static void
mpreset(void)
{
/* stop application processors */
mpshutdown();
/* do generic reset */
archreset();
}
void
main(void)
{
extern char edata[], end[];
uint rev;
okay(1);
m = (Mach*)MACHADDR;
memset(edata, 0, end - edata); /* clear bss */
machinit();
mmuinit1();
optionsinit("/boot/boot boot");
quotefmtinstall();
ataginit((Atag*)BOOTARGS);
confinit(); /* figures out amount of memory */
xinit();
uartconsinit();
screeninit();
print("\nPlan 9 from Bell Labs\n");
rev = getfirmware();
print("firmware: rev %d\n", rev);
if(rev < Minfirmrev){
print("Sorry, firmware (start.elf) must be at least rev %d (%s)\n",
Minfirmrev, Minfirmdate);
for(;;)
;
}
trapinit();
clockinit();
printinit();
timersinit();
cpuidprint();
archreset();
procinit0();
initseg();
links();
chandevreset(); /* most devices are discovered here */
pageinit();
swapinit();
userinit();
gpiomeminit();
schedinit();
assert(0); /* shouldn't have returned */
}
void
exit(int ispanic)
{
shutdown(ispanic);
archreset();
}
/*
* entered from l.s with mmu enabled.
*
* we may have to realign the data segment; apparently 5l -H0 -R4096
* does not pad the text segment. on the other hand, we may have been
* loaded by another kernel.
*
* be careful not to touch the data segment until we know it's aligned.
*/
void
main(Mach* mach)
{
extern char bdata[], edata[], end[], etext[];
static ulong vfy = 0xcafebabe;
m = mach;
if (vfy != 0xcafebabe)
memmove(bdata, etext, edata - bdata);
if (vfy != 0xcafebabe) {
wave('?');
panic("misaligned data segment");
}
memset(edata, 0, end - edata); /* zero bss */
vfy = 0;
wave('9');
machinit();
archreset();
mmuinit();
optionsinit("/boot/boot boot");
quotefmtinstall();
archconsole();
wave(' ');
/* want plan9.ini to be able to affect memory sizing in confinit */
plan9iniinit(); /* before we step on plan9.ini in low memory */
/* set memsize before xinit */
confinit();
/* xinit would print if it could */
xinit();
/*
* Printinit will cause the first malloc call.
* (printinit->qopen->malloc) unless any of the
* above (like clockintr) do an irqenable, which
* will call malloc.
* If the system dies here it's probably due
* to malloc(->xalloc) not being initialised
* correctly, or the data segment is misaligned
* (it's amazing how far you can get with
* things like that completely broken).
*
* (Should be) boilerplate from here on.
*/
trapinit();
clockinit();
printinit();
uartkirkwoodconsole();
/* only now can we print */
print("from Bell Labs\n\n");
#ifdef CRYPTOSANDBOX
print("sandbox: 64K at physical %#lux, mapped to 0xf10b0000\n",
PADDR((uintptr)sandbox & ~(BY2PG-1)));
#endif
archconfinit();
cpuidprint();
timersinit();
procinit0();
initseg();
links();
chandevreset(); /* most devices are discovered here */
spiprobe();
pageinit();
swapinit();
userinit();
schedinit();
panic("schedinit returned");
}
/*
* at entry, l.s has set m for cpu0 and printed "Plan 9 from Be"
* but has not zeroed bss.
*/
void
main(void)
{
int cpu;
static ulong vfy = 0xcafebabe;
up = nil;
if (vfy != 0xcafebabe) {
serialputc('?');
serialputc('d');
panic("data segment misaligned");
}
memset(edata, 0, end - edata);
/*
* we can't lock until smpon has run, but we're supposed to wait
* until l1 & l2 are on. too bad. l1 is on, l2 will soon be.
*/
smpon();
iprint("ll Labs ");
cacheinit();
/*
* data segment is aligned, bss is zeroed, caches' characteristics
* are known. begin initialisation.
*/
mach0init();
l2pageinit();
mmuinit();
optionsinit("/boot/boot boot");
quotefmtinstall();
/* want plan9.ini to be able to affect memory sizing in confinit */
plan9iniinit(); /* before we step on plan9.ini in low memory */
/* l2 looks for *l2off= in plan9.ini */
l2cache->on(); /* l2->on requires locks to work, thus smpon */
l2cache->info(&cachel[2]);
allcache->on();
cortexa9cachecfg();
trapinit(); /* so confinit can probe memory to size it */
confinit(); /* figures out amount of memory */
/* xinit prints (if it can), so finish up the banner here. */
delay(100);
navailcpus = getncpus();
iprint("(mp arm; %d cpus)\n\n", navailcpus);
delay(100);
for (cpu = 1; cpu < navailcpus; cpu++)
stopcpu(cpu);
xinit();
irqtooearly = 0; /* now that xinit and trapinit have run */
mainmem->flags |= POOL_ANTAGONISM /* | POOL_PARANOIA */ ;
/*
* Printinit will cause the first malloc call.
* (printinit->qopen->malloc) unless any of the
* above (like clockinit) do an irqenable, which
* will call malloc.
* If the system dies here it's probably due
* to malloc(->xalloc) not being initialised
* correctly, or the data segment is misaligned
* (it's amazing how far you can get with
* things like that completely broken).
*
* (Should be) boilerplate from here on.
*/
archreset(); /* cfg clock signals, print cache cfg */
clockinit(); /* start clocks */
timersinit();
delay(50); /* let uart catch up */
printinit();
kbdenable();
cpuidprint();
chkmissing();
procinit0();
initseg();
// dmainit();
links();
conf.monitor = 1;
// screeninit();
iprint("pcireset...");
pcireset(); /* this tends to hang after a reboot */
iprint("ok\n");
chandevreset(); /* most devices are discovered here */
// i8250console(); /* too early; see init0 */
pageinit(); /* prints "1020M memory: ⋯ */
swapinit();
userinit();
/*
* starting a cpu will eventually result in it calling schedinit,
* so everything necessary to run user processes should be set up
* before starting secondary cpus.
*/
launchinit();
/* SMP & FW are already on when we get here; u-boot set them? */
for (cpu = 1; cpu < navailcpus; cpu++)
if (startcpu(cpu) < 0)
panic("cpu%d didn't start", cpu);
l1diag();
schedinit();
panic("cpu%d: schedinit returned", m->machno);
}
void
main(void)
{
int machno;
/* entry to main pushed stuff onto the stack. */
// memset(edata, 0, (ulong)end-(ulong)edata);
machno = getpir();
if (machno > 0)
startcpu(machno);
// dcrcompile();
if (dverify != 0x01020304) {
uartlputs("data segment not initialised\n");
panic("data segment not initialised");
}
if (bverify != 0) {
uartlputs("bss segment not zeroed\n");
panic("bss segment not zeroed");
}
mach0init();
archreset();
quotefmtinstall();
optionsinit("/boot/boot boot");
// archconsole();
meminit();
confinit();
mmuinit();
xinit(); /* xinit would print if it could */
trapinit();
qtminit();
ioinit();
uncinit();
printinit();
uartliteconsole();
mainmem->flags |= POOL_ANTAGONISM;
mainmem->panic = mypanic;
ethermedium.maxtu = 1512; /* must be multiple of 4 for temac's dma */
// print("\n\nPlan 9k H\n"); /* already printed by l.s */
plan9iniinit();
timersinit();
clockinit();
dma0init(); /* does not start kprocs; see init0 */
fpuinit();
procinit0();
initseg();
links();
chandevreset();
okprint = 1; /* only now can we print */
barriers();
dcflush((uintptr)&okprint, sizeof okprint);
cpuidprint();
print("%d Hz clock", HZ);
print("; memory size %,ud (%#ux)\n", (uint)memsz, (uint)memsz);
pageinit();
swapinit();
userinit();
active.thunderbirdsarego = 1;
dcflush((uintptr)&active.thunderbirdsarego,
sizeof active.thunderbirdsarego);
schedinit();
/* no return */
panic("schedinit returned");
}
void
main(void)
{
// int i;
extern char bdata[], edata[], end[], etext[];
static ulong vfy = 0xcafebabe;
/* l.s has already printed "Plan 9 from Be" */
// m = mach; /* now done in l.s */
/* realign data seg; apparently -H0 -R4096 does not pad the text seg */
if (vfy != 0xcafebabe) {
// wave('<'); wave('-');
memmove(bdata, etext, edata - bdata);
}
/*
* once data segment is in place, always zero bss since we may
* have been loaded by another Plan 9 kernel.
*/
memset(edata, 0, end - edata); /* zero BSS */
cacheuwbinv();
l2cacheuwbinv();
if (vfy != 0xcafebabe)
panic("data segment misaligned");
vfy = 0;
wave('l');
machinit();
mmuinit();
optionsinit("/boot/boot boot");
quotefmtinstall();
/* want plan9.ini to be able to affect memory sizing in confinit */
plan9iniinit(); /* before we step on plan9.ini in low memory */
trapinit(); /* so confinit can probe memory to size it */
confinit(); /* figures out amount of memory */
/* xinit prints (if it can), so finish up the banner here. */
delay(500);
iprint("l Labs\n\n");
delay(500);
xinit();
mainmem->flags |= POOL_ANTAGONISM /* | POOL_PARANOIA */ ;
/*
* Printinit will cause the first malloc call.
* (printinit->qopen->malloc) unless any of the
* above (like clockinit) do an irqenable, which
* will call malloc.
* If the system dies here it's probably due
* to malloc(->xalloc) not being initialised
* correctly, or the data segment is misaligned
* (it's amazing how far you can get with
* things like that completely broken).
*
* (Should be) boilerplate from here on.
*/
archreset(); /* configure clock signals */
clockinit(); /* start clocks */
timersinit();
watchdoginit();
delay(250); /* let uart catch up */
printinit();
// kbdenable();
cpuidprint();
// chkmissing();
procinit0();
initseg();
dmainit();
links();
conf.monitor = 1;
screeninit();
chandevreset(); /* most devices are discovered here */
// i8250console(); /* too early; see init0 */
pageinit();
swapinit();
userinit();
schedinit();
}
