static int at91_do_twi_transfer(struct at91_twi_dev *dev)
{
int ret;
bool has_unre_flag = dev->pdata->has_unre_flag;
/*
* WARNING: the TXCOMP bit in the Status Register is NOT a clear on
* read flag but shows the state of the transmission at the time the
* Status Register is read. According to the programmer datasheet,
* TXCOMP is set when both holding register and internal shifter are
* empty and STOP condition has been sent.
* Consequently, we should enable NACK interrupt rather than TXCOMP to
* detect transmission failure.
*
* Besides, the TXCOMP bit is already set before the i2c transaction
* has been started. For read transactions, this bit is cleared when
* writing the START bit into the Control Register. So the
* corresponding interrupt can safely be enabled just after.
* However for write transactions managed by the CPU, we first write
* into THR, so TXCOMP is cleared. Then we can safely enable TXCOMP
* interrupt. If TXCOMP interrupt were enabled before writing into THR,
* the interrupt handler would be called immediately and the i2c command
* would be reported as completed.
* Also when a write transaction is managed by the DMA controller,
* enabling the TXCOMP interrupt in this function may lead to a race
* condition since we don't know whether the TXCOMP interrupt is enabled
* before or after the DMA has started to write into THR. So the TXCOMP
* interrupt is enabled later by at91_twi_write_data_dma_callback().
* Immediately after in that DMA callback, we still need to send the
* STOP condition manually writing the corresponding bit into the
* Control Register.
*/
dev_dbg(dev->dev, "transfer: %s %d bytes.\n",
(dev->msg->flags & I2C_M_RD) ? "read" : "write", dev->buf_len);
reinit_completion(&dev->cmd_complete);
dev->transfer_status = 0;
if (!dev->buf_len) {
at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_QUICK);
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP);
} else if (dev->msg->flags & I2C_M_RD) {
unsigned start_flags = AT91_TWI_START;
if (at91_twi_read(dev, AT91_TWI_SR) & AT91_TWI_RXRDY) {
dev_err(dev->dev, "RXRDY still set!");
at91_twi_read(dev, AT91_TWI_RHR);
}
/* if only one byte is to be read, immediately stop transfer */
if (dev->buf_len <= 1 && !(dev->msg->flags & I2C_M_RECV_LEN))
start_flags |= AT91_TWI_STOP;
at91_twi_write(dev, AT91_TWI_CR, start_flags);
/*
* When using dma, the last byte has to be read manually in
* order to not send the stop command too late and then
* to receive extra data. In practice, there are some issues
* if you use the dma to read n-1 bytes because of latency.
* Reading n-2 bytes with dma and the two last ones manually
* seems to be the best solution.
*/
if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) {
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_NACK);
at91_twi_read_data_dma(dev);
} else {
at91_twi_write(dev, AT91_TWI_IER,
AT91_TWI_TXCOMP |
AT91_TWI_NACK |
AT91_TWI_RXRDY);
}
} else {
if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) {
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_NACK);
at91_twi_write_data_dma(dev);
} else {
at91_twi_write_next_byte(dev);
at91_twi_write(dev, AT91_TWI_IER,
AT91_TWI_TXCOMP |
AT91_TWI_NACK |
AT91_TWI_TXRDY);
}
}
ret = wait_for_completion_timeout(&dev->cmd_complete,
dev->adapter.timeout);
if (ret == 0) {
dev_err(dev->dev, "controller timed out\n");
at91_init_twi_bus(dev);
ret = -ETIMEDOUT;
goto error;
}
if (dev->transfer_status & AT91_TWI_NACK) {
dev_dbg(dev->dev, "received nack\n");
ret = -EREMOTEIO;
goto error;
}
if (dev->transfer_status & AT91_TWI_OVRE) {
dev_err(dev->dev, "overrun while reading\n");
ret = -EIO;
goto error;
}
if (has_unre_flag && dev->transfer_status & AT91_TWI_UNRE) {
dev_err(dev->dev, "underrun while writing\n");
ret = -EIO;
goto error;
}
if (dev->recv_len_abort) {
dev_err(dev->dev, "invalid smbus block length recvd\n");
ret = -EPROTO;
goto error;
}
dev_dbg(dev->dev, "transfer complete\n");
return 0;
error:
at91_twi_dma_cleanup(dev);
return ret;
}
static int at91_do_twi_transfer(struct at91_twi_dev *dev)
{
int ret;
bool has_unre_flag = dev->pdata->has_unre_flag;
dev_dbg(dev->dev, "transfer: %s %d bytes.\n",
(dev->msg->flags & I2C_M_RD) ? "read" : "write", dev->buf_len);
INIT_COMPLETION(dev->cmd_complete);
dev->transfer_status = 0;
if (!dev->buf_len) {
at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_QUICK);
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP);
} else if (dev->msg->flags & I2C_M_RD) {
unsigned start_flags = AT91_TWI_START;
if (at91_twi_read(dev, AT91_TWI_SR) & AT91_TWI_RXRDY) {
dev_err(dev->dev, "RXRDY still set!");
at91_twi_read(dev, AT91_TWI_RHR);
}
/* if only one byte is to be read, immediately stop transfer */
if (dev->buf_len <= 1 && !(dev->msg->flags & I2C_M_RECV_LEN))
start_flags |= AT91_TWI_STOP;
at91_twi_write(dev, AT91_TWI_CR, start_flags);
/*
* When using dma, the last byte has to be read manually in
* order to not send the stop command too late and then
* to receive extra data. In practice, there are some issues
* if you use the dma to read n-1 bytes because of latency.
* Reading n-2 bytes with dma and the two last ones manually
* seems to be the best solution.
*/
if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) {
at91_twi_read_data_dma(dev);
/*
* It is important to enable TXCOMP irq here because
* doing it only when transferring the last two bytes
* will mask NACK errors since TXCOMP is set when a
* NACK occurs.
*/
at91_twi_write(dev, AT91_TWI_IER,
AT91_TWI_TXCOMP);
} else
at91_twi_write(dev, AT91_TWI_IER,
AT91_TWI_TXCOMP | AT91_TWI_RXRDY);
} else {
if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) {
at91_twi_write_data_dma(dev);
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP);
} else {
at91_twi_write_next_byte(dev);
at91_twi_write(dev, AT91_TWI_IER,
AT91_TWI_TXCOMP | AT91_TWI_TXRDY);
}
}
ret = wait_for_completion_interruptible_timeout(&dev->cmd_complete,
dev->adapter.timeout);
if (ret == 0) {
dev_err(dev->dev, "controller timed out\n");
at91_init_twi_bus(dev);
ret = -ETIMEDOUT;
goto error;
}
if (dev->transfer_status & AT91_TWI_NACK) {
dev_dbg(dev->dev, "received nack\n");
ret = -EREMOTEIO;
goto error;
}
if (dev->transfer_status & AT91_TWI_OVRE) {
dev_err(dev->dev, "overrun while reading\n");
ret = -EIO;
goto error;
}
if (has_unre_flag && dev->transfer_status & AT91_TWI_UNRE) {
dev_err(dev->dev, "underrun while writing\n");
ret = -EIO;
goto error;
}
dev_dbg(dev->dev, "transfer complete\n");
return 0;
error:
at91_twi_dma_cleanup(dev);
return ret;
}
static int at91_do_twi_transfer(struct at91_twi_dev *dev)
{
int ret;
unsigned long time_left;
bool has_unre_flag = dev->pdata->has_unre_flag;
bool has_alt_cmd = dev->pdata->has_alt_cmd;
/*
* WARNING: the TXCOMP bit in the Status Register is NOT a clear on
* read flag but shows the state of the transmission at the time the
* Status Register is read. According to the programmer datasheet,
* TXCOMP is set when both holding register and internal shifter are
* empty and STOP condition has been sent.
* Consequently, we should enable NACK interrupt rather than TXCOMP to
* detect transmission failure.
* Indeed let's take the case of an i2c write command using DMA.
* Whenever the slave doesn't acknowledge a byte, the LOCK, NACK and
* TXCOMP bits are set together into the Status Register.
* LOCK is a clear on write bit, which is set to prevent the DMA
* controller from sending new data on the i2c bus after a NACK
* condition has happened. Once locked, this i2c peripheral stops
* triggering the DMA controller for new data but it is more than
* likely that a new DMA transaction is already in progress, writing
* into the Transmit Holding Register. Since the peripheral is locked,
* these new data won't be sent to the i2c bus but they will remain
* into the Transmit Holding Register, so TXCOMP bit is cleared.
* Then when the interrupt handler is called, the Status Register is
* read: the TXCOMP bit is clear but NACK bit is still set. The driver
* manage the error properly, without waiting for timeout.
* This case can be reproduced easyly when writing into an at24 eeprom.
*
* Besides, the TXCOMP bit is already set before the i2c transaction
* has been started. For read transactions, this bit is cleared when
* writing the START bit into the Control Register. So the
* corresponding interrupt can safely be enabled just after.
* However for write transactions managed by the CPU, we first write
* into THR, so TXCOMP is cleared. Then we can safely enable TXCOMP
* interrupt. If TXCOMP interrupt were enabled before writing into THR,
* the interrupt handler would be called immediately and the i2c command
* would be reported as completed.
* Also when a write transaction is managed by the DMA controller,
* enabling the TXCOMP interrupt in this function may lead to a race
* condition since we don't know whether the TXCOMP interrupt is enabled
* before or after the DMA has started to write into THR. So the TXCOMP
* interrupt is enabled later by at91_twi_write_data_dma_callback().
* Immediately after in that DMA callback, if the alternative command
* mode is not used, we still need to send the STOP condition manually
* writing the corresponding bit into the Control Register.
*/
dev_dbg(dev->dev, "transfer: %s %zu bytes.\n",
(dev->msg->flags & I2C_M_RD) ? "read" : "write", dev->buf_len);
reinit_completion(&dev->cmd_complete);
dev->transfer_status = 0;
/* Clear pending interrupts, such as NACK. */
at91_twi_read(dev, AT91_TWI_SR);
if (dev->fifo_size) {
unsigned fifo_mr = at91_twi_read(dev, AT91_TWI_FMR);
/* Reset FIFO mode register */
fifo_mr &= ~(AT91_TWI_FMR_TXRDYM_MASK |
AT91_TWI_FMR_RXRDYM_MASK);
fifo_mr |= AT91_TWI_FMR_TXRDYM(AT91_TWI_ONE_DATA);
fifo_mr |= AT91_TWI_FMR_RXRDYM(AT91_TWI_ONE_DATA);
at91_twi_write(dev, AT91_TWI_FMR, fifo_mr);
/* Flush FIFOs */
at91_twi_write(dev, AT91_TWI_CR,
AT91_TWI_THRCLR | AT91_TWI_RHRCLR);
}
if (!dev->buf_len) {
at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_QUICK);
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP);
} else if (dev->msg->flags & I2C_M_RD) {
unsigned start_flags = AT91_TWI_START;
/* if only one byte is to be read, immediately stop transfer */
if (!dev->use_alt_cmd && dev->buf_len <= 1 &&
!(dev->msg->flags & I2C_M_RECV_LEN))
start_flags |= AT91_TWI_STOP;
at91_twi_write(dev, AT91_TWI_CR, start_flags);
/*
* When using dma without alternative command mode, the last
* byte has to be read manually in order to not send the stop
* command too late and then to receive extra data.
* In practice, there are some issues if you use the dma to
* read n-1 bytes because of latency.
* Reading n-2 bytes with dma and the two last ones manually
* seems to be the best solution.
*/
if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) {
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_NACK);
at91_twi_read_data_dma(dev);
} else {
at91_twi_write(dev, AT91_TWI_IER,
AT91_TWI_TXCOMP |
AT91_TWI_NACK |
AT91_TWI_RXRDY);
}
} else {
if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) {
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_NACK);
at91_twi_write_data_dma(dev);
} else {
at91_twi_write_next_byte(dev);
at91_twi_write(dev, AT91_TWI_IER,
AT91_TWI_TXCOMP |
AT91_TWI_NACK |
AT91_TWI_TXRDY);
}
}
time_left = wait_for_completion_timeout(&dev->cmd_complete,
dev->adapter.timeout);
if (time_left == 0) {
dev->transfer_status |= at91_twi_read(dev, AT91_TWI_SR);
dev_err(dev->dev, "controller timed out\n");
at91_init_twi_bus(dev);
ret = -ETIMEDOUT;
goto error;
}
if (dev->transfer_status & AT91_TWI_NACK) {
dev_dbg(dev->dev, "received nack\n");
ret = -EREMOTEIO;
goto error;
}
if (dev->transfer_status & AT91_TWI_OVRE) {
dev_err(dev->dev, "overrun while reading\n");
ret = -EIO;
goto error;
}
if (has_unre_flag && dev->transfer_status & AT91_TWI_UNRE) {
dev_err(dev->dev, "underrun while writing\n");
ret = -EIO;
goto error;
}
if ((has_alt_cmd || dev->fifo_size) &&
(dev->transfer_status & AT91_TWI_LOCK)) {
dev_err(dev->dev, "tx locked\n");
ret = -EIO;
goto error;
}
if (dev->recv_len_abort) {
dev_err(dev->dev, "invalid smbus block length recvd\n");
ret = -EPROTO;
goto error;
}
dev_dbg(dev->dev, "transfer complete\n");
return 0;
error:
/* first stop DMA transfer if still in progress */
at91_twi_dma_cleanup(dev);
/* then flush THR/FIFO and unlock TX if locked */
if ((has_alt_cmd || dev->fifo_size) &&
(dev->transfer_status & AT91_TWI_LOCK)) {
dev_dbg(dev->dev, "unlock tx\n");
at91_twi_write(dev, AT91_TWI_CR,
AT91_TWI_THRCLR | AT91_TWI_LOCKCLR);
}
return ret;
}
