void board_init_f(ulong dummy)
{
/* Example code showing how to enable the debug UART on RK3188 */
#ifdef EARLY_UART
#include <asm/arch/grf_rk3188.h>
/* Enable early UART on the RK3188 */
#define GRF_BASE 0x20008000
struct rk3188_grf * const grf = (void *)GRF_BASE;
rk_clrsetreg(&grf->gpio1b_iomux,
GPIO1B1_MASK << GPIO1B1_SHIFT |
GPIO1B0_MASK << GPIO1B0_SHIFT,
GPIO1B1_UART2_SOUT << GPIO1B1_SHIFT |
GPIO1B0_UART2_SIN << GPIO1B0_SHIFT);
/*
* Debug UART can be used from here if required:
*
* debug_uart_init();
* printch('a');
* printhex8(0x1234);
* printascii("string");
*/
debug_uart_init();
printch('t');
printch('p');
printch('l');
printch('-');
printch(rk3188_num_entries + 1 + '0');
printch('\n');
#endif
rk3188_num_entries++;
if (rk3188_num_entries == 1) {
/*
* The original loader did some very basic integrity
* checking at this point, but the remaining few bytes
* could be used for any improvement making sense
* really early on.
*/
back_to_bootrom();
} else {
/*
* TPL part of the loader should now wait for us
* at offset 0xC00 in the sram. Should never return
* from there.
*/
jump_to_spl();
}
}
void spl_board_init(void)
{
struct udevice *pinctrl;
int ret;
ret = setup_led();
if (ret) {
debug("LED ret=%d\n", ret);
hang();
}
ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
if (ret) {
debug("%s: Cannot find pinctrl device\n", __func__);
goto err;
}
#ifdef CONFIG_SPL_MMC_SUPPORT
ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_SDCARD);
if (ret) {
debug("%s: Failed to set up SD card\n", __func__);
goto err;
}
ret = configure_emmc(pinctrl);
if (ret) {
debug("%s: Failed to set up eMMC\n", __func__);
goto err;
}
#endif
/* Enable debug UART */
ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_UART_DBG);
if (ret) {
debug("%s: Failed to set up console UART\n", __func__);
goto err;
}
preloader_console_init();
#if CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM)
back_to_bootrom(BROM_BOOT_NEXTSTAGE);
#endif
return;
err:
printf("spl_board_init: Error %d\n", ret);
/* No way to report error here */
hang();
}
void board_init_f(ulong dummy)
{
#ifdef EARLY_DEBUG
/*
* NOTE: sd card and debug uart use same iomux in rk3036,
* so if you enable uart,
* you can not boot from sdcard
*/
rk_clrsetreg(&grf->gpio1c_iomux,
GPIO1C3_MASK << GPIO1C3_SHIFT |
GPIO1C2_MASK << GPIO1C2_SHIFT,
GPIO1C3_UART2_SOUT << GPIO1C3_SHIFT |
GPIO1C2_UART2_SIN << GPIO1C2_SHIFT);
debug_uart_init();
#endif
rockchip_timer_init();
sdram_init();
/* return to maskrom */
back_to_bootrom();
}
void board_return_to_bootrom(void)
{
back_to_bootrom(BROM_BOOT_NEXTSTAGE);
}
void board_init_f(ulong dummy)
{
struct udevice *pinctrl, *dev;
struct rk3188_pmu *pmu;
int ret;
/* Example code showing how to enable the debug UART on RK3188 */
#ifdef EARLY_UART
#include <asm/arch/grf_rk3188.h>
/* Enable early UART on the RK3188 */
#define GRF_BASE 0x20008000
struct rk3188_grf * const grf = (void *)GRF_BASE;
rk_clrsetreg(&grf->gpio1b_iomux,
GPIO1B1_MASK << GPIO1B1_SHIFT |
GPIO1B0_MASK << GPIO1B0_SHIFT,
GPIO1B1_UART2_SOUT << GPIO1B1_SHIFT |
GPIO1B0_UART2_SIN << GPIO1B0_SHIFT);
/*
* Debug UART can be used from here if required:
*
* debug_uart_init();
* printch('a');
* printhex8(0x1234);
* printascii("string");
*/
debug_uart_init();
printch('s');
printch('p');
printch('l');
printch('\n');
#endif
ret = spl_early_init();
if (ret) {
debug("spl_early_init() failed: %d\n", ret);
hang();
}
rockchip_timer_init();
ret = rockchip_get_clk(&dev);
if (ret) {
debug("CLK init failed: %d\n", ret);
return;
}
/*
* Recover the bootrom's stackpointer.
* For whatever reason needs to run after rockchip_get_clk.
*/
pmu = syscon_get_first_range(ROCKCHIP_SYSCON_PMU);
if (IS_ERR(pmu))
error("pmu syscon returned %ld\n", PTR_ERR(pmu));
SAVE_SP_ADDR = readl(&pmu->sys_reg[2]);
ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
if (ret) {
debug("Pinctrl init failed: %d\n", ret);
return;
}
ret = uclass_get_device(UCLASS_RAM, 0, &dev);
if (ret) {
debug("DRAM init failed: %d\n", ret);
return;
}
setup_arm_clock();
#if defined(CONFIG_ROCKCHIP_SPL_BACK_TO_BROM) && !defined(CONFIG_SPL_BOARD_INIT)
back_to_bootrom();
#endif
}
void board_init_f(ulong dummy)
{
struct udevice *pinctrl;
struct udevice *dev;
int ret;
/* Example code showing how to enable the debug UART on RK3288 */
#include <asm/arch/grf_rk3288.h>
/* Enable early UART on the RK3288 */
#define GRF_BASE 0xff770000
struct rk3288_grf * const grf = (void *)GRF_BASE;
rk_clrsetreg(&grf->gpio7ch_iomux, GPIO7C7_MASK << GPIO7C7_SHIFT |
GPIO7C6_MASK << GPIO7C6_SHIFT,
GPIO7C7_UART2DBG_SOUT << GPIO7C7_SHIFT |
GPIO7C6_UART2DBG_SIN << GPIO7C6_SHIFT);
/*
* Debug UART can be used from here if required:
*
* debug_uart_init();
* printch('a');
* printhex8(0x1234);
* printascii("string");
*/
debug_uart_init();
debug("\nspl:debug uart enabled in %s\n", __func__);
ret = spl_early_init();
if (ret) {
debug("spl_early_init() failed: %d\n", ret);
hang();
}
rockchip_timer_init();
configure_l2ctlr();
ret = rockchip_get_clk(&dev);
if (ret) {
debug("CLK init failed: %d\n", ret);
return;
}
ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
if (ret) {
debug("Pinctrl init failed: %d\n", ret);
return;
}
#if !defined(CONFIG_SPL_OF_PLATDATA)
if (of_machine_is_compatible("phytec,rk3288-phycore-som")) {
ret = phycore_init();
if (ret) {
debug("Failed to set up phycore power settings: %d\n",
ret);
return;
}
}
#endif
#if !defined(CONFIG_SUPPORT_TPL)
debug("\nspl:init dram\n");
ret = uclass_get_device(UCLASS_RAM, 0, &dev);
if (ret) {
debug("DRAM init failed: %d\n", ret);
return;
}
#endif
#if CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM) && !defined(CONFIG_SPL_BOARD_INIT)
back_to_bootrom(BROM_BOOT_NEXTSTAGE);
#endif
}
void board_init_f(ulong dummy)
{
struct udevice *pinctrl, *dev;
int ret;
/* Example code showing how to enable the debug UART on RK3188 */
#ifdef EARLY_UART
#include <asm/arch/grf_rk3188.h>
/* Enable early UART on the RK3188 */
#define GRF_BASE 0x20008000
struct rk3188_grf * const grf = (void *)GRF_BASE;
rk_clrsetreg(&grf->gpio1b_iomux,
GPIO1B1_MASK << GPIO1B1_SHIFT |
GPIO1B0_MASK << GPIO1B0_SHIFT,
GPIO1B1_UART2_SOUT << GPIO1B1_SHIFT |
GPIO1B0_UART2_SIN << GPIO1B0_SHIFT);
/*
* Debug UART can be used from here if required:
*
* debug_uart_init();
* printch('a');
* printhex8(0x1234);
* printascii("string");
*/
debug_uart_init();
printch('s');
printch('p');
printch('l');
printch('\n');
#endif
ret = spl_early_init();
if (ret) {
debug("spl_early_init() failed: %d\n", ret);
hang();
}
ret = rockchip_get_clk(&dev);
if (ret) {
debug("CLK init failed: %d\n", ret);
return;
}
ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
if (ret) {
debug("Pinctrl init failed: %d\n", ret);
return;
}
ret = uclass_get_device(UCLASS_RAM, 0, &dev);
if (ret) {
debug("DRAM init failed: %d\n", ret);
return;
}
setup_arm_clock();
#if CONFIG_IS_ENABLED(ROCKCHIP_BACK_TO_BROM) && !defined(CONFIG_SPL_BOARD_INIT)
back_to_bootrom(BROM_BOOT_NEXTSTAGE);
#endif
}
