static inline void emc_timing_update(void)
{
int err;
emc_writel(0x1, EMC_TIMING_CONTROL);
err = wait_for_update(EMC_STATUS,
EMC_STATUS_TIMING_UPDATE_STALLED, false);
if (err) {
pr_err("%s: timing update error: %d", __func__, err);
BUG();
}
}
static inline void auto_cal_disable(void)
{
int err;
emc_writel(0, EMC_AUTO_CAL_INTERVAL);
err = wait_for_update(EMC_AUTO_CAL_STATUS,
EMC_AUTO_CAL_STATUS_ACTIVE, false);
if (err) {
pr_err("%s: disable auto-cal error: %d", __func__, err);
BUG();
}
}
static noinline void emc_set_clock(const struct tegra11_emc_table *next_timing,
const struct tegra11_emc_table *last_timing,
u32 clk_setting)
{
#ifndef EMULATE_CLOCK_SWITCH
int i, dll_change, pre_wait;
bool dyn_sref_enabled, zcal_long;
u32 emc_cfg_reg = emc_readl(EMC_CFG);
dyn_sref_enabled = emc_cfg_reg & EMC_CFG_DYN_SREF_ENABLE;
dll_change = get_dll_change(next_timing, last_timing);
zcal_long = (next_timing->burst_regs[EMC_ZCAL_INTERVAL_INDEX] != 0) &&
(last_timing->burst_regs[EMC_ZCAL_INTERVAL_INDEX] == 0);
/* FIXME: remove steps enumeration below? */
/* 1. clear clkchange_complete interrupts */
emc_writel(EMC_INTSTATUS_CLKCHANGE_COMPLETE, EMC_INTSTATUS);
/* 2. disable dynamic self-refresh and preset dqs vref, then wait for
possible self-refresh entry/exit and/or dqs vref settled - waiting
before the clock change decreases worst case change stall time */
pre_wait = 0;
if (dyn_sref_enabled) {
emc_cfg_reg &= ~EMC_CFG_DYN_SREF_ENABLE;
emc_writel(emc_cfg_reg, EMC_CFG);
pre_wait = 5; /* 5us+ for self-refresh entry/exit */
}
/* 2.5 check dq/dqs vref delay */
if (dqs_preset(next_timing, last_timing)) {
if (pre_wait < 3)
pre_wait = 3; /* 3us+ for dqs vref settled */
}
if (pre_wait) {
emc_timing_update();
udelay(pre_wait);
}
/* 3. disable auto-cal if vref mode is switching - removed */
/* 4. program burst shadow registers */
for (i = 0; i < next_timing->burst_regs_num; i++) {
if (!burst_reg_addr[i])
continue;
__raw_writel(next_timing->burst_regs[i], burst_reg_addr[i]);
}
for (i = 0; i < next_timing->emc_trimmers_num; i++) {
__raw_writel(next_timing->emc_trimmers_0[i],
emc0_base + emc_trimmer_offs[i]);
__raw_writel(next_timing->emc_trimmers_1[i],
emc1_base + emc_trimmer_offs[i]);
}
if ((dram_type == DRAM_TYPE_LPDDR2) &&
(dram_over_temp_state != DRAM_OVER_TEMP_NONE))
set_over_temp_timing(next_timing, dram_over_temp_state);
emc_cfg_reg &= ~EMC_CFG_UPDATE_MASK;
emc_cfg_reg |= next_timing->emc_cfg & EMC_CFG_UPDATE_MASK;
emc_writel(emc_cfg_reg, EMC_CFG);
wmb();
barrier();
/* 4.1 On ddr3 when DLL is re-started predict MRS long wait count and
overwrite DFS table setting */
if ((dram_type == DRAM_TYPE_DDR3) && (dll_change == DLL_CHANGE_ON))
overwrite_mrs_wait_cnt(next_timing, zcal_long);
/* 5.2 disable auto-refresh to save time after clock change */
ccfifo_writel(EMC_REFCTRL_DISABLE_ALL(dram_dev_num), EMC_REFCTRL);
/* 6. turn Off dll and enter self-refresh on DDR3 */
if (dram_type == DRAM_TYPE_DDR3) {
if (dll_change == DLL_CHANGE_OFF)
ccfifo_writel(next_timing->emc_mode_1, EMC_EMRS);
ccfifo_writel(DRAM_BROADCAST(dram_dev_num) |
EMC_SELF_REF_CMD_ENABLED, EMC_SELF_REF);
}
/* 7. flow control marker 2 */
ccfifo_writel(1, EMC_STALL_THEN_EXE_AFTER_CLKCHANGE);
/* 8. exit self-refresh on DDR3 */
if (dram_type == DRAM_TYPE_DDR3)
ccfifo_writel(DRAM_BROADCAST(dram_dev_num), EMC_SELF_REF);
/* 8.1 re-enable auto-refresh */
ccfifo_writel(EMC_REFCTRL_ENABLE_ALL(dram_dev_num), EMC_REFCTRL);
/* 9. set dram mode registers */
set_dram_mode(next_timing, last_timing, dll_change);
/* 10. issue zcal command if turning zcal On */
if (zcal_long) {
ccfifo_writel(EMC_ZQ_CAL_LONG_CMD_DEV0, EMC_ZQ_CAL);
if (dram_dev_num > 1)
ccfifo_writel(EMC_ZQ_CAL_LONG_CMD_DEV1, EMC_ZQ_CAL);
}
/* 10.1 dummy write to RO register to remove stall after change */
ccfifo_writel(0, EMC_CCFIFO_STATUS);
/* 11.5 program burst_up_down registers if emc rate is going down */
if (next_timing->rate < last_timing->rate) {
for (i = 0; i < next_timing->burst_up_down_regs_num; i++)
__raw_writel(next_timing->burst_up_down_regs[i],
burst_up_down_reg_addr[i]);
wmb();
}
/* 12-14. read any MC register to ensure the programming is done
change EMC clock source register wait for clk change completion */
do_clock_change(clk_setting);
/* 14.1 re-enable auto-refresh - moved to ccfifo in 8.1 */
/* 14.2 program burst_up_down registers if emc rate is going up */
if (next_timing->rate > last_timing->rate) {
for (i = 0; i < next_timing->burst_up_down_regs_num; i++)
__raw_writel(next_timing->burst_up_down_regs[i],
burst_up_down_reg_addr[i]);
wmb();
}
/* 15. set auto-cal interval */
if (next_timing->rev >= 0x42)
emc_writel(next_timing->emc_acal_interval,
EMC_AUTO_CAL_INTERVAL);
/* 16. restore dynamic self-refresh */
if (next_timing->emc_cfg & EMC_CFG_DYN_SREF_ENABLE) {
emc_cfg_reg |= EMC_CFG_DYN_SREF_ENABLE;
emc_writel(emc_cfg_reg, EMC_CFG);
}
/* 17. set zcal wait count */
emc_writel(next_timing->emc_zcal_cnt_long, EMC_ZCAL_WAIT_CNT);
/* 18. update restored timing */
udelay(2);
emc_timing_update();
#else
/* FIXME: implement */
pr_info("tegra11_emc: Configuring EMC rate %lu (setting: 0x%x)\n",
next_timing->rate, clk_setting);
#endif
}
