void oneway_anchor_init () {
// Make sure the SPI speed is slow for this function
dw1000_spi_slow();
// Setup callbacks to this ANCHOR
dwt_setcallbacks(anchor_txcallback, anchor_rxcallback);
// Make sure the radio starts off
dwt_forcetrxoff();
// Set the anchor so it only receives data and ack packets
dwt_enableframefilter(DWT_FF_DATA_EN | DWT_FF_ACK_EN);
// // Set the ID and PAN ID for this anchor
uint8_t eui_array[8];
dw1000_read_eui(eui_array);
// dwt_seteui(eui_array);
// dwt_setpanid(POLYPOINT_PANID);
// Automatically go back to receive
dwt_setautorxreenable(TRUE);
// Don't use these
dwt_setdblrxbuffmode(FALSE);
dwt_setrxtimeout(FALSE);
// Load our EUI into the outgoing packet
dw1000_read_eui(pp_anc_final_pkt.ieee154_header_unicast.sourceAddr);
// Need a timer
if (_anchor_timer == NULL) {
_anchor_timer = timer_init();
}
// Init the PRNG for determining when to respond to the tag
raninit(&_prng_state, eui_array[0]<<8|eui_array[1]);
// Make SPI fast now that everything has been setup
dw1000_spi_fast();
// Reset our state because nothing should be in progress if we call init()
_state = ASTATE_IDLE;
}
dw1000_err_e dw1000_anchor_init () {
uint8_t eui_array[8];
// Make sure the radio starts off
dwt_forcetrxoff();
// Set the anchor so it only receives data and ack packets
dwt_enableframefilter(DWT_FF_DATA_EN | DWT_FF_ACK_EN);
// Set the ID and PAN ID for this anchor
dw1000_read_eui(eui_array);
dwt_seteui(eui_array);
dwt_setpanid(POLYPOINT_PANID);
// Automatically go back to receive
dwt_setautorxreenable(TRUE);
// Don't use these
dwt_setdblrxbuffmode(FALSE);
dwt_setrxtimeout(FALSE);
// Don't receive at first
dwt_rxenable(FALSE);
// Load our EUI into the outgoing packet
dw1000_read_eui(pp_anc_final_pkt.ieee154_header_unicast.sourceAddr);
// Need a timer
_ranging_broadcast_timer = timer_init();
// Init the PRNG for determining when to respond to the tag
raninit(&_prng_state, eui_array[0]<<8|eui_array[1]);
// Make SPI fast now that everything has been setup
dw1000_spi_fast();
return DW1000_NO_ERR;
}
int app_dw1000_init (
int HACK_role,
int HACK_EUI,
void (*txcallback)(const dwt_callback_data_t *),
void (*rxcallback)(const dwt_callback_data_t *)
) {
uint32_t devID;
int err;
// Start off DW1000 comms slow
REG(SSI0_BASE + SSI_CR1) = 0;
REG(SSI0_BASE + SSI_CPSR) = 8;
REG(SSI0_BASE + SSI_CR1) |= SSI_CR1_SSE;
// Reset the DW1000...for some reason
dw1000_reset();
// Make sure we can talk to the DW1000
devID = dwt_readdevid();
if (devID != DWT_DEVICE_ID) {
#ifdef DW_DEBUG
printf("Could not read Device ID from the DW1000\r\n");
printf("Possible the chip is asleep...\r\n");
#endif
return -1;
}
// Select which of the three antennas on the board to use
dw1000_choose_antenna(0);
// Init the dw1000 hardware
err = dwt_initialise(DWT_LOADUCODE |
DWT_LOADLDO |
DWT_LOADTXCONFIG |
DWT_LOADXTALTRIM);
if (err != DWT_SUCCESS) {
return -1;
}
// Setup interrupts
// Note: using auto rx re-enable so don't need to trigger on error frames
dwt_setinterrupt(DWT_INT_TFRS |
DWT_INT_RFCG |
DWT_INT_SFDT |
DWT_INT_RFTO |
DWT_INT_RPHE |
DWT_INT_RFCE |
DWT_INT_RFSL |
DWT_INT_RXPTO |
DWT_INT_SFDT, 1);
// Configure the callbacks from the dwt library
dwt_setcallbacks(txcallback, rxcallback);
// Set the parameters of ranging and channel and whatnot
global_ranging_config.chan = 2;
global_ranging_config.prf = DWT_PRF_64M;
global_ranging_config.txPreambLength = DWT_PLEN_64;//DWT_PLEN_4096
// global_ranging_config.txPreambLength = DWT_PLEN_256;
global_ranging_config.rxPAC = DWT_PAC8;
global_ranging_config.txCode = 9; // preamble code
global_ranging_config.rxCode = 9; // preamble code
global_ranging_config.nsSFD = 0;
global_ranging_config.dataRate = DWT_BR_6M8;
global_ranging_config.phrMode = DWT_PHRMODE_EXT; //Enable extended PHR mode (up to 1024-byte packets)
global_ranging_config.smartPowerEn = 1;
global_ranging_config.sfdTO = 64+8+1;//(1025 + 64 - 32);
dwt_configure(&global_ranging_config, 0);//(DWT_LOADANTDLY | DWT_LOADXTALTRIM));
dwt_setsmarttxpower(global_ranging_config.smartPowerEn);
// Configure TX power
{
global_tx_config.PGdly = pgDelay[global_ranging_config.chan];
global_tx_config.power = txPower[global_ranging_config.chan];
dwt_configuretxrf(&global_tx_config);
}
/* All constants same anyway
if(DW1000_ROLE_TYPE == TAG)
dwt_xtaltrim(xtaltrim[0]);
else
dwt_xtaltrim(xtaltrim[ANCHOR_EUI]);
*/
dwt_xtaltrim(xtaltrim[0]);
////TEST 1: XTAL trim calibration
//dwt_configcwmode(global_ranging_config.chan);
//dwt_xtaltrim(8);
//while(1);
//{
// //TEST 2: TX Power level calibration
// uint8_t msg[127] = "The quick brown fox jumps over the lazy dog. The quick brown fox jumps over the lazy dog. The quick brown fox jumps over the l";
// dwt_configcontinuousframemode(0x1000);
// dwt_writetxdata(127, (uint8 *) msg, 0) ;
// dwt_writetxfctrl(127, 0);
// dwt_starttx(DWT_START_TX_IMMEDIATE);
// while(1);
//}
// Configure the antenna delay settings
{
uint16_t antenna_delay;
//Antenna delay not really necessary if we're doing an end-to-end calibration
antenna_delay = 0;
dwt_setrxantennadelay(antenna_delay);
dwt_settxantennadelay(antenna_delay);
//global_tx_antenna_delay = antenna_delay;
//// Shift this over a bit for some reason. Who knows.
//// instance_common.c:508
//antenna_delay = dwt_readantennadelay(global_ranging_config.prf) >> 1;
//if (antenna_delay == 0) {
// printf("resetting antenna delay\r\n");
// // If it's not in the OTP, use a magic value from instance_calib.c
// antenna_delay = ((DWT_PRF_64M_RFDLY/ 2.0) * 1e-9 / DWT_TIME_UNITS);
// dwt_setrxantennadelay(antenna_delay);
// dwt_settxantennadelay(antenna_delay);
//}
//global_tx_antenna_delay = antenna_delay;
//printf("tx antenna delay: %u\r\n", antenna_delay);
}
// // Set the sleep delay. Not sure what this does actually.
// instancesettagsleepdelay(POLL_SLEEP_DELAY, BLINK_SLEEP_DELAY);
// Configure as either a tag or anchor
if (HACK_role == ANCHOR) {
uint8_t eui_array[8];
// Enable frame filtering
dwt_enableframefilter(DWT_FF_DATA_EN | DWT_FF_ACK_EN);
dw1000_populate_eui(eui_array, HACK_EUI);
dwt_seteui(eui_array);
dwt_setpanid(DW1000_PANID);
// We do want to enable auto RX
dwt_setautorxreenable(1);
// Let's do double buffering
dwt_setdblrxbuffmode(0);
// Disable RX timeout by setting to 0
dwt_setrxtimeout(0);
// Go for receiving
dwt_rxenable(0);
} else if (HACK_role == TAG) {
uint8_t eui_array[8];
// Allow data and ack frames
dwt_enableframefilter(DWT_FF_DATA_EN | DWT_FF_ACK_EN);
dw1000_populate_eui(eui_array, HACK_EUI);
dwt_seteui(eui_array);
dwt_setpanid(DW1000_PANID);
// Do this for the tag too
dwt_setautorxreenable(1);
dwt_setdblrxbuffmode(1);
dwt_enableautoack(5 /*ACK_RESPONSE_TIME*/);
// Configure sleep
{
int mode = DWT_LOADUCODE |
DWT_PRESRV_SLEEP |
DWT_CONFIG |
DWT_TANDV;
if (dwt_getldotune() != 0) {
// If we need to use LDO tune value from OTP kick it after sleep
mode |= DWT_LOADLDO;
}
// NOTE: on the EVK1000 the DEEPSLEEP is not actually putting the
// DW1000 into full DEEPSLEEP mode as XTAL is kept on
dwt_configuresleep(mode, DWT_WAKE_CS | DWT_SLP_EN);
}
}
// Make it fast
REG(SSI0_BASE + SSI_CR1) = 0;
REG(SSI0_BASE + SSI_CPSR) = 2;
REG(SSI0_BASE + SSI_CR1) |= SSI_CR1_SSE;
return 0;
}
void cph_deca_init_network(uint16_t panid, uint16_t shortid) {
// Configure network parameters
dwt_setpanid(panid);
dwt_setaddress16(shortid);
dwt_enableframefilter(DWT_FF_DATA_EN);
}
// -------------------------------------------------------------------------------------------------------------------
//
// the main instance state machine (for Tag instance mode only!)
//
// -------------------------------------------------------------------------------------------------------------------
//
int testapprun_tf(instance_data_t *inst, int message)
{
switch (inst->testAppState)
{
case TA_INIT :
// printf("TA_INIT") ;
switch (inst->mode)
{
case TAG:
{
int mode = 0;
dwt_enableframefilter(DWT_FF_DATA_EN | DWT_FF_ACK_EN); //allow data and ack frames;
inst->frameFilteringEnabled = 1 ;
dwt_setpanid(inst->panid);
dwt_seteui(inst->eui64);
inst->msg_f.panID[0] = (inst->panid) & 0xff;
inst->msg_f.panID[1] = inst->panid >> 8;
#if (DR_DISCOVERY == 1)
inst->mode = TAG_TDOA ;
inst->testAppState = TA_TXBLINK_WAIT_SEND;
memcpy(&inst->blinkmsg.tagID[0], &inst->eui64[0], BLINK_FRAME_SOURCE_ADDRESS);
#else
inst->testAppState = TA_TXPOLL_WAIT_SEND;
#endif
//can use RX auto re-enable when not logging/plotting errored frames
inst->rxautoreenable = 1;
dwt_setautorxreenable(inst->rxautoreenable); //not necessary to auto RX re-enable as the receiver is on for a short time (Tag knows when the response is coming)
//disable double buffer for a Tag - not needed....
dwt_setdblrxbuffmode(0); //enable/disable double RX buffer
//NOTE - Auto ACK only works if frame filtering is enabled!
dwt_enableautoack(ACK_RESPONSE_TIME); //wait for ACK_RESPONSE_TIME symbols (e.g. 5) before replying with the ACK
mode = (DWT_LOADUCODE|DWT_PRESRV_SLEEP|DWT_CONFIG|DWT_TANDV);
if((dwt_getldotune() != 0)) //if we need to use LDO tune value from OTP kick it after sleep
mode |= DWT_LOADLDO;
if(inst->configData.txPreambLength == DWT_PLEN_64) //if using 64 length preamble then use the corresponding OPSet
mode |= DWT_LOADOPSET;
//NOTE: on the EVK1000 the DEEPSLEEP is not actually putting the DW1000 into full DEEPSLEEP mode as XTAL is kept on
dwt_configuresleep(mode, DWT_WAKE_CS|DWT_SLP_EN); //configure the on wake parameters (upload the IC config settings)
}
break;
default:
break;
}
break; // end case TA_INIT
case TA_SLEEP_DONE :
{
event_data_t* dw_event = instance_getevent(20); //clear the event from the queue
// waiting for timout from application to wakup IC
if (dw_event->type != DWT_SIG_RX_TIMEOUT)
{
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT; //wait here for sleep timeout
break;
}
inst->done = INST_NOT_DONE_YET;
inst->instToSleep = 0;
inst->testAppState = inst->nextState;
inst->nextState = 0; //clear
inst->canprintinfo = 0;
//wake up from DEEP SLEEP
{
//wake up device from low power mode
//NOTE - in the ARM code just drop chip select for 200us
port_SPIx_clear_chip_select(); //CS low
instance_data[0].dwIDLE = 0; //reset
setup_DW1000RSTnIRQ(1); //enable RSTn IRQ
Sleep(1); //200 us to wake up then waits 5ms for DW1000 XTAL to stabilise
port_SPIx_set_chip_select(); //CS high
#if (DW_IDLE_CHK==1) //Wait (sleep) to give DW1000 time to get to IDLE state
Sleep(5);
//this is platform dependent - only program if DW EVK/EVB
dwt_setleds(1);
//MP bug - TX antenna delay needs reprogramming as it is not preserved
dwt_settxantennadelay(inst->txantennaDelay) ;
//set EUI as it will not be preserved unless the EUI is programmed and loaded from NVM
/*if((inst->mode == TAG) || (inst->mode == TAG_TDOA))
{
dwt_setpanid(inst->panid);
dwt_seteui(inst->eui64);
}*/
#elif (DW_IDLE_CHK==2) //Use RSTn pin to notify the micro that DW1000 is in IDLE
//need to poll to check when the DW1000 is in IDLE, the CPLL interrupt is not reliable
while(instance_data[0].dwIDLE == 0); //wait for DW1000 to go to IDLE state RSTn pin to go high
if(dwt_read32bitreg(0x0) != 0xDECA0130)
{
//error?
int x = 0;
}
setup_DW1000RSTnIRQ(0); //disable RSTn IRQ
#else
//need to poll to check when the DW1000 is in IDLE, the CPLL interrupt is not reliable
while(dwt_read32bitreg(0x0) != 0xDECA0130);
//Sleep(2);
#endif
dwt_entersleepaftertx(0);
dwt_setinterrupt(DWT_INT_TFRS, 1); //re-enable the TX/RX interrupts
}
}
break;
case TA_TXE_WAIT : //either go to sleep or proceed to TX a message
// printf("TA_TXE_WAIT") ;
//if we are scheduled to go to sleep before next sending then sleep first.
if(((inst->nextState == TA_TXPOLL_WAIT_SEND)
|| (inst->nextState == TA_TXBLINK_WAIT_SEND))
&& (inst->instToSleep) //go to sleep before sending the next poll
)
{
//the app should put chip into low power state and wake up in tagSleepTime_ms time...
//the app could go to *_IDLE state and wait for uP to wake it up...
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT_TO; //don't sleep here but kick off the TagTimeoutTimer (instancetimer)
inst->testAppState = TA_SLEEP_DONE;
if(inst->nextState == TA_TXBLINK_WAIT_SEND)
inst->canprintinfo = 1;
//put device into low power mode
dwt_entersleep(); //go to sleep
}
else //proceed to configuration and transmission of a frame
{
inst->testAppState = inst->nextState;
inst->nextState = 0; //clear
}
break ; // end case TA_TXE_WAIT
case TA_TXBLINK_WAIT_SEND :
{
//blink frames with IEEE EUI-64 tag ID
inst->blinkmsg.frameCtrl = 0xC5 ;
inst->blinkmsg.seqNum = inst->frame_sn++;
dwt_writetxdata((BLINK_FRAME_CRTL_AND_ADDRESS + FRAME_CRC), (uint8 *) (&inst->blinkmsg), 0) ; // write the frame data
dwt_writetxfctrl((BLINK_FRAME_CRTL_AND_ADDRESS + FRAME_CRC), 0);
//response will be sent after 500us (thus delay the receiver turn on by 290sym ~ 299us)
//use delayed rx on (wait4resp timer) - this value is applied when the TX frame is done/sent, so this value can be written after TX is started
dwt_setrxaftertxdelay(inst->rnginitW4Rdelay_sy); //units are ~us - wait for wait4respTIM before RX on (delay RX)
dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED); //always using immediate TX
dwt_setrxtimeout(inst->fwtoTimeB_sy); //units are us - wait for BLINKRX_FWTO_TIME after RX on before timing out
#if (DW_IDLE_CHK==2)
//this is platform dependent - only program if DW EVK/EVB
dwt_setleds(1);
//MP bug - TX antenna delay needs reprogramming as it is not preserved
dwt_settxantennadelay(inst->txantennaDelay) ;
#endif
inst->sentSN = inst->blinkmsg.seqNum;
inst->wait4ack = DWT_RESPONSE_EXPECTED; //Poll is coming soon after...
inst->instToSleep = 1;
inst->testAppState = TA_TX_WAIT_CONF ; // wait confirmation
inst->previousState = TA_TXBLINK_WAIT_SEND ;
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT; //will use RX FWTO to time out (set below)
}
break ; // end case TA_TXBLINK_WAIT_SEND
case TA_TXPOLL_WAIT_SEND :
{
#if (DR_DISCOVERY == 1)
//NOTE the anchor address is set after receiving the ranging initialisation message
inst->instToSleep = 1; //go to Sleep after this poll
#else
//set destination address
if(destaddress(inst))
{
break;
}
//copy anchor address to short message structure
inst->msg_f.destAddr[0] = inst->msg.destAddr[0];
inst->msg_f.destAddr[1] = inst->msg.destAddr[1];
#endif
inst->msg_f.messageData[FCODE] = RTLS_DEMO_MSG_TAG_POLLF;
inst->psduLength = TAG_POLL_F_MSG_LEN + FRAME_CRTL_AND_ADDRESS_S + FRAME_CRC + EXTRA_LENGTH;
//set frame type (0-2), SEC (3), Pending (4), ACK (5), PanIDcomp(6)
inst->msg_f.frameCtrl[0] = 0x41 /*PID comp*/;
//short address for both
inst->msg_f.frameCtrl[1] = 0x8 /*dest short address (16bits)*/ | 0x80 /*src short address (16bits)*/;
inst->msg_f.seqNum = inst->frame_sn++;
inst->wait4ack = DWT_RESPONSE_EXPECTED; //Response is coming after 275 us...
//500 -> 485, 800 -> 765
dwt_writetxfctrl(inst->psduLength, 0);
//if the response is expected there is a 1ms timeout to stop RX if no response (ACK or other frame) coming
dwt_setrxtimeout(inst->fwtoTime_sy); //units are us - wait for 215us after RX on
//use delayed rx on (wait4resp timer)
dwt_setrxaftertxdelay(inst->fixedReplyDelay_sy); //units are ~us - wait for wait4respTIM before RX on (delay RX)
dwt_writetxdata(inst->psduLength, (uint8 *) &inst->msg_f, 0) ; // write the poll frame data
//start TX of frame
dwt_starttx(DWT_START_TX_IMMEDIATE | inst->wait4ack);
#if (DW_IDLE_CHK==2)
//this is platform dependent - only program if DW EVK/EVB
dwt_setleds(1);
//MP bug - TX antenna delay needs reprogramming as it is not preserved
dwt_settxantennadelay(inst->txantennaDelay) ;
#endif
inst->sentSN = inst->msg_f.seqNum;
//write the final function code
inst->msg_f.messageData[FCODE] = RTLS_DEMO_MSG_TAG_FINALF;
//increment the sequence number for the final message
inst->msg_f.seqNum = inst->frame_sn;
inst->testAppState = TA_TX_WAIT_CONF ; // wait confirmation
inst->previousState = TA_TXPOLL_WAIT_SEND ;
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT; //will use RX FWTO to time out (set below)
inst->responseRxNum = 0;
}
break;
case TA_TX_WAIT_CONF :
//printf("TA_TX_WAIT_CONF") ;
{
//uint8 temp[5];
event_data_t* dw_event = instance_getevent(5); //get and clear this event
//NOTE: Can get the ACK before the TX confirm event for the frame requesting the ACK
//this happens because if polling the ISR the RX event will be processed 1st and then the TX event
//thus the reception of the ACK will be processed before the TX confirmation of the frame that requested it.
if(dw_event->type != DWT_SIG_TX_DONE) //wait for TX done confirmation
{
if(dw_event->type == DWT_SIG_RX_TIMEOUT) //got RX timeout - i.e. did not get the response (e.g. ACK)
{
//we need to wait for SIG_TX_DONE and then process the timeout and re-send the frame if needed
inst->gotTO = 1;
}
if(dw_event->type == SIG_RX_ACK)
{
inst->wait4ack = 0 ; //clear the flag as the ACK has been received
inst_processackmsg(inst, dw_event->msgu.rxackmsg.seqNum);
//printf("RX ACK in TA_TX_WAIT_CONF... wait for TX confirm before changing state\n");
}
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT;
break;
}
inst->done = INST_NOT_DONE_YET;
if(inst->previousState == TA_TXFINAL_WAIT_SEND) //tag will do immediate receive when waiting for report (as anchor sends it without delay)
{
#if (DR_DISCOVERY == 1)
//in Discovery mode anchor is not sending the report to tag go to sleep
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT_TO; //kick off the TagTimeoutTimer (instance timer) to initiate wakeup
inst->nextState = TA_TXPOLL_WAIT_SEND;
inst->testAppState = TA_TXE_WAIT; //we are going manually to sleep - change to TA_TXE_WAIT state
#else
//wait for report when non-Discovery mode
if(inst->wait4ack == 0)
dwt_rxenable(0) ; // turn receiver on,
#endif
break;
}
else if (inst->gotTO) //timeout
{
inst_processrxtimeout(inst);
inst->gotTO = 0;
}
else
{
if(inst->previousState == TA_TXPOLL_WAIT_SEND)
{
// write the final's frame control and address tx data (add CRC as the function will write length - 2)
dwt_writetxdata((FRAME_CRTL_AND_ADDRESS_S + 1 + FRAME_CRC), (uint8 *) &inst->msg_f, FINAL_MSG_OFFSET) ; // write the final frame data
dwt_entersleepaftertx(1);
dwt_setinterrupt(DWT_INT_TFRS, 0); //disable all the interrupts (wont be able to enter sleep if interrupts are pending)
inst->tagPollTxTime32l = dw_event->timeStamp32l;
inst->relpyAddress[0] = inst->msg_f.destAddr[0];
inst->relpyAddress[1] = inst->msg_f.destAddr[1];
inst->canprintinfo = 2;
}
if(inst->previousState == TA_TXRANGINGINIT_WAIT_SEND) //set frame control for the response message
{
dwt_writetxfctrl((ANCH_RESPONSE_F_MSG_LEN + FRAME_CRTL_AND_ADDRESS_S + FRAME_CRC + EXTRA_LENGTH), RESPONSE_MSG_OFFSET);
}
inst->testAppState = TA_RX_WAIT_DATA ; // wait for next frame
//turn RX on
if(inst->wait4ack == 0)
dwt_rxenable(0) ; // turn receiver on, immediate = 0/delayed = 1
inst->wait4ack = 0 ;
//dwt_readfromdevice(0x19, 0, 5, temp);
//sprintf((char*)&usbdata[20], "T2R%d %02x%02x%02x%02x%02x ", count, temp[4], temp[3], temp[2], temp[1], temp[0]);
//send_usbmessage(&usbdata[20], 16);
//count=0;
}
}
break ; // end case TA_TX_WAIT_CONF
case TA_RXE_WAIT :
//printf("TA_RXE_WAIT") ;
{
// - with "fast" ranging - we only get here after frame timeout...
//turn RX on
instancerxon(inst, 0, 0) ; // turn RX on, with/without delay
inst->testAppState = TA_RX_WAIT_DATA; // let this state handle it
// end case TA_RXE_WAIT, don't break, but fall through into the TA_RX_WAIT_DATA state to process it immediately.
if(message == 0) break;
}
case TA_RX_WAIT_DATA : // Wait RX data
//printf("TA_RX_WAIT_DATA") ;
switch (message)
{
case SIG_RX_BLINK :
{
instance_getevent(6); //get and clear this event
//else //not initiating ranging - continue to receive
{
inst->testAppState = TA_RX_WAIT_DATA ; // wait for next frame
//turn RX on
dwt_rxenable(0) ; // turn receiver on, immediate = 0/delayed = 1
inst->done = INST_NOT_DONE_YET;
}
}
break;
case SIG_RX_ACK :
{
event_data_t* dw_event = instance_getevent(7); //get and clear this event
inst_processackmsg(inst, dw_event->msgu.rxackmsg.seqNum);
//else we did not expect this ACK turn the RX on again
//only enable receiver when not using double buffering
inst->testAppState = TA_RX_WAIT_DATA ; // wait for next frame
//turn RX on
dwt_rxenable(0) ; // turn receiver on, immediate = 0/delayed = 1
inst->done = INST_NOT_DONE_YET;
}
break;
case DWT_SIG_RX_OKAY :
{
event_data_t* dw_event = instance_getevent(8); //get and clear this event
uint8 srcAddr[8] = {0,0,0,0,0,0,0,0};
int fcode = 0;
int fn_code = 0;
int srclen = 0;
int fctrladdr_len;
uint8 *messageData;
inst->stoptimer = 0; //clear the flag, as we have received a message
// 16 or 64 bit addresses
switch(dw_event->msgu.frame[1])
{
case 0xCC: //
memcpy(&srcAddr[0], &(dw_event->msgu.rxmsg_ll.sourceAddr[0]), ADDR_BYTE_SIZE_L);
fn_code = dw_event->msgu.rxmsg_ll.messageData[FCODE];
messageData = &dw_event->msgu.rxmsg_ll.messageData[0];
srclen = ADDR_BYTE_SIZE_L;
fctrladdr_len = FRAME_CRTL_AND_ADDRESS_L;
break;
case 0xC8: //
memcpy(&srcAddr[0], &(dw_event->msgu.rxmsg_sl.sourceAddr[0]), ADDR_BYTE_SIZE_L);
fn_code = dw_event->msgu.rxmsg_sl.messageData[FCODE];
messageData = &dw_event->msgu.rxmsg_sl.messageData[0];
srclen = ADDR_BYTE_SIZE_L;
fctrladdr_len = FRAME_CRTL_AND_ADDRESS_LS;
break;
case 0x8C: //
memcpy(&srcAddr[0], &(dw_event->msgu.rxmsg_ls.sourceAddr[0]), ADDR_BYTE_SIZE_S);
fn_code = dw_event->msgu.rxmsg_ls.messageData[FCODE];
messageData = &dw_event->msgu.rxmsg_ls.messageData[0];
srclen = ADDR_BYTE_SIZE_S;
fctrladdr_len = FRAME_CRTL_AND_ADDRESS_LS;
break;
case 0x88: //
memcpy(&srcAddr[0], &(dw_event->msgu.rxmsg_ss.sourceAddr[0]), ADDR_BYTE_SIZE_S);
fn_code = dw_event->msgu.rxmsg_ss.messageData[FCODE];
messageData = &dw_event->msgu.rxmsg_ss.messageData[0];
srclen = ADDR_BYTE_SIZE_S;
fctrladdr_len = FRAME_CRTL_AND_ADDRESS_S;
break;
}
if((inst->ackexpected) && (inst->ackTO)) //ACK frame was expected but we got a good frame - treat as ACK timeout
{
//printf("got good frame instead of ACK in DWT_SIG_RX_OKAY - pretend TO\n");
inst_processrxtimeout(inst);
message = 0; //clear the message as we have processed the event
}
else
{
inst->ackexpected = 0; //clear this as we got good frame (but as not using ACK TO) we prob missed the ACK - check if it has been addressed to us
fcode = fn_code; //tag has address filtering so if it received a frame it must be addressed to it
switch(fcode)
{
case RTLS_DEMO_MSG_RNG_INIT:
{
if(inst->mode == TAG_TDOA) //only start ranging with someone if not ranging already
{
//double delay = rxrngmsg->messageData[RES_T1] + (rxrngmsg->messageData[RES_T2] << 8); //in ms
inst->testAppState = TA_TXPOLL_WAIT_SEND ; // send next poll
//remember the anchor address
inst->msg_f.destAddr[0] = srcAddr[0];
inst->msg_f.destAddr[1] = srcAddr[1];
inst->msg_f.sourceAddr[0] = messageData[RES_R1];
inst->msg_f.sourceAddr[1] = messageData[RES_R1+1];
inst->tagShortAdd = (uint16)messageData[RES_R1] + ((uint16)messageData[RES_R2] << 8) ;
dwt_setaddress16(inst->tagShortAdd);
//instancesetreplydelay(delay); //
inst->mode = TAG ;
inst->rxTimeouts = 0; //reset timeout count
inst->instToSleep = 0; //don't go to sleep - start ranging instead and then sleep after 1 range is done
inst->done = INST_NOT_DONE_YET;
}
}
break; //RTLS_DEMO_MSG_RNG_INITF
case RTLS_DEMO_MSG_ANCH_RESPF:
{
#if (TWSYMRANGE == 1)
//need to write the delayed time before starting transmission
inst->delayedReplyTime32 = ((uint32)dw_event->timeStamp32h + (uint32)inst->fixedFastReplyDelay32h) ;
dwt_setdelayedtrxtime(inst->delayedReplyTime32) ;
dwt_writetxfctrl((TAG_FINAL_F_MSG_LEN + FRAME_CRTL_AND_ADDRESS_S + FRAME_CRC), FINAL_MSG_OFFSET);
if(dwt_starttx(DWT_START_TX_DELAYED))
{
//error - TX FAILED
// initiate the re-transmission
inst->testAppState = TA_TXE_WAIT ;
inst->nextState = TA_TXPOLL_WAIT_SEND;
dwt_entersleepaftertx(0);
inst->wait4ack = 0; //clear the flag as the TX has
inst->lateTX++;
break; //exit this switch case...
}
else
{
rtd_t rtd;
//calculate the difference between response rx and final tx
//here we just need to subtract the low 32 bits as the response delay is < 32bits (actually it is < 26 bits)
rtd.diffRmP = (uint32)dw_event->timeStamp32l - (uint32)inst->tagPollTxTime32l ;
//calculate difference between final tx and response rx
rtd.diffFmR = (uint32)inst->txantennaDelay + ((uint32)inst->fixedFastReplyDelay32h << 8) - ((uint32)dw_event->timeStamp32l & 0x1FF);
//write the rest of the message (the two response time differences (low 32 bits)
dwt_writetxdata((TAG_FINAL_F_MSG_LEN - 1 + FRAME_CRC), (uint8 *) &rtd, (FINAL_MSG_OFFSET+FRAME_CRTL_AND_ADDRESS_S+1)) ; // write the frame data
inst->sentSN = inst->msg_f.seqNum;
inst->previousState = TA_TXFINAL_WAIT_SEND;
//if Tag is not waiting for report - it will go to sleep automatically after the final is sent
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT_TO; //kick off the TagTimeoutTimer (instancetimer) to initiate wakeup
inst->testAppState = TA_SLEEP_DONE; //we are going automatically to sleep so no TX confirm interrupt (next state will be TA_SLEEP_DONE)
inst->canprintinfo = 1;
inst->txmsgcount ++;
inst->frame_sn++ ; //increment as final is sent
}
inst->respPSC = (dwt_read16bitoffsetreg(0x10, 2) >> 4);
inst->wait4ack = 0; //no response
inst->ackexpected = !ACK_REQUESTED ; //used to ignore unexpected ACK frames
//inst->rxu.anchorRespRxTime = inst->rxu.rxTimeStamp ; //Response's Rx time
inst->nextState = TA_TXPOLL_WAIT_SEND;
#else
if(inst->responseRxNum == 0) // this is first response
{
dwt_setrxtimeout(5000); //~5ms
//turn RX on
dwt_rxenable(0) ; // turn receiver on, immediate = 0/delayed = 1
inst->anchResp1RxTime32l = dw_event->timeStamp32l;
inst->responseRxNum++;
}
else // we have two responses and can calculate ToF
{
//the first response will be sent time X after reception of the poll, but as the tx time is snapped to 8ns
//we need to account for the low 9 bits of poll rx time in the RTD calculation
uint32 pollrxlowbits = (uint32)messageData[1] + (uint32)(messageData[2] << 8);
//RTD = (RxResp1 - TxPoll) - (RxResp2 - RxResp1)
//ToF = RTD/2 = RxResp1 - 0.5 * (TxPoll + RxResp2)
inst->tof32 = ((uint32)inst->anchResp1RxTime32l - (uint32)inst->tagPollTxTime32l + pollrxlowbits) - ((uint32)dw_event->timeStamp32l - (uint32)inst->anchResp1RxTime32l);
inst->tof32 <<= 1; //to make it compatible with reportTOF() which expects ToF*4
reportTOF_f(inst);
inst->newrange = 1;
inst->testAppState = TA_TXE_WAIT ;
inst->nextState = TA_TXPOLL_WAIT_SEND;
}
#endif
}
break; //RTLS_DEMO_MSG_ANCH_RESPF
case RTLS_DEMO_MSG_ANCH_TOFRF:
{
inst->tof32 = messageData[TOFR];
inst->tof32 += (uint32)messageData[TOFR+1] << 8;
inst->tof32 += (uint32)messageData[TOFR+2] << 16;
inst->tof32 += (uint32)messageData[TOFR+3] << 24;
if(dw_event->msgu.rxmsg_ss.seqNum != inst->lastReportSN)
{
reportTOF_f(inst);
inst->newrange = 1;
inst->lastReportSN = dw_event->msgu.rxmsg_ss.seqNum;
inst->newrangetagaddress = srcAddr[0] + ((uint16) srcAddr[1] << 8);
inst->newrangeancaddress = inst->eui64[0] + ((uint16) inst->eui64[1] << 8);
}
inst->testAppState = TA_TXE_WAIT;
inst->nextState = TA_TXPOLL_WAIT_SEND ; // send next poll
}
break; //RTLS_DEMO_MSG_ANCH_TOFRF
default:
{
//only enable receiver when not using double buffering
inst->testAppState = TA_RX_WAIT_DATA ; // wait for next frame
//turn RX on
dwt_rxenable(0) ; // turn receiver on, immediate = 0/delayed = 1
}
break;
} //end switch (rxmsg->functionCode)
if(dw_event->msgu.frame[0] & 0x20)
{
//as we only pass the received frame with the ACK request bit set after the ACK has been sent
instance_getevent(9); //get and clear the ACK sent event
}
}
}
break ;
case DWT_SIG_RX_TIMEOUT :
//printf("PD_DATA_TIMEOUT") ;
instance_getevent(26); //get and clear this event
inst_processrxtimeout(inst);
message = 0; //clear the message as we have processed the event
break ;
case DWT_SIG_TX_AA_DONE: //ignore this event - just process the rx frame that was received before the ACK response
case 0: //no event - wait in receive...
{
//stay in Rx (fall-through from above state)
//if(DWT_SIG_TX_AA_DONE == message) printf("Got SIG_TX_AA_DONE in RX wait - ignore\n");
if(inst->done == INST_NOT_DONE_YET) inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT;
}
break;
default :
{
//printf("\nERROR - Unexpected message %d ??\n", message) ;
//assert(0) ; // Unexpected Primitive what is going on ?
}
break ;
}
break ; // end case TA_RX_WAIT_DATA
default:
//printf("\nERROR - invalid state %d - what is going on??\n", inst->testAppState) ;
break;
} // end switch on testAppState
return inst->done;
} // end testapprun()
// -------------------------------------------------------------------------------------------------------------------
//
// the main instance state machine (all the instance modes Tag, Anchor or Listener use the same statemachine....)
//
// -------------------------------------------------------------------------------------------------------------------
//
int testapprun(instance_data_t *inst, int message)
{
switch (inst->testAppState)
{
case TA_INIT :
#if defined(DEBUG)
printf("TA_INIT") ;
#endif
switch (inst->mode)
{
case TAG:
{
uint16 sleep_mode = 0;
dwt_enableframefilter(DWT_FF_DATA_EN | DWT_FF_ACK_EN); //allow data, ack frames;
dwt_setpanid(inst->panID);
memcpy(inst->eui64, &inst->instanceAddress16, ADDR_BYTE_SIZE_S);
dwt_seteui(inst->eui64);
//set source address
inst->newRangeTagAddress = inst->instanceAddress16 ;
dwt_setaddress16(inst->instanceAddress16);
//Start off by Sleeping 1st -> set instToSleep to TRUE
inst->nextState = TA_TXPOLL_WAIT_SEND;
inst->testAppState = TA_TXE_WAIT;
inst->instToSleep = TRUE ;
inst->rangeNum = 0;
inst->tagSleepCorrection = 0;
sleep_mode = (DWT_LOADUCODE|DWT_PRESRV_SLEEP|DWT_CONFIG|DWT_TANDV);
if((dwt_getldotune() != 0)) //if we need to use LDO tune value from OTP kick it after sleep
sleep_mode |= DWT_LOADLDO;
if(inst->configData.txPreambLength == DWT_PLEN_64) //if using 64 length preamble then use the corresponding OPSet
sleep_mode |= DWT_LOADOPSET;
#if (DEEP_SLEEP == 1)
dwt_configuresleep(sleep_mode, DWT_WAKE_WK|DWT_WAKE_CS|DWT_SLP_EN); //configure the on wake parameters (upload the IC config settings)
#endif
instanceconfigframeheader16(inst);
inst->instanceWakeTime = portGetTickCount();
}
break;
case ANCHOR:
{
memcpy(inst->eui64, &inst->instanceAddress16, ADDR_BYTE_SIZE_S);
dwt_seteui(inst->eui64);
dwt_setpanid(inst->panID);
//set source address
inst->shortAdd_idx = (inst->instanceAddress16 & 0x3) ;
dwt_setaddress16(inst->instanceAddress16);
//if address = 0x8000
if(inst->instanceAddress16 == GATEWAY_ANCHOR_ADDR)
{
inst->gatewayAnchor = TRUE;
}
dwt_enableframefilter(DWT_FF_NOTYPE_EN); //allow data, ack frames;
// First time anchor listens we don't do a delayed RX
dwt_setrxaftertxdelay(0);
//change to next state - wait to receive a message
inst->testAppState = TA_RXE_WAIT ;
dwt_setrxtimeout(0);
dwt_setpreambledetecttimeout(0);
instanceconfigframeheader16(inst);
}
break;
case LISTENER:
{
dwt_enableframefilter(DWT_FF_NOTYPE_EN); //disable frame filtering
dwt_setrxaftertxdelay(0); //no delay of turning on of RX
dwt_setrxtimeout(0);
dwt_setpreambledetecttimeout(0);
//change to next state - wait to receive a message
inst->testAppState = TA_RXE_WAIT ;
}
break ; // end case TA_INIT
default:
break;
}
break; // end case TA_INIT
case TA_SLEEP_DONE :
{
event_data_t* dw_event = instance_getevent(10); //clear the event from the queue
// waiting for timout from application to wakup IC
if (dw_event->type != DWT_SIG_RX_TIMEOUT)
{
// if no pause and no wake-up timeout continu waiting for the sleep to be done.
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT; //wait here for sleep timeout
break;
}
inst->done = INST_NOT_DONE_YET;
inst->instToSleep = FALSE ;
inst->testAppState = inst->nextState;
inst->nextState = 0; //clear
inst->instanceWakeTime = portGetTickCount(); // Record the time count when we wake-up
#if (DEEP_SLEEP == 1)
{
uint32 x = 0;
//wake up device from low power mode
//NOTE - in the ARM code just drop chip select for 200us
//led_on(LED_PC9);
port_SPIx_clear_chip_select(); //CS low
instance_data[0].dwIDLE = 0; //reset DW1000 IDLE flag
setup_DW1000RSTnIRQ(1); //enable RSTn IRQ
Sleep(2); //200 us to wake up - need 2 as Sleep(1) is ~ 175 us
//then wait 5ms for DW1000 XTAL to stabilise - instead of wait we wait for RSTn to go high
//Sleep(5);
Sleep(83);
//need to poll to check when the DW1000 is in IDLE, the CPLL interrupt is not reliable
//when RSTn goes high the DW1000 is in INIT, it will enter IDLE after PLL lock (in 5 us)
/*while(instance_data[0].dwIDLE == 0) // this variable will be sent in the IRQ (process_dwRSTn_irq)
{
//wait for DW1000 to go to IDLE state RSTn pin to go high
x++;
}*/
setup_DW1000RSTnIRQ(0); //disable RSTn IRQ
port_SPIx_set_chip_select(); //CS high
//!!! NOTE it takes ~35us for the DW1000 to download AON and lock the PLL and be in IDLE state
//do some dummy reads of the dev ID register to make sure DW1000 is in IDLE before setting LEDs
x = dwt_readdevid(); //dummy read... need to wait for 5 us to exit INIT state (5 SPI bytes @ ~18 MHz)
x = dwt_readdevid(); //dummy read... need to wait for 5 us to exit INIT state (5 SPI bytes @ ~18 MHz)
x = dwt_readdevid(); //dummy read... need to wait for 5 us to exit INIT state (5 SPI bytes @ ~18 MHz)
x = dwt_readdevid(); //dummy read... need to wait for 5 us to exit INIT state (5 SPI bytes @ ~18 MHz)
x = dwt_readdevid(); //dummy read... need to wait for 5 us to exit INIT state (5 SPI bytes @ ~18 MHz)
/*if(x != DWT_DEVICE_ID)
{
x = dwt_readdevid(); //dummy read... need to wait for 5 us to exit INIT state (5 SPI bytes @ ~18 MHz)
}*/
//led_off(LED_PC9);
//this is platform dependent - only program if DW EVK/EVB
dwt_setleds(1);
//MP bug - TX antenna delay needs reprogramming as it is not preserved (only RX)
dwt_settxantennadelay(inst->txAntennaDelay) ;
//set EUI as it will not be preserved unless the EUI is programmed and loaded from NVM
dwt_seteui(inst->eui64);
}
#else
Sleep(3); //to approximate match the time spent in the #if above
#endif
instancesetantennadelays(); //this will update the antenna delay if it has changed
instancesettxpower(); //configure TX power if it has changed
}
break;
case TA_TXE_WAIT : //either go to sleep or proceed to TX a message
#if defined(DEBUG)
printf("TA_TXE_WAIT\n") ;
#endif
//if we are scheduled to go to sleep before next transmission then sleep first.
if((inst->nextState == TA_TXPOLL_WAIT_SEND)
&& (inst->instToSleep) //go to sleep before sending the next poll/ starting new ranging exchange
)
{
inst->rangeNum++; //increment the range number before going to sleep
//the app should put chip into low power state and wake up after tagSleepTime_ms time...
//the app could go to *_IDLE state and wait for uP to wake it up...
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT_TO; //don't sleep here but kick off the Sleep timer countdown
inst->testAppState = TA_SLEEP_DONE;
{
#if (DEEP_SLEEP == 1)
//put device into low power mode
dwt_entersleep(); //go to sleep
#endif
//DW1000 gone to sleep - report the received range
inst->newRange = instance_calcranges(&inst->tofArray[0], MAX_ANCHOR_LIST_SIZE, TOF_REPORT_T2A, &inst->rxResponseMask);
inst->rxResponseMaskReport = inst->rxResponseMask;
inst->rxResponseMask = 0;
inst->newRangeTime = portGetTickCount() ;
}
}
else //proceed to configuration and transmission of a frame
{
inst->testAppState = inst->nextState;
inst->nextState = 0; //clear
}
break ; // end case TA_TXE_WAIT
case TA_TXPOLL_WAIT_SEND :
{
#if defined(DEBUG)
printf("TA_TXPOLL_WAIT_SEND\n") ;
#endif
inst->msg_f.messageData[POLL_RNUM] = (inst->mode == TAG) ? inst->rangeNum : inst->rangeNumAnc; //copy new range number
inst->msg_f.messageData[FCODE] = (inst->mode == TAG) ? RTLS_DEMO_MSG_TAG_POLL : RTLS_DEMO_MSG_ANCH_POLL; //message function code (specifies if message is a poll, response or other...)
inst->psduLength = (TAG_POLL_MSG_LEN + FRAME_CRTL_AND_ADDRESS_S + FRAME_CRC);
inst->msg_f.seqNum = inst->frameSN++; //copy sequence number and then increment
inst->msg_f.sourceAddr[0] = inst->eui64[0]; //copy the address
inst->msg_f.sourceAddr[1] = inst->eui64[1]; //copy the address
inst->msg_f.destAddr[0] = 0xff; //set the destination address (broadcast == 0xffff)
inst->msg_f.destAddr[1] = 0xff; //set the destination address (broadcast == 0xffff)
dwt_writetxdata(inst->psduLength, (uint8 *) &inst->msg_f, 0) ; // write the frame data
//set the delayed rx on time (the response message will be sent after this delay (from A0))
dwt_setrxaftertxdelay((uint32)RX_RESPONSE1_TURNAROUND); //units are 1.0256us - wait for wait4respTIM before RX on (delay RX)
if(inst->mode == TAG)
{
inst->rxResps[inst->rangeNum] = 0; //reset the number of received responses
inst->responseTO = MAX_ANCHOR_LIST_SIZE; //expecting 4 responses
dwt_setrxtimeout((uint16)inst->fwtoTime_sy * MAX_ANCHOR_LIST_SIZE); //configure the RX FWTO
}
else
{
inst->rxResps[inst->rangeNumAnc] = 0; //reset number of responses
inst->responseTO = NUM_EXPECTED_RESPONSES_ANC0; //2 responses A1, A2
dwt_setrxtimeout((uint16)inst->fwtoTime_sy * (NUM_EXPECTED_RESPONSES_ANC0)); //units are
}
inst->rxResponseMask = 0; //reset/clear the mask of received responses when tx poll
inst->rxResponseMaskAnc = 0;
inst->wait4ack = DWT_RESPONSE_EXPECTED; //response is expected - automatically enable the receiver
dwt_writetxfctrl(inst->psduLength, 0); //write frame control
dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED); //transmit the frame
inst->testAppState = TA_TX_WAIT_CONF ; // wait confirmation
inst->previousState = TA_TXPOLL_WAIT_SEND ;
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT; //will use RX FWTO to time out (set above)
}
break;
case TA_TXFINAL_WAIT_SEND :
{
//the final has the same range number as the poll (part of the same ranging exchange)
inst->msg_f.messageData[POLL_RNUM] = (inst->mode == TAG) ? inst->rangeNum : inst->rangeNumAnc;
//the mask is sent so the anchors know whether the response RX time is valid
inst->msg_f.messageData[VRESP] = (inst->mode == TAG) ? inst->rxResponseMask : inst->rxResponseMaskAnc;
inst->msg_f.messageData[FCODE] = (inst->mode == TAG) ? RTLS_DEMO_MSG_TAG_FINAL : RTLS_DEMO_MSG_ANCH_FINAL; //message function code (specifies if message is a poll, response or other...)
inst->psduLength = (TAG_FINAL_MSG_LEN + FRAME_CRTL_AND_ADDRESS_S + FRAME_CRC);
inst->msg_f.seqNum = inst->frameSN++;
dwt_writetxdata(inst->psduLength, (uint8 *) &inst->msg_f, 0) ; // write the frame data
inst->wait4ack = 0; //clear the flag not using wait for response as this message ends the ranging exchange
if(instancesenddlypacket(inst, DWT_START_TX_DELAYED))
{
// initiate the re-transmission
if(inst->mode == TAG)
{
inst->testAppState = TA_TXE_WAIT ; //go to TA_TXE_WAIT first to check if it's sleep time
inst->nextState = TA_TXPOLL_WAIT_SEND ;
}
else
{
//A0 - failed to send Final
//A1 - failed to send Final
//go back to RX and behave as anchor
instance_backtoanchor(inst);
}
break; //exit this switch case...
}
else
{
inst->testAppState = TA_TX_WAIT_CONF; // wait confirmation
inst->previousState = TA_TXFINAL_WAIT_SEND;
}
if(inst->mode == TAG)
{
inst->instToSleep = TRUE ;
}
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT; //will use RX FWTO to time out (set above)
}
break;
case TA_TX_WAIT_CONF :
#if defined(DEBUG)
printf("TA_TX_WAIT_CONF %d m%d states %08x %08x\n", inst->previousState, message, dwt_read32bitreg(0x19), dwt_read32bitreg(0x0f)) ;
#endif
{
event_data_t* dw_event = instance_getevent(11); //get and clear this event
//NOTE: Can get the ACK before the TX confirm event for the frame requesting the ACK
//this happens because if polling the ISR the RX event will be processed 1st and then the TX event
//thus the reception of the ACK will be processed before the TX confirmation of the frame that requested it.
if(dw_event->type != DWT_SIG_TX_DONE) //wait for TX done confirmation
{
if(dw_event->type != 0)
{
if(dw_event->type == DWT_SIG_RX_TIMEOUT) //got RX timeout - i.e. did not get the response (e.g. ACK)
{
#if defined(DEBUG)
printf("RX timeout in TA_TX_WAIT_CONF (%d)\n", inst->previousState);
#endif
//we need to wait for SIG_TX_DONE and then process the timeout and re-send the frame if needed
inst->gotTO = 1;
}
else
{
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT;
}
}
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT;
break;
}
inst->done = INST_NOT_DONE_YET;
if(inst->previousState == TA_TXFINAL_WAIT_SEND)
{
if(inst->mode == TAG)
{
inst->testAppState = TA_TXE_WAIT ;
inst->nextState = TA_TXPOLL_WAIT_SEND ;
break;
}
else
{
instance_backtoanchor(inst);
}
}
else if (inst->gotTO == 1) //timeout
{
#if defined(DEBUG)
printf("got TO in TA_TX_WAIT_CONF\n");
#endif
inst_processrxtimeout(inst);
inst->gotTO = 0;
inst->wait4ack = 0 ; //clear this
break;
}
else
{
inst->txu.txTimeStamp = dw_event->timeStamp;
if(inst->previousState == TA_TXPOLL_WAIT_SEND)
{
uint64 tagCalculatedFinalTxTime ;
// Embed into Final message: 40-bit pollTXTime, 40-bit respRxTime, 40-bit finalTxTime
if(inst->mode == TAG)
{
tagCalculatedFinalTxTime = (inst->txu.txTimeStamp + inst->pollTx2FinalTxDelay) & MASK_TXDTS;
}
else //for anchor make the final half the delay ..... (this is ok, as A0 awaits 2 responses)
{
tagCalculatedFinalTxTime = (inst->txu.txTimeStamp + inst->pollTx2FinalTxDelayAnc) & MASK_TXDTS;
}
inst->delayedReplyTime = tagCalculatedFinalTxTime >> 8; //high 32-bits
// Calculate Time Final message will be sent and write this field of Final message
// Sending time will be delayedReplyTime, snapped to ~125MHz or ~250MHz boundary by
// zeroing its low 9 bits, and then having the TX antenna delay added
// getting antenna delay from the device and add it to the Calculated TX Time
tagCalculatedFinalTxTime = tagCalculatedFinalTxTime + inst->txAntennaDelay;
tagCalculatedFinalTxTime &= MASK_40BIT;
// Write Calculated TX time field of Final message
memcpy(&(inst->msg_f.messageData[FTXT]), (uint8 *)&tagCalculatedFinalTxTime, 5);
// Write Poll TX time field of Final message
memcpy(&(inst->msg_f.messageData[PTXT]), (uint8 *)&inst->txu.tagPollTxTime, 5);
//change the w4r for the second and remaining anchors to 50 us
//dwt_setrxaftertxdelay((uint32)RX_RESPONSEX_TURNAROUND); //units are 1.0256us - wait for wait4respTIM before RX on (delay RX)
}
if(inst->previousState == TA_TXRESPONSE_SENT_TORX)
{
inst->previousState = TA_TXRESPONSE_WAIT_SEND ;
}
inst->testAppState = TA_RXE_WAIT ; // After sending, tag expects response/report, anchor waits to receive a final/new poll
message = 0;
//fall into the next case (turn on the RX)
}
}
//break ; // end case TA_TX_WAIT_CONF
case TA_RXE_WAIT :
#if defined(DEBUG)
printf("TA_RXE_WAIT\n") ;
#endif
{
if(inst->wait4ack == 0) //if this is set the RX will turn on automatically after TX
{
//turn RX on
dwt_rxenable(DWT_START_RX_IMMEDIATE) ; // turn RX on, without delay
}
else
{
inst->wait4ack = 0 ; //clear the flag, the next time we want to turn the RX on it might not be auto
}
if (inst->mode != LISTENER)
{
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT; //using RX FWTO
}
inst->testAppState = TA_RX_WAIT_DATA; // let this state handle it
// end case TA_RXE_WAIT, don't break, but fall through into the TA_RX_WAIT_DATA state to process it immediately.
if(message == 0) break;
}
case TA_RX_WAIT_DATA : // Wait RX data
#if defined(DEBUG)
printf("TA_RX_WAIT_DATA %d\n", message) ;
#endif
switch (message)
{
//if we have received a DWT_SIG_RX_OKAY event - this means that the message is IEEE data type - need to check frame control to know which addressing mode is used
case DWT_SIG_RX_OKAY :
{
event_data_t* dw_event = instance_getevent(15); //get and clear this event
uint8 srcAddr[8] = {0,0,0,0,0,0,0,0};
uint8 dstAddr[8] = {0,0,0,0,0,0,0,0};
int fcode = 0;
int fn_code = 0;
//int srclen = 0;
//int fctrladdr_len;
uint8 tof_idx = 0;
uint8 *messageData;
inst->stopTimer = 0; //clear the flag, as we have received a message
// handle 16 and 64 bit source and destination addresses
switch(dw_event->msgu.frame[1] & 0xCC)
{
case 0xCC: //
memcpy(&srcAddr[0], &(dw_event->msgu.rxmsg_ll.sourceAddr[0]), ADDR_BYTE_SIZE_L);
memcpy(&dstAddr[0], &(dw_event->msgu.rxmsg_ll.destAddr[0]), ADDR_BYTE_SIZE_L);
fn_code = dw_event->msgu.rxmsg_ll.messageData[FCODE];
messageData = &dw_event->msgu.rxmsg_ll.messageData[0];
//srclen = ADDR_BYTE_SIZE_L;
//fctrladdr_len = FRAME_CRTL_AND_ADDRESS_L;
break;
case 0xC8: //
memcpy(&srcAddr[0], &(dw_event->msgu.rxmsg_sl.sourceAddr[0]), ADDR_BYTE_SIZE_L);
memcpy(&dstAddr[0], &(dw_event->msgu.rxmsg_sl.destAddr[0]), ADDR_BYTE_SIZE_S);
fn_code = dw_event->msgu.rxmsg_sl.messageData[FCODE];
messageData = &dw_event->msgu.rxmsg_sl.messageData[0];
//srclen = ADDR_BYTE_SIZE_L;
//fctrladdr_len = FRAME_CRTL_AND_ADDRESS_LS;
break;
case 0x8C: //
memcpy(&srcAddr[0], &(dw_event->msgu.rxmsg_ls.sourceAddr[0]), ADDR_BYTE_SIZE_S);
memcpy(&dstAddr[0], &(dw_event->msgu.rxmsg_ls.destAddr[0]), ADDR_BYTE_SIZE_L);
fn_code = dw_event->msgu.rxmsg_ls.messageData[FCODE];
messageData = &dw_event->msgu.rxmsg_ls.messageData[0];
//srclen = ADDR_BYTE_SIZE_S;
//fctrladdr_len = FRAME_CRTL_AND_ADDRESS_LS;
break;
case 0x88: //
memcpy(&srcAddr[0], &(dw_event->msgu.rxmsg_ss.sourceAddr[0]), ADDR_BYTE_SIZE_S);
memcpy(&dstAddr[0], &(dw_event->msgu.rxmsg_ss.destAddr[0]), ADDR_BYTE_SIZE_S);
fn_code = dw_event->msgu.rxmsg_ss.messageData[FCODE];
messageData = &dw_event->msgu.rxmsg_ss.messageData[0];
//srclen = ADDR_BYTE_SIZE_S;
//fctrladdr_len = FRAME_CRTL_AND_ADDRESS_S;
break;
}
if((inst->instToSleep == FALSE) && (inst->mode == LISTENER))//update received data, and go back to receiving frames
{
//do something with message data (e.g. could extract any ToFs and print them)
inst->testAppState = TA_RXE_WAIT ; // wait for next frame
dwt_setrxaftertxdelay(0);
}
else
{
//process ranging messages
fcode = fn_code;
tof_idx = srcAddr[0] & 0x3 ;
switch(fcode)
{
case RTLS_DEMO_MSG_ANCH_POLL:
case RTLS_DEMO_MSG_TAG_POLL:
{
inst->tagPollRxTime = dw_event->timeStamp ; //save Poll's Rx time
if(fcode == RTLS_DEMO_MSG_TAG_POLL) //got poll from Tag
{
inst->rangeNumA[srcAddr[0]&0x7] = messageData[POLL_RNUM]; //when anchor receives a poll, we need to remember the new range number
}
else //got poll from Anchor (initiator)
{
inst->rangeNumAAnc[tof_idx] = messageData[POLL_RNUM]; //when anchor receives poll from another anchor - save the range number
}
if (A1_ANCHOR_ADDR == inst->instanceAddress16) //this is A1
{
if(GATEWAY_ANCHOR_ADDR == (srcAddr[0] | ((uint32)(srcAddr[1] << 8)))) //poll is from A0
{
//configure the time A1 will poll A2 (it should be in half slot time from now)
inst->a1SlotTime = dw_event->uTimeStamp + (inst->slotPeriod);
//inst->instanceTimerEn = 1; - THIS IS ENABLED BELOW AFTER FINAL
// - means that if final is not received then A1 will not range to A2
}
}
//the response has been sent - await TX done event
if(dw_event->type_pend == DWT_SIG_TX_PENDING)
{
inst->testAppState = TA_TX_WAIT_CONF; // wait confirmation
inst->previousState = TA_TXRESPONSE_SENT_POLLRX ; //wait for TX confirmation of sent response
}
//already re-enabled the receiver
else if (dw_event->type_pend == DWT_SIG_RX_PENDING)
{
//stay in RX wait for next frame...
//RX is already enabled...
inst->testAppState = TA_RX_WAIT_DATA ; // wait for next frame
}
else //the DW1000 is idle (re-enable from the application level)
{
//stay in RX wait for next frame...
inst->testAppState = TA_RXE_WAIT ; // wait for next frame
}
}
break; //RTLS_DEMO_MSG_TAG_POLL
case RTLS_DEMO_MSG_ANCH_RESP2:
case RTLS_DEMO_MSG_ANCH_RESP:
{
uint8 currentRangeNum = (messageData[TOFRN] + 1); //current = previous + 1
if(GATEWAY_ANCHOR_ADDR == (srcAddr[0] | ((uint32)(srcAddr[1] << 8)))) //if response from gateway then use the correction factor
{
if(inst->mode == TAG)
{
// casting received bytes to int because this is a signed correction -0.5 periods to +1.5 periods
inst->tagSleepCorrection = (int16) (((uint16) messageData[RES_TAG_SLP1] << 8) + messageData[RES_TAG_SLP0]);
inst->tagSleepRnd = 0; // once we have initial response from Anchor #0 the slot correction acts and we don't need this anymore
}
}
//the response has been sent - await TX done event
if(dw_event->type_pend == DWT_SIG_TX_PENDING) //anchor received response from anchor ID - 1 so is sending it's response now back to tag
{
inst->testAppState = TA_TX_WAIT_CONF; // wait confirmation
inst->previousState = TA_TXRESPONSE_SENT_RESPRX ; //wait for TX confirmation of sent response
}
//already re-enabled the receiver
else if(dw_event->type_pend == DWT_SIG_RX_PENDING)
{
// stay in TA_RX_WAIT_DATA - receiver is already enabled.
}
//DW1000 idle - send the final
else //if(dw_event->type_pend == DWT_SIG_DW_IDLE)
{
if(((TAG == inst->mode) && (inst->rxResponseMask & 0x1)) //if A0's response received send the final
|| ((A1_ANCHOR_ADDR == inst->instanceAddress16) && (inst->rxResponseMaskAnc & 0x4))
|| ((GATEWAY_ANCHOR_ADDR == inst->instanceAddress16) && (inst->rxResponseMaskAnc & 0x2)) ) //if A1's response received
{
inst->testAppState = TA_TXFINAL_WAIT_SEND ; // send our response / the final
}
else //go to sleep
{
if(TAG == inst->mode)
{
inst->testAppState = TA_TXE_WAIT ; //go to TA_TXE_WAIT first to check if it's sleep time
inst->nextState = TA_TXPOLL_WAIT_SEND ;
inst->instToSleep = TRUE;
}
else
{
instance_backtoanchor(inst);
}
}
}
/*else
{
//stay in RX wait for next frame...
inst->testAppState = TA_RXE_WAIT ; // wait for next frame
}*/
if(fcode == RTLS_DEMO_MSG_ANCH_RESP) //tag to anchor mode
{
if(currentRangeNum == inst->rangeNum) //these are the previous ranges...
{
//copy the ToF and put into array (array holds last 4 ToFs)
memcpy(&inst->tofArray[(srcAddr[0]&0x3)], &(messageData[TOFR]), 4);
//check if the ToF is valid, this makes sure we only report valid ToFs
//e.g. consider the case of reception of response from anchor a1 (we are anchor a2)
//if a1 got a Poll with previous Range number but got no Final, then the response will have
//the correct range number but the range will be INVALID_TOF
if(inst->tofArray[(srcAddr[0]&0x3)] != INVALID_TOF)
{
inst->rxResponseMask |= (0x1 << (srcAddr[0]&0x3));
}
}
else
{
if(inst->tofArray[(srcAddr[0]&0x3)] != INVALID_TOF)
{
inst->tofArray[(srcAddr[0]&0x3)] = INVALID_TOF;
}
}
}
else //anchor to anchor (only gateway processes anchor to anchor ToFs)
{
//report the correct set of ranges (ranges from anchors A1, A2 need to match owns range number)
if((inst->gatewayAnchor)&&(currentRangeNum == inst->rangeNumAnc)) //these are the previous ranges...
{
inst->rangeNumAAnc[0] = inst->rangeNumAnc ;
//once A0 receives A2's response then it can report the 3 ToFs.
if(inst->rxResps[inst->rangeNumAnc] == 3)
//if(A2_ANCHOR_ADDR == (srcAddr[0] | ((uint32)(srcAddr[1] << 8))))
{
//copy the ToF and put into array, the array should have 3 ToFs A0-A1, A0-A2 and A1-A2
memcpy(&inst->tofArrayAnc[(srcAddr[0]+dstAddr[0])&0x3], &(messageData[TOFR]), 4);
//calculate all anchor - anchor ranges... and report
inst->newRange = instance_calcranges(&inst->tofArrayAnc[0], MAX_ANCHOR_LIST_SIZE, TOF_REPORT_A2A, &inst->rxResponseMaskAnc);
inst->rxResponseMaskReport = inst->rxResponseMaskAnc;
inst->rxResponseMaskAnc = 0;
inst->newRangeTime = dw_event->uTimeStamp ;
}
else
{
//copy the ToF and put into array (array holds last 4 ToFs)
memcpy(&inst->tofArrayAnc[(srcAddr[0]+dstAddr[0])&0x3], &(messageData[TOFR]), 4);
}
}
}
}
break; //RTLS_DEMO_MSG_ANCH_RESP
case RTLS_DEMO_MSG_ANCH_FINAL:
case RTLS_DEMO_MSG_TAG_FINAL:
{
int64 Rb, Da, Ra, Db ;
uint64 tagFinalTxTime = 0;
uint64 tagFinalRxTime = 0;
uint64 tagPollTxTime = 0;
uint64 anchorRespRxTime = 0;
uint64 tof = INVALID_TOF;
double RaRbxDaDb = 0;
double RbyDb = 0;
double RayDa = 0;
uint8 validResp = messageData[VRESP];
uint8 index = RRXT0 + 5*(inst->shortAdd_idx);
if((RTLS_DEMO_MSG_TAG_FINAL == fcode) &&
(inst->rangeNumA[srcAddr[0]&0x7] != messageData[POLL_RNUM])) //Final's range number needs to match Poll's or else discard this message
{
inst->testAppState = TA_RXE_WAIT ; // wait for next frame
break;
}
if((RTLS_DEMO_MSG_ANCH_FINAL == fcode) &&
(((inst->rangeNumAAnc[tof_idx] != messageData[POLL_RNUM]) //Final's range number needs to match Poll's or else discard this message
|| inst->gatewayAnchor) //gateway can ignore the Final (from A1 to A2 exchange)
|| (A3_ANCHOR_ADDR == inst->instanceAddress16))) //A3 does not care about Final from A1 or A0
{
inst->testAppState = TA_RXE_WAIT ; // wait for next frame
break;
}
if (A1_ANCHOR_ADDR == inst->instanceAddress16) //this is A1
{
if(GATEWAY_ANCHOR_ADDR == (srcAddr[0] | ((uint32)(srcAddr[1] << 8)))) //final is from A0
{
//ENABLE TIMER ONLY IF FINAL RECEIVED
inst->instanceTimerEn = 1;
}
}
//output data over USB...
inst->newRangeAncAddress = inst->instanceAddress16;
//if we got the final, maybe the tag did not get our response, so
//we can use other anchors responses/ToF if there are any.. and output..
//but we cannot calculate new range
if(((validResp & (0x1<<(inst->shortAdd_idx))) != 0))
{
// time of arrival of Final message
tagFinalRxTime = dw_event->timeStamp ; //Final's Rx time
/*
#if defined(DEBUG)
printf("FinalRx Timestamp: %4.15e\n", convertdevicetimetosecu(dw_event.timeStamp));
#endif
*/
inst->delayedReplyTime = 0 ;
// times measured at Tag extracted from the message buffer
// extract 40bit times
memcpy(&tagPollTxTime, &(messageData[PTXT]), 5);
memcpy(&anchorRespRxTime, &(messageData[index]), 5);
memcpy(&tagFinalTxTime, &(messageData[FTXT]), 5);
// poll response round trip delay time is calculated as
// (anchorRespRxTime - tagPollTxTime) - (anchorRespTxTime - tagPollRxTime)
Ra = (int64)((anchorRespRxTime - tagPollTxTime) & MASK_40BIT);
Db = (int64)((inst->txu.anchorRespTxTime - inst->tagPollRxTime) & MASK_40BIT);
// response final round trip delay time is calculated as
// (tagFinalRxTime - anchorRespTxTime) - (tagFinalTxTime - anchorRespRxTime)
Rb = (int64)((tagFinalRxTime - inst->txu.anchorRespTxTime) & MASK_40BIT);
Da = (int64)((tagFinalTxTime - anchorRespRxTime) & MASK_40BIT);
RaRbxDaDb = (((double)Ra))*(((double)Rb))
- (((double)Da))*(((double)Db));
RbyDb = ((double)Rb + (double)Db);
RayDa = ((double)Ra + (double)Da);
tof = (int32) ( RaRbxDaDb/(RbyDb + RayDa) );
}
//tag to anchor ranging
if(RTLS_DEMO_MSG_TAG_FINAL == fcode)
{
inst->newRangeTagAddress = srcAddr[0] + ((uint16) srcAddr[1] << 8);
//time-of-flight
inst->tof[inst->newRangeTagAddress & 0x7] = tof;
//calculate all tag - anchor ranges... and report
inst->newRange = instance_calcranges(&inst->tofArray[0], MAX_ANCHOR_LIST_SIZE, TOF_REPORT_T2A, &inst->rxResponseMask);
inst->rxResponseMaskReport = inst->rxResponseMask; //copy the valid mask to report
inst->rxResponseMask = 0;
//we have our range - update the own mask entry...
if(tof != INVALID_TOF) //check the last ToF entry is valid and copy into the current array
{
setTagDist(srcAddr[0], inst->shortAdd_idx); //copy distance from this anchor to the tag into array
inst->rxResponseMask = (0x1 << inst->shortAdd_idx);
inst->tofArray[inst->shortAdd_idx] = tof;
}
inst->newRangeTime = dw_event->uTimeStamp ;
}
else //anchor to anchor ranging
{
inst->newRangeTagAddress = srcAddr[0] + ((uint16) srcAddr[1] << 8);
//time-of-flight
inst->tofAnc[tof_idx] = tof;
}
//reset the response count
if(inst->rxResps[inst->rxRespsIdx] >= 0)
{
inst->rxResps[inst->rxRespsIdx] = -1 * inst->rxResps[inst->rxRespsIdx];
if(inst->rxResps[inst->rxRespsIdx] == 0) //as A0 will have this as 0 when ranging to A1
inst->rxResps[inst->rxRespsIdx] = -1 ;
}
instancesetantennadelays(); //this will update the antenna delay if it has changed
instancesettxpower(); // configure TX power if it has changed
inst->testAppState = TA_RXE_WAIT ; // wait for next frame
}
break; //RTLS_DEMO_MSG_TAG_FINAL
default:
{
//only enable receiver when not using double buffering
inst->testAppState = TA_RXE_WAIT ; // wait for next frame
dwt_setrxaftertxdelay(0);
}
break;
} //end switch (fcode)
if(dw_event->msgu.frame[0] & 0x20)
{
//as we only pass the received frame with the ACK request bit set after the ACK has been sent
instance_getevent(16); //get and clear the ACK sent event
}
} //end else
}
break ; //end of DWT_SIG_RX_OKAY
case DWT_SIG_RX_TIMEOUT :
{
event_data_t* dw_event = instance_getevent(17); //get and clear this event
#if defined(DEBUG)
printf("PD_DATA_TIMEOUT %d\n", inst->previousState) ;
#endif
//Anchor can time out and then need to send response - so will be in TX pending
if(dw_event->type_pend == DWT_SIG_TX_PENDING)
{
inst->testAppState = TA_TX_WAIT_CONF; // wait confirmation
inst->previousState = TA_TXRESPONSE_SENT_TORX ; //wait for TX confirmation of sent response
}
else if(dw_event->type_pend == DWT_SIG_DW_IDLE) //if timed out and back in receive then don't process as timeout
{
inst_processrxtimeout(inst);
}
//else if RX_PENDING then wait for next RX event...
message = 0; //clear the message as we have processed the event
}
break ;
case DWT_SIG_TX_AA_DONE: //ignore this event - just process the rx frame that was received before the ACK response
case 0:
default :
{
if(message) // == DWT_SIG_TX_DONE)
{
inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT;
}
if(inst->done == INST_NOT_DONE_YET) inst->done = INST_DONE_WAIT_FOR_NEXT_EVENT;
}
break;
}
break ; // end case TA_RX_WAIT_DATA
default:
#if defined(DEBUG)
printf("\nERROR - invalid state %d - what is going on??\n", inst->testAppState) ;
#endif
break;
} // end switch on testAppState
/*
*********************************************************************************************************
*
* loca_status dwt_config(eCHAN channel, ePRF prf, ePLEN PreambleLength, eCODE code, uint8_t nsSFD, DataRate db)
*
* 描 述 : 配置DW1000
*
* 输入参数 :
* channel：DW1000通道
prf：
PreambleLength：
code：
nsSFD：
db：
*
* 输出参数 : DW1000状态
*********************************************************************************************************
*/
static loca_status dwt_config(eCHAN channel, ePRF prf, ePLEN PreambleLength, eCODE code, uint8_t nsSFD, DataRate db)
{
dwt_config_t config;
dwt_txconfig_t txconfig;
uint8_t buf[2];
uint64_t eui64;
uint16_t panid;
eui64 = LOC_CFG_EUI;
panid = LOC_CFG_PANID;
config.chan = channel;
config.prf = prf;
config.txPreambLength = PreambleLength;
switch (PreambleLength)
{
case PLEN_64:
case PLEN_128:
config.rxPAC = DWT_PAC8;
break;
case PLEN_256:
case PLEN_512:
config.rxPAC = DWT_PAC16;
break;
case PLEN_1024:
config.rxPAC = DWT_PAC32;
break;
default:
config.rxPAC = DWT_PAC64;
break;
}
config.rxCode = code;
config.txCode = code;
config.nsSFD = nsSFD;
config.dataRate = db;
config.smartPowerEn = 0;
config.phrMode = 0;
txconfig.PGdly = dwt_pgdelay[channel];
txconfig.power = dwt_manualpwr[prf - 1][channel];
BSP_ChangeSPIRate(SPI_SLOW);
dwt_softreset();
if (dwt_initialise(DWT_LOADNONE) != DWT_SUCCESS)
{
BSP_ChangeSPIRate(SPI_FAST);
return LOCA_FAULT;
}
BSP_ChangeSPIRate(SPI_FAST);
if (dwt_readdevid() != DWT_DEVICE_ID)
{
return LOCA_FAULT;
}
buf[0] = 0x10;
dwt_writetodevice(GPIO_CTRL_ID,0x02,1,&buf[0]);
buf[0] = 0xf0;
buf[1] = 0xf0;
dwt_writetodevice(GPIO_CTRL_ID,0x08,2,&buf[0]);
dwt_configure(&config, 0);
dwt_xtaltrim(LOC_CFG_XTALRIM);
dwt_setrxantennadelay(0);
dwt_settxantennadelay(0);
dwt_setsmarttxpower(0);
dwt_configuretxrf(&txconfig);
dwt_enableframefilter(DWT_FF_NOTYPE_EN);
dwt_seteui((uint8_t *)&eui64);
dwt_setpanid(panid);
//开启硬件中断
//BSP_DWTIntEnable();
// dwt_setinterrupt( DWT_INT_TFRS, 1);
dwt_setrxmode(DWT_RX_NORMAL,0,0);
return LOCA_OK;
}