/**
* usb_hcd_au1xxx_remove - shutdown processing for Au1xxx-based HCDs
* @dev: USB Host Controller being removed
* Context: !in_interrupt()
*
* Reverses the effect of usb_hcd_au1xxx_probe(), first invoking
* the HCD's stop() method. It is always called from a thread
* context, normally "rmmod", "apmd", or something similar.
*
*/
static void usb_ohci_au1xxx_remove(struct usb_hcd *hcd, struct platform_device *dev)
{
usb_remove_hcd(hcd);
au1xxx_stop_ohc(dev);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
}
/**
* usb_ohci_au1xxx_probe - initialize Au1xxx-based HCDs
* Context: !in_interrupt()
*
* Allocates basic resources for this USB host controller, and
* then invokes the start() method for the HCD associated with it
* through the hotplug entry's driver_data.
*
*/
static int usb_ohci_au1xxx_probe(const struct hc_driver *driver,
struct platform_device *dev)
{
int retval;
struct usb_hcd *hcd;
#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT)
/* Au1200 AB USB does not support coherent memory */
if (!(read_c0_prid() & 0xff)) {
pr_info("%s: this is chip revision AB !!\n",
dev->name);
pr_info("%s: update your board or re-configure the kernel\n",
dev->name);
return -ENODEV;
}
#endif
if (dev->resource[1].flags != IORESOURCE_IRQ) {
pr_debug("resource[1] is not IORESOURCE_IRQ\n");
return -ENOMEM;
}
hcd = usb_create_hcd(driver, &dev->dev, "au1xxx");
if (!hcd)
return -ENOMEM;
hcd->rsrc_start = dev->resource[0].start;
hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1;
if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
pr_debug("request_mem_region failed\n");
retval = -EBUSY;
goto err1;
}
hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
if (!hcd->regs) {
pr_debug("ioremap failed\n");
retval = -ENOMEM;
goto err2;
}
au1xxx_start_ohc(dev);
ohci_hcd_init(hcd_to_ohci(hcd));
retval = usb_add_hcd(hcd, dev->resource[1].start, IRQF_DISABLED | IRQF_SHARED);
if (retval == 0)
return retval;
au1xxx_stop_ohc(dev);
iounmap(hcd->regs);
err2:
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
err1:
usb_put_hcd(hcd);
return retval;
}
static int ohci_hcd_au1xxx_drv_remove(struct platform_device *pdev)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
usb_remove_hcd(hcd);
au1xxx_stop_ohc();
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
platform_set_drvdata(pdev, NULL);
return 0;
}
static int ohci_hcd_au1xxx_drv_suspend(struct platform_device *pdev,
pm_message_t message)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
struct ohci_hcd *ohci = hcd_to_ohci(hcd);
unsigned long flags;
int rc;
rc = 0;
/* Root hub was already suspended. Disable irq emission and
* mark HW unaccessible, bail out if RH has been resumed. Use
* the spinlock to properly synchronize with possible pending
* RH suspend or resume activity.
*
* This is still racy as hcd->state is manipulated outside of
* any locks =P But that will be a different fix.
*/
spin_lock_irqsave(&ohci->lock, flags);
if (hcd->state != HC_STATE_SUSPENDED) {
rc = -EINVAL;
goto bail;
}
ohci_writel(ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
(void)ohci_readl(ohci, &ohci->regs->intrdisable);
/* make sure snapshot being resumed re-enumerates everything */
if (message.event == PM_EVENT_PRETHAW)
ohci_usb_reset(ohci);
clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
au1xxx_stop_ohc();
bail:
spin_unlock_irqrestore(&ohci->lock, flags);
return rc;
}
