static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* NAND */
ek_add_device_nand();
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* MMC */
at91_add_device_mmc(0, &ek_mmc_data);
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
/* Push Buttons */
ek_add_device_buttons();
/* PCK0 provides MCLK to the WM8731 */
at91_set_B_periph(AT91_PIN_PC1, 0);
/* SSC (for WM8731) */
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
}
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* NAND */
ek_add_device_nand();
/* DM9000 ethernet */
ek_add_device_dm9000();
/* spi0 and mmc/sd share the same PIO pins */
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* Touchscreen */
ek_add_device_ts();
/* SSC (to AT73C213) */
at73c213_set_clk(&at73c213_data);
at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX);
#else
/* MMC */
at91_add_device_mmc(0, &ek_mmc_data);
#endif
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
/* Push Buttons */
ek_add_device_buttons();
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* NAND */
ek_add_device_nand();
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* MMC */
at91_add_device_mmc(0, &ek_mmc_data);
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* SSC (to AT73C213) */
at73c213_set_clk(&at73c213_data);
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
/* Push Buttons */
ek_add_device_buttons();
}
static void __init ek_board_init(void)
{
at91_add_device_serial();
at91_add_device_usbh(&ek_usbh_data);
at91_add_device_udc(&ek_udc_data);
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
ek_add_device_nand();
at91_add_device_eth(&ek_macb_data);
#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
at91_add_device_mci(0, &ek_mmc_data);
#else
at91_add_device_mmc(0, &ek_mmc_data);
#endif
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
at91_set_B_periph(AT91_PIN_PC1, 0);
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
}
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* NAND */
ek_add_device_nand();
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* MMC */
at91_add_device_mmc(0, &ek_mmc_data);
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* Compact Flash */
at91_add_device_cf(&ek_cf_data);
/* SSC (to AT73C213) */
at73c213_set_clk(&at73c213_data);
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
/* Push Buttons */
ek_add_device_buttons();
/* shutdown controller, wakeup button (5 msec low) */
at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW
| AT91_SHDW_RTTWKEN);
}
static void __init afeb9260_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&afeb9260_usbh_data);
/* USB Device */
at91_add_device_udc(&afeb9260_udc_data);
/* SPI */
at91_add_device_spi(afeb9260_spi_devices,
ARRAY_SIZE(afeb9260_spi_devices));
/* NAND */
at91_add_device_nand(&afeb9260_nand_data);
/* Ethernet */
at91_add_device_eth(&afeb9260_macb_data);
/* Standard function's pin assignments are not
* appropriate for us and generic code provide
* no API to configure these pins any other way */
at91_set_B_periph(AT91_PIN_PA10, 0); /* ETX2 */
at91_set_B_periph(AT91_PIN_PA11, 0); /* ETX3 */
/* MMC */
at91_add_device_mmc(0, &afeb9260_mmc_data);
/* I2C */
at91_add_device_i2c(afeb9260_i2c_devices,
ARRAY_SIZE(afeb9260_i2c_devices));
/* Audio */
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
}
static void __init ek_board_init(void)
{
at91_add_device_serial();
at91_add_device_usbh(&ek_usbh_data);
at91_add_device_udc(&ek_udc_data);
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
ek_add_device_nand();
ek_add_device_macb();
ek_add_regulators();
ek_add_device_mmc();
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
ek_add_device_gpio_leds();
ek_add_device_buttons();
at91_set_B_periph(AT91_PIN_PC1, 0);
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
}
static void __init ek_board_init(void)
{
at91_add_device_serial();
at91_add_device_usbh(&ek_usbh_data);
at91_add_device_udc(&ek_udc_data);
at91_add_device_i2c(NULL, 0);
ek_add_device_nand();
ek_add_device_dm9000();
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
ek_add_device_ts();
at73c213_set_clk(&at73c213_data);
at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX);
#else
at91_add_device_mmc(0, &ek_mmc_data);
#endif
at91_add_device_lcdc(&ek_lcdc_data);
ek_add_device_buttons();
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
static void __init snapper9260_board_init(void)
{
at91_add_device_i2c(snapper9260_i2c_devices,
ARRAY_SIZE(snapper9260_i2c_devices));
at91_add_device_serial();
at91_add_device_usbh(&snapper9260_usbh_data);
at91_add_device_udc(&snapper9260_udc_data);
at91_add_device_eth(&snapper9260_macb_data);
at91_add_device_ssc(AT91SAM9260_ID_SSC, (ATMEL_SSC_TF | ATMEL_SSC_TK |
ATMEL_SSC_TD | ATMEL_SSC_RD));
snapper9260_add_device_nand();
}
static void __init dk_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* Ethernet */
at91_add_device_eth(&dk_eth_data);
/* USB Host */
at91_add_device_usbh(&dk_usbh_data);
/* USB Device */
at91_add_device_udc(&dk_udc_data);
at91_set_multi_drive(dk_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
/* Compact Flash */
at91_add_device_cf(&dk_cf_data);
/* I2C */
at91_add_device_i2c(dk_i2c_devices, ARRAY_SIZE(dk_i2c_devices));
/* SPI */
at91_add_device_spi(dk_spi_devices, ARRAY_SIZE(dk_spi_devices));
#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
/* DataFlash card */
at91_set_gpio_output(AT91_PIN_PB7, 0);
#else
/* MMC */
at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
at91_add_device_mmc(0, &dk_mmc_data);
#endif
/* NAND */
at91_add_device_nand(&dk_nand_data);
/* NOR Flash */
platform_device_register(&dk_flash);
/* LEDs */
at91_gpio_leds(dk_leds, ARRAY_SIZE(dk_leds));
/* SSC (to LM4549 audio codec) */
at91_add_device_ssc(AT91RM9200_ID_SSC1, ATMEL_SSC_TD | ATMEL_SSC_RX);
/* SSC (to SI3021 line interface) */
at91_add_device_ssc(AT91RM9200_ID_SSC2, ATMEL_SSC_TD | ATMEL_SSC_TK | ATMEL_SSC_RD | ATMEL_SSC_RF);
/* VGA */
dk_add_device_video();
}
static void __init afeb9260_board_init(void)
{
/* Serial */
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91SAM9260_ID_US0, 1,
ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR
| ATMEL_UART_DCD | ATMEL_UART_RI);
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2,
ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&afeb9260_usbh_data);
/* USB Device */
at91_add_device_udc(&afeb9260_udc_data);
/* SPI */
at91_add_device_spi(afeb9260_spi_devices,
ARRAY_SIZE(afeb9260_spi_devices));
/* NAND */
at91_add_device_nand(&afeb9260_nand_data);
/* Ethernet */
at91_add_device_eth(&afeb9260_macb_data);
/* Standard function's pin assignments are not
* appropriate for us and generic code provide
* no API to configure these pins any other way */
at91_set_B_periph(AT91_PIN_PA10, 0); /* ETX2 */
at91_set_B_periph(AT91_PIN_PA11, 0); /* ETX3 */
/* MMC */
at91_add_device_mci(0, &afeb9260_mci0_data);
/* I2C */
at91_add_device_i2c(afeb9260_i2c_devices,
ARRAY_SIZE(afeb9260_i2c_devices));
/* Audio */
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
/* IDE */
at91_add_device_cf(&afeb9260_cf_data);
}
static void __init ek_board_init(void)
{
/* Serial */
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* NAND */
ek_add_device_nand();
/* Ethernet */
ek_add_device_macb();
/* Regulators */
ek_add_regulators();
/* MMC */
ek_add_device_mmc();
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* LEDs */
ek_add_device_gpio_leds();
/* Push Buttons */
ek_add_device_buttons();
/* ADCs */
at91_add_device_adc(&ek_adc_data);
/* PCK0 provides MCLK to the WM8731 */
at91_set_B_periph(AT91_PIN_PC1, 0);
/* SSC (for WM8731) */
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
ek_add_device_audio();
}
static void __init ek_board_init(void)
{
/* Serial */
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
at91_add_device_serial();
if (cpu_is_at91sam9g10())
ek_lcdc_data.lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB;
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* NAND */
ek_add_device_nand();
/* DM9000 ethernet */
ek_add_device_dm9000();
/* spi0 and mmc/sd share the same PIO pins */
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* Touchscreen */
ek_add_device_ts();
/* SSC (to AT73C213) */
at73c213_set_clk(&at73c213_data);
at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX);
#else
/* MMC */
at91_add_device_mci(0, &mci0_data);
#endif
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
/* Push Buttons */
ek_add_device_buttons();
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
static void __init snapper9260_board_init(void)
{
at91_add_device_i2c(snapper9260_i2c_devices,
ARRAY_SIZE(snapper9260_i2c_devices));
snapper9260_i2c_isl1208.irq = gpio_to_irq(AT91_PIN_PA31);
i2c_register_board_info(0, &snapper9260_i2c_isl1208, 1);
/* Debug on ttyS0 */
at91_register_uart(0, 0, 0);
at91_register_uart(AT91SAM9260_ID_US0, 1,
ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_register_uart(AT91SAM9260_ID_US1, 2,
ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
at91_add_device_serial();
at91_add_device_usbh(&snapper9260_usbh_data);
at91_add_device_udc(&snapper9260_udc_data);
at91_add_device_eth(&snapper9260_macb_data);
at91_add_device_ssc(AT91SAM9260_ID_SSC, (ATMEL_SSC_TF | ATMEL_SSC_TK |
ATMEL_SSC_TD | ATMEL_SSC_RD));
snapper9260_add_device_nand();
}
static void __init ek_board_init(void)
{
/* Serial */
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* NAND */
ek_add_device_nand();
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* MMC */
at91_add_device_mci(0, &ek_mci0_data);
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* SSC (to AT73C213) */
at73c213_set_clk(&at73c213_data);
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
/* Push Buttons */
ek_add_device_buttons();
}