPIOC_CLK_ENABLE();
/* To allow the IT source identification */
__SYSCFG_CLK_ENABLE();
/* Enable USARTx clock */
__USART8_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = GPIO_PIN_8 | GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF1_USART8;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/*##-3- Configure the NVIC for UART ########################################*/
/* NVIC for USART */
HAL_NVIC_SetPriority(USART3_8_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(USART3_8_IRQn);
}
break;
}
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART1)
{
/* USER CODE BEGIN USART1_MspInit 0 */
/* USER CODE END USART1_MspInit 0 */
/* Peripheral clock enable */
__USART1_CLK_ENABLE();
/**USART1 GPIO Configuration
PA10 ------> USART1_RX
PA9 ------> USART1_TX
*/
GPIO_InitStruct.Pin = U1RX_Pin|U1TX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART1_MspInit 1 */
/* USER CODE END USART1_MspInit 1 */
}
else if(huart->Instance==USART2)
{
/* USER CODE BEGIN USART2_MspInit 0 */
/* USER CODE END USART2_MspInit 0 */
/* Peripheral clock enable */
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PA1 ------> USART2_RTS
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
GPIO_InitStruct.Pin = RS_ON232_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(RS_ON232_GPIO_Port, &GPIO_InitStruct);
GPIO_InitStruct.Pin = RS_TX_Pin|RS_RX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART2_MspInit 1 */
/* USER CODE END USART2_MspInit 1 */
}
else if(huart->Instance==USART3)
{
/* USER CODE BEGIN USART3_MspInit 0 */
/* USER CODE END USART3_MspInit 0 */
/* Peripheral clock enable */
__USART3_CLK_ENABLE();
/**USART3 GPIO Configuration
PC11 ------> USART3_RX
PC10 ------> USART3_TX
*/
GPIO_InitStruct.Pin = RS485_RX_Pin|RS485_TX_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/* USER CODE BEGIN USART3_MspInit 1 */
/* USER CODE END USART3_MspInit 1 */
}
}
// assumes Init parameters have been set up correctly
STATIC bool uart_init2(pyb_uart_obj_t *uart_obj) {
USART_TypeDef *UARTx;
IRQn_Type irqn;
uint32_t GPIO_Pin, GPIO_Pin2 = 0;
uint8_t GPIO_AF_UARTx = 0;
GPIO_TypeDef* GPIO_Port = NULL;
GPIO_TypeDef* GPIO_Port2 = NULL;
switch (uart_obj->uart_id) {
#if defined(MICROPY_HW_UART1_PORT) && defined(MICROPY_HW_UART1_PINS)
// USART1 is on PA9/PA10 (CK on PA8), PB6/PB7
case PYB_UART_1:
UARTx = USART1;
irqn = USART1_IRQn;
GPIO_AF_UARTx = GPIO_AF7_USART1;
GPIO_Port = MICROPY_HW_UART1_PORT;
GPIO_Pin = MICROPY_HW_UART1_PINS;
__USART1_CLK_ENABLE();
break;
#endif
#if defined(MICROPY_HW_UART1_TX_PORT) && \
defined(MICROPY_HW_UART1_TX_PIN) && \
defined(MICROPY_HW_UART1_RX_PORT) && \
defined(MICROPY_HW_UART1_RX_PIN)
case PYB_UART_1:
UARTx = USART1;
irqn = USART1_IRQn;
GPIO_AF_UARTx = GPIO_AF7_USART1;
GPIO_Port = MICROPY_HW_UART1_TX_PORT;
GPIO_Pin = MICROPY_HW_UART1_TX_PIN;
GPIO_Port2 = MICROPY_HW_UART1_RX_PORT;
GPIO_Pin2 = MICROPY_HW_UART1_RX_PIN;
__USART1_CLK_ENABLE();
break;
#endif
#if defined(MICROPY_HW_UART2_PORT) && defined(MICROPY_HW_UART2_PINS)
// USART2 is on PA2/PA3 (CTS,RTS,CK on PA0,PA1,PA4), PD5/PD6 (CK on PD7)
case PYB_UART_2:
UARTx = USART2;
irqn = USART2_IRQn;
GPIO_AF_UARTx = GPIO_AF7_USART2;
GPIO_Port = MICROPY_HW_UART2_PORT;
GPIO_Pin = MICROPY_HW_UART2_PINS;
#if defined(MICROPY_HW_UART2_RTS)
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_RTS) {
GPIO_Pin |= MICROPY_HW_UART2_RTS;
}
#endif
#if defined(MICROPY_HW_UART2_CTS)
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_CTS) {
GPIO_Pin |= MICROPY_HW_UART2_CTS;
}
#endif
__USART2_CLK_ENABLE();
break;
#endif
#if defined(USART3) && defined(MICROPY_HW_UART3_PORT) && defined(MICROPY_HW_UART3_PINS)
// USART3 is on PB10/PB11 (CK,CTS,RTS on PB12,PB13,PB14), PC10/PC11 (CK on PC12), PD8/PD9 (CK on PD10)
case PYB_UART_3:
UARTx = USART3;
irqn = USART3_IRQn;
GPIO_AF_UARTx = GPIO_AF7_USART3;
GPIO_Port = MICROPY_HW_UART3_PORT;
GPIO_Pin = MICROPY_HW_UART3_PINS;
#if defined(MICROPY_HW_UART3_RTS)
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_RTS) {
GPIO_Pin |= MICROPY_HW_UART3_RTS;
}
#endif
#if defined(MICROPY_HW_UART3_CTS)
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_CTS) {
GPIO_Pin |= MICROPY_HW_UART3_CTS;
}
#endif
__USART3_CLK_ENABLE();
break;
#endif
#if defined(UART4) && defined(MICROPY_HW_UART4_PORT) && defined(MICROPY_HW_UART4_PINS)
// UART4 is on PA0/PA1, PC10/PC11
case PYB_UART_4:
UARTx = UART4;
irqn = UART4_IRQn;
GPIO_AF_UARTx = GPIO_AF8_UART4;
GPIO_Port = MICROPY_HW_UART4_PORT;
GPIO_Pin = MICROPY_HW_UART4_PINS;
__UART4_CLK_ENABLE();
break;
#endif
#if defined(UART5) && \
defined(MICROPY_HW_UART5_TX_PORT) && \
defined(MICROPY_HW_UART5_TX_PIN) && \
defined(MICROPY_HW_UART5_RX_PORT) && \
defined(MICROPY_HW_UART5_RX_PIN)
case PYB_UART_5:
UARTx = UART5;
irqn = UART5_IRQn;
GPIO_AF_UARTx = GPIO_AF8_UART5;
GPIO_Port = MICROPY_HW_UART5_TX_PORT;
GPIO_Port2 = MICROPY_HW_UART5_RX_PORT;
GPIO_Pin = MICROPY_HW_UART5_TX_PIN;
GPIO_Pin2 = MICROPY_HW_UART5_RX_PIN;
__UART5_CLK_ENABLE();
break;
#endif
#if defined(MICROPY_HW_UART6_PORT) && defined(MICROPY_HW_UART6_PINS)
// USART6 is on PC6/PC7 (CK on PC8)
case PYB_UART_6:
UARTx = USART6;
irqn = USART6_IRQn;
GPIO_AF_UARTx = GPIO_AF8_USART6;
GPIO_Port = MICROPY_HW_UART6_PORT;
GPIO_Pin = MICROPY_HW_UART6_PINS;
__USART6_CLK_ENABLE();
break;
#endif
default:
// UART does not exist or is not configured for this board
return false;
}
uart_obj->irqn = irqn;
uart_obj->uart.Instance = UARTx;
// init GPIO
mp_hal_gpio_clock_enable(GPIO_Port);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.Pin = GPIO_Pin;
GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
GPIO_InitStructure.Mode = GPIO_MODE_AF_PP;
GPIO_InitStructure.Pull = GPIO_PULLUP;
GPIO_InitStructure.Alternate = GPIO_AF_UARTx;
HAL_GPIO_Init(GPIO_Port, &GPIO_InitStructure);
// init GPIO for second pin if needed
if (GPIO_Port2 != NULL) {
mp_hal_gpio_clock_enable(GPIO_Port2);
GPIO_InitStructure.Pin = GPIO_Pin2;
HAL_GPIO_Init(GPIO_Port2, &GPIO_InitStructure);
}
// init UARTx
HAL_UART_Init(&uart_obj->uart);
uart_obj->is_enabled = true;
return true;
}
void serial_init(serial_t *obj, PinName tx, PinName rx)
{
struct serial_s *obj_s = SERIAL_S(obj);
// Determine the UART to use (UART_1, UART_2, ...)
UARTName uart_tx = (UARTName)pinmap_peripheral(tx, PinMap_UART_TX);
UARTName uart_rx = (UARTName)pinmap_peripheral(rx, PinMap_UART_RX);
// Get the peripheral name (UART_1, UART_2, ...) from the pin and assign it to the object
obj_s->uart = (UARTName)pinmap_merge(uart_tx, uart_rx);
MBED_ASSERT(obj_s->uart != (UARTName)NC);
// Enable USART clock + switch to SystemClock
if (obj_s->uart == UART_1) {
__USART1_FORCE_RESET();
__USART1_RELEASE_RESET();
__USART1_CLK_ENABLE();
#if defined(RCC_USART1CLKSOURCE_SYSCLK)
__HAL_RCC_USART1_CONFIG(RCC_USART1CLKSOURCE_SYSCLK);
#endif
obj_s->index = 0;
}
#if defined(USART2_BASE)
if (obj_s->uart == UART_2) {
__USART2_FORCE_RESET();
__USART2_RELEASE_RESET();
__USART2_CLK_ENABLE();
#if defined(RCC_USART2CLKSOURCE_SYSCLK)
__HAL_RCC_USART2_CONFIG(RCC_USART2CLKSOURCE_SYSCLK);
#endif
obj_s->index = 1;
}
#endif
#if defined(USART3_BASE)
if (obj_s->uart == UART_3) {
__USART3_FORCE_RESET();
__USART3_RELEASE_RESET();
__USART3_CLK_ENABLE();
#if defined(RCC_USART3CLKSOURCE_SYSCLK)
__HAL_RCC_USART3_CONFIG(RCC_USART3CLKSOURCE_SYSCLK);
#endif
obj_s->index = 2;
}
#endif
#if defined(UART4_BASE)
if (obj_s->uart == UART_4) {
__UART4_FORCE_RESET();
__UART4_RELEASE_RESET();
__UART4_CLK_ENABLE();
#if defined(RCC_UART4CLKSOURCE_SYSCLK)
__HAL_RCC_UART4_CONFIG(RCC_UART4CLKSOURCE_SYSCLK);
#endif
obj_s->index = 3;
}
#endif
#if defined(UART5_BASE)
if (obj_s->uart == UART_5) {
__HAL_RCC_UART5_FORCE_RESET();
__HAL_RCC_UART5_RELEASE_RESET();
__UART5_CLK_ENABLE();
#if defined(RCC_UART5CLKSOURCE_SYSCLK)
__HAL_RCC_UART5_CONFIG(RCC_UART5CLKSOURCE_SYSCLK);
#endif
obj_s->index = 4;
}
#endif
// Configure the UART pins
pinmap_pinout(tx, PinMap_UART_TX);
pinmap_pinout(rx, PinMap_UART_RX);
if (tx != NC) {
pin_mode(tx, PullUp);
}
if (rx != NC) {
pin_mode(rx, PullUp);
}
// Configure UART
obj_s->baudrate = 9600;
obj_s->databits = UART_WORDLENGTH_8B;
obj_s->stopbits = UART_STOPBITS_1;
obj_s->parity = UART_PARITY_NONE;
#if DEVICE_SERIAL_FC
obj_s->hw_flow_ctl = UART_HWCONTROL_NONE;
#endif
obj_s->pin_tx = tx;
obj_s->pin_rx = rx;
init_uart(obj);
// For stdio management
if (obj_s->uart == STDIO_UART) {
stdio_uart_inited = 1;
memcpy(&stdio_uart, obj, sizeof(serial_t));
}
}
// assumes Init parameters have been set up correctly
STATIC bool uart_init2(pyb_uart_obj_t *uart_obj) {
USART_TypeDef *UARTx;
IRQn_Type irqn;
int uart_unit;
const pin_obj_t *pins[4] = {0};
switch (uart_obj->uart_id) {
#if defined(MICROPY_HW_UART1_TX) && defined(MICROPY_HW_UART1_RX)
case PYB_UART_1:
uart_unit = 1;
UARTx = USART1;
irqn = USART1_IRQn;
pins[0] = &MICROPY_HW_UART1_TX;
pins[1] = &MICROPY_HW_UART1_RX;
__USART1_CLK_ENABLE();
break;
#endif
#if defined(MICROPY_HW_UART2_TX) && defined(MICROPY_HW_UART2_RX)
case PYB_UART_2:
uart_unit = 2;
UARTx = USART2;
irqn = USART2_IRQn;
pins[0] = &MICROPY_HW_UART2_TX;
pins[1] = &MICROPY_HW_UART2_RX;
#if defined(MICROPY_HW_UART2_RTS)
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_RTS) {
pins[2] = &MICROPY_HW_UART2_RTS;
}
#endif
#if defined(MICROPY_HW_UART2_CTS)
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_CTS) {
pins[3] = &MICROPY_HW_UART2_CTS;
}
#endif
__USART2_CLK_ENABLE();
break;
#endif
#if defined(MICROPY_HW_UART3_TX) && defined(MICROPY_HW_UART3_RX)
case PYB_UART_3:
uart_unit = 3;
UARTx = USART3;
irqn = USART3_IRQn;
pins[0] = &MICROPY_HW_UART3_TX;
pins[1] = &MICROPY_HW_UART3_RX;
#if defined(MICROPY_HW_UART3_RTS)
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_RTS) {
pins[2] = &MICROPY_HW_UART3_RTS;
}
#endif
#if defined(MICROPY_HW_UART3_CTS)
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_CTS) {
pins[3] = &MICROPY_HW_UART3_CTS;
}
#endif
__USART3_CLK_ENABLE();
break;
#endif
#if defined(MICROPY_HW_UART4_TX) && defined(MICROPY_HW_UART4_RX)
case PYB_UART_4:
uart_unit = 4;
UARTx = UART4;
irqn = UART4_IRQn;
pins[0] = &MICROPY_HW_UART4_TX;
pins[1] = &MICROPY_HW_UART4_RX;
__UART4_CLK_ENABLE();
break;
#endif
#if defined(MICROPY_HW_UART5_TX) && defined(MICROPY_HW_UART5_RX)
case PYB_UART_5:
uart_unit = 5;
UARTx = UART5;
irqn = UART5_IRQn;
pins[0] = &MICROPY_HW_UART5_TX;
pins[1] = &MICROPY_HW_UART5_RX;
__UART5_CLK_ENABLE();
break;
#endif
#if defined(MICROPY_HW_UART6_TX) && defined(MICROPY_HW_UART6_RX)
case PYB_UART_6:
uart_unit = 6;
UARTx = USART6;
irqn = USART6_IRQn;
pins[0] = &MICROPY_HW_UART6_TX;
pins[1] = &MICROPY_HW_UART6_RX;
#if defined(MICROPY_HW_UART6_RTS)
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_RTS) {
pins[2] = &MICROPY_HW_UART6_RTS;
}
#endif
#if defined(MICROPY_HW_UART6_CTS)
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_CTS) {
pins[3] = &MICROPY_HW_UART6_CTS;
}
#endif
__USART6_CLK_ENABLE();
break;
#endif
#if defined(MICROPY_HW_UART7_TX) && defined(MICROPY_HW_UART7_RX)
case PYB_UART_7:
uart_unit = 7;
UARTx = UART7;
irqn = UART7_IRQn;
pins[0] = &MICROPY_HW_UART7_TX;
pins[1] = &MICROPY_HW_UART7_RX;
__UART7_CLK_ENABLE();
break;
#endif
#if defined(MICROPY_HW_UART8_TX) && defined(MICROPY_HW_UART8_RX)
case PYB_UART_8:
uart_unit = 8;
UARTx = UART8;
irqn = UART8_IRQn;
pins[0] = &MICROPY_HW_UART8_TX;
pins[1] = &MICROPY_HW_UART8_RX;
__UART8_CLK_ENABLE();
break;
#endif
default:
// UART does not exist or is not configured for this board
return false;
}
uint32_t mode = MP_HAL_PIN_MODE_ALT;
uint32_t pull = MP_HAL_PIN_PULL_UP;
for (uint i = 0; i < 4; i++) {
if (pins[i] != NULL) {
bool ret = mp_hal_pin_config_alt(pins[i], mode, pull, AF_FN_UART, uart_unit);
if (!ret) {
return false;
}
}
}
uart_obj->irqn = irqn;
uart_obj->uart.Instance = UARTx;
// init UARTx
HAL_UART_Init(&uart_obj->uart);
uart_obj->is_enabled = true;
return true;
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART1)
{
/* USER CODE BEGIN USART1_MspInit 0 */
/* USER CODE END USART1_MspInit 0 */
/* Peripheral clock enable */
__USART1_CLK_ENABLE();
/**USART1 GPIO Configuration
PA9 ------> USART1_TX
PA10 ------> USART1_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_10;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* USER CODE BEGIN USART1_MspInit 1 */
/* USER CODE END USART1_MspInit 1 */
}
else if(huart->Instance==USART2)
{
/* USER CODE BEGIN USART2_MspInit 0 */
/* USER CODE END USART2_MspInit 0 */
/* Peripheral clock enable */
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_2;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(USART2_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(USART2_IRQn);
/* USER CODE BEGIN USART2_MspInit 1 */
/* USER CODE END USART2_MspInit 1 */
}
}
// assumes Init parameters have been set up correctly
STATIC bool uart_init2(pyb_uart_obj_t *uart_obj) {
USART_TypeDef *UARTx;
IRQn_Type irqn;
uint32_t GPIO_Pin;
uint8_t GPIO_AF_UARTx = 0;
GPIO_TypeDef* GPIO_Port = NULL;
switch (uart_obj->uart_id) {
// USART1 is on PA9/PA10 (CK on PA8), PB6/PB7
case PYB_UART_1:
UARTx = USART1;
irqn = USART1_IRQn;
GPIO_AF_UARTx = GPIO_AF7_USART1;
#if defined (PYBV4) || defined(PYBV10)
GPIO_Port = GPIOB;
GPIO_Pin = GPIO_PIN_6 | GPIO_PIN_7;
#else
GPIO_Port = GPIOA;
GPIO_Pin = GPIO_PIN_9 | GPIO_PIN_10;
#endif
__USART1_CLK_ENABLE();
break;
// USART2 is on PA2/PA3 (CTS,RTS,CK on PA0,PA1,PA4), PD5/PD6 (CK on PD7)
case PYB_UART_2:
UARTx = USART2;
irqn = USART2_IRQn;
GPIO_AF_UARTx = GPIO_AF7_USART2;
GPIO_Port = GPIOA;
GPIO_Pin = GPIO_PIN_2 | GPIO_PIN_3;
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_RTS) {
GPIO_Pin |= GPIO_PIN_1;
}
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_CTS) {
GPIO_Pin |= GPIO_PIN_0;
}
__USART2_CLK_ENABLE();
break;
// USART3 is on PB10/PB11 (CK,CTS,RTS on PB12,PB13,PB14), PC10/PC11 (CK on PC12), PD8/PD9 (CK on PD10)
case PYB_UART_3:
UARTx = USART3;
irqn = USART3_IRQn;
GPIO_AF_UARTx = GPIO_AF7_USART3;
#if defined(PYBV3) || defined(PYBV4) | defined(PYBV10)
GPIO_Port = GPIOB;
GPIO_Pin = GPIO_PIN_10 | GPIO_PIN_11;
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_RTS) {
GPIO_Pin |= GPIO_PIN_14;
}
if (uart_obj->uart.Init.HwFlowCtl & UART_HWCONTROL_CTS) {
GPIO_Pin |= GPIO_PIN_13;
}
#else
GPIO_Port = GPIOD;
GPIO_Pin = GPIO_PIN_8 | GPIO_PIN_9;
#endif
__USART3_CLK_ENABLE();
break;
// UART4 is on PA0/PA1, PC10/PC11
case PYB_UART_4:
UARTx = UART4;
irqn = UART4_IRQn;
GPIO_AF_UARTx = GPIO_AF8_UART4;
GPIO_Port = GPIOA;
GPIO_Pin = GPIO_PIN_0 | GPIO_PIN_1;
__UART4_CLK_ENABLE();
break;
// USART6 is on PC6/PC7 (CK on PC8)
case PYB_UART_6:
UARTx = USART6;
irqn = USART6_IRQn;
GPIO_AF_UARTx = GPIO_AF8_USART6;
GPIO_Port = GPIOC;
GPIO_Pin = GPIO_PIN_6 | GPIO_PIN_7;
__USART6_CLK_ENABLE();
break;
default:
return false;
}
uart_obj->irqn = irqn;
uart_obj->uart.Instance = UARTx;
// init GPIO
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.Pin = GPIO_Pin;
GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
GPIO_InitStructure.Mode = GPIO_MODE_AF_PP;
GPIO_InitStructure.Pull = GPIO_PULLUP;
GPIO_InitStructure.Alternate = GPIO_AF_UARTx;
HAL_GPIO_Init(GPIO_Port, &GPIO_InitStructure);
// init UARTx
HAL_UART_Init(&uart_obj->uart);
uart_obj->is_enabled = true;
return true;
}
// assumes Init parameters have been set up correctly
bool uart_init2(pyb_uart_obj_t *uart_obj) {
#if 0
USART_TypeDef *UARTx = NULL;
uint32_t GPIO_Pin = 0;
uint8_t GPIO_AF_UARTx = 0;
GPIO_TypeDef* GPIO_Port = NULL;
switch (uart_obj->uart_id) {
// USART1 is on PA9/PA10 (CK on PA8), PB6/PB7
case PYB_UART_1:
UARTx = USART1;
GPIO_AF_UARTx = GPIO_AF7_USART1;
#if defined (PYBV4) || defined(PYBV10)
GPIO_Port = GPIOB;
GPIO_Pin = GPIO_PIN_6 | GPIO_PIN_7;
#else
GPIO_Port = GPIOA;
GPIO_Pin = GPIO_PIN_9 | GPIO_PIN_10;
#endif
__USART1_CLK_ENABLE();
break;
// USART2 is on PA2/PA3 (CK on PA4), PD5/PD6 (CK on PD7)
case PYB_UART_2:
UARTx = USART2;
GPIO_AF_UARTx = GPIO_AF7_USART2;
GPIO_Port = GPIOA;
GPIO_Pin = GPIO_PIN_2 | GPIO_PIN_3;
__USART2_CLK_ENABLE();
break;
// USART3 is on PB10/PB11 (CK on PB12), PC10/PC11 (CK on PC12), PD8/PD9 (CK on PD10)
case PYB_UART_3:
UARTx = USART3;
GPIO_AF_UARTx = GPIO_AF7_USART3;
#if defined(PYBV3) || defined(PYBV4) | defined(PYBV10)
GPIO_Port = GPIOB;
GPIO_Pin = GPIO_PIN_10 | GPIO_PIN_11;
#else
GPIO_Port = GPIOD;
GPIO_Pin = GPIO_PIN_8 | GPIO_PIN_9;
#endif
__USART3_CLK_ENABLE();
break;
// UART4 is on PA0/PA1, PC10/PC11
case PYB_UART_4:
UARTx = UART4;
GPIO_AF_UARTx = GPIO_AF8_UART4;
GPIO_Port = GPIOA;
GPIO_Pin = GPIO_PIN_0 | GPIO_PIN_1;
__UART4_CLK_ENABLE();
break;
// USART6 is on PC6/PC7 (CK on PC8)
case PYB_UART_6:
UARTx = USART6;
GPIO_AF_UARTx = GPIO_AF8_USART6;
GPIO_Port = GPIOC;
GPIO_Pin = GPIO_PIN_6 | GPIO_PIN_7;
__USART6_CLK_ENABLE();
break;
default:
return false;
}
// init GPIO
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.Pin = GPIO_Pin;
GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
GPIO_InitStructure.Mode = GPIO_MODE_AF_PP;
GPIO_InitStructure.Pull = GPIO_PULLUP;
GPIO_InitStructure.Alternate = GPIO_AF_UARTx;
HAL_GPIO_Init(GPIO_Port, &GPIO_InitStructure);
// init UARTx
uart_obj->uart.Instance = UARTx;
HAL_UART_Init(&uart_obj->uart);
uart_obj->is_enabled = true;
#endif
return true;
}
void serial_init(serial_t *obj, PinName tx, PinName rx) {
// Determine the UART to use (UART_1, UART_2, ...)
UARTName uart_tx = (UARTName)pinmap_peripheral(tx, PinMap_UART_TX);
UARTName uart_rx = (UARTName)pinmap_peripheral(rx, PinMap_UART_RX);
// Get the peripheral name (UART_1, UART_2, ...) from the pin and assign it to the object
obj->uart = (UARTName)pinmap_merge(uart_tx, uart_rx);
MBED_ASSERT(obj->uart != (UARTName)NC);
// Enable USART clock
switch (obj->uart) {
case UART_1:
__USART1_CLK_ENABLE();
obj->index = 0;
break;
case UART_2:
__USART2_CLK_ENABLE();
obj->index = 1;
break;
case UART_3:
__USART3_CLK_ENABLE();
obj->index = 2;
break;
case UART_4:
__UART4_CLK_ENABLE();
obj->index = 3;
break;
case UART_5:
__UART5_CLK_ENABLE();
obj->index = 4;
break;
case UART_6:
__USART6_CLK_ENABLE();
obj->index = 5;
break;
}
// Configure the UART pins
pinmap_pinout(tx, PinMap_UART_TX);
pinmap_pinout(rx, PinMap_UART_RX);
if (tx != NC) {
pin_mode(tx, PullUp);
}
if (rx != NC) {
pin_mode(rx, PullUp);
}
// Configure UART
obj->baudrate = 9600;
obj->databits = UART_WORDLENGTH_8B;
obj->stopbits = UART_STOPBITS_1;
obj->parity = UART_PARITY_NONE;
obj->pin_tx = tx;
obj->pin_rx = rx;
init_uart(obj);
// For stdio management
if (obj->uart == STDIO_UART) {
stdio_uart_inited = 1;
memcpy(&stdio_uart, obj, sizeof(serial_t));
}
}
void usart_init(pyb_usart_obj_t *usart_obj, uint32_t baudrate) {
USART_TypeDef *USARTx=NULL;
uint32_t GPIO_Pin=0;
uint8_t GPIO_AF_USARTx=0;
GPIO_TypeDef* GPIO_Port=NULL;
switch (usart_obj->usart_id) {
case PYB_USART_NONE:
return;
case PYB_USART_1:
USARTx = USART1;
GPIO_Port = GPIOA;
GPIO_AF_USARTx = GPIO_AF7_USART1;
GPIO_Pin = GPIO_PIN_9 | GPIO_PIN_10;
__USART1_CLK_ENABLE();
break;
case PYB_USART_2:
USARTx = USART2;
GPIO_Port = GPIOD;
GPIO_AF_USARTx = GPIO_AF7_USART2;
GPIO_Pin = GPIO_PIN_5 | GPIO_PIN_6;
__USART2_CLK_ENABLE();
break;
case PYB_USART_3:
USARTx = USART3;
#if defined(PYBV3) || defined(PYBV4)
GPIO_Port = GPIOB;
GPIO_AF_USARTx = GPIO_AF7_USART3;
GPIO_Pin = GPIO_PIN_10 | GPIO_PIN_11;
#else
GPIO_Port = GPIOD;
GPIO_AF_USARTx = GPIO_AF7_USART3;
GPIO_Pin = GPIO_PIN_8 | GPIO_PIN_9;
#endif
__USART3_CLK_ENABLE();
break;
case PYB_USART_6:
USARTx = USART6;
GPIO_Port = GPIOC;
GPIO_AF_USARTx = GPIO_AF8_USART6;
GPIO_Pin = GPIO_PIN_6 | GPIO_PIN_7;
__USART6_CLK_ENABLE();
break;
}
// Initialize USARTx
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.Pin = GPIO_Pin;
GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
GPIO_InitStructure.Mode = GPIO_MODE_AF_PP;
GPIO_InitStructure.Pull = GPIO_PULLUP;
GPIO_InitStructure.Alternate = GPIO_AF_USARTx;
HAL_GPIO_Init(GPIO_Port, &GPIO_InitStructure);
UART_HandleTypeDef *uh = &usart_obj->handle;
memset(uh, 0, sizeof(*uh));
uh->Instance = USARTx;
uh->Init.BaudRate = baudrate;
uh->Init.WordLength = USART_WORDLENGTH_8B;
uh->Init.StopBits = USART_STOPBITS_1;
uh->Init.Parity = USART_PARITY_NONE;
uh->Init.Mode = USART_MODE_TX_RX;
uh->Init.HwFlowCtl = UART_HWCONTROL_NONE;
uh->Init.OverSampling = UART_OVERSAMPLING_16;
HAL_UART_Init(uh);
}
/**
* @brief UART MSP Initialization
* This function configures the hardware resources used in this example:
* - Peripheral's clock enable
* - Peripheral's GPIO Configuration
* @param huart: UART handle pointer
* @retval None
*/
void HAL_UART_MspInit(UART_HandleTypeDef *huart)
{
if (huart->Instance == USART2) {
GPIO_InitTypeDef GPIO_InitStruct;
/*##-1- Enable peripherals and GPIO Clocks #################################*/
/* Enable GPIO TX/RX clock */
USART2_TX_GPIO_CLK_ENABLE();
USART2_RX_GPIO_CLK_ENABLE();
/* Enable USART2 clock */
__USART2_CLK_ENABLE();
/*##-2- Configure peripheral GPIO ##########################################*/
/* UART TX GPIO pin configuration */
GPIO_InitStruct.Pin = USART2_TX_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
GPIO_InitStruct.Alternate = USART2_TX_AF;
HAL_GPIO_Init(USART2_TX_PORT, &GPIO_InitStruct);
/* UART RX GPIO pin configuration */
GPIO_InitStruct.Pin = USART2_RX_PIN;
GPIO_InitStruct.Alternate = USART2_RX_AF;
HAL_GPIO_Init(USART2_RX_PORT, &GPIO_InitStruct);
/* Enable RXNE interrupt */
__HAL_UART_ENABLE_IT(huart, UART_IT_RXNE);
NVIC_SetPriority(USART2_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY + 3);
NVIC_EnableIRQ(USART2_IRQn);
} else if (huart->Instance==USART6) {
GPIO_InitTypeDef GPIO_InitStruct;
/* Peripheral clock enable */
__USART6_CLK_ENABLE();
USART6_TX_GPIO_CLK_ENABLE();
USART6_RX_GPIO_CLK_ENABLE();
/* USART6 GPIO Configuration */
/* TODO: Temproray fix to disable USART6 TX pin. I made a mistake to
swap the TX and RX pin for the MPU6050 module... */
GPIO_InitStruct.Pin = USART6_TX_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT; //GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL; //GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = 0; //USART6_TX_AF;
HAL_GPIO_Init(USART6_TX_PORT, &GPIO_InitStruct);
GPIO_InitStruct.Pin = USART6_RX_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = USART6_RX_AF;
HAL_GPIO_Init(USART6_RX_PORT, &GPIO_InitStruct);
} else if (huart->Instance==USART1) {
GPIO_InitTypeDef GPIO_InitStruct;
/* Peripheral clock enable */
__USART1_CLK_ENABLE();
USART1_TX_GPIO_CLK_ENABLE();
USART1_RX_GPIO_CLK_ENABLE();
/* USART1 GPIO Configuration */
GPIO_InitStruct.Pin = USART1_TX_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = USART1_TX_AF;
HAL_GPIO_Init(USART1_TX_PORT, &GPIO_InitStruct);
GPIO_InitStruct.Pin = USART1_RX_PIN;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = USART1_RX_AF;
HAL_GPIO_Init(USART1_RX_PORT, &GPIO_InitStruct);
}
}
void HAL_UART_MspInit(UART_HandleTypeDef* huart)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(huart->Instance==USART2)
{
/* USER CODE BEGIN USART2_MspInit 0 */
/* USER CODE END USART2_MspInit 0 */
/* Peripheral clock enable */
__USART2_CLK_ENABLE();
/**USART2 GPIO Configuration
PA2 ------> USART2_TX
PA3 ------> USART2_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_2|GPIO_PIN_3;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
/* Peripheral DMA init*/
hdma_usart2_rx.Instance = DMA1_Stream5;
hdma_usart2_rx.Init.Channel = DMA_CHANNEL_4;
hdma_usart2_rx.Init.Direction = DMA_PERIPH_TO_MEMORY;
hdma_usart2_rx.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_usart2_rx.Init.MemInc = DMA_MINC_ENABLE;
hdma_usart2_rx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
hdma_usart2_rx.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
hdma_usart2_rx.Init.Mode = DMA_NORMAL;
hdma_usart2_rx.Init.Priority = DMA_PRIORITY_LOW;
hdma_usart2_rx.Init.FIFOMode = DMA_FIFOMODE_DISABLE;
HAL_DMA_Init(&hdma_usart2_rx);
__HAL_LINKDMA(huart,hdmarx,hdma_usart2_rx);
hdma_usart2_tx.Instance = DMA1_Stream6;
hdma_usart2_tx.Init.Channel = DMA_CHANNEL_4;
hdma_usart2_tx.Init.Direction = DMA_MEMORY_TO_PERIPH;
hdma_usart2_tx.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_usart2_tx.Init.MemInc = DMA_MINC_ENABLE;
hdma_usart2_tx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
hdma_usart2_tx.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
hdma_usart2_tx.Init.Mode = DMA_NORMAL;
hdma_usart2_tx.Init.Priority = DMA_PRIORITY_LOW;
hdma_usart2_tx.Init.FIFOMode = DMA_FIFOMODE_DISABLE;
HAL_DMA_Init(&hdma_usart2_tx);
__HAL_LINKDMA(huart,hdmatx,hdma_usart2_tx);
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(USART2_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(USART2_IRQn);
/* USER CODE BEGIN USART2_MspInit 1 */
__HAL_UART_ENABLE_IT(huart, UART_IT_RXNE); //|UART_IT_IDLE
/* USER CODE END USART2_MspInit 1 */
}
else if(huart->Instance==USART3)
{
/* USER CODE BEGIN USART3_MspInit 0 */
/* USER CODE END USART3_MspInit 0 */
/* Peripheral clock enable */
__USART3_CLK_ENABLE();
/**USART3 GPIO Configuration
PD8 ------> USART3_TX
PD9 ------> USART3_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_8|GPIO_PIN_9;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
/* Peripheral DMA init*/
hdma_usart3_rx.Instance = DMA1_Stream1;
hdma_usart3_rx.Init.Channel = DMA_CHANNEL_4;
hdma_usart3_rx.Init.Direction = DMA_PERIPH_TO_MEMORY;
hdma_usart3_rx.Init.PeriphInc = DMA_PINC_DISABLE;
hdma_usart3_rx.Init.MemInc = DMA_MINC_ENABLE;
hdma_usart3_rx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
hdma_usart3_rx.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
hdma_usart3_rx.Init.Mode = DMA_CIRCULAR;
hdma_usart3_rx.Init.Priority = DMA_PRIORITY_LOW;
hdma_usart3_rx.Init.FIFOMode = DMA_FIFOMODE_DISABLE;
HAL_DMA_Init(&hdma_usart3_rx);
__HAL_LINKDMA(huart,hdmarx,hdma_usart3_rx);
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(USART3_IRQn, 2, 0);
HAL_NVIC_EnableIRQ(USART3_IRQn);
/* USER CODE BEGIN USART3_MspInit 1 */
/* USER CODE END USART3_MspInit 1 */
}
else if(huart->Instance==USART6)
{
/* USER CODE BEGIN USART6_MspInit 0 */
/* USER CODE END USART6_MspInit 0 */
/* Peripheral clock enable */
__USART6_CLK_ENABLE();
/**USART6 GPIO Configuration
PC6 ------> USART6_TX
PC7 ------> USART6_RX
*/
GPIO_InitStruct.Pin = GPIO_PIN_6|GPIO_PIN_7;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_PULLUP;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF8_USART6;
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
/* USER CODE BEGIN USART6_MspInit 1 */
/* USER CODE END USART6_MspInit 1 */
}
}
void serial_init(serial_t *obj, PinName tx, PinName rx)
{
// Determine the UART to use (UART_1, UART_2, ...)
UARTName uart_tx = (UARTName)pinmap_peripheral(tx, PinMap_UART_TX);
UARTName uart_rx = (UARTName)pinmap_peripheral(rx, PinMap_UART_RX);
// Get the peripheral name (UART_1, UART_2, ...) from the pin and assign it to the object
UARTName instance = (UARTName)pinmap_merge(uart_tx, uart_rx);
MBED_ASSERT(instance != (UARTName)NC);
// Enable USART clock
switch (instance) {
case UART_1:
__USART1_CLK_ENABLE();
obj->serial.module = 0;
break;
case UART_2:
__USART2_CLK_ENABLE();
obj->serial.module = 1;
break;
#if defined(USART3_BASE)
case UART_3:
__USART3_CLK_ENABLE();
obj->serial.module = 2;
break;
#endif
#if defined(UART4_BASE)
case UART_4:
__UART4_CLK_ENABLE();
obj->serial.module = 3;
break;
#endif
#if defined(UART5_BASE)
case UART_5:
__UART5_CLK_ENABLE();
obj->serial.module = 4;
break;
#endif
case UART_6:
__USART6_CLK_ENABLE();
obj->serial.module = 5;
break;
#if defined(UART7_BASE)
case UART_7:
__UART7_CLK_ENABLE();
obj->serial.module = 6;
break;
#endif
#if defined(UART8_BASE)
case UART_8:
__UART8_CLK_ENABLE();
obj->serial.module = 7;
break;
#endif
}
// Configure the UART pins
pinmap_pinout(tx, PinMap_UART_TX);
pinmap_pinout(rx, PinMap_UART_RX);
if (tx != NC) pin_mode(tx, PullUp);
if (rx != NC) pin_mode(rx, PullUp);
obj->serial.pin_tx = tx;
obj->serial.pin_rx = rx;
// initialize the handle for this master!
UART_HandleTypeDef *handle = &UartHandle[obj->serial.module];
handle->Instance = (USART_TypeDef *)instance;
handle->Init.BaudRate = 9600;
handle->Init.WordLength = UART_WORDLENGTH_8B;
handle->Init.StopBits = UART_STOPBITS_1;
handle->Init.Parity = UART_PARITY_NONE;
if (rx == NC) {
handle->Init.Mode = UART_MODE_TX;
} else if (tx == NC) {
handle->Init.Mode = UART_MODE_RX;
} else {
handle->Init.Mode = UART_MODE_TX_RX;
}
handle->Init.HwFlowCtl = UART_HWCONTROL_NONE;
handle->Init.OverSampling = UART_OVERSAMPLING_16;
handle->TxXferCount = 0;
handle->RxXferCount = 0;
if (tx == STDIO_UART_TX && rx == STDIO_UART_RX) {
handle->Init.BaudRate = YOTTA_CFG_MBED_OS_STDIO_DEFAULT_BAUD;
}
HAL_UART_Init(handle);
// DEBUG_PRINTF("UART%u: Init\n", obj->serial.module+1);
}