/* call this when setting the servo cycle time */
static int setServoCycleTime(double secs)
{
static int t;
rtapi_print_msg(RTAPI_MSG_INFO,
"MOTION: setting Servo cycle time to %ld nsecs\n", (long) (secs * 1e9));
/* make sure it's not zero */
if (secs <= 0.0) {
return -1;
}
emcmot_config_change();
/* compute the interpolation rate as nearest integer to traj/servo */
emcmotConfig->interpolationRate =
(int) (emcmotConfig->trajCycleTime / secs + 0.5);
/* set the cubic interpolation rate and PID cycle time */
for (t = 0; t < num_joints; t++) {
cubicSetInterpolationRate(&(joints[t].cubic),
emcmotConfig->interpolationRate);
cubicSetSegmentTime(&(joints[t].cubic), secs);
}
/* copy into status out */
emcmotConfig->servoCycleTime = secs;
return 0;
}
/* call this when setting the trajectory cycle time */
static int setTrajCycleTime(double secs)
{
static int t;
rtapi_print_msg(RTAPI_MSG_INFO,
"MOTION: setting Traj cycle time to %ld nsecs\n", (long) (secs * 1e9));
/* make sure it's not zero */
if (secs <= 0.0) {
return -1;
}
emcmot_config_change();
/* compute the interpolation rate as nearest integer to traj/servo */
if(emcmotConfig->servoCycleTime)
emcmotConfig->interpolationRate =
(int) (secs / emcmotConfig->servoCycleTime + 0.5);
else
emcmotConfig->interpolationRate = 1;
/* set traj planner */
tpSetCycleTime(&emcmotDebug->queue, secs);
/* set the free planners, cubic interpolation rate and segment time */
for (t = 0; t < num_joints; t++) {
cubicSetInterpolationRate(&(joints[t].cubic),
emcmotConfig->interpolationRate);
}
/* copy into status out */
emcmotConfig->trajCycleTime = secs;
return 0;
}
/* init_comm_buffers() allocates and initializes the command,
status, and error buffers used to communicate with the user
space parts of emc.
*/
static int init_comm_buffers(void)
{
int joint_num, n;
emcmot_joint_t *joint;
int retval;
rtapi_print_msg(RTAPI_MSG_INFO,
"MOTION: init_comm_buffers() starting...\n");
emcmotStruct = 0;
emcmotDebug = 0;
emcmotStatus = 0;
emcmotCommand = 0;
emcmotConfig = 0;
/* record the kinematics type of the machine */
kinType = kinematicsType();
/* allocate and initialize the shared memory structure */
emc_shmem_id = rtapi_shmem_new(key, mot_comp_id, sizeof(emcmot_struct_t));
if (emc_shmem_id < 0) {
rtapi_print_msg(RTAPI_MSG_ERR,
"MOTION: rtapi_shmem_new failed, returned %d\n", emc_shmem_id);
return -1;
}
retval = rtapi_shmem_getptr(emc_shmem_id, (void **) &emcmotStruct);
if (retval < 0) {
rtapi_print_msg(RTAPI_MSG_ERR,
"MOTION: rtapi_shmem_getptr failed, returned %d\n", retval);
return -1;
}
/* zero shared memory before doing anything else. */
memset(emcmotStruct, 0, sizeof(emcmot_struct_t));
/* we'll reference emcmotStruct directly */
emcmotCommand = &emcmotStruct->command;
emcmotStatus = &emcmotStruct->status;
emcmotConfig = &emcmotStruct->config;
emcmotDebug = &emcmotStruct->debug;
emcmotInternal = &emcmotStruct->internal;
emcmotError = &emcmotStruct->error;
/* init error struct */
emcmotErrorInit(emcmotError);
/* init command struct */
emcmotCommand->head = 0;
emcmotCommand->command = 0;
emcmotCommand->commandNum = 0;
emcmotCommand->tail = 0;
emcmotCommand->spindlesync = 0.0;
/* init status struct */
emcmotStatus->head = 0;
emcmotStatus->commandEcho = 0;
emcmotStatus->commandNumEcho = 0;
emcmotStatus->commandStatus = 0;
/* init more stuff */
emcmotDebug->head = 0;
emcmotConfig->head = 0;
emcmotStatus->motionFlag = 0;
SET_MOTION_ERROR_FLAG(0);
SET_MOTION_COORD_FLAG(0);
SET_MOTION_TELEOP_FLAG(0);
emcmotDebug->split = 0;
emcmotStatus->heartbeat = 0;
emcmotStatus->computeTime = 0.0;
emcmotConfig->numJoints = num_joints;
ZERO_EMC_POSE(emcmotStatus->carte_pos_cmd);
ZERO_EMC_POSE(emcmotStatus->carte_pos_fb);
emcmotStatus->vel = VELOCITY;
emcmotConfig->limitVel = VELOCITY;
emcmotStatus->acc = ACCELERATION;
emcmotStatus->feed_scale = 1.0;
emcmotStatus->spindle_scale = 1.0;
emcmotStatus->net_feed_scale = 1.0;
/* adaptive feed is off by default, feed override, spindle
override, and feed hold are on */
emcmotStatus->enables_new = FS_ENABLED | SS_ENABLED | FH_ENABLED;
emcmotStatus->enables_queued = emcmotStatus->enables_new;
emcmotStatus->id = 0;
emcmotStatus->depth = 0;
emcmotStatus->activeDepth = 0;
emcmotStatus->paused = 0;
emcmotStatus->overrideLimitMask = 0;
emcmotStatus->spindle.speed = 0.0;
SET_MOTION_INPOS_FLAG(1);
SET_MOTION_ENABLE_FLAG(0);
emcmotConfig->kinematics_type = kinType;
emcmotDebug->oldPos = emcmotStatus->carte_pos_cmd;
ZERO_EMC_POSE(emcmotDebug->oldVel);
emcmot_config_change();
/* init pointer to joint structs */
#ifdef STRUCTS_IN_SHMEM
joints = &(emcmotDebug->joints[0]);
#else
joints = &(joint_array[0]);
#endif
/* init per-joint stuff */
for (joint_num = 0; joint_num < num_joints; joint_num++) {
/* point to structure for this joint */
joint = &joints[joint_num];
/* init the config fields with some "reasonable" defaults" */
joint->type = 0;
joint->max_pos_limit = 1.0;
joint->min_pos_limit = -1.0;
joint->vel_limit = 1.0;
joint->acc_limit = 1.0;
joint->min_ferror = 0.01;
joint->max_ferror = 1.0;
joint->home_search_vel = 0.0;
joint->home_latch_vel = 0.0;
joint->home_final_vel = -1;
joint->home_offset = 0.0;
joint->home = 0.0;
joint->home_flags = 0;
joint->home_sequence = -1;
joint->backlash = 0.0;
joint->comp.entries = 0;
joint->comp.entry = &(joint->comp.array[0]);
/* the compensation code has -DBL_MAX at one end of the table
and +DBL_MAX at the other so _all_ commanded positions are
guaranteed to be covered by the table */
joint->comp.array[0].nominal = -DBL_MAX;
joint->comp.array[0].fwd_trim = 0.0;
joint->comp.array[0].rev_trim = 0.0;
joint->comp.array[0].fwd_slope = 0.0;
joint->comp.array[0].rev_slope = 0.0;
for ( n = 1 ; n < EMCMOT_COMP_SIZE+2 ; n++ ) {
joint->comp.array[n].nominal = DBL_MAX;
joint->comp.array[n].fwd_trim = 0.0;
joint->comp.array[n].rev_trim = 0.0;
joint->comp.array[n].fwd_slope = 0.0;
joint->comp.array[n].rev_slope = 0.0;
}
/* init status info */
joint->flag = 0;
joint->coarse_pos = 0.0;
joint->pos_cmd = 0.0;
joint->vel_cmd = 0.0;
joint->backlash_corr = 0.0;
joint->backlash_filt = 0.0;
joint->backlash_vel = 0.0;
joint->motor_pos_cmd = 0.0;
joint->motor_pos_fb = 0.0;
joint->pos_fb = 0.0;
joint->ferror = 0.0;
joint->ferror_limit = joint->min_ferror;
joint->ferror_high_mark = 0.0;
/* init internal info */
cubicInit(&(joint->cubic));
/* init misc other stuff in joint structure */
joint->big_vel = 10.0 * joint->vel_limit;
joint->home_state = 0;
/* init joint flags (reduntant, since flag = 0 */
SET_JOINT_ENABLE_FLAG(joint, 0);
SET_JOINT_ACTIVE_FLAG(joint, 0);
SET_JOINT_NHL_FLAG(joint, 0);
SET_JOINT_PHL_FLAG(joint, 0);
SET_JOINT_INPOS_FLAG(joint, 1);
SET_JOINT_HOMING_FLAG(joint, 0);
SET_JOINT_HOMED_FLAG(joint, 0);
SET_JOINT_FERROR_FLAG(joint, 0);
SET_JOINT_FAULT_FLAG(joint, 0);
SET_JOINT_ERROR_FLAG(joint, 0);
}
/*! \todo FIXME-- add emcmotError */
emcmotDebug->tMin = 0.0;
emcmotDebug->tMax = 0.0;
emcmotDebug->tAvg = 0.0;
emcmotDebug->sMin = 0.0;
emcmotDebug->sMax = 0.0;
emcmotDebug->sAvg = 0.0;
emcmotDebug->nMin = 0.0;
emcmotDebug->nMax = 0.0;
emcmotDebug->nAvg = 0.0;
emcmotDebug->yMin = 0.0;
emcmotDebug->yMax = 0.0;
emcmotDebug->yAvg = 0.0;
emcmotDebug->fyMin = 0.0;
emcmotDebug->fyMax = 0.0;
emcmotDebug->fyAvg = 0.0;
emcmotDebug->fMin = 0.0;
emcmotDebug->fMax = 0.0;
emcmotDebug->fAvg = 0.0;
emcmotDebug->cur_time = emcmotDebug->last_time = 0.0;
emcmotDebug->start_time = etime();
emcmotDebug->running_time = 0.0;
/* init motion emcmotDebug->queue */
if (-1 == tpCreate(&emcmotDebug->queue, DEFAULT_TC_QUEUE_SIZE,
emcmotDebug->queueTcSpace)) {
rtapi_print_msg(RTAPI_MSG_ERR,
"MOTION: failed to create motion emcmotDebug->queue\n");
return -1;
}
// tpInit(&emcmotDebug->queue); // tpInit called from tpCreate
tpSetCycleTime(&emcmotDebug->queue, emcmotConfig->trajCycleTime);
tpSetPos(&emcmotDebug->queue, emcmotStatus->carte_pos_cmd);
tpSetVmax(&emcmotDebug->queue, emcmotStatus->vel, emcmotStatus->vel);
tpSetAmax(&emcmotDebug->queue, emcmotStatus->acc);
emcmotStatus->tail = 0;
rtapi_print_msg(RTAPI_MSG_INFO, "MOTION: init_comm_buffers() complete\n");
return 0;
}
static int init_comm_buffers(void) {
int joint_num, n;
emcmot_joint_t *joint;
int retval;
int shmem_id;
rtapi_print_msg(RTAPI_MSG_INFO,
"MOTION: init_comm_buffers() starting...\n");
emcmotStruct = 0;
emcmotDebug = 0;
emcmotStatus = 0;
c = 0;
emcmotConfig = 0;
/* allocate and initialize the shared memory structure */
shmem_id = rtapi_shmem_new(DEFAULT_SHMEM_KEY, mot_comp_id, sizeof(emcmot_struct_t));
if (shmem_id < 0) {
rtapi_print_msg(RTAPI_MSG_ERR,
"MOTION: rtapi_shmem_new failed, returned %d\n", shmem_id);
return -1;
}
retval = rtapi_shmem_getptr(shmem_id, (void **) &emcmotStruct);
if (retval < 0) {
rtapi_print_msg(RTAPI_MSG_ERR,
"MOTION: rtapi_shmem_getptr failed, returned %d\n", retval);
return -1;
}
/* zero shared memory before doing anything else. */
memset(emcmotStruct, 0, sizeof(emcmot_struct_t));
/* we'll reference emcmotStruct directly */
c = &emcmotStruct->command;
emcmotStatus = &emcmotStruct->status;
emcmotConfig = &emcmotStruct->config;
emcmotDebug = &emcmotStruct->debug;
emcmotInternal = &emcmotStruct->internal;
emcmotError = &emcmotStruct->error;
emcmotConfig->numJoints = num_joints;
emcmotStatus->vel = DEFAULT_VELOCITY;
emcmotConfig->limitVel = DEFAULT_VELOCITY;
emcmotStatus->acc = DEFAULT_ACCELERATION;
emcmotStatus->feed_scale = 1.0;
emcmotStatus->rapid_scale = 1.0;
emcmotStatus->spindle_scale = 1.0;
emcmotStatus->net_feed_scale = 1.0;
/* adaptive feed is off by default, feed override, spindle
override, and feed hold are on */
emcmotStatus->enables_new = FS_ENABLED | SS_ENABLED | FH_ENABLED;
emcmotStatus->enables_queued = emcmotStatus->enables_new;
SET_MOTION_INPOS_FLAG(1);
emcmotConfig->kinematics_type = KINEMATICS_IDENTITY;
emcmot_config_change();
/* init pointer to joint structs */
joints = joint_array;
/* init per-joint stuff */
for (joint_num = 0; joint_num < num_joints; joint_num++) {
/* point to structure for this joint */
joint = &joints[joint_num];
/* init the config fields with some "reasonable" defaults" */
joint->max_pos_limit = 1.0;
joint->min_pos_limit = -1.0;
joint->vel_limit = 1.0;
joint->acc_limit = 1.0;
joint->min_ferror = 0.01;
joint->max_ferror = 1.0;
joint->home_final_vel = -1;
joint->home_sequence = -1;
joint->comp.entry = &(joint->comp.array[0]);
/* the compensation code has -DBL_MAX at one end of the table
and +DBL_MAX at the other so _all_ commanded positions are
guaranteed to be covered by the table */
joint->comp.array[0].nominal = -DBL_MAX;
joint->comp.array[0].fwd_trim = 0.0;
joint->comp.array[0].rev_trim = 0.0;
joint->comp.array[0].fwd_slope = 0.0;
joint->comp.array[0].rev_slope = 0.0;
for ( n = 1 ; n < EMCMOT_COMP_SIZE+2 ; n++ ) {
joint->comp.array[n].nominal = DBL_MAX;
joint->comp.array[n].fwd_trim = 0.0;
joint->comp.array[n].rev_trim = 0.0;
joint->comp.array[n].fwd_slope = 0.0;
joint->comp.array[n].rev_slope = 0.0;
}
/* init status info */
joint->ferror_limit = joint->min_ferror;
/* init misc other stuff in joint structure */
joint->big_vel = 10.0 * joint->vel_limit;
SET_JOINT_INPOS_FLAG(joint, 1);
}
emcmotDebug->start_time = time(NULL);
rtapi_print_msg(RTAPI_MSG_INFO, "MOTION: init_comm_buffers() complete\n");
return 0;
}
/*
emcmotCommandHandler() is called each main cycle to read the
shared memory buffer
*/
void emcmotCommandHandler(void *arg, long period)
{
int joint_num;
emcmot_joint_t *joint;
double tmp1;
emcmot_comp_entry_t *comp_entry;
check_stuff ( "before command_handler()" );
/* check for split read */
if (emcmotCommand->head != emcmotCommand->tail) {
emcmotDebug->split++;
return; /* not really an error */
}
if (emcmotCommand->commandNum != emcmotStatus->commandNumEcho) {
/* increment head count-- we'll be modifying emcmotStatus */
emcmotStatus->head++;
emcmotDebug->head++;
/* got a new command-- echo command and number... */
emcmotStatus->commandEcho = emcmotCommand->command;
emcmotStatus->commandNumEcho = emcmotCommand->commandNum;
/* clear status value by default */
emcmotStatus->commandStatus = EMCMOT_COMMAND_OK;
/* ...and process command */
/* Many commands uses "command->axis" to indicate which joint they
wish to operate on. This code eliminates the need to copy
command->axis to "joint_num", limit check it, and then set "joint"
to point to the joint data. All the individual commands need to do
is verify that "joint" is non-zero. */
joint_num = emcmotCommand->axis;
if (joint_num >= 0 && joint_num < num_joints) {
/* valid joint, point to it's data */
joint = &joints[joint_num];
} else {
/* bad joint number */
joint = 0;
}
/* printing of commands for troubleshooting */
rtapi_print_msg(RTAPI_MSG_DBG, "%d: CMD %d, code %3d ", emcmotStatus->heartbeat,
emcmotCommand->commandNum, emcmotCommand->command);
switch (emcmotCommand->command) {
case EMCMOT_ABORT:
/* abort motion */
/* can happen at any time */
/* this command attempts to stop all machine motion. it looks at
the current mode and acts accordingly, if in teleop mode, it
sets the desired velocities to zero, if in coordinated mode,
it calls the traj planner abort function (don't know what that
does yet), and if in free mode, it disables the free mode traj
planners which stops axis motion */
rtapi_print_msg(RTAPI_MSG_DBG, "ABORT");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", emcmotCommand->axis);
/* check for coord or free space motion active */
if (GET_MOTION_TELEOP_FLAG()) {
emcmotDebug->teleop_data.desiredVel.tran.x = 0.0;
emcmotDebug->teleop_data.desiredVel.tran.y = 0.0;
emcmotDebug->teleop_data.desiredVel.tran.z = 0.0;
emcmotDebug->teleop_data.desiredVel.a = 0.0;
emcmotDebug->teleop_data.desiredVel.b = 0.0;
emcmotDebug->teleop_data.desiredVel.c = 0.0;
} else if (GET_MOTION_COORD_FLAG()) {
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(0);
} else {
for (joint_num = 0; joint_num < num_joints; joint_num++) {
/* point to joint struct */
joint = &joints[joint_num];
/* tell joint planner to stop */
joint->free_tp_enable = 0;
/* stop homing if in progress */
if ( joint->home_state != HOME_IDLE ) {
joint->home_state = HOME_ABORT;
}
}
}
/* clear axis errors (regardless of mode */
for (joint_num = 0; joint_num < num_joints; joint_num++) {
/* point to joint struct */
joint = &joints[joint_num];
/* update status flags */
SET_JOINT_ERROR_FLAG(joint, 0);
SET_JOINT_FAULT_FLAG(joint, 0);
}
break;
case EMCMOT_AXIS_ABORT:
/* abort one axis */
/* can happen at any time */
/* this command stops a single axis. It is only usefull
in free mode, so in coord or teleop mode it does
nothing. */
rtapi_print_msg(RTAPI_MSG_DBG, "AXIS_ABORT");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", emcmotCommand->axis);
if (GET_MOTION_TELEOP_FLAG()) {
/* do nothing in teleop mode */
} else if (GET_MOTION_COORD_FLAG()) {
/* do nothing in coord mode */
} else {
/* validate joint */
if (joint == 0) {
break;
}
/* tell joint planner to stop */
joint->free_tp_enable = 0;
/* stop homing if in progress */
if ( joint->home_state != HOME_IDLE ) {
joint->home_state = HOME_ABORT;
}
/* update status flags */
SET_JOINT_ERROR_FLAG(joint, 0);
}
break;
case EMCMOT_FREE:
/* change the mode to free axis motion */
/* can be done at any time */
/* this code doesn't actually make the transition, it merely
requests the transition by clearing a couple of flags */
/* reset the emcmotDebug->coordinating flag to defer transition
to controller cycle */
rtapi_print_msg(RTAPI_MSG_DBG, "FREE");
emcmotDebug->coordinating = 0;
emcmotDebug->teleoperating = 0;
break;
case EMCMOT_COORD:
/* change the mode to coordinated axis motion */
/* can be done at any time */
/* this code doesn't actually make the transition, it merely
tests a condition and then sets a flag requesting the
transition */
/* set the emcmotDebug->coordinating flag to defer transition to
controller cycle */
rtapi_print_msg(RTAPI_MSG_DBG, "COORD");
emcmotDebug->coordinating = 1;
emcmotDebug->teleoperating = 0;
if (kinType != KINEMATICS_IDENTITY) {
if (!checkAllHomed()) {
reportError
("all axes must be homed before going into coordinated mode");
emcmotDebug->coordinating = 0;
break;
}
}
break;
case EMCMOT_TELEOP:
/* change the mode to teleop motion */
/* can be done at any time */
/* this code doesn't actually make the transition, it merely
tests a condition and then sets a flag requesting the
transition */
/* set the emcmotDebug->teleoperating flag to defer transition to
controller cycle */
rtapi_print_msg(RTAPI_MSG_DBG, "TELEOP");
emcmotDebug->teleoperating = 1;
if (kinType != KINEMATICS_IDENTITY) {
if (!checkAllHomed()) {
reportError
("all axes must be homed before going into teleop mode");
emcmotDebug->teleoperating = 0;
break;
}
}
break;
case EMCMOT_SET_NUM_AXES:
/* set the global NUM_AXES, which must be between 1 and
EMCMOT_MAX_AXIS, inclusive */
/* this sets a global - I hate globals - hopefully this can be
moved into the config structure, or dispensed with completely */
rtapi_print_msg(RTAPI_MSG_DBG, "SET_NUM_AXES");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", emcmotCommand->axis);
if (( emcmotCommand->axis <= 0 ) ||
( emcmotCommand->axis > EMCMOT_MAX_AXIS )) {
break;
}
num_axes = emcmotCommand->axis;
emcmotConfig->numAxes = num_axes;
break;
case EMCMOT_SET_WORLD_HOME:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_WORLD_HOME");
emcmotStatus->world_home = emcmotCommand->pos;
break;
case EMCMOT_SET_HOMING_PARAMS:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_HOMING_PARAMS");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
emcmot_config_change();
if (joint == 0) {
break;
}
joint->home_offset = emcmotCommand->offset;
joint->home = emcmotCommand->home;
joint->home_search_vel = emcmotCommand->search_vel;
joint->home_latch_vel = emcmotCommand->latch_vel;
joint->home_flags = emcmotCommand->flags;
joint->home_sequence = emcmotCommand->home_sequence;
break;
case EMCMOT_OVERRIDE_LIMITS:
/* this command can be issued with axix < 0 to re-enable
limits, but they are automatically re-enabled at the
end of the next jog */
rtapi_print_msg(RTAPI_MSG_DBG, "OVERRIDE_LIMITS");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", emcmotCommand->axis);
if (emcmotCommand->axis < 0) {
/* don't override limits */
rtapi_print_msg(RTAPI_MSG_DBG, "override off");
emcmotStatus->overrideLimitMask = 0;
} else {
rtapi_print_msg(RTAPI_MSG_DBG, "override on");
emcmotStatus->overrideLimitMask = 0;
for (joint_num = 0; joint_num < num_joints; joint_num++) {
/* point at joint data */
joint = &joints[joint_num];
#if 0 // Original code commented by KSU to allow tripped axis move
/* only override limits that are currently tripped */
if ( GET_JOINT_NHL_FLAG(joint) ) {
emcmotStatus->overrideLimitMask |= (1 << (joint_num*2));
}
if ( GET_JOINT_PHL_FLAG(joint) ) {
emcmotStatus->overrideLimitMask |= (2 << (joint_num*2));
}
#else
emcmotStatus->overrideLimitMask |= (1 << (joint_num*2));
emcmotStatus->overrideLimitMask |= (2 << (joint_num*2));
#endif
}
}
emcmotDebug->overriding = 0;
for (joint_num = 0; joint_num < num_joints; joint_num++) {
/* point at joint data */
joint = &joints[joint_num];
/* clear joint errors */
SET_JOINT_ERROR_FLAG(joint, 0);
}
break;
case EMCMOT_SET_MOTOR_OFFSET:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_MOTOR_OFFSET");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", emcmotCommand->axis);
if(joint == 0) {
break;
}
joint->motor_offset = emcmotCommand->motor_offset;
break;
case EMCMOT_SET_POSITION_LIMITS:
/* sets soft limits for an axis */
rtapi_print_msg(RTAPI_MSG_DBG, "SET_POSITION_LIMITS");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
emcmot_config_change();
/* set the position limits for the axis */
/* can be done at any time */
if (joint == 0) {
break;
}
joint->min_pos_limit = emcmotCommand->minLimit;
joint->max_pos_limit = emcmotCommand->maxLimit;
break;
case EMCMOT_SET_BACKLASH:
/* sets backlash for an axis */
rtapi_print_msg(RTAPI_MSG_DBG, "SET_BACKLASH");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
emcmot_config_change();
/* set the backlash for the axis */
/* can be done at any time */
if (joint == 0) {
break;
}
joint->backlash = emcmotCommand->backlash;
break;
/*
Max and min ferror work like this: limiting ferror is
determined by slope of ferror line, = maxFerror/limitVel ->
limiting ferror = maxFerror/limitVel * vel. If ferror <
minFerror then OK else if ferror < limiting ferror then OK
else ERROR */
case EMCMOT_SET_MAX_FERROR:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_MAX_FERROR");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
emcmot_config_change();
if (joint == 0 || emcmotCommand->maxFerror < 0.0) {
break;
}
joint->max_ferror = emcmotCommand->maxFerror;
break;
case EMCMOT_SET_MIN_FERROR:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_MIN_FERROR");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
emcmot_config_change();
if (joint == 0 || emcmotCommand->minFerror < 0.0) {
break;
}
joint->min_ferror = emcmotCommand->minFerror;
break;
case EMCMOT_JOG_CONT:
/* do a continuous jog, implemented as an incremental jog to the
limit. When the user lets go of the button an abort will
stop the jog. */
rtapi_print_msg(RTAPI_MSG_DBG, "JOG_CONT");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
/* check axis range */
if (joint == 0) {
break;
}
/* must be in free mode and enabled */
if (GET_MOTION_COORD_FLAG()) {
reportError("Can't jog axis in coordinated mode.");
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
if (!GET_MOTION_ENABLE_FLAG()) {
reportError("Can't jog axis when not enabled.");
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
if (emcmotStatus->homing_active) {
reportError("Can't jog any axis while homing.");
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
if (joint->wheel_jog_active) {
/* can't do two kinds of jog at once */
break;
}
if (emcmotStatus->net_feed_scale < 0.0001 ) {
/* don't jog if feedhold is on or if feed override is zero */
break;
}
/* don't jog further onto limits */
if (!jog_ok(joint_num, emcmotCommand->vel)) {
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
/* set destination of jog */
refresh_jog_limits(joint);
if (emcmotCommand->vel > 0.0) {
joint->free_pos_cmd = joint->max_jog_limit;
} else {
joint->free_pos_cmd = joint->min_jog_limit;
}
/* set velocity of jog */
joint->free_vel_lim = fabs(emcmotCommand->vel);
/* lock out other jog sources */
joint->kb_jog_active = 1;
/* and let it go */
joint->free_tp_enable = 1;
/*! \todo FIXME - should we really be clearing errors here? */
SET_JOINT_ERROR_FLAG(joint, 0);
/* clear axis homed flag(s) if we don't have forward kins.
Otherwise, a transition into coordinated mode will incorrectly
assume the homed position. Do all if they've all been moved
since homing, otherwise just do this one */
clearHomes(joint_num);
break;
case EMCMOT_JOG_INCR:
/* do an incremental jog */
/* check axis range */
rtapi_print_msg(RTAPI_MSG_DBG, "JOG_INCR");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
if (joint == 0) {
break;
}
/* must be in free mode and enabled */
if (GET_MOTION_COORD_FLAG()) {
reportError("Can't jog axis in coordinated mode.");
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
if (!GET_MOTION_ENABLE_FLAG()) {
reportError("Can't jog axis when not enabled.");
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
if (emcmotStatus->homing_active) {
reportError("Can't jog any axis while homing.");
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
if (joint->wheel_jog_active) {
/* can't do two kinds of jog at once */
break;
}
if (emcmotStatus->net_feed_scale < 0.0001 ) {
/* don't jog if feedhold is on or if feed override is zero */
break;
}
/* don't jog further onto limits */
if (!jog_ok(joint_num, emcmotCommand->vel)) {
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
/* set target position for jog */
if (emcmotCommand->vel > 0.0) {
tmp1 = joint->free_pos_cmd + emcmotCommand->offset;
} else {
tmp1 = joint->free_pos_cmd - emcmotCommand->offset;
}
/* don't jog past limits */
refresh_jog_limits(joint);
if (tmp1 > joint->max_jog_limit) {
break;
}
if (tmp1 < joint->min_jog_limit) {
break;
}
/* set target position */
joint->free_pos_cmd = tmp1;
/* set velocity of jog */
joint->free_vel_lim = fabs(emcmotCommand->vel);
/* lock out other jog sources */
joint->kb_jog_active = 1;
/* and let it go */
joint->free_tp_enable = 1;
SET_JOINT_ERROR_FLAG(joint, 0);
/* clear axis homed flag(s) if we don't have forward kins.
Otherwise, a transition into coordinated mode will incorrectly
assume the homed position. Do all if they've all been moved
since homing, otherwise just do this one */
clearHomes(joint_num);
break;
case EMCMOT_JOG_ABS:
/* do an absolute jog */
/* check axis range */
rtapi_print_msg(RTAPI_MSG_DBG, "JOG_ABS");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
if (joint == 0) {
break;
}
/* must be in free mode and enabled */
if (GET_MOTION_COORD_FLAG()) {
reportError("Can't jog axis in coordinated mode.");
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
if (!GET_MOTION_ENABLE_FLAG()) {
reportError("Can't jog axis when not enabled.");
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
if (emcmotStatus->homing_active) {
reportError("Can't jog any axis while homing.");
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
if (joint->wheel_jog_active) {
/* can't do two kinds of jog at once */
break;
}
if (emcmotStatus->net_feed_scale < 0.0001 ) {
/* don't jog if feedhold is on or if feed override is zero */
break;
}
/* don't jog further onto limits */
if (!jog_ok(joint_num, emcmotCommand->vel)) {
SET_JOINT_ERROR_FLAG(joint, 1);
break;
}
/*! \todo FIXME-- use 'goal' instead */
joint->free_pos_cmd = emcmotCommand->offset;
/* don't jog past limits */
refresh_jog_limits(joint);
if (joint->free_pos_cmd > joint->max_jog_limit) {
joint->free_pos_cmd = joint->max_jog_limit;
}
if (joint->free_pos_cmd < joint->min_jog_limit) {
joint->free_pos_cmd = joint->min_jog_limit;
}
/* set velocity of jog */
joint->free_vel_lim = fabs(emcmotCommand->vel);
/* lock out other jog sources */
joint->kb_jog_active = 1;
/* and let it go */
joint->free_tp_enable = 1;
SET_JOINT_ERROR_FLAG(joint, 0);
/* clear axis homed flag(s) if we don't have forward kins.
Otherwise, a transition into coordinated mode will incorrectly
assume the homed position. Do all if they've all been moved
since homing, otherwise just do this one */
clearHomes(joint_num);
break;
case EMCMOT_SET_TERM_COND:
/* sets termination condition for motion emcmotDebug->queue */
rtapi_print_msg(RTAPI_MSG_DBG, "SET_TERM_COND");
tpSetTermCond(&emcmotDebug->queue, emcmotCommand->termCond, emcmotCommand->tolerance);
break;
case EMCMOT_SET_SPINDLESYNC:
tpSetSpindleSync(&emcmotDebug->queue, emcmotCommand->spindlesync, emcmotCommand->flags);
break;
case EMCMOT_SET_LINE:
/* emcmotDebug->queue up a linear move */
/* requires coordinated mode, enable off, not on limits */
rtapi_print_msg(RTAPI_MSG_DBG, "SET_LINE");
if (!GET_MOTION_COORD_FLAG() || !GET_MOTION_ENABLE_FLAG()) {
reportError
("need to be enabled, in coord mode for linear move");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_COMMAND;
SET_MOTION_ERROR_FLAG(1);
break;
} else if (!inRange(emcmotCommand->pos)) {
if(emcmotCommand->id > 0)
reportError("linear move on line %d would exceed limits",
emcmotCommand->id);
else
reportError("linear move in MDI would exceed limits");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_PARAMS;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
} else if (!limits_ok()) {
reportError("can't do linear move with limits exceeded");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_PARAMS;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
}
/* append it to the emcmotDebug->queue */
tpSetId(&emcmotDebug->queue, emcmotCommand->id);
if (-1 == tpAddLine(&emcmotDebug->queue, emcmotCommand->pos, emcmotCommand->motion_type, emcmotCommand->vel, emcmotCommand->ini_maxvel, emcmotCommand->acc, emcmotStatus->enables_new)) {
reportError("can't add linear move");
emcmotStatus->commandStatus = EMCMOT_COMMAND_BAD_EXEC;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
} else {
SET_MOTION_ERROR_FLAG(0);
/* set flag that indicates all axes need rehoming, if any
axis is moved in joint mode, for machines with no forward
kins */
rehomeAll = 1;
}
break;
case EMCMOT_SET_CIRCLE:
/* emcmotDebug->queue up a circular move */
/* requires coordinated mode, enable on, not on limits */
rtapi_print_msg(RTAPI_MSG_DBG, "SET_CIRCLE");
if (!GET_MOTION_COORD_FLAG() || !GET_MOTION_ENABLE_FLAG()) {
reportError
("need to be enabled, in coord mode for circular move");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_COMMAND;
SET_MOTION_ERROR_FLAG(1);
break;
} else if (!inRange(emcmotCommand->pos)) {
if(emcmotCommand->id > 0)
reportError("circular move on line %d would exceed limits",
emcmotCommand->id);
else
reportError("circular move in MDI would exceed limits");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_PARAMS;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
} else if (!limits_ok()) {
reportError("can't do circular move with limits exceeded");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_PARAMS;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
}
/* append it to the emcmotDebug->queue */
tpSetId(&emcmotDebug->queue, emcmotCommand->id);
if (-1 ==
tpAddCircle(&emcmotDebug->queue, emcmotCommand->pos,
emcmotCommand->center, emcmotCommand->normal,
emcmotCommand->turn, emcmotCommand->motion_type,
emcmotCommand->vel, emcmotCommand->ini_maxvel,
emcmotCommand->acc, emcmotStatus->enables_new)) {
reportError("can't add circular move");
emcmotStatus->commandStatus = EMCMOT_COMMAND_BAD_EXEC;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
} else {
SET_MOTION_ERROR_FLAG(0);
/* set flag that indicates all axes need rehoming, if any
axis is moved in joint mode, for machines with no forward
kins */
rehomeAll = 1;
}
break;
case EMCMOT_SET_VEL:
/* set the velocity for subsequent moves */
/* can do it at any time */
rtapi_print_msg(RTAPI_MSG_DBG, "SET_VEL");
emcmotStatus->vel = emcmotCommand->vel;
tpSetVmax(&emcmotDebug->queue, emcmotStatus->vel,
emcmotCommand->ini_maxvel);
break;
case EMCMOT_SET_VEL_LIMIT:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_VEL_LIMIT");
emcmot_config_change();
/* set the absolute max velocity for all subsequent moves */
/* can do it at any time */
emcmotConfig->limitVel = emcmotCommand->vel;
tpSetVlimit(&emcmotDebug->queue, emcmotConfig->limitVel);
break;
case EMCMOT_SET_JOINT_VEL_LIMIT:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_JOINT_VEL_LIMIT");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
emcmot_config_change();
/* check axis range */
if (joint == 0) {
break;
}
joint->vel_limit = emcmotCommand->vel;
joint->big_vel = 10 * emcmotCommand->vel;
break;
case EMCMOT_SET_JOINT_ACC_LIMIT:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_JOINT_ACC_LIMIT");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
emcmot_config_change();
/* check axis range */
if (joint == 0) {
break;
}
joint->acc_limit = emcmotCommand->acc;
break;
case EMCMOT_SET_ACC:
/* set the max acceleration */
/* can do it at any time */
rtapi_print_msg(RTAPI_MSG_DBG, "SET_ACCEL");
emcmotStatus->acc = emcmotCommand->acc;
tpSetAmax(&emcmotDebug->queue, emcmotStatus->acc);
break;
case EMCMOT_PAUSE:
/* pause the motion */
/* can happen at any time */
rtapi_print_msg(RTAPI_MSG_DBG, "PAUSE");
tpPause(&emcmotDebug->queue);
emcmotStatus->paused = 1;
break;
case EMCMOT_RESUME:
/* resume paused motion */
/* can happen at any time */
rtapi_print_msg(RTAPI_MSG_DBG, "RESUME");
emcmotDebug->stepping = 0;
tpResume(&emcmotDebug->queue);
emcmotStatus->paused = 0;
break;
case EMCMOT_STEP:
/* resume paused motion until id changes */
/* can happen at any time */
rtapi_print_msg(RTAPI_MSG_DBG, "STEP");
if(emcmotStatus->paused) {
emcmotDebug->idForStep = emcmotStatus->id;
emcmotDebug->stepping = 1;
tpResume(&emcmotDebug->queue);
emcmotStatus->paused = 1;
} else {
reportError("MOTION: can't STEP while already executing");
}
break;
case EMCMOT_FEED_SCALE:
/* override speed */
/* can happen at any time */
rtapi_print_msg(RTAPI_MSG_DBG, "FEED SCALE");
if (emcmotCommand->scale < 0.0) {
emcmotCommand->scale = 0.0; /* clamp it */
}
emcmotStatus->feed_scale = emcmotCommand->scale;
break;
case EMCMOT_FS_ENABLE:
/* enable/disable overriding speed */
/* can happen at any time */
if ( emcmotCommand->mode != 0 ) {
rtapi_print_msg(RTAPI_MSG_DBG, "FEED SCALE: ON");
emcmotStatus->enables_new |= FS_ENABLED;
} else {
rtapi_print_msg(RTAPI_MSG_DBG, "FEED SCALE: OFF");
emcmotStatus->enables_new &= ~FS_ENABLED;
}
break;
case EMCMOT_FH_ENABLE:
/* enable/disable feed hold */
/* can happen at any time */
if ( emcmotCommand->mode != 0 ) {
rtapi_print_msg(RTAPI_MSG_DBG, "FEED HOLD: ENABLED");
emcmotStatus->enables_new |= FH_ENABLED;
} else {
rtapi_print_msg(RTAPI_MSG_DBG, "FEED HOLD: DISABLED");
emcmotStatus->enables_new &= ~FH_ENABLED;
}
break;
case EMCMOT_SPINDLE_SCALE:
/* override spindle speed */
/* can happen at any time */
rtapi_print_msg(RTAPI_MSG_DBG, "SPINDLE SCALE");
if (emcmotCommand->scale < 0.0) {
emcmotCommand->scale = 0.0; /* clamp it */
}
emcmotStatus->spindle_scale = emcmotCommand->scale;
break;
case EMCMOT_SS_ENABLE:
/* enable/disable overriding spindle speed */
/* can happen at any time */
if ( emcmotCommand->mode != 0 ) {
rtapi_print_msg(RTAPI_MSG_DBG, "SPINDLE SCALE: ON");
emcmotStatus->enables_new |= SS_ENABLED;
} else {
rtapi_print_msg(RTAPI_MSG_DBG, "SPINDLE SCALE: OFF");
emcmotStatus->enables_new &= ~SS_ENABLED;
}
break;
case EMCMOT_AF_ENABLE:
/* enable/disable adaptive feedrate override from HAL pin */
/* can happen at any time */
if ( emcmotCommand->flags != 0 ) {
rtapi_print_msg(RTAPI_MSG_DBG, "ADAPTIVE FEED: ON");
emcmotStatus->enables_new |= AF_ENABLED;
} else {
rtapi_print_msg(RTAPI_MSG_DBG, "ADAPTIVE FEED: OFF");
emcmotStatus->enables_new &= ~AF_ENABLED;
}
break;
case EMCMOT_DISABLE:
/* go into disable */
/* can happen at any time */
/* reset the emcmotDebug->enabling flag to defer disable until
controller cycle (it *will* be honored) */
rtapi_print_msg(RTAPI_MSG_DBG, "DISABLE");
emcmotDebug->enabling = 0;
if (kinType == KINEMATICS_INVERSE_ONLY) {
emcmotDebug->teleoperating = 0;
emcmotDebug->coordinating = 0;
}
break;
case EMCMOT_ENABLE:
/* come out of disable */
/* can happen at any time */
/* set the emcmotDebug->enabling flag to defer enable until
controller cycle */
rtapi_print_msg(RTAPI_MSG_DBG, "ENABLE");
if ( *(emcmot_hal_data->enable) == 0 ) {
reportError("can't enable motion, enable input is false");
} else {
emcmotDebug->enabling = 1;
if (kinType == KINEMATICS_INVERSE_ONLY) {
emcmotDebug->teleoperating = 0;
emcmotDebug->coordinating = 0;
}
}
break;
case EMCMOT_ACTIVATE_JOINT:
/* make axis active, so that amps will be enabled when system is
enabled or disabled */
/* can be done at any time */
rtapi_print_msg(RTAPI_MSG_DBG, "ACTIVATE_JOINT");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
if (joint == 0) {
break;
}
SET_JOINT_ACTIVE_FLAG(joint, 1);
break;
case EMCMOT_DEACTIVATE_JOINT:
/* make axis inactive, so that amps won't be affected when system
is enabled or disabled */
/* can be done at any time */
rtapi_print_msg(RTAPI_MSG_DBG, "DEACTIVATE_AXIS");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
if (joint == 0) {
break;
}
SET_JOINT_ACTIVE_FLAG(joint, 0);
break;
/*! \todo FIXME - need to replace the ext function */
case EMCMOT_ENABLE_AMPLIFIER:
/* enable the amplifier directly, but don't enable calculations */
/* can be done at any time */
rtapi_print_msg(RTAPI_MSG_DBG, "ENABLE_AMP");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
if (joint == 0) {
break;
}
/*! \todo Another #if 0 */
#if 0
extAmpEnable(axis, 1);
#endif
break;
case EMCMOT_DISABLE_AMPLIFIER:
/* disable the axis calculations and amplifier, but don't disable
calculations */
/* can be done at any time */
rtapi_print_msg(RTAPI_MSG_DBG, "DISABLE_AMP");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
if (joint == 0) {
break;
}
/*! \todo Another #if 0 */
#if 0
extAmpEnable(axis, 0);
#endif
break;
case EMCMOT_HOME:
/* home the specified axis */
/* need to be in free mode, enable on */
/* this just sets the initial state, then the state machine in
control.c does the rest */
rtapi_print_msg(RTAPI_MSG_DBG, "HOME");
rtapi_print_msg(RTAPI_MSG_DBG, " %d", joint_num);
if (emcmotStatus->motion_state != EMCMOT_MOTION_FREE) {
/* can't home unless in free mode */
reportError("must be in joint mode to home");
return;
}
if (!GET_MOTION_ENABLE_FLAG()) {
break;
}
if(joint_num == -1) {
if(emcmotStatus->homingSequenceState == HOME_SEQUENCE_IDLE)
emcmotStatus->homingSequenceState = HOME_SEQUENCE_START;
else
reportError("homing sequence already in progress");
break;
}
if (joint == NULL) {
break;
}
if(joint->home_state != HOME_IDLE) {
reportError("homing already in progress");
} else if(emcmotStatus->homingSequenceState != HOME_SEQUENCE_IDLE) {
reportError("homing sequence already in progress");
} else {
/* abort any movement (jog, etc) that is in progress */
joint->free_tp_enable = 0;
/* prime the homing state machine */
joint->home_state = HOME_START;
}
break;
case EMCMOT_ENABLE_WATCHDOG:
rtapi_print_msg(RTAPI_MSG_DBG, "ENABLE_WATCHDOG");
/*! \todo Another #if 0 */
#if 0
emcmotDebug->wdEnabling = 1;
emcmotDebug->wdWait = emcmotCommand->wdWait;
if (emcmotDebug->wdWait < 0) {
emcmotDebug->wdWait = 0;
}
#endif
break;
case EMCMOT_DISABLE_WATCHDOG:
rtapi_print_msg(RTAPI_MSG_DBG, "DISABLE_WATCHDOG");
/*! \todo Another #if 0 */
#if 0
emcmotDebug->wdEnabling = 0;
#endif
break;
case EMCMOT_CLEAR_PROBE_FLAGS:
rtapi_print_msg(RTAPI_MSG_DBG, "CLEAR_PROBE_FLAGS");
emcmotStatus->probing = 0;
break;
case EMCMOT_PROBE:
/* most of this is taken from EMCMOT_SET_LINE */
/* emcmotDebug->queue up a linear move */
/* requires coordinated mode, enable off, not on limits */
rtapi_print_msg(RTAPI_MSG_DBG, "PROBE");
if (!GET_MOTION_COORD_FLAG() || !GET_MOTION_ENABLE_FLAG()) {
reportError
("need to be enabled, in coord mode for probe move");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_COMMAND;
SET_MOTION_ERROR_FLAG(1);
break;
} else if (!inRange(emcmotCommand->pos)) {
if(emcmotCommand->id > 0)
reportError("probe move on line %d would exceed limits",
emcmotCommand->id);
else
reportError("probe move in MDI would exceed limits");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_PARAMS;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
} else if (!limits_ok()) {
reportError("can't do probe move with limits exceeded");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_PARAMS;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
}
/* append it to the emcmotDebug->queue */
tpSetId(&emcmotDebug->queue, emcmotCommand->id);
if (-1 == tpAddLine(&emcmotDebug->queue, emcmotCommand->pos, emcmotCommand->motion_type, emcmotCommand->vel, emcmotCommand->ini_maxvel, emcmotCommand->acc, emcmotStatus->enables_new)) {
reportError("can't add probe move");
emcmotStatus->commandStatus = EMCMOT_COMMAND_BAD_EXEC;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
} else {
emcmotStatus->probing = 1;
SET_MOTION_ERROR_FLAG(0);
/* set flag that indicates all axes need rehoming, if any
axis is moved in joint mode, for machines with no forward
kins */
rehomeAll = 1;
}
break;
case EMCMOT_RIGID_TAP:
/* most of this is taken from EMCMOT_SET_LINE */
/* emcmotDebug->queue up a linear move */
/* requires coordinated mode, enable off, not on limits */
rtapi_print_msg(RTAPI_MSG_DBG, "RIGID_TAP");
if (!GET_MOTION_COORD_FLAG() || !GET_MOTION_ENABLE_FLAG()) {
reportError
("need to be enabled, in coord mode for rigid tap move");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_COMMAND;
SET_MOTION_ERROR_FLAG(1);
break;
} else if (!inRange(emcmotCommand->pos)) {
if(emcmotCommand->id > 0)
reportError("rigid tap move on line %d would exceed limits",
emcmotCommand->id);
else
reportError("rigid tap move in MDI would exceed limits");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_PARAMS;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
} else if (!limits_ok()) {
reportError("can't do rigid tap move with limits exceeded");
emcmotStatus->commandStatus = EMCMOT_COMMAND_INVALID_PARAMS;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
}
/* append it to the emcmotDebug->queue */
tpSetId(&emcmotDebug->queue, emcmotCommand->id);
if (-1 == tpAddRigidTap(&emcmotDebug->queue, emcmotCommand->pos, emcmotCommand->vel, emcmotCommand->ini_maxvel, emcmotCommand->acc, emcmotStatus->enables_new)) {
reportError("can't add rigid tap move");
emcmotStatus->commandStatus = EMCMOT_COMMAND_BAD_EXEC;
tpAbort(&emcmotDebug->queue);
SET_MOTION_ERROR_FLAG(1);
break;
} else {
SET_MOTION_ERROR_FLAG(0);
}
break;
case EMCMOT_SET_TELEOP_VECTOR:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_TELEOP_VECTOR");
if (!GET_MOTION_TELEOP_FLAG() || !GET_MOTION_ENABLE_FLAG()) {
reportError
("need to be enabled, in teleop mode for teleop move");
} else {
double velmag;
emcmotDebug->teleop_data.desiredVel = emcmotCommand->pos;
pmCartMag(emcmotDebug->teleop_data.desiredVel.tran, &velmag);
if (emcmotDebug->teleop_data.desiredVel.a > velmag) {
velmag = emcmotDebug->teleop_data.desiredVel.a;
}
if (emcmotDebug->teleop_data.desiredVel.b > velmag) {
velmag = emcmotDebug->teleop_data.desiredVel.b;
}
if (emcmotDebug->teleop_data.desiredVel.c > velmag) {
velmag = emcmotDebug->teleop_data.desiredVel.c;
}
if (velmag > emcmotConfig->limitVel) {
pmCartScalMult(emcmotDebug->teleop_data.desiredVel.tran,
emcmotConfig->limitVel / velmag,
&emcmotDebug->teleop_data.desiredVel.tran);
emcmotDebug->teleop_data.desiredVel.a *=
emcmotConfig->limitVel / velmag;
emcmotDebug->teleop_data.desiredVel.b *=
emcmotConfig->limitVel / velmag;
emcmotDebug->teleop_data.desiredVel.c *=
emcmotConfig->limitVel / velmag;
}
/* flag that all joints need to be homed, if any joint is
jogged individually later */
rehomeAll = 1;
}
break;
case EMCMOT_SET_DEBUG:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_DEBUG");
emcmotConfig->debug = emcmotCommand->debug;
emcmot_config_change();
break;
/* needed for synchronous I/O */
case EMCMOT_SET_AOUT:
if (emcmotCommand->now) { //we set it right away
emcmotAioWrite(emcmotCommand->out, emcmotCommand->minLimit);
} else { // we put it on the TP queue, warning: only room for one in there, any new ones will overwrite
tpSetAout(&emcmotDebug->queue, emcmotCommand->out,
emcmotCommand->start, emcmotCommand->end);
}
break;
case EMCMOT_SET_DOUT:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_DOUT");
if (emcmotCommand->now) { //we set it right away
emcmotDioWrite(emcmotCommand->out, emcmotCommand->start);
} else { // we put it on the TP queue, warning: only room for one in there, any new ones will overwrite
tpSetDout(&emcmotDebug->queue, emcmotCommand->out,
emcmotCommand->start, emcmotCommand->end);
}
break;
case EMCMOT_SET_SPINDLE_VEL:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_SPINDLE_VEL");
emcmotStatus->spindle.speed = emcmotCommand->vel;
break;
case EMCMOT_SPINDLE_ON:
rtapi_print_msg(RTAPI_MSG_DBG, "SPINDLE_ON");
emcmotStatus->spindle.speed = emcmotCommand->vel;
emcmotStatus->spindle.css_factor = emcmotCommand->ini_maxvel;
emcmotStatus->spindle.xoffset = emcmotCommand->acc;
if (emcmotCommand->vel >= 0) {
emcmotStatus->spindle.direction = 1;
} else {
emcmotStatus->spindle.direction = -1;
}
emcmotStatus->spindle.brake = 0; //disengage brake
break;
case EMCMOT_SPINDLE_OFF:
rtapi_print_msg(RTAPI_MSG_DBG, "SPINDLE_OFF");
emcmotStatus->spindle.speed = 0;
emcmotStatus->spindle.direction = 0;
emcmotStatus->spindle.brake = 1; // engage brake
break;
case EMCMOT_SPINDLE_INCREASE:
rtapi_print_msg(RTAPI_MSG_DBG, "SPINDLE_INCREASE");
if (emcmotStatus->spindle.speed > 0) {
emcmotStatus->spindle.speed += 100; //FIXME - make the step a HAL parameter
} else if (emcmotStatus->spindle.speed < 0) {
emcmotStatus->spindle.speed -= 100;
}
break;
case EMCMOT_SPINDLE_DECREASE:
rtapi_print_msg(RTAPI_MSG_DBG, "SPINDLE_DECREASE");
if (emcmotStatus->spindle.speed > 100) {
emcmotStatus->spindle.speed -= 100; //FIXME - make the step a HAL parameter
} else if (emcmotStatus->spindle.speed < -100) {
emcmotStatus->spindle.speed += 100;
}
break;
case EMCMOT_SPINDLE_BRAKE_ENGAGE:
rtapi_print_msg(RTAPI_MSG_DBG, "SPINDLE_BRAKE_ENGAGE");
emcmotStatus->spindle.speed = 0;
emcmotStatus->spindle.direction = 0;
emcmotStatus->spindle.brake = 1;
break;
case EMCMOT_SPINDLE_BRAKE_RELEASE:
rtapi_print_msg(RTAPI_MSG_DBG, "SPINDLE_BRAKE_RELEASE");
emcmotStatus->spindle.brake = 0;
break;
case EMCMOT_SET_JOINT_COMP:
rtapi_print_msg(RTAPI_MSG_DBG, "SET_JOINT_COMP for joint %d", joint_num);
if (joint == 0) {
break;
}
if (joint->comp.entries >= EMCMOT_COMP_SIZE) {
reportError("joint %d: too many compensation entries", joint_num);
break;
}
/* point to last entry */
comp_entry = &(joint->comp.array[joint->comp.entries]);
if (emcmotCommand->comp_nominal <= comp_entry[0].nominal) {
reportError("joint %d: compensation values must increase", joint_num);
break;
}
/* store data to new entry */
comp_entry[1].nominal = emcmotCommand->comp_nominal;
comp_entry[1].fwd_trim = emcmotCommand->comp_forward;
comp_entry[1].rev_trim = emcmotCommand->comp_reverse;
/* calculate slopes from previous entry to the new one */
if ( comp_entry[0].nominal != -HUGE_VAL ) {
/* but only if the previous entry is "real" */
tmp1 = comp_entry[1].nominal - comp_entry[0].nominal;
comp_entry[0].fwd_slope =
(comp_entry[1].fwd_trim - comp_entry[0].fwd_trim) / tmp1;
comp_entry[0].rev_slope =
(comp_entry[1].rev_trim - comp_entry[0].rev_trim) / tmp1;
} else {
/* previous entry is at minus infinity, slopes are zero */
comp_entry[0].fwd_trim = comp_entry[1].fwd_trim;
comp_entry[0].rev_trim = comp_entry[1].rev_trim;
}
joint->comp.entries++;
break;
default:
rtapi_print_msg(RTAPI_MSG_DBG, "UNKNOWN");
reportError("unrecognized command %d", emcmotCommand->command);
emcmotStatus->commandStatus = EMCMOT_COMMAND_UNKNOWN_COMMAND;
break;
} /* end of: command switch */
if (emcmotStatus->commandStatus != EMCMOT_COMMAND_OK) {
rtapi_print_msg(RTAPI_MSG_DBG, "ERRROR: %d",
emcmotStatus->commandStatus);
}
rtapi_print_msg(RTAPI_MSG_DBG, "\n");
/* synch tail count */
emcmotStatus->tail = emcmotStatus->head;
emcmotConfig->tail = emcmotConfig->head;
emcmotDebug->tail = emcmotDebug->head;
}
/* end of: if-new-command */
check_stuff ( "after command_handler()" );
return;
}