C++ (Cpp) board_detail示例

示例#1

文件： bdinfo.c 项目： Noltari/u-boot

int do_bdinfo(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
	bd_t *bd = gd->bd;

#ifdef DEBUG
	print_num("bd address",		(ulong)bd);
#endif
	print_bi_mem(bd);
	print_bi_flash(bd);
	print_num("sramstart",		bd->bi_sramstart);
	print_num("sramsize",		bd->bi_sramsize);
#if	defined(CONFIG_MPC8xx) || defined(CONFIG_E500)
	print_num("immr_base",		bd->bi_immr_base);
#endif
	print_num("bootflags",		bd->bi_bootflags);
#if defined(CONFIG_CPM2)
	print_mhz("vco",		bd->bi_vco);
	print_mhz("sccfreq",		bd->bi_sccfreq);
	print_mhz("brgfreq",		bd->bi_brgfreq);
#endif
	print_mhz("intfreq",		bd->bi_intfreq);
#if defined(CONFIG_CPM2)
	print_mhz("cpmfreq",		bd->bi_cpmfreq);
#endif
	print_mhz("busfreq",		bd->bi_busfreq);

#ifdef CONFIG_ENABLE_36BIT_PHYS
#ifdef CONFIG_PHYS_64BIT
	puts("addressing  = 36-bit\n");
#else
	puts("addressing  = 32-bit\n");
#endif
#endif

	print_eth_ip_addr();
	print_baudrate();
	print_num("relocaddr", gd->relocaddr);
	board_detail();
	return 0;
}

示例#2

文件： cmd_bdinfo.c 项目： 0s4l/u-boot-xlnx

int do_bdinfo(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
	bd_t *bd = gd->bd;

#ifdef DEBUG
	print_num("bd address",		(ulong)bd);
#endif
	print_num("memstart",		bd->bi_memstart);
	print_lnum("memsize",		bd->bi_memsize);
	print_num("flashstart",		bd->bi_flashstart);
	print_num("flashsize",		bd->bi_flashsize);
	print_num("flashoffset",	bd->bi_flashoffset);
	print_num("sramstart",		bd->bi_sramstart);
	print_num("sramsize",		bd->bi_sramsize);
#if	defined(CONFIG_5xx)  || defined(CONFIG_8xx) || \
	defined(CONFIG_8260) || defined(CONFIG_E500)
	print_num("immr_base",		bd->bi_immr_base);
#endif
	print_num("bootflags",		bd->bi_bootflags);
#if	defined(CONFIG_405EP) || \
	defined(CONFIG_405GP) || \
	defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
	defined(CONFIG_440GR) || defined(CONFIG_440GRX) || \
	defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
	defined(CONFIG_XILINX_405)
	print_mhz("procfreq",		bd->bi_procfreq);
	print_mhz("plb_busfreq",	bd->bi_plb_busfreq);
#if	defined(CONFIG_405EP) || defined(CONFIG_405GP) || \
	defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
	defined(CONFIG_440GR) || defined(CONFIG_440GRX) || \
	defined(CONFIG_440SPE) || defined(CONFIG_XILINX_405)
	print_mhz("pci_busfreq",	bd->bi_pci_busfreq);
#endif
#else	/* ! CONFIG_405GP, CONFIG_405EP, CONFIG_XILINX_405, CONFIG_440EP CONFIG_440GR */
#if defined(CONFIG_CPM2)
	print_mhz("vco",		bd->bi_vco);
	print_mhz("sccfreq",		bd->bi_sccfreq);
	print_mhz("brgfreq",		bd->bi_brgfreq);
#endif
	print_mhz("intfreq",		bd->bi_intfreq);
#if defined(CONFIG_CPM2)
	print_mhz("cpmfreq",		bd->bi_cpmfreq);
#endif
	print_mhz("busfreq",		bd->bi_busfreq);
#endif /* CONFIG_405GP, CONFIG_405EP, CONFIG_XILINX_405, CONFIG_440EP CONFIG_440GR */

#ifdef CONFIG_ENABLE_36BIT_PHYS
#ifdef CONFIG_PHYS_64BIT
	puts("addressing  = 36-bit\n");
#else
	puts("addressing  = 32-bit\n");
#endif
#endif

	print_eth(0);
#if defined(CONFIG_HAS_ETH1)
	print_eth(1);
#endif
#if defined(CONFIG_HAS_ETH2)
	print_eth(2);
#endif
#if defined(CONFIG_HAS_ETH3)
	print_eth(3);
#endif
#if defined(CONFIG_HAS_ETH4)
	print_eth(4);
#endif
#if defined(CONFIG_HAS_ETH5)
	print_eth(5);
#endif

#ifdef CONFIG_HERMES
	print_mhz("ethspeed",		bd->bi_ethspeed);
#endif
	printf("IP addr     = %s\n", getenv("ipaddr"));
	printf("baudrate    = %6u bps\n", bd->bi_baudrate);
	print_num("relocaddr", gd->relocaddr);
	board_detail();
	return 0;
}